Dynamic recrystallization induced by plastic deformation at high strain rate in a Monel alloy

An investigation has been made into the plastic deformation behavior of a Monel alloy deformed at high strain rate of 10(5) s(-1) by split Hopkinson bar. The results reveal that there are some equiaxed grains with an average size of 150 nm in diameter in the center of the shear bands, suggesting that this microstructure characteristics be developed by dynamic recrystallization, arising from the deformation and the rapid temperature rise in the band. Analysis shows that the plastic strain rate and the mobile dislocation density play a key role in the new crystallized grain formation and growth. Based on grain boundary energy change and diffusion mechanism, the grain growth kinetics is developed for plastic deformation at a high strain rate.

Strain-Induced Grain Refinement of Cobalt During Surface Mechanical Attrition Treatment

The microstructural evolution during surface mechanical attrition treatment of cobalt (a mixture of hexagonal close packed (hep) and face-centered cubic (fcc) phases) was investigated. In order to reveal the mechanism of grain refinement and strain accommodation. The microstructure was systematically characterized by both cross-sectional and planar-view transmission electron microscopy. In the hcp phase, the process of grain refinement. Accompanied by an increase in strain imposed in the surface layer. Involved: (1) the onset of 110 111 deformation twinning, (2) the operation of (1 120) 110 1 0} prismatic and (1 120) (000 1) basal slip, leading to the formation of low-angle dislocation boundaries, and (3) the successive subdivision of grains to a finer and finer scale. Ressulting in the formation of highly misoriented nanocrystalline grains. Moreover. The formation of nanocrystalliies at the grain boundary and triple junction was also observed to occur concurrently with straining. By contrast. The fec phase accommodated strain in a sequence as follows: (1) slip of dislocations by forming intersecting planar arrays of dislocations, (2) {1 1 1} deformation twinning, and (3) the gamma(fcc) --> epsilon(hcp) martensitic phase transformation. The mechanism of grain refinement was interpreted in terms of the structural subdivision of grains together with dynamic recrystallization occurring in the hep phase and the gamma --> E: martensitic transformation in the fcc phase as well.

Preparation and characterization of As-cast and hot-rolled Mg-3Al-0.5Mn-0.5Zn-1MM alloy

Mg-3Al-0.5Mn-0.5Zn-1MM alloy was prepared by metal mould casting method. The as-cast ingot was homogenized and then hot-rolled at 673 K with total thickness reduction of 65%. Microstructure and mechanical properties of the as-cast and hot-rolled samples were investigated. The results showed that the as-cast sample mainly consisted of alpha-Mg, beta-Mg17Al12, Al10Ce2Mn7, and Al11RE3 (RE = La and Ce) phases. The average grain size of the sample homogenized at 673 K was about 240 gm, and it was greatly refined to about 7 mu m by dynamic recrystallization for the hot-rolled sample.

山东莒南地区韧性剪切带的变形特征与形成演化

Ju Nan of Shandong province is located at southwest of Sulu UHP (ultrahigh-pressure) metamorphic terrane. It is composed of gneiss, paragneiss, eclogites, ultramafic rocks, marble and quartzite. A large ductile shear zone extends east-west has been found at the Zhubian, The south of Junan county. The Zhubian ductile shear zone is composed of high srain rock and mylonites. The mylonites fall into 3 types: Initial gneiss mylonite, mylonite and altramylonit.obvious lineation of penetration,foliation,S-Cfabrics,porphyroclasts,folds,irregularundulatory,extinction,subgrain boundary, dynamic recrystallization microstructure, core-mantle structure and are common in the ductile shear zone. Based on field work and microstructural analyse, a conclution is arrived: The ductile shear zone is an approximately SE trending faults. The Zhubian ductile shear zone formed at Ep ―Hb facies conditions which could be proved by deformaed and metamorphosed mineral aggregates, Deformation behavior, Ternary-feldspar geothermometry and so on. Zircon MC―ICP―MS U-Pb analysis is performed on the mylonite and have an average age ―835.9±13.9Ma, it’s the primary rocks formed age. The Zhubian ductile shear zone maybe formed at 224-242Ma.

Shear localization and recrystallization in dynamic deformation of 8090 Al-Li alloy

The microstructural evolution in localized shear deformation was investigated in an 8090 Al-Li alloy by split Hopkinson pressure bar (strain rate of approximately 10(3) s(-1)) at ambient temperature and 77 K. The alloy was tested in the peak-, over-, under-, and natural-aged conditions, that provide a wide range of microstructural parameters and mechanical properties. Two types of localized shear bands were distinguished by optical microscopy: the deformed shear band and the white-etching shear band. They form at different stages of deformation during localization. There are critical strains for the occurrence of deformed and white-etching localized shear deformation, at the imposed strain rate. Observations by transmission electron microscopy reveal that the white-etching bands contain fine equiaxed grains; it is proposed that they are the result of recrystallization occurring during localization. The deformed-type bands are observed after testing at 77 K in all heat treatment conditions, but they are not as well defined as those developed at ambient temperature. Cracking often occurs along the localized shear at ambient temperature. The decrement in temperature is favorable for the nucleation, growth and coalescence of the microcracks along the shear bands, inducing fracture.

Evolutionary Conservation of Dazl Genomic Organization and its Continuous and Dynamic Distribution Throughout Germline Development in Gynogenetic Gibel Carp

To investigate germline development and germ cell specification, we identified a Dazl homolog (CagDazl) from gynogenetic gibel carp (Carassius auratus gibelio). Its cDNA sequence and BAC clone sequence analyses revealed the genomic organization conservation and conserved synteny of the Dazl family members and their neighborhood genes among vertebrates, especially in fish. Moreover, a polyclonal antibody specific to CagDazl was produced and used to examine its expression and distribution throughout germline development at protein level. Firstly, ovary-specific expression pattern of CagDazl was confirmed in adult tissues by RT-PCR and Western blot. In addition, in situ hybridization and immunofluorescence localization demonstrated its specific expression in germ cells, and both its transcript and protein were localized to germ plasm. Then, co-localization of CagDazl and mitochondrial cloud was found, confirming that CagDazl transcript and its protein are germ plasm component and move via METRO pathway during oogenesis. Furthermore, the CagDazl is abundant and continuous throughout germline development and germ cell specification including primordial germ cell (PGC) formation, oogonium differentiation, oocyte development, and embryogenesis, and the dynamic distribution occurs at different development stages. The data suggest that maternal CagDazl might play an important role in gibel carp PGC formation. Therefore, CagDazl is a useful and specific marker for tracing germ plasm and germ cell development in the gynogenetic gibel carp. In addition, in comparison with previous studies in sexual reproduction species, the continuous and dynamic distribution of CagDazl protein in the germ plasm throughout the life cycle seems to have significant implication in sex evolution of vertebrates. J. Exp. Zool. (Mol. Deu. Euol.) 312B:855-871, 2009. (C) 2009 Wiley-Liss, Inc.

Dynamic SIF of interface crack between two dissimilar viscoelastic bodies under impact loading

In this paper, the transient dynamic stress intensity factor (SIF) is determined for an interface crack between two dissimilar half-infinite isotropic viscoelastic bodies under impact loading. An anti-plane step loading is assumed to act suddenly on the surface of interface crack of finite length. The stress field incurred near the crack tip is analyzed. The integral transformation method and singular integral equation approach are used to get the solution. By virtue of the integral transformation method, the viscoelastic mixed boundary problem is reduced to a set of dual integral equations of crack open displacement function in the transformation domain. The dual integral equations can be further transformed into the first kind of Cauchy-type singular integral equation (SIE) by introduction of crack dislocation density function. A piecewise continuous function approach is adopted to get the numerical solution of SIE. Finally, numerical inverse integral transformation is performed and the dynamic SIF in transformation domain is recovered to that in time domain. The dynamic SIF during a small time-interval is evaluated, and the effects of the viscoelastic material parameters on dynamic SIF are analyzed.

Evolution of thermoplastic shear localization and related microstructures in Awl/SiCp composites under dynamic compression

The localized shear deformation in the 2024 and 2124 Al matrix composites reinforced with SiC particles was investigated with a split Hopkinson pressure bar (SHPB) at a strain rate of about 2.0x10(3) s(-1). The results showed that the occurrence of localized shear deformation is sensitive to the size of SiC particles. It was found that the critical strain, at which the shear localization occurs, strongly depends on the size and volume fraction of SiC particles. The smaller the particle size, the lower the critical strain required for the shear localization. TEM examinations revealed that Al/SiCp interfaces are the main sources of dislocations. The dislocation density near the interface was found to be high and it decreases with the distance from the particles. The Al matrix in shear bands was highly deformed and severely elongated at low angle boundaries. The Al/SiCp interfaces, particularly the sharp corners of SiC particles, provide the sites for microcrack initiation. Eventual fracture is caused by the growth and coalescence of microcracks along the shear bands. It is proposed that the distortion free equiaxed grains with low dislocation density observed in the center of shear band result from recrystallization during dynamic deformation.

A Diode-Side-Pumped Dynamic Fundamental Mode Nd:YAG Laser

A fundamental mode Nd YAG laser is experimentally demonstrated with a stagger pumped laser module and a special resonator. The rod is pumped symmetrically by staggered bar modules. A dynamic fundamental mode is achieved with the special resonator under different pump levels. A maximal continuous wave output of 61 W (M-2 = 1.4) is achieved with a single rod. An average output of 47 W, pulse width of 54 ns, pulse energy of 4.7 mJ and peak power of 87 kW are obtained under the Q-switched operation of 10 kHz.

Coalition and distribution in fuzzy dynamic supply chain systems

In this paper, two models of coalition and income's distribution in FSCS (fuzzy supply chain systems) are proposed based on the fuzzy set theory and fuzzy cooperative game theory. The fuzzy dynamic coalition choice's recursive equations are constructed in terms of sup-t composition of fuzzy relations, where t is a triangular norm. The existence of the fuzzy relations in FSCS is also proved. On the other hand, the approaches to ascertain the fuzzy coalition through the choice's recursive equations and distribute the fuzzy income in FSCS by the fuzzy Shapley values are also given. These models are discussed in two parts: the fuzzy dynamic coalition choice of different units in FSCS; the fuzzy income's distribution model among different participators in the same coalition. Furthermore, numerical examples are given aiming at illustrating these models., and the results show that these models are feasible and validity in FSCS.

Information geometry theory of high-dimension space and application for speaker independent continuous digit speech recognition

In the light of descriptive geometry and notions in set theory, this paper re-defines the basic elements in space such as curve and surface and so on, presents some fundamental notions with respect to the point cover based on the High-dimension space (HDS) point covering theory, finally takes points from mapping part of speech signals to HDS, so as to analyze distribution information of these speech points in HDS, and various geometric covering objects for speech points and their relationship. Besides, this paper also proposes a new algorithm for speaker independent continuous digit speech recognition based on the HDS point dynamic searching theory without end-points detection and segmentation. First from the different digit syllables in real continuous digit speech, we establish the covering area in feature space for continuous speech. During recognition, we make use of the point covering dynamic searching theory in HDS to do recognition, and then get the satisfying recognized results. At last, compared to HMM (Hidden Markov models)-based method, from the development trend of the comparing results, as sample amount increasing, the difference of recognition rate between two methods will decrease slowly, while sample amount approaching to be very large, two recognition rates all close to 100% little by little. As seen from the results, the recognition rate of HDS point covering method is higher than that of in HMM (Hidden Markov models) based method, because, the point covering describes the morphological distribution for speech in HDS, whereas HMM-based method is only a probability distribution, whose accuracy is certainly inferior to point covering.

Research on continuous speech recognition with small vocabulary based on biomimetic pattern recognition

Based on biomimetic pattern recognition theory, we proposed a novel speaker-independent continuous speech keyword-spotting algorithm. Without endpoint detection and division, we can get the minimum distance curve between continuous speech samples and every keyword-training net through the dynamic searching to the feature-extracted continuous speech. Then we can count the number of the keywords by investigating the vale-value and the numbers of the vales in the curve. Experiments of small vocabulary continuous speech with various speaking rate have got good recognition results and proved the validity of the algorithm.

A speaker-independent continuous speech recognition system using biomimetic pattern recognition

In speaker-independent speech recognition, the disadvantage of the most diffused technology (HMMs, or Hidden Markov models) is not only the need of many more training samples, but also long train time requirement. This paper describes the use of Biomimetic pattern recognition (BPR) in recognizing some mandarin continuous speech in a speaker-independent manner. A speech database was developed for the course of study. The vocabulary of the database consists of 15 Chinese dish's names, the length of each name is 4 Chinese words. Neural networks (NNs) based on Multi-weight neuron (MWN) model are used to train and recognize the speech sounds. The number of MWN was investigated to achieve the optimal performance of the NNs-based BPR. This system, which is based on BPR and can carry out real time recognition reaches a recognition rate of 98.14% for the first option and 99.81% for the first two options to the persons from different provinces of China speaking common Chinese speech. Experiments were also carried on to evaluate Continuous density hidden Markov models (CDHMM), Dynamic time warping (DTW) and BPR for speech recognition. The Experiment results show that BPR outperforms CDHMM and DTW especially in the cases of samples of a finite size.

Dynamic power management approaches based on neural network

Dynamic Power Management (DPM) is a technique to reduce power consumption of electronic system. by selectively shutting down idle components. In this article we try to introduce back propagation network and radial basis network into the research of the system-level policies. We proposed two PAY policies-Back propagation Power Management (BPPM) and Radial Basis Function Power management (RBFPM) which are based on Artificial Neural Networks (ANN). Our experiments show that the two power management policies greatly lowered the system-level power consumption and have higher performance than traditional Power Management(PM) techniques-BPPM is 1.09-competitive and RBFPM is 1.08-competitive vs. 1.79,145,1.18-competitive separately for traditional timeout PM, adaptive predictive PM and stochastic PM.

dynamic evolutions based on ontologies

With the continuous changes in application requirements of the enterprises, Web resources must be updated, so do the underlying ontologies that are associated with the Web resources. In the situation, it is very challenging for ontological engineers to specify the changes of ontologies, keep their consistencies and achieve semantic query of Web resources based on the evolving ontologies. We propose a construct called Prioritized Knowledge Base (PKB) based on SHOQ(D) description logic, and discuss some properties of PKB.PKB can be used for describing the evolutions and updates of ontologies with conflicting information. Furthermore, we develop some algorithms for checking conflict rules and performing semantic query based on PKB.