Double-cladding Yb3+ fiber for free-space optical communication

The experiment result of Nd:YVO4 laser pumped by laser diode that was amplified by double-cladding Yb3+ fiber is reported. Stable mode-locking pulses are obtained at repetition rate of 320 MHz and the output power is 15 mW. When laser power is amplified by Yb3+- doped double-cladding fiber amplifier, its power can get to 600 mW. Based on these, experiment of double-frequency is carried out, and green laser with power of 4 mW is obtained. (c) 2007 Wiley Periodicals, Inc.

Design of Tapered Rib Spot-Size Converter with Double-Cladding Structure

A novel structure of spot-size converter is designed to allow low loss and large alignment tolerance between single-mode rib waveguide devices and fiber arrays theoretically. The spot-size converter consists of a tapered rib core region and a double-cladding region. Through optimizing parameters,an expanded mode field can be tightly confined in the inner cladding and thus radiation loss be reduced largely at the tapered region. The influence of refractive index and thickness of the inner cladding on coupling loss is analyzed in particular. A novel,easy method of fabricating tapered rib spot-size converter based on silicon-on-insulator material is proposed.

2W Yb-doped double-clad fiber superfluorescent source with 42 nm 3 dB bandwidth

The output spectrum of Yb-doped double-clad fiber superfluorescent source (SFS) is tailored by placing a broadband dichroic mirror in the pump end of conventional single-pass forward configuration, which constitutes double-pass forward configuration. The 3 dB bandwidth is increased from I I to 42 nm. A maximum output SFS power of 2.12 W and a slope efficiency of 43.2% are obtained. The double-clad fiber is 25 in and the pump power is adequate to saturate the fiber as far as the feedback-induced lasing appears. (c) 2004 Elsevier Ltd. All rights reserved.

110-W fiber laser with homemade double-clad fiber

A high-power ytterbium-doped fiber laser (YDFL) with homemade double-clad fiber (DCF) is introduced in this letter. The geometric parameter and laser characteristics of the fiber have been studied. With one-end-pumping scheme, pumped by a high-power laser diode with launching power of 280 W, a maximum continuous wave (CW) output of 110 W is obtained with an optical-to-optical efficiency of 40%.

A New Technique for Side Pumping of Double-Clad Fiber Lasers

We report a new technique, called SAP, for side pumping of double-clad, rare-earth-doped fiber lasers using fiber-coupled pump sources. The highest coupling efficiency can even exceed 92% in theory with this structure.

两根大芯双包层光纤激光器获得60W相干输出

报道了一个相位锁定的光纤激光器阵列获得60W的输出，同相模式输出时的斜率效率为37％。对于两种不同的纤芯距离都观测到稳定的高对比度干涉条纹。整个系统在高功率操作时，所用的空间滤波器没有观察到明显的热问题，这充分说明了采用这种方法能够进一步提高相干输出功率。

双包层光纤侧面耦合器

研究了一种侧面抽运双包层光纤的方法，从被剥除了外包层、端面为350μm×400μm的D型双包层光纤内包层上切下长度为3mm的一段柱体，并胶合在相同的双包层光纤内包层的侧面上，构成了柱体-光纤侧面耦合器。半导体激光器的抽运光从该柱体的一端入射并通过它耦合进入双包层光纤的内包层，实验测得耦合器最大耦合效率为85％。该方法适用于输出功率为数瓦的光纤激光器和放大器的侧面抽运。

微棱镜与双包层光纤侧面耦合效率的实验研究

对微棱镜与双包层光纤侧面耦合技术进行了研究。用光学胶把尺寸为1mm×1mm×1mm直角棱镜的直角面胶合在尺寸为330μm×170μm的内包层侧平面上，激光束以一定的角度从微棱镜的另一直角面入射并通过它耦合进入双包层光纤的内包层，实验测得耦合效率为86％。该方法可用于双包层光纤的侧面抽运。

高功率脉冲双包层光纤激光器的新进展

对高功率脉冲双包层光纤激光器的国内外研究进展进行评述，通过建立了小信号瞬态增益模型，对脉冲激光信号经过双包层光纤放大后的波形进行了数值模拟。分析了基于MOPA方式脉冲双包层光纤激光器的几个问题，报道了中科院上海光机所采用振荡-放大（MOPA）方法获得133．8W平均功率脉冲放大输出的实验结果。

两根掺镱大芯双包层光纤激光器获得113W同相输出功率

利用一个自成像共焦腔和一个空间滤波器实现了两掺Yb大芯光纤激光器的位相锁定。观测到稳定的具有高对比度的干涉条纹。相干条纹的对比度为59%，而非相干时对比度为6%。中心条纹的宽度与理论计算结果吻合得很好。对同相模式而言，位相锁定激光器阵列输出达到113W，对应的斜率效率为38.5%。

采用国产双包层光纤的声光调Q激光器

实验报道采用我国自行设计的大模场掺镱双包层光纤，利用简单声光调Q装置，成功实现调Q运转；在1－50kHz调制频率下获得了百纳秒的调Q脉冲，其输出光束质量因子大约为2。当重复频率为1kHz时，获得了脉冲宽度为132ns，能量0.93mJ。同时实验中观察到的调Q脉冲常出现一点锁模现象，针对这一现象进行了讨论。