Thermal-mechanical interface crack behaviour of a surface mount solder joint

The effect of thermal-mechanical loading on a surface mount assembly with interface cracks between the solder and the resistor and between the solder and the printed circuit board (PCB) was studied using a non-linear thermal finite element analysis. The thermal effect was taken as cooling from the solder eutectic temperature to room temperature. Mechanical loading at the ends of the PCB was also applied. The results showed that cooling had the effect of causing large residual shear displacement at the region near the interface cracks. The mechanical loading caused additional crack opening displacements. The analysis on the values of J-integral for the interface cracks showed that J-integral was approximately path independent, and that the effect of crack at the solder/PCB interface is much more serious than that between the component and solder.

A Linear Stability Analysis Of Large-Prandtl-Number Thermocapillary Liquid Bridges

A linear stability analysis is applied to determine the onset of oscillatory thermocapillary convection in cylindrical liquid bridges of large Prandtl numbers (4 <= Pr <= 50). We focus on the relationships between the critical Reynolds number Re-c, the azimuthal wave number m, the aspect ratio F and the Prandtl number Pr. A detailed Re-c-Pr stability diagram is given for liquid bridges with various Gamma. In the region of Pr > 1, which has been less studied previously and where Re, has been usually believed to decrease with the increase of Pr, we found Re-c exhibits an early increase for liquid bridges with Gamma around one. From the computed surface temperature gradient, it is concluded that the boundary layers developed at both solid ends of liquid bridges strengthen the stability of basic axisymmetric thermocapillary convection at large Prandtl number, and that the stability property of the basic flow is determined by the "effective" part of liquid bridge. (c) 2008 Published by Elsevier Ltd on behalf of COSPAR.

Elimination of loading reverberation in the split hopkinson torsional bar

The loading reverberation is a multiple wave effect on the specimen in the split Hopkinson torsional bar (SHTB). Its existence intensively destroys the microstructure pattern in the tested material and therefore, interferes with the study correlating the deformed microstructure to the macroscopic stress-strain response. This paper discusses the problem of the loading reverberation and its effects on the post-mortem observations in the SHTB experiment. The cause of the loading reverberation is illustrated by a stress wave analysis. The modification of the standard SHTB is introduced, which involves attaching two unloading bars at the two ends of the original main bar system and adopting a new loading head and a couple of specially designed clutches. The clutches are placed between the main bar system and the unloading bars in order to lead the secondary loading wave out of the main bar system and to cut off the connection in a timely manner. The loading head of the standard torsional bar was redesigned by using a tube-type loading device associated with a ratchet system to ensure the exclusion of the reflected wave. Thus, the secondary loading waves were wholly trapped in the two unloading bars. The wave recording results and the contrasting experiments for examining the post-mortem microstructure during shear banding both before and after the modification highly support the effectiveness of the modified version. The modified SHTB realizes a single wave pulse loading process and will become a useful tool for investigating the relation between the deformed microstructure and the macroscopic stress-strain response. It will play an important role especially in the study of the evolution of the microstructure during the shear banding process. (C) 1995 American Institute of Physics.

Dynamic interaction of an elastic container with fluid

The vibration analysis of an elastic container with partially filled fluid was investigated in this paper. The container is made of a thin cylinder and two circular plates at the ends. The axis of the cylinder is in the horizontal direction. It is difficult to solve this problem because the complex system is not axially symmetric. The equations of motion for this system were derived. An incompressible and ideal fluid model is used in the present work. Solutions of the equations were obtained by the generalized variational method. The solution was expressed in a series of normalized generalized Fourier's functions. This series converged rapidly, and so its approximate solution was obtained with high precision. The agreement of the calculated values with the experimental result is good. It should be mentioned that with our method, the computer time is less than that with the finite-element method.

Subcooled Pool Boiling at Microgravity: Preliminary Ground-Based Experimental Results

A temperature-controlled pool boiling (TCPB) device was developed to perform pool boiling heat transfer studies at both normal gravity on Earth and microgravity in the drop tower Beijing and aboard a Chinese recovery satellite. Two platinum wires of 60 ?m in diameter were simultaneously used as heaters and thermometers. The lengths were 30 mm and 40 mm, respectively. The ends of wires were soldered with copper poles to provide low resistance paths for the electric current. The heater resistance, and thus the heater temperature, was kept constant by a feedback circuit similar to that used in constant-temperature hot-wire anemometry. The fluid was R113 at 0.1 Mpa and subcooled by 30 ?C nominally for all cases. The results of the experiments at normal gravity were presented. Four modes, namely single-phase convection, nucleate boiling, transition two-mode boiling, and film boiling were observed. A few data obtained from several preliminary experiments at microgravity in the drop tower Beijing were also presented. A slight increase of the heat flux was obtained.

Hydroelectric Voltage Generation Based On Water-Filled Single-Walled Carbon Nanotubes

A DFT/MD mutual iterative method was employed to give insights into the mechanism of voltage generation based on water-fitted single-walled carbon nanotubes (SWCNTs). Our calculations showed that a constant voltage difference of several mV would generate between the two ends of a carbon nanotube, due to interactions between the water dipole chains and charge carriers in the tube. Our work validates this structure of a water-fitted SWCNT as a promising candidate for a synthetic nanoscale power cell, as well as a practical nanopower harvesting device at the atomic level. 

Transport Properties And Induced Voltage In The Structure Of Water-Filled Single-Walled Boron-Nitrogen Nanotubes

Density functional theory/molecular dynamics simulations were employed to give insights into the mechanism of voltage generation based on a water-filled single-walled boron-nitrogen nanotube (SWBNNT). Our calculations showed that (1) the transport properties of confined water in a SWBNNT are different from those of bulk water in view of configuration, the diffusion coefficient, the dipole orientation, and the density distribution, and (2) a voltage difference of several millivolts would generate between the two ends of a SWBNNT due to interactions between the water dipole chains and charge carriers in the tube. Therefore, this structure of a water-filled SWBNNT can be a promising candidate for a synthetic nanoscale power cell as well as a practical nanopower harvesting device.

Transport properties and induced voltage in the structure of water-filled single-walled boron-nitrogen nanotubes

Density functional theory/molecular dynamics simulations were employed to give insights into the mechanism of voltage generation based on a water-filled single-walled boron-nitrogen nanotube (SWBNNT). Our calculations showed that (1) the transport properties of confined water in a SWBNNT are different from those of bulk water in view of configuration the diffusion coefficient the dipole orientation and the density distribution and (2) a voltage difference of several millivolts would generate between the two ends of a SWBNNT due to interactions between the water dipole chains and charge carriers in the tube. Therefore this structure of a water-filled SWBNNT can be a promising candidate for a synthetic nanoscale power cell as well as a practical nanopower harvesting device.

The ionic exclusion-enrichment in a hybrid micro-/nano-channel

An ionic exclusion-enrichment phenomenon has been found at the ends of a nano-channel when electric-driven fluid passes through a micro-/nano-hybrid channel [1-3]. In our experiments, the hybrid channels are fabricated with two poly-dimethysiloxane (PDMS) monoliths microchannels (100um X20um X 9mm) and a nanoporous polycarbonate nuclear track-etched (PCTE) membrane (with 50nm pores). The flows are driven under different electrical potential and the test liquids with different PH values are used. The ion depletion in the source channel is observed by the MicroPIV system. In addition, the numerical simulations about ionic exclusion-enrichment in the hybrid channel are carried out. Some results are as followed:

Smoothed Particle Hydrodynamics (SPH): an Overview and Recent Developments

Smoothed particle hydrodynamics (SPH) is a meshfree particle method based on Lagrangian formulation, and has been widely applied to different areas in engineering and science. This paper presents an overview on the SPH method and its recent developments, including (1) the need for meshfree particle methods, and advantages of SPH, (2) approximation schemes of the conventional SPH method and numerical techniques for deriving SPH formulations for partial differential equations such as the Navier-Stokes (N-S) equations, (3) the role of the smoothing kernel functions and a general approach to construct smoothing kernel functions, (4) kernel and particle consistency for the SPH method, and approaches for restoring particle consistency, (5) several important numerical aspects, and (6) some recent applications of SPH. The paper ends with some concluding remarks.

Temperature controlled filamentation in argon gas

Temperature controlled filamentation is experimentally demonstrated in a temperature gradient gas-filled tube. The proper position of the tube is heated by a furnace and two ends of the tube are cooled by air. The experimental results show that multiple filaments are shrunken into a single filament or no filament only by increasing the temperature at the beginning of the filament. This technique offers another degree of freedom of controlling the filamentation and opens a new way for intense monocycle pulse generation through gradient temperature in a noble gas.

千瓦级双包层光纤激光器冷却方案设计理论和实验研究

尽管双包层光纤激光器的散热性能好于传统的固体激光器的散热性能,光纤激光器中的热沉积仍然是限制提高其输出功率的重要因素.以双端抽运的400W双包层光纤激光器为实例,定量分析了光纤内的热沉积分布.根据所建立的散热模型,为了确保千瓦级双包层光纤激光器安全稳定的运行,抽运端附近的对流换热系数应大于2.8×10-2W·cm-2K-1.据此设计出高功率双包层光纤激光器抽运端冷却装置并成功应用在激光系统中,获得了千瓦级的激光输出.

Comparison of Yb-doped fiber laser with one-end and double-end pumping configuration

A high-power Ytterbium-doped fiber laser (YDFL) with homemade double clad fiber (DCF) is introduced in this paper. The output power characteristics of a linear cavity fiber laser have been studied theoretically by solving the rate equations and experimentally tested with single- and double-end-pumping configurations. When both ends of the fiber are pumped by two high-power laser diodes with a launched power of similar to 300 W each, a maximum CW output of 444 W is obtained with a slope efficiency of similar to 75%. (c) 2006 Elsevier Ltd. All rights reserved.

小麦春化相关基因的克隆及其功能分析

一． 小麦相关基因ver203F cDNA全序列克隆与功能分析 　　根据本实验室通过差异筛选技术克隆到的与春化相关的基因cDNA verc203的序列，设计PCR 5’端PCR引物，利用RACE（rapid amplification of cDNA ends）克隆策略，得到春化相关基因ver203基因的同源基因ver203F cDNA的3’端序列，长度为1,197bp。Northern分析表明ver203F全长约为1.5 kb，且其表达具有春化处理的特异性。根据3’RACE克隆的ver203F 3 ’端核苷酸序列设计了3’端PCR引物，利用5’RACE克隆到该基因的5’端片段，经DNASIS核酸分析软件分析将5’45RACE和3’RACE DNA序列拼接合并，得到ver203F全长cDNA，从TdT加尾5’末端到poly A全长为1,561 bp，5’端起始密码子ATG上游非编码区－1～－192共了192bp，终止密码子TGA到poly A的非编码区有253bp，cDNA编码区全长1,119 bp，推测编码373氨基酸残基。国际基因序列数据库检索表明该基因序列（GenBank/EMBL/DDBJ：AB012013）与大麦茉莉酸诱导基因有部分同源性。因上推测该基因在调控开花过程中可能参与茉莉酸介导的信号传导途径，ver203F作用的发挥可能需要其它蛋白的参与，或ver203F本身就是一个受体蛋白。 　　为了研究ver203F基因的功能，将通过3’RACE克隆到的ver203F 3’端序到分别构建正义和反义植物表达载体，通过花粉管通道法、农杆菌介导的叶圆片法以及农杆菌介导的真空转化法分别转化小麦、烟草和拟南芥菜。获得转基因植株后，PCR、DNA Dob Blot、Southern Blot分析以及GUS活性检测证明外源基因已整合到转基因植株中，并得到表达。在获得的小麦、烟草和拟南芥菜转基因植株中，它们开花时间都相应地推迟，表明正常植物体内该基因在控制营养生长向生殖生长的转变中起作用。ver203F可以影响小麦和拟南茶菜花序的发育，首先无论正义还是反义都使得花序的发育受到抑制，在小麦中表现为顶部小穗退化，在拟南芥菜中表现为顶花。其次在转化正义基因的转基因拟南芥菜中，观察到产生的顶花为对称的两朵或以对称的两朵顶花基部为生长点长出丛生花，这种对称花的麦型小麦小穗中小花的表型相类似，说明ver203F基因可能在小麦小花的发育过程中也起着重要作用。 二． 春化相关基因ver17在开花过程中功能的分析 以春化处理冬小麦（京冬1号）幼苗cDNA为材料，通过减法杂交与差异筛选得到春化相关cDNA克隆verc17。为了研究该基因的功能，以包含CaMV 35S启动子的pBI221为载体，将ver17cDNA片段分别从两个方向插入pBI221的BamH I－Sma I, Xba I－BamH I间，构建正义和反义表达质粒：p17S和p17X，通过花粉管通道法转化小麦。对T0和T1两代转基因小麦的观察发现，在转化反义基因p17X的转基因小麦首先表现为抽穗推迟，其次穗的顶部和基部小穗严重退化，另外还发现转化反义基因的小麦败育现象严重（主要是花粉败育），因此推测ver17基困能可具有以下几方面的特点：a．春化诱导型表达;b．促进植物开花;c．促进穗顶端和基部花的发育，减少其退化;d．影响雄蕊的发育。