Spectroscopic properties and thermal stability of Er3+-doped tungsten-tellurite glass for waveguide amplifier application

Tungsten-tellurite glass with molar composition of 60TeO(2)-30WO(3)-10Na(2)O has been investigated for developing planar broadband waveguide amplifier application. Spectroscopic properties and thermal stability of Er3+-doped tungsten-tellurite glass have been discussed. The results show that the introduction Of WO3 increases significantly the glass transition temperature and the maximum phonon energy. Er3+-doped tungsten-tellurite glass exhibits high glass transition temperature (377 degrees C), large emission cross-section (0.91 x 10(-20) cm(2)) at 1532 nm and broad full width at half maximum (FWHM), which make it preferable for broadband Er3+-doped waveguide amplifier application. (c) 2005 Elsevier B.V. All rights reserved.

Edge-defined, film-fed growth (EFG) technique for the preparation of alpha-Al2O3 : C crystal with highly sensitive thermoluminescence response

In this work, alpha-Al2O3:C, a highly sensitive thermoluminescence dosimetry crystal, was grown by the EFG method in which a graphite heating unit and shield acted as the carbon source during the growth process. The optical, luminescent properties and dosimetric characteristics of the crystal were investigated. The as-grown crystal shows a single glow peak at 536 K, which is associated with Cr3+ ions. After annealing in H-2 at 1673 K for 80 h, the crystal shows a single glow peak at 460 K and a blue emission band at 415 nm. The thermoluminescent response of the annealed crystal shows linear-sublinear-saturation characteristics in the dose range from 5 x 10(-6) to 100 Gy.

蹄蝠科的核型进化：比较染色体涂色、G带和C带分析

：与其姐妹科(菊头蝠科)相比，蹄蝠科的细胞遗传学研究较少。迄今为止，仅少数蹄蝠科几个物种有高分辨率的G带核型报道，且有关该科核型进化的大多数结论都是基于常规Giemsa染色研究而得。该研究利用三叶小蹄蝠的染色体特异探针，通过比较染色体涂色、G和C显带，建立了5种蹄蝠的染色体同源性图谱，并探讨了它们同源染色体间的G和C带异同。结果表明：罗伯逊易位、臂内倒位以及异染色质的扩增可能是蹄蝠科物种核型进化的主要机制。通过对这5种蹄蝠物种及其外群物种之间的同源染色体片段的比较分析，作者推测蹄蝠科的祖先核型并不像先前认为的全由端着丝粒染色体组成, 而应该含有中着丝粒染色体。

激波管壁AlO自由基B~2∑~+-X~2∑~+和C~2∏_r-X~2∑~+带系辐射光谱的研究

爆轰驱动过程中产生的高温高压气流对铝质膜片、激波管壁产生烧蚀和冲刷作用,以致激波管壁、端盖上附有氧化铝等杂质,而高温下AlO自由基在气体分子的高速碰撞下被激发并产生强烈的辐射,从而干扰了高温气体辐射光谱的分析。用爆轰驱动加热技术将空气加热到4 000~7 000 K,利用多通道光学分析仪对AlO自由基辐射光谱进行分析,实验发现在460~530 nm波长范围内有多支辐射非常强烈的AlO自由基B2Σ+-X2Σ+(T00=20 689 cm-1)带系辐射谱带,且每支谱带都由多个带头组成,带头间隔约为2 nm,带头处于高频位置并向低频方向伸延。通过实验与理论计算相结合,重点分析了AlO自由基B2Σ+-X2Σ+带系辐射光谱的结构特征。AlO自由基C2Πr-X2Σ+(T00=33 047 cm-1)带系辐射光谱处于270~335 nm波长范围内,其辐射强度相对于B2Σ+-X2Σ+带系较弱,并且与OH基A2Σ+-X2Π(T00=32 682 cm-1)带系辐射光谱互相干扰而难以分辨,对该波段高温空气的辐射光谱分析产生不利的影响。

醛酮类化合物的~(13)C核磁共振波谱模拟

为饱和醛酮类化合物的1 3C核磁共振波谱模拟 .根据该类化合物的特点 ,提取了分子的拓扑特征 ,几何特征及电子特征 .应用变量最优子集回归法进行了变量的选择 ,并用这些变量构造了回归模型 .交叉验证的结果表明 ,所得数学模型比较稳定 ,并得到了较好的预测结果

REDOX THERMODYNAMICS OF CYTOCHROME-C AT THE BARE GLASSY-CARBON ELECTRODE

Investigation of the redox thermodynamics of horse heart cytochrome c at bare glassy carbon electrodes has been performed using cyclic voltammetry with a nonisothermal electrochemical cell. The thermodynamic parameters of the electron-transfer reaction of cytochrome c have been estimated in different component buffer solutions. The change DELTAS(re)-degrees in reaction center entropy and the formal potential E-degrees' (at 25-degrees-C, vs. standard hydrogen electrode (SHE)) for cytochrome c are found to be -64.1 J K-1 mol-1 and 0.251 V in phosphate buffer, -64.8 J K-1 mol-1 and 0.257 V in Tris + HCl buffer, -65.6 J K-1 mol-1 and 0.261 V in Tris+CH3COOH buffer (pH 7.0, ionic strength 100 mM). The temperature dependence of the formal potential obtained in phosphate buffer with or without NaCl in the range 5-55-degrees-C shows biphase characteristics in an alkaline solution with an intersection point at ca. 44-degrees-C or 42-degrees-C, which should be due to a structural change in the protein moiety of cytochrome c. However, in acidic and neutral solutions only a monotonic relationship between E-degrees' and temperature is observed. The effect of the buffer component on E-degrees' for cytochrome c is also discussed.

1,2-聚丁二烯~(13)C-NMR弛豫的溶剂效应

本文测定了一系列具有不同微观结构的1,2-聚丁二烯样品在四种溶剂的50.3MHz ~(13)C自旋-晶格弛豫时间(T_1)和核Overhauser效应(NOE)值。并用Schaefer logx~2相关时间分布模型对实验数据进行了拟合。研究了1,2-聚丁二烯在溶液中的~(13)C-NMR弛豫的溶剂效应及其与结构的关系。发现聚合物与溶剂的溶解度参数之差△δ越大,聚合物在溶液中协同链段运动趋向越明显,~(13)C自旋-晶格弛豫速率(1/T_1)越大;1,2-链节较少,分子链较柔顺时,~(13)C-NMR弛豫受溶剂影响较显著。NMR弛豫参数对结构变化的反应在良溶剂中比在不良溶剂中敏感。

Anomalous Thermal Stability of Nd-Fe-Co-Al Bulk Metallic Glass

The thermal stability of Nd60Fe20Co10Al10 bulk metallic glass (BMG) has been studied by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), isochronal dilatation and compression tests. The results show that the glass transition of the BMG takes place quite gradually between about 460 and 650 K at a heating rate of 0.17 K/s. Several transformation processes are observed during continuous heating with the first crystallization process beginning at about 460 K, while massive crystallization takes place near the solidus temperature of the alloy. The positive heat of mixing between the two major constituents, Nd and Fe, and, consequently, a highly inhomogeneous composition of the attained amorphous phase are responsible for the anomalous thermal stability in this system. (C) 2002 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

Nonequilibrium microstructures and their evolution in a Fe-Cr-W-Ni-C laser clad coating

The laser-solidified microstructural and compositional characterization and phase evolution during tempering at 963 K were investigated using an analytical transmission electron microscope with energy dispersive X-ray analysis. The cladded alloy, a powder mixture of Fe, Cr, W, Ni, and C with a weight ratio of 10:5:1:1:1, was processed with a 3 kW continuous wave CO2 laser. The processing parameters were 16 mm/s beam scanning speed, 3 mm beam diameter. 2 kW laser power, and 0.3 g/s feed rate. The coating was metallurgically bonded to the substrate, with a maximum thickness of 730 mu m, a microhardness of about 860 Hv and a volumetric dilution ratio of about 6%. Microanalyses revealed that the cladded coating possessed the hypoeutectic microstructure comprising the primary dendritic gamma-austenite and interdendritic eutectic consisted of gamma-austenite and M7C3 carbide. The gamma-austenite was a non-equilibrium phase with extended solid solution of alloying elements and a great deal of defect structures, i.e. a high density of dislocations, twins, and stacking faults existed in gamma phase. During high temperature aging, in situ carbide transformation occurred of M7C3 to M23C6 and M6C. The precipitation of M23C6, MC and M2C carbides from austenite was also observed.

铁基抗高温磨损激光熔覆涂层强韧设计和研究II:Fe-Cr-C-W-Ni激光熔覆层的微观组织及性能

本文以对热工模具进行失效分析的基础上，利用激光熔覆技术，在５ＣｒＭｎＭｏ基础上设计并制备强韧兼备的抗高温磨损涂层。

Measuring Binding Kinetics Of Surface-Bound Molecules Using The Surface Plasmon Resonance Technique

Surface plasmon resonance (SPR) technology and the Biacore biosensor have been widely used to measure the kinetics of biomolecular interactions in the fluid phase. In the past decade, the assay was further extended to measure reaction kinetics when two counterpart molecules are anchored on apposed surfaces. However, the cell binding kinetics has not been well quantified. Here we report development of a cellular kinetic model, combined with experimental procedures for cell binding kinetic measurements, to predict kinetic rates per cell. Human red blood cells coated with bovine serum albumin and anti-BSA monoclonal antibodies (mAbs) immobilized on the chip were used to conduct the measurements. Sensor-grams for BSA-coated RBC binding onto and debinding from the anti-BSA mAb-immobilized chip were obtained using a commercial Biacore 3000 biosensor, and analyzed with the cellular kinetic model developed. Not only did the model fit the data well, but it also predicted cellular on and off-rates as well as binding affinities from curve fitting. The dependence of flow duration, flow rate, and site density of BSA on binding kinetics was tested systematically, which further validated the feasibility and reliability of the new approach. Crown copyright (c) 2008 Published by Elsevier Inc. All rights reserved.

裂纹顶端位错的运动和小范围屈服的K_(Ⅱc)

本文从裂纹顶端位错运动的简化模型估计形成塑性区所消耗的功;从而计算临界裂纹扩展力。由于Ⅰ型加载和Ⅱ型加载的应力状态有所不同,裂纹顶端塑性功耗也会不一样。基于上述思想,考虑了小范围屈服的K_(Ⅰc)和K_(Ⅱc)的关系,得出K(Ⅱc)>K(Ⅰc)的结论,符合实验结果;并就K(Ⅱc)/K(Ⅰc)的比值与材料性能和温度的关系作了讨论。

铁基抗高温磨损激光熔覆涂层强韧设计和研究 Ⅱ:Fe-Cr-C-W-Ni激光熔覆层的微观组织及性能

利用ＯＭ、ＳＥＭ、ＴＥＭ研究了Ｆｅ－Ｃｒ－Ｃ－Ｗ－Ｎｉ激光熔覆涂层熔覆态及其高温时效态的微观组织结构。结果表明激光熔覆层组织细小，具有强韧两相组成（奥氏体和Ｍ_７Ｃ_３碳化物）的微观结构特征，高温时效处理组织中有Ｍ_（２３）Ｃ_６、Ｍ_６Ｃ、Ｍ_２Ｃ等新碳化物形成。显微硬度和冲击磨损实验证实了激光熔覆态和峰值时效态熔覆层均具有良好的力学性能。

钾离子通道Kir2.1/C-末端功能区的分子动力学模拟

<正>内向整流型钾离子通道(Kir,inwardlyrectifyingpotassium)在细胞激活、细胞内外钾离子K~+的动态平衡、胰岛素分泌等细胞生理过程中起重要作用。而细胞内各种不同因素和第二信使对Kir的调控则是实现其不同生理功能的途径。已有实验结果表明,4,5二磷酸磷脂酰肌醇(PIP2,phosphatidylinositol4,5-bisphosphate)与Kir相互作用的强弱决定了Kir对各种调控因素的响应程度。根据Kir2.1与Kir3.1胞内C-末端X-ray