On The Interaction Of Channeling/Segmentation Cracks Of Coating: Study On The Critical Spacing

Channeling/segmentation cracks may arise in the coating subjected to in-plane tensile stress. The interaction between these multiple cracks, say the effect of the spacing between two adjacent cracks oil the behaviors of channels themselves and the interface around the interface corners, attracts wide interest. However, if the spacing is greater than a specific magniture,, namely the Critical Spacing (CS), there should be no interaction between such channeling/segmentation cracks. In this study, file mechanism of the effect of the crack spacing oil the interfacial stress around the interface corner will be Interpreted firstly. Then the existence of the CS will be verified and the relationship between the CS and the so-called stress transfer length Ill coating will be established for plane strain condition. Finally, the dependence of the stress transfer length, simultaneously of the CS, on the sensitive parameters will be investigated with finite element method and expressed with a simple empirical formula. (C) 2007 Elsevier Ltd. All rights reserved.

Evolution of thermoplastic shear localization and related microstructures in Awl/SiCp composites under dynamic compression

The localized shear deformation in the 2024 and 2124 Al matrix composites reinforced with SiC particles was investigated with a split Hopkinson pressure bar (SHPB) at a strain rate of about 2.0x10(3) s(-1). The results showed that the occurrence of localized shear deformation is sensitive to the size of SiC particles. It was found that the critical strain, at which the shear localization occurs, strongly depends on the size and volume fraction of SiC particles. The smaller the particle size, the lower the critical strain required for the shear localization. TEM examinations revealed that Al/SiCp interfaces are the main sources of dislocations. The dislocation density near the interface was found to be high and it decreases with the distance from the particles. The Al matrix in shear bands was highly deformed and severely elongated at low angle boundaries. The Al/SiCp interfaces, particularly the sharp corners of SiC particles, provide the sites for microcrack initiation. Eventual fracture is caused by the growth and coalescence of microcracks along the shear bands. It is proposed that the distortion free equiaxed grains with low dislocation density observed in the center of shear band result from recrystallization during dynamic deformation.

微重力下容器圆形倒角处的毛细驱动流

空间探索计划的需求对空间流体管理技术提出了新的挑战.流体管理设备的内角是主要的流体传输"管道",因此研究微重力下容器内角处的毛细驱动流具有重要的意义.由于设计和制造等原因,完美的尖角并不常见,而是带有一定圆角过渡的内角.笔者设计不同的带有圆形过渡内角的容器,选用10cSt硅油为实验流体介质,通过一系列的落塔实验,研究了容器内角处不同的圆角半径对毛细驱动流的影响,并分析得到了有价值的实验规律.

A new species of the genus Tor from Yunnan, China (Teleostei : Cyprinidae)

A new species of the subfamily Barbinae, Tor yingjiangensis, is recognized from Yunnan province, China. It can be distinguished from other Tor species by the following combination of characters: last simple dorsal-fin ray osseous and non-serrated; no forward directed predorsal procumbent spine; head length considerably longer than body depth; no tubercles on the snout or sides of the face; 18-20 gill rakers on the outside of first gill arch; 24-26 lateral line scales; median lobe of lower lip short, its posterior margin truncate, not extending to the vertical across the inner corners of the mouth; and the condition of the lower lip consistent in individuals of different sizes. The new species has been misidentified previously as Tor putitora (Hamilton, F. 1822. An account of the fishes found in the River Ganges and its Branches. Edinburgh & London. 405 pp), which occurs in the Ganges and Indus River basins. The new species can easily be distinguished from T. putitora by having 3-3.5 (vs. 2.5) scales from lateral line to pelvic-fin origin, shorter caudal peduncle length (13.0% vs. 17.2% of standard length), lesser body depth (26.4% vs. 24.0% of standard length) and longer caudal peduncle depth (12.0% vs. 10.9% of standard length), no longitudinal stripe present along side of body, and eyes visible in ventral view of head.

Finite-difference time-domain analysis of deformed square cavity filters with a traveling-wave-like filtering response by mode coupling

An add-drop filter based on a perfect square resonator can realize a maximum of only 25% power dropping because the confined modes are standing-wave modes. By means of mode coupling between two modes with inverse symmetry properties, a traveling-wave-like filtering response is obtained in a two-dimensional single square cavity filter with cut or circular corners by finite-difference time-domain simulation. The optimized deformation parameters for an add-drop filter can be accurately predicted as the overlapping point of the two coupling modes in an isolated deformed square cavity. More than 80% power dropping can be obtained in a deformed square cavity filter with a side length of 3.01 mu m. The free spectral region is decided by the mode spacing between modes, with the sum of the mode indices differing by 1. (c) 2007 Optical Society of America.

Analysis of mode characteristics for deformed square resonators by FDTD technique

The mode frequencies and quality factors (Q-factors) in two-dimensional (2-D) deformed square resonators are analyzed by finite-difference time-domain (FDTD) technique. The results show that the deformed square cavities with circular and cut corners have larger Q-factors than the perfect ones at certain conditions. For a square cavity with side length of 2 mu m and refractive index of 3.2, the mode Q-factor can increase 13 times as the perfect corners are replaced by a quarter of circle with radius of 0.3 pm. Furthermore the blue shift with the increasing deformations is found as a result of the reduction in effective resonator area. In square cavities with periodic roughness at sidewalls which maintains the symmetry of the square, the Q-factors of the whisperin gallery (WG)-like modes are still one order of magnitude larger that those of non-WG-like modes. However, the Q-tactors of these two types of modes are of the same order in the square cavity with random roughness. We also find that the rectangular and rhombic deformation largely reduce the Q-factors with the increasing offset and cause the splitting of the doubly degenerate modes due to the breaking of certain symmetry properties.

The whispering gallery mode in photonic crystal ring cavity - art. no. 698438

Whispering gallery modes (WGMs) in microcavities possess ultra-high cavity Q factor. Such microcavity are easy to be fabricated, so WGMs have attracted much attention in the area of photonics and integrated photonic circuits. It is well known that the effect of total internal reflection restricts the size of this mirocavity. Such drawback goes against the integration of photon. However, the photonic crystal microcavities (PCMC) make a breakthrough recently. The WGMs in the PCMC are possible to gain both ultra-high Q and ultra-small mode volume. In this paper, the property of the mode in photonic crystal ring cavity is analyzed by FDTD and PWE. By modifying the airholes in the corners of the ring cavity, we can obtain the WGM. Also the Q factor of WGM in photonic crystal ring cavity is calculated. This favors the design of the photonic crystal microcavity components.

Uniform mems chip temperatures in the nucleate boiling heat transfer region by selecting suitable, medium boiling number range

The not only lower but also uniform MEMS chip temperatures can he reached by selecting suitable boiling number range that ensures the nucleate boiling heat transfer. In this article, boiling heat transfer experiments in 10 silicon triangular microchannels with the hydraulic diameter of 55.4 mu m were performed using acetone as the working fluid, having the inlet liquid temperatures of 24-40 degrees C, mass fluxes of 96-360 kg/m(2)s, heat fluxes of 140-420 kW/m(2), and exit vapor mass qualities of 0.28-0.70. The above data range correspond to the boiling number from 1.574 x 10(-3) to 3.219 x 10(-3) and ensure the perfect nucleate boiling heat transfer region, providing a very uniform chip temperature distribution in both streamline and transverse directions. The boiling heat transfer coefficients determined by the infrared radiator image system were found to he dependent on the heat Axes only, not dependent on the mass Axes and the vapor mass qualities covering the above data range. The high-speed flow visualization shows that the periodic flow patterns take place inside the microchannel in the time scale of milliseconds, consisting of liquid refilling stage, bubble nucleation, growth and coalescence stage, and transient liquid film evaporation stage in a full cycle. The paired or triplet bubble nucleation sites can occur in the microchannel corners anywhere along the flow direction, accounting for the nucleate boiling heat transfer mode. The periodic boiling process is similar to a series of bubble nucleation, growth, and departure followed by the liquid refilling in a single cavity for the pool boiling situation. The chip temperature difference across the whole two-phase area is found to he small in a couple of degrees, providing a better thermal management scheme for the high heat flux electronic components. Chen's [11 widely accepted correlation for macrochannels and Bao et al.'s [21 correlation obtained in a copper capillary tube with the inside diameter of 1.95 mm using R11 and HCFC123 as working fluids can predict the present experimental data with accepted accuracy. Other correlations fail to predict the correct heat transfer coefficient trends. New heat transfer correlations are also recommended.

Quantum coherent networks: A theoretical study

Electron transport in quantum coherent networks (interacting quantum waveguide arrays) is investigated theoretically with use of the scattering-matrix method. The scattering matrix for the basic unit of networks, the cross junction with Square or rounded corners, is derived using the mode-matching technique, The overall scattering matrix for the network is obtained by the composition of the scattering matrices associated with each unit of the network, For a uniform network, the transmission spectra are calculated in the single-mode regime and an found notably dependent on the junction geometry. Small reflection for the input terminal and uniform output for some output ports are obtained, which means that the quantum coherent network can be used as a distributing net for the electron waves. Cross junctions with rounded corners of large radii are found to play a negative role in the device application of quantum coherent networks. (C) 1997 American Institute of Physics.

Design of Topas photonic bandgap fiber with high birefringence and low confinement loss

A highly birefringent hollow-core photonic bandgap fiber based on Topas cyclic olefin copolymer is designed. The rhombic hollow-core with rounded corners is formed by omitting four central air holes of the cladding structure. The guided modes, birefringence and confinement loss of the fiber are investigated by using the full-vector finite element method. A high phase birefringence of the order of 10(-3), a group birefringence of the order of 10(-2) and confinement loss less than 0.1 dB/km are obtained at the central wavelength (1.55 mu m) range of the bandgap for fiber with seven rings of air holes in the cladding region. (C) 2010 Elsevier B.V. All rights reserved.

Synthesis, structure and photochromic properties of a novel 1,6-hexanediamine trimolybdate supramolecular compound

A novel supramolecular compound 1,6-hexanediamine trimolybdate ((C6H18N2[Mo3O10], denoted as HDAMo) has been synthesized by a hydrothermal method and its structure has been characterized by elemental analyses, Fourier transform infrared (FT-IR) spectra, single-crystal X-ray diffraction (XRD) technique. This single crystal compound consists of protonated 1,6-hexanediamine (HDA) cations and polyoxometalate [Mo3O10](2-) anions. Its crystal structure belongs to monoclinic system (space group P2(1)/n) with a = 7.7508(14), b = 11.467(2), c = 16.167(3) angstrom, beta = 92.689(3)degrees, V = 143 5.3(5) angstrom(3), Z = 4 and D-ealc = 2.619 g cm(-3). The final statistics based on F-2 are GOF = 0.980, R-1 = 0.0261 and wR(2) = 0.0506 for I > 2 sigma(I). XRD analysis revealed that in the crystal structure of HDAMo, novel infinite [Mo3O10](2-) chains parallel to a axis are made up of distorted MoO6 octahedra connected by corners and edges. The protonated HDA cations occupy channels formed by [Mo(3)O3(10)](2-) Chains and exhibit strong hydrogen bond interactions to terminal and bridging oxo groups of the chains. The [Mo3O10](2-) chains linked through protonated HAD cations formed a one-dimensional network. The HDAMo compound shows novel photochromic properties, i.e., its color changes from white to reddish brown gradually under UV irradiation. XRD, FT-IR, ESR spectra and XPS are used to investigate the photochromic behavior of the compound.

Solvent-induced crystallization of spherical micelles formed by copolymer blends

We have followed the morphological evolution and crystallization process of spherical micelles formed by the mixture of polystyrene-b-poly(acrylic acid) (PS-b-PAA) and polystyrene-b-poly(2-vinylpyridine)b-poly(ethylene oxide) (PS-b-P2VP-b-PEO) (the core of the spherical micelles was made of P2VP and PAA blocks through hydrogen bonding in neutral solvent N,N-dimethylformamide, DMF) via DMF vapor treatment. Different phenomena, such as rupture of the film, formation of cylinder aggregates and regular square lamellae, were observed when the micelle film was treated in DMF for different times. At the early stage of annealing in DMF vapor, the micelle film became unstable and ruptured. Cylinder aggregates, within which the PEO blocks achieved the association and primary chain folding, formed as the mesophases before the nucleation of the PEO single crystals at this stage. Further treatment in DMF vapor resulted in the nucleation of the PEO blocks at the corners of quasi-square lamellae. Then a quite regular "sandwich" lamellar structure, constructed by a PEO single-crystal layer covered by two tethered layers of other amorphous blocks on the top and bottom crystal basal surfaces, formed when the film of micelles was annealed in DMF vapor for sufficient times.

地震波模拟：非规则网格离散的数值解法、吸收边界及其实际应用

This dissertation presents a series of irregular-grid based numerical technique for modeling seismic wave propagation in heterogeneous media. The study involves the generation of the irregular numerical mesh corresponding to the irregular grid scheme, the discretized version of motion equations under the unstructured mesh, and irregular-grid absorbing boundary conditions. The resulting numerical technique has been used in generating the synthetic data sets on the realistic complex geologic models that can examine the migration schemes. The motion equation discretization and modeling are based on Grid Method. The key idea is to use the integral equilibrium principle to replace the operator at each grid in Finite Difference scheme and variational formulation in Finite Element Method. The irregular grids of complex geologic model is generated by the Paving Method, which allow varying grid spacing according to meshing constraints. The grids have great quality at domain boundaries and contain equal quantities of nodes at interfaces, which avoids the interpolation of parameters and variables. The irregular grid absorbing boundary conditions is developed by extending the Perfectly Matched Layer method to the rotated local coordinates. The splitted PML equations of the first-order system is derived by using integral equilibrium principle. The proposed scheme can build PML boundary of arbitrary geometry in the computational domain, avoiding the special treatment at corners in a standard PML method and saving considerable memory and computation cost. The numerical implementation demonstrates the desired qualities of irregular grid based modeling technique. In particular, (1) smaller memory requirements and computational time are needed by changing the grid spacing according to local velocity; (2) Arbitrary surfaces and interface topographies are described accurately, thus removing the artificial reflection resulting from the stair approximation of the curved or dipping interfaces; (3) computational domain is significantly reduced by flexibly building the curved artificial boundaries using the irregular-grid absorbing boundary conditions. The proposed irregular grid approach is apply to reverse time migration as the extrapolation algorithm. It can discretize the smoothed velocity model by irregular grid of variable scale, which contributes to reduce the computation cost. The topography. It can also handle data set of arbitrary topography and no field correction is needed.