Boiling heat transfer enhancement by using micro-pin-finned surface for electronics cooling

For efficiently cooling electronic components with high heat flux, experiments were conducted to study the flow boiling heat transfer performance of FC-72 over square silicon chips with the dimensions of 10 × 10 × 0.5 mm3. Four kinds of micro-pin-fins with the dimensions of 30 × 60, 30 × 120, 50 × 60, 50 × 120 μm2 (thickness, t × height, h) were fabricated on the chip surfaces by the dry etching technique for enhancing boiling heat transfer. A smooth surface was also tested for comparison. The experiments were made at three different fluid velocities (0.5, 1 and 2 m/s) and three different liquid subcoolings (15, 25 and 35 K). The results were compared with the previous published data of pool boiling. All micro-pin-fined surfaces show a considerable heat transfer enhancement compared with a smooth surface. Flow boiling can remarkably decrease wall superheat compared with pool boiling. At the velocities lower than 1 m/s, the micro-pin-finned surfaces show a sharp increase in heat flux with increasing wall superheat. For all surfaces, the maximum allowable heat flux, qmax, for the normal operation of LSI chips increases with fluid velocity and subcooling. For all micro-pin-finned surfaces, the wall temperature at the critical heat flux (CHF) is less than the upper limit for the reliable operation of LSI chips, 85◦C. The largest value of qmax can reach nearly 148 W/cm2 for micro-pin-finned chips with the fin height of 120 μm at the fluid velocity of 2 m/s and the liquid subcooling of 35 K. The perspectives for the boiling heat transfer experiment of the prospective micro-pin-finned sur- faces, which has been planned to be made in the Drop Tower Beijing/NMLC in the future, are also presented.

Balitora nantingensis (Teleostei : Balitoridae), a new hillstream loach from Salween drainage in Yunnan, Southwestern China

A new species of hillstream loach genus Balitora Gray is discovered from Nanting River drainage, which drains to Salween, Yongde County, Yunnan, China. Balitora nantingensis can be distinguished from B. lancangjiangensis by a triangle-like blotch in nape absent vs. present; area from halfway of pelvicfin ray to anus covered by scales vs. no scales in this area; the first pectoral ray thickened vs. not; posterior end of pelvic-fin surpasses middle point from posterior end of pelvic-fin base to anal-fin origin vs. the end from posterior extremity of pelvic-fins to anus; fewer lateral line scales, 59-64 vs. 66-70; slightly longer head, SL 4.2-5.1 (4.6) times of HL vs. 5.0-5.9 (5.4); slightly larger eyes, HL 4.0-6.4 (5. 1) times of eye diameter vs. 5.5-7.5 (6.3). Balitora nantingensis can be distinguished from B. burmanica by body rounded vs. slender in dorsal view; pointed snout vs. blunt in dorsal view; a deeper body, body depth 12.5-16.9% of SL vs. 10-12%; a deeper caudal-peduncle, length of caudal-peduncle 2.0-2.8 times of its depth vs. 3.0-4.2; a shorter caudal-peduncle, 14.3-15.6% of SL vs. 16-21%; the average ratio of body width at pelvic-fin origin and distance between inner pelvic-fin base 2.0 vs. 3.4; body width 1.1-1.5 times of body depth vs. 1.5-1.6; posterior end of pelvic-fin almost one or slight more than one eye diameter from anus vs. closet to anus; outside rays of pelvic-fin extend more posteriorly than inside rays and make posterior outline of fin acclivitous and straight vs. the outside ones almost equal to the inside ones and make the fin slightly convex.

Two new species and a new record of the genus Sinogastromyzon (Teleostei: Balitoridae) from Yunnan, China

Two new species and a new record of Sinogastromyzon are described from Lixianjiang River of Yunnan province, China. Sinogastromyzon lixianjiangensis, new species, can be distinguished from its congeners by the following characters: pectoral fin with XIII-XIV, 15-17 rays; pelvic fin with X-XI, 10-12 rays; 60-65 lateral-line scales; no scales on the dorsum of paired fins or the region between axilla of pectoral fin and pelvic-fin origin; tip of pelvic fin close to anus; tip of anal fin close to caudal-fin base; anal-fin origin nearer to the caudal-fin base than to the posterior pelvic-fin base; anus nearer to anal-fin origin than to the posterior pelvic-fin base; dorsal side of the body with 9-11 black blotches. Sinogastromyzon macrostoma, new species can be distinguished from its congeners by the following characters: pectoral fin with XII-XIV, 12-15 rays; pelvic fin with VII-IX, 11-13 rays; 48-56 lateral-line scales; mouth extremely big, slightly arched; no scales on the dorsum of paired fins or the region between axilla of pectoral fin and pelvic-fin origin; tip of pelvic fin far beyond anus; tip of anal fin far from caudal-fin base; anal-fin origin about midway between the posterior pelvic-fin base and caudal-fin base; anus nearer to posterior pelvic-fin base than to anal-fin origin; dorsal side of the body uniformly gray, without regular blotches in formalin preserved specimen. Sinogastromyzon cf. multiocellum is firstly recorded in China.

两种鳜病毒的共感染现象及引起感染细胞的超微变化

借助细胞培养和电镜技术,揭示了鳜球形病毒(Siniperca chuatsi spherical virus,SCSV)与鳜弹状病毒(Siniperca chuatsi rhabdovirus,SCRV)在草鱼鳍细胞(Grass carp fins,GCF)中共感染的现象。在筛选到敏感鱼类细胞系和建立了 鳜病毒体外增殖系统的基础上,取息典型病毒感染出血症的鳜组织,制备组织悬液,接种到GCF细胞中传代培养, 在攻毒后间隔不同时间收集细胞,对攻毒细胞的超薄切片进行电镜观察。揭示两种形态的鳜病毒可在同一个GCF

Onychostoma virgulatum, a new species of cyprinid fish (Pisces: Teleostei) from southern Anhui Province, South China

Onychostoma virgulatum, new species, is described from the Qiupu River, a tributary on the Southern bank of the lower Yangtze River at Shitai County, southern Anhui Province, South China. It shares with O. fusiforme and O. meridionale the presence of a longitudinal dark brown stripe extending along the lateral line, a character separating them from all other congeners of the moderate-mouth group diagnosed by having a slightly arched or nearly transverse mouth opening (with the extremities slightly curved posteriorly), its width being equal to or slightly less than the width of head at this same point, and a short postlabial groove extending along half of the length of the lateral margin of the lower jaw. Onychostoma virgulatum differs from both in the presence of two pairs of barbels in adults, from O. fusiforme in the body depth, caudal-peduncle depth, and position of pelvic and anal fins, and from O. meridionale in the structure of the last simple dorsal-fin ray.

Bibarba bibarba: A new genus and species of Cobitinae (Pisces : Cypriniformes : Cobitidae) from Guangxi Province (China)

A new genus of Cobitinae, Bibarba gen. n., and a new species, B. bibarba sp. n., were discovered and are described for the Chengjiang River, a tributary of the Hongshuihe River in Guangxi Province of southern China. This river region is characterized by a Karst landscape, and the river that is inhabited by the new genus is a slowly moving stream with arenaceous and cobblestone beds. The new genus resembles Cobitis Linnaeus, 1758 (subfamily Cobitinae) in the shape and pigmentation pattern of their body, the absence of scales on their head, and the presence of a suborbital spine, but differs from it by a single Lamina circularis on the third pectoral fin ray instead of on the base of the second pectoral fin ray; two pairs of barbels (one rostral pair and one maxillo-mandibular pair) instead of three pairs of barbels (one rostral pair, one maxillary pair, and one maxillo-mandibular pair); a relatively thick and short suborbital spine with a strong medio-lateral process instead of a suborbital spine without or with a weakly formed medio-lateral process as in Cobitis; and the lack of a black stripe extending from the occiput through the eye to the insertion of the rostral barbel. The first two characters have not been reported in any other genus of the subfamily Cobitinae. A morphometric character analysis based on PCA reveals differences between B. bibarba and C. sinensis in body size, barbel length, interorbital width, pectoral fin length in males, and the position of the dorsal and ventral fins. Type specimens of the new species are kept in the Freshwater Fishes Museum of the Institute of Hydrobiology at the Chinese Academy of Sciences in Wuhan, Hubei Province. (c) 2007 Elsevier GmbH. All rights reserved.

Spawning areas and early development of long spiky-head carp (Luciobrama macrocephalus) in the Yangtze River and Pearl River, China

The spawning areas and early development of long spiky-head carp, Luciobrama macrocephalus (Lacepede), an endemic fish species in China, were investigated in the Yangtze River and Pearl River of central and southeastern China between 1961 and 1993. The potamodromous fish migrated upstream to spawn between May and July as the floodwater began to rise. The water-hardened eggs drifted down the river, and the embryos and larvae developed in the course of drifting. The spawning areas of the fish were widely found in the upper and middle main channels and large tributaries. Two large dams (Gezhouba dam and Danjiangkou dam) did not significantly impact on the reproduction of the fish. Fifty stages of the early development from one cell to the juvenile with fully formed fins were observed and characterized pictorially. The larvae of long spiky-head carp could be distinguished from the larvae of other co-occurring species by counting the number of somites and comparing the proportion of sizes of eye to otic capsule.

Experimental Study on the Subthreshold Swing of Silicon Nanowire Transistors

SOI based wrap-gate silicon nanowire FETs are fabricated through electron beam lithography and wet etching. Dry thermal oxidation is used to further reduce the patterned fins cross section and transfer them into nanowires. Silicon nanowire FETs with different nanowire widths varying from 60 nm to 200 nm are fabricated and the number of the nanowires contained in a channel is also varied. The on-current (I-ON) and off-current (I-OFF) of the fabricated silicon nanowire FET are 0.59 mu A and 0.19 nA respectively. The subthreshold swing (SS) and the drain induced barrier lowering are 580 mV/dec and 149 mVN respectively due to the 30 nm thick gate oxide and 1015 cm(-3) lightly doped silicon nanowire channel. The nanowire width dependence of SS is shown and attributed to the fact that the side-gate parts of a wrap gate play a more effectual role as the nanowires in a channel get narrower. It seems the nanowire number in a channel has no effect on SS because the side-gate parts fill in the space between two adjacent nanowires.

FLOW STRUCTURES IN THREE-DIMENSIONAL FISH-LIKE SWIMMING

The swimming of a fish-like body is numerical simulated. The wake structures consist of a series of hairpin-like vortices braided together. The caudal fins generated vorticity interacts constructively with the body-bounded vorticity.

Low conductance injection tubes for storage cell targets

The effect of adding internal fins to the injection tube of a storage cell target filled with a polarized atomic beam source has been studied. The tube conductance and the atomic beam intensity at the exit of the injection tube have been measured, observing an unexpectedly large beam loss. Simulations of the atomic beam reproduce the observed attenuation only when the non-zero azimuthal component of the atom's velocity is taken into account.

三种海水经济鱼类早期发育生物学的研究

海水经济鱼类的养殖在我国已经形成第四次海水养殖浪潮，经济效益显著，有力地推动了我国海水养殖的产业结构调整和可持续发展。然而在海水养殖发展过程中也存在着诸多问题，尤其是早期发育阶段的高死亡率，严重制约了我国海水养殖产业的稳定和健康发展。 海水鱼类养殖的关键为高质量，高存活率苗种的生产和培育，由于鱼类种类繁多，生物多样性丰富，对应实际的繁育技术，尤其是新品种的开发，必须要做出相应的调整。这就要求我们必须对每一种鱼类早期发育有所了解，并将形态和组织上的数据用于指导生产。 本文通过显微观察和组织学研究，主要描述和研究了我国北方三种重要的海水经济鱼类(条斑星鲽、杂交鲆、条石鲷)的早期发育生物学，并结合实际生产进一步阐明关键期的产生原因，机理以及采用相应的对策。具体结果如下： 1.条斑星鲽：作为冷温性鲆鲽鱼类，条斑星鲽早期发育过程的特征主要有： ① 条斑星鲽受精卵无油球，卵子呈半浮性；不同步卵裂现象提前，发生在第三次卵裂；卵裂期裂球大小差异大。孵化过程较长，在水温8 ± 0.3℃，盐度33的条件下，经9 d孵化。条斑星鲽胚胎发育的不同时期对温度的敏感性不同，其中原肠期对温度比较敏感。 ②在8-10℃，盐度33的条件下，8-9 dph开口摄食。且开口时，其吻前端出现有一点状黑褐色素，构成了条斑星鲽仔鱼“开口期”的重要标志。卵黄囊于消失。在后期仔鱼末期，背鳍和臀鳍上形成特有的黑褐色条斑带。 ③杯状细胞首先出现在咽腔后部和食道前段，胃腺和幽门盲囊出现于29 dph，变态期始于30dph。在条斑星鲽早期发育过程中，观察到其直肠粘膜层细胞质出现大量嗜伊红颗粒，为仔鱼肠道上皮吸收的蛋白质。 ④首先淋巴化的免疫器官是头肾，然后是胸腺和脾脏，这与大部分硬骨鱼类不同。条斑星鲽除头肾和脾脏外，胸腺实质也形成MMCs。其中以脾脏形成MMCs最为丰富，形态多样。 2. 杂交鲆：为同属的牙鲆和夏鲆间的远缘杂交种，其发育过程的特点为： ① 在温度为15.4～16.0℃，杂交鲆胚胎从受精到孵化所需的时间为76 h左右，胚孔关闭前期，胚胎先出现视囊及克氏囊，而后形成体节。孵出前胚体在卵膜内环绕不到1周。 ② 孵化后消失。杂交鲆群体变态间隔长(34-60 dph)，且变态高峰期出现的冠状幼鳍不明显(与母本牙鲆相比)，数量为7-8根。 ③组织学观察发现，其消化系统中胃腺出现较晚，且胃腺发育过程缓慢(与母本牙鲆相比)。甲状腺滤泡增生不明显，颜色较浅，数量较少。杂交鲆在早期发育过程中，并没有出现鳔原基。 3. 条石鲷作为岩礁性的暖水性鱼类，早期发育过程也较为特殊，包括外形以及内部的器官结构。主要特点有： ① 受精卵：受精卵卵黄上具有龟裂结构，为鱼卵的分类特征之一。 ② 初孵仔鱼：初孵仔鱼背鳍膜上的黑色素，从体背面向背鳍膜边缘移动，到3dph仔鱼基本消失，此为本种仔鱼发育所特有的特点。 ③ 后期仔鱼和稚鱼：肠道肌肉层加厚明显，仔稚鱼胃肠排空率急剧上升，死亡率增加，通过改善常规的投饵方式部分解决了这个死亡高峰的问题。在幼鱼初期，牙齿融合为骨喙，为石鲷科鱼类的特征。 ④胸腺上皮分泌细胞：类似的现象同样在虹鳟鱼中发现，但是虹鳟鱼胸腺上皮分泌细胞不如条石鲷的丰富，同样也不如条石鲷的排列整齐，而是零星分布在胸腺上皮与咽腔接触的表面。除了正常的造血器官—脾脏和头肾外，肝脏、胰腺和鳔等多种组织等也出现MMCs，此现象在硬骨鱼类不多见，一般发生在软骨鱼类。

Methanol steam reforming in a compact plate-fin reformer for fuel-cell systems

A compact plate-fin reformer (PFR) consisting of closely spaced plate-fins, in which endothermic and exothermic reactions take place in alternate chambers, has been studied. In the PFR, which was based on a plate-fin heat exchanger, catalytic combustion of the reforming gas, as a simulation of the fuel cell anode off gas (AOG), supplied the necessary heat for the reforming reaction. One reforming chamber, which was for hydrogen production, was integrated with two vaporization chambers and two combustion chambers to constitute a single unit of PFR. The PFR is very compact, easy to be placed and scaled up. The effect of the ratio of H2O/CH3OH on the performance of the PFR has been investigated, and temperature distributions in different chambers were studied. Besides, the stationary behavior of the PFR was also investigated. Heat transfer of the reformer was enhanced by internal plate-fins as well as by external catalytic combustion, which offer both high methanol conversion ratio and low CO concentration. In addition, the fully integrated reformer exhibited good test stability. Based on the PFR, a scale-up reformer was designed and operated continuously for 1000 h, with high methanol conversion ratio and low CO concentration. (c) 2004 International Association for Hydrogen Energy. Published by Elsevier Ltd. All rights reserved.