Thermal-mechanical interface crack behaviour of a surface mount solder joint

The effect of thermal-mechanical loading on a surface mount assembly with interface cracks between the solder and the resistor and between the solder and the printed circuit board (PCB) was studied using a non-linear thermal finite element analysis. The thermal effect was taken as cooling from the solder eutectic temperature to room temperature. Mechanical loading at the ends of the PCB was also applied. The results showed that cooling had the effect of causing large residual shear displacement at the region near the interface cracks. The mechanical loading caused additional crack opening displacements. The analysis on the values of J-integral for the interface cracks showed that J-integral was approximately path independent, and that the effect of crack at the solder/PCB interface is much more serious than that between the component and solder.

A Linear Stability Analysis Of Large-Prandtl-Number Thermocapillary Liquid Bridges

A linear stability analysis is applied to determine the onset of oscillatory thermocapillary convection in cylindrical liquid bridges of large Prandtl numbers (4 <= Pr <= 50). We focus on the relationships between the critical Reynolds number Re-c, the azimuthal wave number m, the aspect ratio F and the Prandtl number Pr. A detailed Re-c-Pr stability diagram is given for liquid bridges with various Gamma. In the region of Pr > 1, which has been less studied previously and where Re, has been usually believed to decrease with the increase of Pr, we found Re-c exhibits an early increase for liquid bridges with Gamma around one. From the computed surface temperature gradient, it is concluded that the boundary layers developed at both solid ends of liquid bridges strengthen the stability of basic axisymmetric thermocapillary convection at large Prandtl number, and that the stability property of the basic flow is determined by the "effective" part of liquid bridge. (c) 2008 Published by Elsevier Ltd on behalf of COSPAR.

Elimination of loading reverberation in the split hopkinson torsional bar

The loading reverberation is a multiple wave effect on the specimen in the split Hopkinson torsional bar (SHTB). Its existence intensively destroys the microstructure pattern in the tested material and therefore, interferes with the study correlating the deformed microstructure to the macroscopic stress-strain response. This paper discusses the problem of the loading reverberation and its effects on the post-mortem observations in the SHTB experiment. The cause of the loading reverberation is illustrated by a stress wave analysis. The modification of the standard SHTB is introduced, which involves attaching two unloading bars at the two ends of the original main bar system and adopting a new loading head and a couple of specially designed clutches. The clutches are placed between the main bar system and the unloading bars in order to lead the secondary loading wave out of the main bar system and to cut off the connection in a timely manner. The loading head of the standard torsional bar was redesigned by using a tube-type loading device associated with a ratchet system to ensure the exclusion of the reflected wave. Thus, the secondary loading waves were wholly trapped in the two unloading bars. The wave recording results and the contrasting experiments for examining the post-mortem microstructure during shear banding both before and after the modification highly support the effectiveness of the modified version. The modified SHTB realizes a single wave pulse loading process and will become a useful tool for investigating the relation between the deformed microstructure and the macroscopic stress-strain response. It will play an important role especially in the study of the evolution of the microstructure during the shear banding process. (C) 1995 American Institute of Physics.

Transport Properties And Induced Voltage In The Structure Of Water-Filled Single-Walled Boron-Nitrogen Nanotubes

Density functional theory/molecular dynamics simulations were employed to give insights into the mechanism of voltage generation based on a water-filled single-walled boron-nitrogen nanotube (SWBNNT). Our calculations showed that (1) the transport properties of confined water in a SWBNNT are different from those of bulk water in view of configuration, the diffusion coefficient, the dipole orientation, and the density distribution, and (2) a voltage difference of several millivolts would generate between the two ends of a SWBNNT due to interactions between the water dipole chains and charge carriers in the tube. Therefore, this structure of a water-filled SWBNNT can be a promising candidate for a synthetic nanoscale power cell as well as a practical nanopower harvesting device.

Transport properties and induced voltage in the structure of water-filled single-walled boron-nitrogen nanotubes

Density functional theory/molecular dynamics simulations were employed to give insights into the mechanism of voltage generation based on a water-filled single-walled boron-nitrogen nanotube (SWBNNT). Our calculations showed that (1) the transport properties of confined water in a SWBNNT are different from those of bulk water in view of configuration the diffusion coefficient the dipole orientation and the density distribution and (2) a voltage difference of several millivolts would generate between the two ends of a SWBNNT due to interactions between the water dipole chains and charge carriers in the tube. Therefore this structure of a water-filled SWBNNT can be a promising candidate for a synthetic nanoscale power cell as well as a practical nanopower harvesting device.

Comparison of Yb-doped fiber laser with one-end and double-end pumping configuration

A high-power Ytterbium-doped fiber laser (YDFL) with homemade double clad fiber (DCF) is introduced in this paper. The output power characteristics of a linear cavity fiber laser have been studied theoretically by solving the rate equations and experimentally tested with single- and double-end-pumping configurations. When both ends of the fiber are pumped by two high-power laser diodes with a launched power of similar to 300 W each, a maximum CW output of 444 W is obtained with a slope efficiency of similar to 75%. (c) 2006 Elsevier Ltd. All rights reserved.

Secondary structures of mRNAs and splicing of introns in eukaryotes.

After analyzing the secondary structures of 68 exon-intron-exon and the corresponding exon-exon sequence segments, it is found that about 90% of 5' and 3' terminal bases G (splicing sites) of introns are situated in the loops of secondary structures or at the ends of stems near the loops, and most of "G" s in loops are closed to the ends of loops. Approximately 92% of the connecting sites of the adjoining exons also show the similar features. About 82% of the branch point "A" s are situated in loops or at the ends of stems near the loops. Splicing sites and branch points approach each other in space because of the folding.

Transcription rates of yeast genes are influenced by the distribution of introns

A comparative analysis on the intron sequence oligonucleotide usages in two sets of yeast genes with higher and lower transcription frequencies, respectively, has shown that the intron sequence structures of the two sets of genes are different. There are more potential binding sites for transcription factors in the introns of the genes with high transcription frequencies. So it is speculated that introns regulate the transcription of genes. But more evidences are needed to favor this speculation. The detailed comparative analyses on the distribution ( length and position) of introns and exons in the two sets of gene sequences also show that there is an obvious boundary between the lengths of the two sets of introns. There is no boundary between the lengths of the two sets of exons, although the means of their lengths are of discrepancy. The situation of the gene lengths ( length of intron and exon) is similar to exon lengths. As far as the relative position, the introns in two sets of genes all have a bias toward the 5' ends of genes. But as the actual position is considered, more introns in high transcription genes have a tendency to be located toward the 5' ends of genes, some even located at 5'-UTR. These results suggest that the gene transcription rates are related to the length of intron, but not to the lengths of exons and genes sequences. The positions of introns may also influence the transcription rates. The transcriptional regulation of introns may be correlative with the transcriptional regulation of the upstream of genes, or be its continuous action.

Seasonal patterns of sedimentation and their associations with benthic communities in Xiangxi Bay of the Three Gorges Reservoir, China

Sedimentation variables and benthic community data were collected at seven stations during four seasons in Xiangxi Bay of the Three Gorges Reservoir, China. Summer, the season of highest discharge into the reservoir, was characterized by the extreme sediment loading. The benthic macroinvertebrate community was dominated by oligochaetes across all seasons at most stations. In winter/spring, macroinvertebrate density and richness increased. Correspondence analysis showed that community structure differed among stations at the two ends of the bay in winter and among almost all stations in spring, However, no variable associated with sedimentation appeared to be associated with differences in the community.

Structure-function analysis of the inverted terminal repeats of the Sleeping Beauty transposon

Translocation of Sleeping Beauty (SB) transposon requires specific binding of SB transposase to inverted terminal repeats (ITRs) of about 230 bp at each end of the transposon, which is followed by a cut-and-paste transfer of the transposon into a target DNA sequence. The ITRs contain two imperfect direct repeats (DRs) of about 32 bp. The outer DRs are at the extreme ends of the transposon whereas the inner DRs are located inside the transposon, 165-166 bp from the outer DRs. Here we investigated the roles of the DR elements in transposition. Although there is a core transposase-binding sequence common to all of the DRs, additional adjacent sequences are required for transposition and these sequences vary in the different DRs. As a result, SB transposase binds less tightly to the outer DRs than to the inner DRs. Two DRs are required in each ITR for transposition but they are not interchangeable for efficient transposition. Each DR appears to have a distinctive role in transposition. The spacing and sequence between the DR elements in an ITR affect transposition rates, suggesting a constrained geometry is involved in the interactions of SB transposase molecules in order to achieve precise mobilization. Transposons are flanked by TA dinucleotide base-pairs that are important for excision; elimination of the TA motif on one side of the transposon significantly reduces transposition while loss of TAs on both flanks of the transposon abolishes transposition. These findings have led to the construction of a more advanced transposon that should be useful in gene transfer and insertional mutagenesis in vertebrates. (C) 2002 Elsevier Science Ltd. All rights reserved.

Sequence of genome segments 1, 2, and 3 of the grass carp reovirus (Genus Aquareovirus, family Reoviridae)

The genome segments 1, 2, and 3 of the grass carp reovirus (GCRV), a tentative species assigned to genus Aquareouirus, family Reouiridae, were sequenced. The respective segments 1, 2, and 3 were 3949, 3877, and 3702 nucleotides long. Conserved moths 5' (GUUAUUU) and 3' (UUCAUC) were found at the ends of each segment. Each segment contains a single ORF and the negative strand does not permit identification of consistent ORFs. Sequence analysis revealed that VP2 is the viral polymerase, while VPI might represent the viral guanyly/methyl transferase (involved in the capping process of RNA transcripts) and VP3 the NTPase/helicase (involved in the transcription and capping of viral RNAs), The highest amino acid identities (26-41%) were found with orthoreovirus proteins. Further genomic characterization should provide insight about the genetic relationships between GCRV, aquareoviruses, and orthoreoviruses, It should also permit to precise the taxonomic status of these different viruses. (C) 2000 Academic Press.

Efficiently producing single-walled carbon nanotube rings and investigation of their field emission properties

Single-walled carbon nanotube (SWNT) rings with a diameter of about 100 nm have been prepared by thermally decomposing hydrocarbon in a floating catalyst system. These rings appeared to consist mostly of SWNT toroids. High resolution transmission electron microscopy showed that these rings were composed of tens of SWNTs with a tightly packed arrangement. The production of SWNT rings was improved through optimizing various growth parameters, such as growth temperature, sublimation temperature of the catalyst, different gas flows and different catalyst components. The growth mechanism of the SWNT rings is discussed. In the field emission measurements we found that field emission from a halved ring is better than that from a whole SWNT ring, which contributed to the better emission from two opened ends of the nanotubes of the halved SWNT ring.

Recent progresses of SOI-based photonic devices - art. no. 60201R

SOI (Silicon on Insulator) based photonic devices, including stimulated emission from Si diode, RCE (Resonant Cavity Enhanced) photodiode with quantum structure, MOS (Metal Oxide Semiconductor) optical modulator with high frequency, SOI optical matrix switch and wavelength tunable filter are reviewed in the paper. The emphasis will be played on our recent results of SOI-based thermo-optic waveguide matrix switch with low insertion loss and fast response. A folding re-arrangeable non-blocking 4x4 matrix switch with total internal reflection (TIR) mirrors and a first blocking 16 x 16 matrix were fabricated on SOI wafer. The extinction ratio and the crosstalk are better. The insertion loss and the polarization dependent loss (PDL) at 1.55 mu m increase slightly with longer device length and more bend and intersecting waveguides. The insertion losses are expected to decrease 2-3 dB when anti-reflection films are added in the ends of the devices. The rise and fall times of the devices are 2.1 mu s and 2.3 mu s, respectively.

Synthesis, structure, and optical properties of a contorted (110)-oriented layered hybrid perovskite: C3H11SN3PbBr4

The < 110 >-oriented perovskite is very rare in the hybrid perovskites family. In this work, an unusual layered < 110 >-oriented hybrid perovskite, which is stabilized by a special organic ligand, 2-(aminoethyl)isothiourea, has been obtained. This ligand combines a primary amine and a formamidine on the two ends of one molecule. Introduction of the special ligand brings about contorted inorganic sheets in the hybrid perovskite structure. The optical properties of the new < 110 >-oriented perovskite were studied.

The complete mitochondrial genome sequence of the cutlassfish Trichiurus japonicus (Perciformes: Trichiuridae) : Genome characterization and phylogenetic considerations

Mitochondrial genome sequence and structure analysis has become a powerful tool for studying molecular evolution and phylogenetic relationships. To understand the systematic status of Trichiurus japonicus in suborder Scombroidei, we determined the complete mitochondrial genome (mitogenome) sequence using the long-polymerase chain reaction (long-PCR) and shotgun sequencing method. The entire mitogenome is 16,796 by in length and has three unusual features, including (1) the absence of tRNA(Pro) gene, (2) the possibly nonfunctional light-strand replication origin (O-L) showing a shorter loop in secondary structure and no conserved motif (5'-GCCGG-3'), (3) two sets of the tandem repeats at the 5' and 3' ends of the control region. The three features seem common for Trichiurus mitogenomes, as we have confirmed them in other three T. japonicus individuals and in T nanhaiensis. Phylogenetic analysis does not support the monophyly of Trichiuridae, which is against the morphological result. T. japonicus is most closely related to those species of family Scombridae; they in turn have a sister relationship with Perciformes members including suborders Acanthuroidei, Caproidei, Notothenioidei, Zoarcoidei, Trachinoidei, and some species of Labroidei, based on the current dataset of complete mitogenome. T japonicus together with T. brevis, T lepturus and Aphanopus carbo form a clade distinct from Lepidopus caudatus in terms of the complete Cyt b sequences. T. japonicus mitogenome, as the first discovered complete mitogenome of Trichiuridae, should provide important information on both genomics and phylogenetics of Trichiuridae. (C) 2009 Elsevier B.V. All rights reserved.