Recent 2000-year geological records of mud in the inner shelf of the East China Sea and their climatic implications

AXIS(14)C dating and grain-size analysis for Core DD2, located at the north of the Yangtze River-derived mud off the Zhejiang-Fujian coasts in the inner shelf of the East China Sea, provide us a high-resolution grain-size distribution curve varying with depth and time. Data in the upper mud layer of Core DD2 indicate that there are at least 9 abrupt grain-size increasing in recent 2000 years, with each corresponding very well with the low-temperature events in Chinese history, which might result from the periodical strengthening of the East Asian Winter Monsoon (EAWM), including the first-revealed maximum temperature lowering event at around 990 a BP. At the same time, the finer grain size section in Core DD2 agrees well with the Sui-Tang Warming Period (600-1000 a AD) defined previously by Zhu Kezhen, during which the climate had a warm, cold and warm fluctuation, with a dominated cooling period of 750-850 a AD. The Little Ice Age (LIA) can also be identified in the core. It starts around 1450 a AD and was followed by a subsequent cooling events at 1510, 1670 and 1840 a AD. Timing of these cold events revealed here still needs to be further verified owing to some current uncertainty of dating we used in this study.

Mud mass transport due to waves based on an empirical rheology model featured by hysteresis loop

A vertical 2-D water-mud numerical model is developed for estimating the rate of mud mass transport under wave action. A nonlinear semi-empirical rheology model featured by remarkable hysteresis loops in the relationships of the shear stress versus both the shear strain and the rate of shear strain of mud is applied to this water mud model. A logarithmic grid in the vertical direction is employed for numerical treatment, which increases the resolution of the flow in the neighborhood of both sides of the interface. Model verifications are given through comparisons between the calculated and the measured mud mass transport velocities as well as wave height changes. (C) 2006 Elsevier Ltd. All rights reserved.

青蟹属的系统进化和中国沿海拟穴青蟹的群体遗传结构研究

为了进一步研究青蟹属系统进化的科学问题，并揭示我国东南沿海青蟹群体遗传结构和群体进化细节信息，本论文主要开展了以下两个方面的研究：（1）基于线粒体12S rRNA、16S rRNA和COI三种基因序列探讨中国东南沿海青蟹的种类归属与青蟹属的系统进化；（2）利用线粒体COI基因标记分析中国东南沿海拟穴青蟹的群体遗传结构。序列特征、遗传距离和系统进化分析结果都表明本文研究的青蟹均为S. paramamosain。NJ、BAYES和ML系统进化树显示S. paramamosain与S. tranquebarica互为姐妹种，S. olivecea应该是4种青蟹中最早分化出来的种类。10个地理群体130只拟穴青蟹的线粒体DNA（mitochondrial DNA，mtDNA）细胞色素氧化酶亚基I（COI）基因序列Mantel检验结果显示群体间的遗传分化程度与地理距离没有显著的相关性。分子进化中性检验结果表明自然选择在分子进化过程中起了重要作用，并暗示该物种在最近经历了一个快速的群体爆发及扩张事件。

砂泥岩储层测井产能预测方法研究

Productivity prediction is very important in the exploration and development of oilfields. Using well log data to predict productivity is a front-line technology， which is key issue in petroleum exploration phase. The essential factors of productivity prediction is building practical models and correcting various causes to improve precision of prediction parameters. Any errors of parameters selections can affect the calculation of productivity prediction; therefore， how to improve research means and calculation accuracy is an important task of productivity prediction. Theory and case examples are deeply and comprehensively studied in the paper. Based on the theory of mud-filtrate invasion and experimental results， the damage of drilling， cementing， perforating，acidizing and fracturing were investigated. The damage depth was quantitatively evaluated by log data， based on this， the processing results of reservoir sensitivity were used to analysis quantitatively the damage of reservoir. The productivity prediction and reservoir damage were initiatively incorporated according to well logging， and the precision of productivity prediction was effectively improved. The method of NMR was explored to calculate the fluid viscosity on the basis of reservoir physical method， and the differences between the two methods were compared in the paper. From the theory fluid flow in porous media， various of theoretical models of production prediction were explored and several practical models were consided， such as productivity index method， improved productivity index method， improved Bearder method， SVM and so on. The characteristic and the application scope of these methods were studied. The inflow productivity and outflow productivity were incorporated and nodal analysis method was used to forecast wellhead yield， thus achieved scientifically production. On the applied background of conventional logging suite， the applying of special items or new logging method which is practical in the research area were studied， the logging suite was further optimized， and the precision of forecast was improved. On the basis of the modeling and the calculation of parameters， these methods were verified and analyzed， and the reconstruct principle was also built for block reservoir. The research block was processed by these methods and compared with testing data. Based on above the research， a technological system which is practical for shaly sand profiles in Shengli Oilfield was built. The system can reach commercialized degree，and satisfied the need of exploration and development of the oilfield.

东海陆架盆地西南部烟囱构造与油气运聚关系研究

In recent years, chimney structure has been proved one of important indicators and a useful guide to major petroleum fields exploration through their exploration history both at home and abroad. Chimney structure, which has been called "gas chimney" or "seismic chimney", is the special fluid-filled fracture swarm, which results from the boiling of active thermal fluid caused by abruptly decreasing of high pressure and high temperature in sedimentary layers of upper lithosphere. Chimney structure is well developed in continental shelf basin of East China Sea, which indicates the great perspectives of petroleum resources there. However, the chimney structure also complicated the petroleum accumulation. So the study of chimney structure on its formation, its effect on occurrence and distribution of petroleum fields is very important not only on theoretical, but also on its applied research. It is for the first time to make a clear definition of chimney structure in this paper, and the existence and practical meaning of chimney structure are illustrated. Firstly, on the viewpoint of exploration, this will amplify exploration area or field, not only in marine, but also on continent. Secondly, this is very important to step-by-step exploration and development of petroleum fields with overpressure. Thirdly, this will provide reference for the study on complex petroleum system with multi-sources, commingled sources and accumulation, multi-stage accumulations, and multi-suits petroleum system in the overlay basin. Fourthly, when the thermal fluid enters the oceanic shallow layer, it can help form gas hydrate under favorable low-temperature and high-pressure conditions. Meanwhile, the thermal fluid with its particular component and thermal content will affect the physical, chemical and ecological environments, which will help solving the problem of global resources and environment. Beginning from the regional tectonic evolution characteristics, this paper discussed the tectonic evolution history of the Taibei depression, then made an dynamical analysis of the tectonic-sedimentary evolution during the Mesozoic and Cenozoic for the East China Sea basin. A numerical model of the tectonic-thermal evolution of the basin via the Basin-Mod technique was carried out and the subsidence-buried history and thermal history of the Taibei depression were inverse calculated: it had undergone a early rapid rift and sag, then three times of uplift and erosion, and finally depressed and been buried. The Taibei depression contains a huge thick clastic sedimentary rock of marine facies, transitional facies and continental facies on the complex basement of ante-Jurassic. It is a part of the back-arc rifting basins occurred during the Mesozoic and Cenozoic. The author analyzed the diagenesis and thermal fluid evolution of this area via the observation of cathodoluminescence, scanning electron microscope and thin section, taking advantage of the evidences of magma activities, paleo-geothermics and structural movement, the author concluded that there were at least three tectonic-thermal events and three epochs of thermal-fluid activities; and the three epochs of thermal-fluid activities were directly relative to the first two tectonic-thermal events and were controlled by the generation and expulsion of hydrocarbon in the source rock simultaneously. Based on these, this paper established the corresponding model between the tectonic-thermal events and the thermal-fluid evolution of the Taibei Depression, which becomes the base for the study on the chimney structures. According to the analyses of the gas-isotope, LAM spectrum component of fluid inclusion, geneses of CO_2 components and geneses of hydrocarbon gases, the author preliminarily verified four sources of the thermal fluid in the Taibei Depression: ① dehydration of mud shale compaction, ② expulsion of hydrocarbon in the source rock; ③ CO_2 gas hydro-thermal decomposition of carbonatite; ④magma-derived thermal fluid including the mantle magma water and volatile components (such as H_2O, CO_2, H_2S, SO_2, N_2 and He etc.). On the basis of the vitrinite reflectance (Ro), homogenization temperature of fluid inclusion, interval transit time of major well-logging, mud density of the wells, measured pressure data and the results of previous studies, this paper analyzed the characteristics of the geothermal fields and geo-pressure fields for the various parts in this area, and discussed the transversal distribution of fluid pressure. The Taibei depression on the whole underwent a temperature-loss process from hot basin to cold basin; and locally high thermal anomalies occurred on the regional background of moderate thermal structure. The seal was primarily formed during the middle and late Paleocene. The overpressured system was formed during the middle and late Eocene. The formation of overpressured system in Lishui Sag underwent such an evolutionary process as "form-weaken-strengthen-weaken". Namely, it was formed during the middle and late Eocene, then was weakened in the Oligocene, even partly broken, then strengthened after the Miocene, and finally weakened. The existence of the thermal fluid rich in volatile gas is a physical foundation for the boiling of the fluid, and sharply pressure depletion was the major cause for the boiling of the fluid, which suggests that there exists the condition for thermal fluid to boil. According to the results of the photoelastic simulation and similarity physical experiments, the geological condition and the formation mechanism of chimnestructures are summarized: well compartment is the prerequisite for chimney formation; the boiling of active thermal fluid is the original physical condition for chimney formation; The local place with low stress by tension fault is easy for chimney formation; The way that thermal fluid migrates is one of the important factors which control the types of chimney structures. Based on where the thermal fluid come from and geometrical characteristics of the chimney structures, this paper classified the genetic types of chimney structures, and concluded that there existed three types and six subtypes chimney structures: organic chimney structures generated by the hydrocarbon-bearing thermal fluid in middle-shallow layers, inorganic and commingling-genetic chimney structures generated by thermal fluid in middle-deep layers. According to the seismic profiles interpretations, well logging response analysis and mineralogical and petrological characteristics in the study area, the author summarized the comprehensive identification marks for chimney structures. Especially the horizon velocity analysis method that is established in this paper and takes advantage of interval velocity anomaly is a semi-quantitative and reliable method of chimney structure s identification. It was pointed out in this paper that the occurrence of the chimney structures in the Taibei depression made the mechanism of accumulation complicated. The author provided proof of episodic accumulation of hydrocarbon in this area: The organic component in the boiling inclusion is the trail of petroleum migration, showing the causality between the boiling of thermal fluid and the chimney structures, meanwhile showing the paroxysmal accumulation is an important petroleum accumulation model. Based on the evolutionary characteristics of various types of chimney structures, this paper discussed their relationships with the migration-accumulation of petroleum respectively. At the same time, the author summarized the accumulating-dynamical models associated with chimney structures. The author analyzed such accumulation mechanisms as the facies state, direction, power of petroleum migration, the conditions of trap, the accumulation, leakage and reservation of petroleum, and the distribution rule of petroleum. The author also provides explanation for such practical problems the existence of a lot of mantle-derived CO_2, and its heterogeneous distribution on plane. By study on and recognition for chimney structure, the existence and distribution of much mantle-derived CO_2 found in this area are explained. Caused by tectonic thermal activities, the deep magma with much CO_2-bearing thermal fluid migrate upward along deep fault and chimney structures, which makes two wells within relatively short distance different gas composition, such as in well LF-1 and well LS36-1-1. Meanwhile, the author predicted the distribution of petroleum accumulation belt in middle-shallow layer for this area, pointed out the three favorable exploration areas in future, and provided the scientific and deciding references for future study on the commingling-genetic accumulation of petroleum in middle-deep layer and the new energy-gas hydrate.

Simultaneous determination of chromium(VI) and chromium(III) of bioavailable fraction in bottom mud by flow injection-atomic absorption spectroscopy

A rapid and sensitive method for separation and determination of Cr(VI) and Cr(III) in bottom mud of lake by flow injection on-line preconcentrtion system and GFAAS was developed. The available Cr(VI) and Cr(III) were extracted by HOAc or EDTA + NH4 NO3 and adsorbed simultaneously by an anion and a cation resin microclummn and then eluted simultaneously by 2 mol/L NH4 NO3 + 0.05 mol/L ascorbate and 2 mol/L H2SO4, respectively. The elution was performed for 50 s after adsorption for 2 min, and the efficiencies of elution were 85.4% - 94.8% and 96.7% - 106% for Cr(VI) and Cr(M) respectively. The detection limits of the method were 0.9 mu g/L and 2.7 mu g/L with relative standard deviations of 3.5% and 6.4% for the determination of Cr(VI) and Cr(III) in sample, respectively.

Inhibitory effects of the androgenic gland on ovarian development in the mud crab Scylla paramamosain

Isolation and characterization of androgenic hormone in decapod crustaceans depend on an effective bioassay of its action. In the present study, the effect of androgenic gland on ovarian development in the mud crab Scylla paramamosain was investigated with a view to develop a bioassay for androgenic hormone. Ovarian regression with degeneration of oocytes occurred in some female crabs implanted with androgenic gland in vivo. In vitro incubation of ovarian tissues at secondary vitellogenesis in extract of androgenic gland resulted in a significant decrease in amino acid uptake by the tissues. We propose that this inhibitory effect could be established as an effective bioassay for the isolation of androgenic hormone in the mud crab. (c) 2005 Published by Elsevier Inc.

Cold event at 5 500 a BP recorded in mud sediments on the inner shelf of the East China Sea

A 700-year record (1.0-1.5 a resolution) of the East Asian winter monsoon (EAWM), based on grain-size analysis and AMS(14)C dating of Core EC2005 from the inner-shelf mud wedge of the East China Sea (ECS), was compared with the Dongge stalagmite delta O-18 record during the mid-Holocene. The upper muddy section of Core EC2005 has been formed mainly by suspended sediments derived from the Changjiang (Yangtze) River mouth since 7.3 ka BP. High precipitation and a strengthened EAWM might have played key roles in the high sedimentation rate (1 324-1 986 cm/ka) between 5.9-5.2 ka BP. The EAWM strengthened when the Asian summer monsoon weakened, especially around 5 500 a BP, which corresponded to a worldwide cold event. The EAWM during the mid-Holocene shows statistically significant solar periodicities at 62 and 11 a. The 5 500 a BP cold event might be resulted from orbital forcing and changes in solar activity.

Records of the East Asian winter monsoon from the mud area on the inner shelf of the East China Sea since the mid-Holocene

AMS(14)C dating and analysis of grain size, major elements and clay minerals were applied to Core MZ01 from the mud area on the inner shelf of the East China Sea. Based on the environmentally sensitive grain size, clay mineral and major element assemblages, the history of the East Asia winter monsoon since the mid-Holocene could be reconstructed. These three proxies, mean grain size (>9.71 mu m), chemical index of alteration (CIA) and ratio of smectite to kaolinite in particular, show similar fluctuation patterns. Furthermore, 10 extreme values corresponding to the contemporary cooling events could be recognized since the mid-Holocene; these extreme values are likely to have been caused by the strengthening of the East Asia winter monsoon. The cooling events correlated well with the results of the delta O-18 curves of the Dunde ice core and GISP2, which therefore revealed a regional response to global climate change. Four stages of the East Asia winter monsoon were identified, i.e. 8300-6300 a BP, strong and unstable; 6300-3800 a BP, strong but stable; 3800-1400 a BP, weak and unstable; after 1400 a BP, weak but stable.

The characteristics of fluid potential in mud diapirs associated with gas hydrates in the Okinawa Trough

Many mud diapirs have been identified in the southern Okinawa Trough from a seismic survey using R/V KEXUE I in 2001. The movement and accumulation of free gas related to mud diapirs are discussed in detail by an analysis of fluid potential which is based upon velocity data. It can be found that free gas moves from the higher fluid potential strata to the lower ones and the gas hydrate comes into being during free gas movement meeting the proper criteria of temperature and pressure. In fact, gas hydrates have been found in the upper layers above the mud diapirs and in host rocks exhibiting other geophysical characteristics. As the result of the formation of the gas hydrate, the free gas bearing strata are enclosed by the gas hydrate bearing strata. Due to the high pressure anomalies of the free gas bearing strata the fluid potential increases noticeably. It can then be concluded that the high fluid potential anomaly on the low fluid potential background may be caused by the presence of the free gas below the gas hydrate bearing strata.

Numerical modeling of water wave interaction with a soft mud bed

A vertical 2-D numerical model is presented for simulating the interaction between water waves and a soft mud bed. Taking into account nonlinear rheology, a semi-empirical rheological model is applied to this water-mud model, reflecting the combined visco-elasto-plastic properties of soft mud under such oscillatory external forces as water waves. In order to increase the resolution of the flow in the neighborhood of both sides of the inter-surface, a logarithmic grid in the vertical direction is employed for numerical treatment. Model verifications are given through comparisons between the calculated and the measured mud mass transport velocities as well as wave height changes.

Annual cycle of stratification and tidal fronts in the Bohai Sea: A model study

In general, competition between buoyancy mechanisms and mixing dynamics largely determines the water column structure in a shelf sea. A three dimensional baroclinic ocean model forced by surface heat fluxes and the 2.5 order Mellor-Yamada turbulence scheme is used to simulate the annual cycle of the temperature in the Bohai Sea. The difference between the sea surface temperature (SST) and sea bottom temperature (SBT) is used to examine the evolution of its vertical stratification. It is found that the water column is well-mixed from October to March and that the seasonal thermocline appears in April, peaks in July and then weakens afterwards, closely following the heat budget. In addition, the Loder parameter based on the topography and tidal current amplitude is also computed in order to examine tidal fronts in the BS, which are evident in summer months when the wind stirring mechanism is weak.

Evolution of freshwater plumes and salinity fronts in the northern Bay of Bengal

[1] The evolution of freshwater plumes and the associated salinity fronts in the northern Bay of Bengal ( henceforth the bay) is studied using rotated empirical orthogonal function (REOF) analysis and extended associate pattern analysis (EAPA). The results show that sea surface salinity distribution is featured by eastern-bay and western-bay plumes in the northern bay during different seasons. The western-bay plume begins in early July, peaks in late August, and then turns into a bay-shaped plume with the two plumes in either side of the bay, which peaks in late October. The southward extension of the western-bay plume can be explained by the southwestward geostrophic flow associated with the cyclonic gyre in the northern bay, which counters the northeastward Ekman drift driven by wind stress. The offshore expansion of the western-bay plume is induced by the offshore Ekman drift which also produces a salinity front near the east coast of India. The bay-shaped plume appears when the cyclonic gyre shifts westward and a weak anticyclonic gyre occupies the northeastern bay. As the season advances, the western part of the bay-shaped plume decays while the eastern part persists until the following June, which is believed to be associated with the anticyclonic gyre in the northern bay. The evolution of the plumes except the eastern part of the bay-shaped plume in fall can be partly explained by the seasonal variation of mass transport associated with the Sverdrup balance. The fact that the western-bay (eastern-bay) plume appears when surface freshwater flux in the northeastern bay increases ( decreases) dramatically suggests that the plumes are not produced directly by surface freshwater flux. River discharge seems to be the freshwater source for the plumes and has little to do with the evolution of the plumes.

Corrosion failure of marine steel in sea-mud containing sulfate reducing bacteria

The corrosion failure behavior of marine steel is affected by stress, which exists in offshore structures at sea-mud region. The sulfate reducing bacteria (SRB) in the sea-mud made the steel more sensitive to stress corrosion cracking (SCC) and weaken the corrosion fatigue endurance. In this paper, a kind of natural sea-mud containing SRB was collected. Both SCC tests by slow strain rate technique and corrosion fatigue tests were performed on a kind of selected steel in sea-mud with and without SRB at corrosion and cathodic potentials. After this, the electrochemical response of static and cyclic stress of the specimen with and without cracks in sea-mud was analyzed in order to explain the failure mechanism. Hydrogen permeation tests were also performed in the sea-mud at corrosion and cathodic potentials. It is concluded that the effect of SRB on environment sensitive fracture maybe explained as the consequences of the acceleration of SRB on corrosion rate and hydrogen entry into the metal.

Effect of sulfate-reducing bacteria on corrosion behavior of mild steel in sea mud

Microbiologically influenced corrosion (MIC) is very severe corrosion for constructions buried under sea mud environment. Therefore it is of great importance to carry out the investigation of the corrosion behavior of marine steel in sea mud. In this paper, the effect of sulfate-reducing bacteria (SRB) on corrosion behavior of mild steel in sea mud was studied by weight loss, dual-compartment cell, electronic probe microanalysis (EPMA), transmission electron microscopy (TEM).combined with energy dispersive X-ray analysis (EDX) and electrochemical impedance spectroscopy (EIS). The results showed that corrosion rate and galvanic current were influenced by the metabolic activity of SRB. In the environment of sea mud containing SRB, the original corrosion products, ferric (oxyhydr) oxide, transformed to iron sulfide. With the excess of the dissolved H2S, the composition of the protective layer formed of FeS transformed to FeS2 or other non-stoichiometric polysulphide, which changed the state of the former layer and accelerated the corrosion process.