Effects of constructed wetland system on the removal of dibutyl phthalate (DBP)

Phthalic acid esters (PAEs) have become widely diffused in the environment via the manufacturing process. Numerous experiments have shown that the bioaccumulation of PAEs occurred in the aquatic and terrestrial food chain; meanwhile, it was found that some of PAEs were considered as potential carcinogens, teratogens and mutagens. In this research, two vertical/reverse-vertical flow constructed wetland systems were set up to study its removal efficiency of dibutyl, phthalate (DBP) pollution. The results showed that the constructed wetland system could remove DBP effectively, and the removal rates reached nearly 100%. Substrate microorganism and enzymatic activities probably played key roles during DBP removal, and the removal of DBP probably mainly took place in the upper layer of chamber A in the constructed wetland systems. (C) 2007 Elsevier GmbH. All rights reserved.

Removal of dibutyl phthalate by a staged, vertical-flow constructed wetland

Two sets of small scale systems of staged, vertical-flow constructed wetlands (VFCW) were operated in a greenhouse to study the purification of dibutyl phthalate (DBP) in admeasured water. Each system consisted of two chambers in which water flowed downward in chamber I and then upward in chamber 2. The systems were intermittently fed with wastewater under a hydraulic load of 420 mm(.)d(-1). The measured influent concentrations of DBP in the experimental system were 9.84 mg(.)l(-1), while the other system was used as a control and received no DBP. Effluent concentrations of the treated system averaged 5.82 mug(.)l(-1) and were far below the Chinese DBP discharge standard of less than or equal to0.2 mg(.)l(-1). These results indicate the potential purification capacity of this new kind of constructed wetland in removing DBP from a polluted water body.

Enzymatic activities in constructed wetlands and di-n-butyl phthalate (DBP) biodegradation

The bioaccumulation of phthalate acid esters (PAEs) from industrial products and their mutagenic action has been suggested to be a potential threat to human health. The effects of the most frequently identified PAE, Di-n-butyl phthalate (DBP), and its biodegradation, were examined by comparison of two small scale plots (SSP) of integrated vertical-flow constructed wetlands. The influent DBP concentration was 9.84 mg l(-1) in the treatment plot and the control plot received no DBP. Soil enzymatic activities of dehydrogenase, catalase, protease, phosphatase, urease, cellulase, beta-glucosidase, were measured in the two SSP after DBP application for 1 month and 2 months, and 1 month after the final application. Both treatment and control had significantly higher enzyme activity in the surface soil than in the subsurface soil (P < 0.001) and greater enzyme activity in the down-flow chamber than in the up-flow chamber (P < 0.05). In the constructed wetlands, DBP enhanced the activities of dehydrogenase, catalase, protease, phosphatase and inhibited the activities of urease, cellulase and beta-glucosidase. However, urease, cellulase, beta-glucosidase activities were restored 1 month following the final DBP addition. Degradation of DBP was greater in the surface soil and was reduced in sterile soil, indicating that this process may be mediated by aerobic microorgansims. DBP degradation fitted a first-order model, and the kinetic equation showed that the rate constant was 0.50 and 0.17 d(-1), the half-life was 1.39 and 4.02 d, and the r(2) was 0.99 and 0.98, in surface and subsurface soil, respectively. These results indicate that constructed wetlands are able to biodegrade organic PA-Es such as DBP. (c) 2005 Elsevier Ltd. All rights reserved.

Determination of phthalate acid esters plasticizers in plastic by ultrasonic solvent extraction combined with solid-phase microextraction using calix[4]arene fiber

Ultrasonic solvent extraction combined with solid-phase microextraction (SPME) with calix[4]arene/hydroxy-terminated silicone (C[4]/OHTSO) oil coated fiber was used to extract phthalate acid esters (PAEs) plasticizers in plastic, such as blood bags, transfusion tubing, food packaging bag, and mineral water bottle for analysis by gas chromatography (GC). Both extraction parameters (i.e. extraction time, extraction temperature, ionic strength) and conditions of the thermal desorption in a GC injector were optimized by analysis of eight phthalates. The fiber shows wonderful sensitivity and selectivity to the tested compounds. Owing to its high thermal stability (380 degreesC), the carryover effect that often encountered when using conventional fibers can be reduced by appropriately enhancing the injector temperature. The method showed linear response over two to four orders of magnitude with correlation coefficients (r) better than 0.996, and limits of detection (LOD) ranged between 0.006 and 0.084 mug l(-1). The relative standard deviation values obtained were less than or equal to 10%. bis-2-Ethylhexyl phthalate (DEHP) was the sole analyte detected in these plastics and recoveries were in the ranges 95.5-101.4% in all the samples. (C) 2004 Elsevier B.V. All rights reserved.

Synthesis and spectroscopic study of mesoporous aluminum methylphosphonate foam templated by dibutyl methylphosphonate

New types of templates and novel interactive mechanisms between template and framework are very important for creating porous materials. In this work, by using neutral dibutyl methylphosphonate as a template, an inorganic-organic hybrid mesoporous material, aluminum methylphosphonate, was prepared. The as-synthesized material was studied by P-31 magnetic angle spinning nuclear magnetic resonance (MAS NMR), Al-27 MAS NMR, C-13 CP/MAS, FT-IR spectroscopy, thermogravimetry (TG), differential thermal analysis (DTA), and transmission electron microscopy. After thermal treatment at 673 K and 10 mmHg for 2 h, hybrid mesoporous foam was obtained. The transformation process was investigated by FT-IR. TG-DTA results indicate that the methyl group bonded to the framework keeps intact up to 792 K under air and 823 K under nitrogen. The characterization results from nitrogen gas adsorption-desorption measurements show that the BET surface area and the Barrett-Joyner-Halenda desorption cumulative pore volume of the foam are 90 m(2) g(-1) and 0.32 cm(3) g(-1) respectively. (C) 2003 Elsevier Inc. All rights reserved.

Electroluminescent devices based on monohexadecyl phthalate terbium

Electroluminescent devices with PVK film doped with monohexadecyl phthalate terbium and PBD were fabricated. The device structure of glass substrate/ITO/PPV/PVK:Tb(MHP)(3):PBD/Alq(3)/Al was employed. The emissive layer was formed by a spin-casting technique. The EL cells exhibited characteristic emission of terbium ions with a maximum luminance of 74 cd/m(2) at 18 V. (C) 1998 Elsevier Science S.A. All rights reserved.

Synthesis, luminescence, energy transfer and Langmuir-Blodgett films of amphiphilic complexes of rare earths with monooctadecyl phthalate

Three new amphiphilic rare earth complexes with only two organic long chains Ln (MOP)(2)Cl (MOP=monooctadecyl phthalate, Ln=Eu, Tb, Gd) were synthesized and characterized by elemental analysis. The complexes (Eu, Tb) showed good luminescence property with long fluorescence lifetime, whereas the intensity and lifetime of Tb complex are greater than those of Eu complex, By measuring the triplet energy levels of ligand based on energy transfer mechanism, above phenomena have been well explained. The Langmuir films of the complexes on the air/water interface were also studied and the results show that all of them have good film-forming property.

ANTHROPOGENIC ORGANIC CONTAMINANTS IN WATER AND SURFACE SEDIMENTS OF LARGE SHALLOW EUTROPHIC CHAOHU LAKE, CHINA

To characterize the contamination of anthropogenic organic contaminants in the aquatic environment of Chaohu Lake, China, 7 samples for both water and surface sediment were collected in the lake. Organic contaminants were extracted by solid phase extraction (SPE) and Soxhlet extraction from the water and surface sediment samples, respectively, and then analyzed by GC-MS. One hundred and twenty kinds of organic chemicals were detected in these samples including phenol, benzene series, benzaldehydes, ethanol, polycyclic aromatic hydrocarbons (PAHs), sulfur compounds, alcoholic halides, amines, ketones, esters, alkenes and alkanes. Among them, 13 kinds of chemicals were identified as priority pollutants listed by the U.S. Environmental Protection Agency (EPA), such as phthalate esters (PAEs) and PAHs. Besides, the concentrations of 19 of PAEs and PAHs including, priority pollutants identified were also determined. Bis(2-ethylhexyl)phthalate, the predominant component of the analyzed pollutants, was in the range from 72.34 ng g(-1) DW to 613.71 ng g(-1) DW, 14.80 ng L-1 to 47.05 ng L-1 in sediment and water, respectively. The results indicated that the northwest part of the lake was heavily polluted by domestic and industrial wastewater.

Distribution of 25 semi-volatile organic compounds of two urban lakes in Wuhan, China

In this study, the levels of 25 semi-volatile organic compounds (SVOCs) were measured in samples of water, suspended particulate matter (SPM) and sediment from two urban lakes in Wuhan, China. The total concentrations of 25 SVOCs varied from 529.4 to 2168.9 ng/L, 120.7 to 22543.7 ng/g dry weight and 1577.3 to 61579.6 ng/g dry wt. in water, SPM and sediment, respectively. The concentration of SVOCs in SPM was 9-10 times higher than that in water, and the concentration of SVOCs in sediment 1.5-2 times higher than that in SPM. The level of total SVOC25 in the samples from Moshuihu Lake was higher than that in Yuehu Lake. Among the 25 SVOCs, phthalate compounds were on the highest level in all observed samples ranging between 441.9-1831.2 ng/L, 116.3-17566.8 ng/g, dry wt. and 6432.8-48177.6 ng/g dry wt. in water, SPM and sediment, respectively. Bis(2-ethylhexyl)phthalate, the predominant component of the analyzed pollutants, was in the range from 246.7 to 537.5 ng/l, 51.2 to 15540.0 ng/g dry wt. and 468.2 to 45010.3 ng/g dry wt. in water, SPM and sediment, respectively. The content of PAHs, dinitrotoluene and isophoton in sediment was higher than that in water and SPM at most of the locations. The possible sources of the pollutants and their inter-relation with human activities were discussed.

Water solubility enhancement of phthalates by cetyltrimethylammonium bromide and beta-cyclodextrin

Water solubility enhancements of six phthalates (five aliphatic phthalates and one phenyl phthalate) by cetyltrimethylammonium bromide (CTAB) and beta-cyclodextrin (beta-CD) were studied at 25 degreesC. The solubilities of these plithalates are remarkably enhanced by CTAB solutions above the critical micelle concentration (cmc). Only marginal enhancement of phthalate solubility was observed in solutions containing CTAB below its cmc and beta-CD at low concentrations (less than 5 mM). The solubility enhancements of the plithalates are proportional to the added amount of CTAB and beta-CD. Partition coefficients of the plithalates between monomeric CTAB surfactant and water (K-MN) and between CTAB micelle and water K-MC) were estimated from the experimental data. The mechanisms of solubility enhancements by CTAB and beta-CD were discussed. A log-linear equation was proposed and evaluated for the solubilization by CTAB below cmc, while the previously proposed linear partitioning model was questioned. The structures of the complexes formed between plithalates and beta-CD were proposed, and the formation constants were estimated. The values of log K-MC, log K-MN, and log Kbeta-CD of the plithalates were found to correlate linearly with the log K-OW of plithalates, with the exception of the solid phenyl phthalate.

Homogeneous Epitaxial Growth of N,N '-di(n-butyl)quinacridone Thin Films on Ag(110)

The structural evolution of the ordered N-N' dibutyl-substituted quinacridone (QA4C) multilayers (3 MLs) has been monitored in situ and in real time at various substrate temperatures using low energy electron diffraction (LEED) during organic molecular beam epitaxy (MBE). Experimental results of LEED patterns clearly reveal that the structure of the multilayer strongly depends on the substrate temperature. Multilayer growth can be achieved at the substrate temperatures below 300 K, while at the higher temperatures we can only get one ordered monolayer of QA4C. Two kinds of structures, the commensurate and incommensurate one, often coexist in the QA4C multilayer. With a method of the two-step substrate temperatures, the incommensurate one can be suppressed, and the commensurate, on the other hand, more similar to the (001) plane of the QA4C bulk crystal, prevails with the layer of QA4C increasing to 3 MLs. The two structures in the multilayers are compressed slightly in comparison to the original ones in the first monolayer.

Template-assisted syntheses of two novel porous zirconium methylphosphonates

Two porous zirconium methylphosphonates (designated as ZMPmi and ZMPme respectively) were synthesized by using dibutyl methylphosphonate (DBMP) as a template. Two efficient post-synthetic treatments were developed to remove the incorporated template without destroying the hybrid structures. The materials were characterized by SEM, EPMA, TG, DTA, FTIR, and NMR. Specific surface area and porosity were evaluated by BET, alpha(s)-plots and DFT methods based on N-2 adsorption-desorption isotherms. The specific surface areas of ZMPmi and ZMPme are determined to be 279 and 403 m(2) g(-1) and the maxima of pore size distributions are at 0.7 and 1.3 nm respectively. (c) 2005 Elsevier Inc. All rights reserved.

Mercury selective electrochemical sensor based on a double armed crown ether as ionophore

PVC based membranes of a double armed crown ether, N, N'-dibenzyl, 1,4,10,13-tetraoxa-7, 16-diaza cyclooctadecane (I) as ionophore with sodium tetra phenyl borate (NaTPB) as anion excluder and with many plasticizing solvent mediators have been prepared and used for Hg(II) ion determination. The membrane with DBBP (dibutyl butyl phosphonate ) as plasticizer with various ingredients in the ratio PVC: I: NaTPB: DBBP (150: 12: 2: 100) shows the best results in terms of working concentration range (3.1x10-5-1.0x10-tM) with a Nernstian slope (29.0′0.5 mV/decade of activity). The electrode works in the pH range 2.1-4.5. The response time of the sensor is 15s and it can be used for about 4 months in aqueous as well as in non-aqueous medium. It has good stability and reproducibility. The potentiometric selectivity coefficient values for mono-, di-, and trivalent cations are tabulated. The sensor is highly selective for Hg2+ in the presence of normal interferents like cadmium, silver, sodium and iron.