Predictions for Partial-Dislocation-Mediated Processes in Nanocrystalline Ni by Generalized Planar Fault Energy Curves: An Experimental Evaluation

Generalized planar fault energy (GPFE) curves have been used to predict partial-dislocation-mediated processes in nanocrystalline materials, but their validity has not been evaluated experimentally. We report experimental observations of a large quantity of both stacking faults and twins in nc Ni deformed at relatively low stresses in a tensile test. The experimental findings indicate that the GPFE curves can reasonably explain the formation of stacking faults, but they alone were not able to adequately predict the propensity of deformation twinning.

An anisotropic elastic-plastic constitutive model for single and polycrystalline metals. II—Experiments and predictions concerning thin-walled tubular OFHC copper

Predictions based on an anisotropic elastic-plastic constitutive model proposed in the first part of this paper are compared with the experimental stress and strain data on OHFC copper under first torsion to about 13% and partial unloading, and then tension-torsion to about 10% along eight different loading paths. This paper also describes the deformation and stress of the thin-walled tubular specimen under finite deformation, the numerical implementation of the model, and the detailed procedure for determining the material parameters in the model. Finally, the model is extended to a general representation of the multiple directors, and the elastic-viscoplastic extension of the constitutive model is considered.

First principles based predictions of the toughness of a metal/oxide interface

We describe a first-principles-based strategy to predict the macroscopic toughness of a gamma-Ni(Al)/alpha-Al2O3 interface. Density functional theory calculations are used to ascertain energy changes upon displacing the two materials adjacent to the interface, with relaxation conducted over all atoms located within adjoining rows. Traction/displacernent curves are obtained from derivatives of the energy. Calculations are performed in mode I (opening), mode II (shear) and at a phase angle of 45 degrees. The shear calculations are conducted for displacements along < 110 > and < 112 > of the Ni lattice. A generalized interface potential function is used to characterize the results. Initial fitting to both the shear and normal stress results is required to calibrate the unknowns. Thereafter, consistency is established by using the potential to predict other traction quantities. The potential is incorporated as a traction/displacement function within a cohesive zone model and used to predict the steady-state toughness of the interface. For this purpose, the plasticity of the Ni alloy must be known, including the plasticity length scale. Measurements obtained for a gamma-Ni superalloy are used and the toughness predicted over the full range of mode mixity. Additional results for a range of alloys are used to demonstrate the influences of yield strength and length scale.

First principles based predictions of the toughness of a metal/oxide interface

We describe a first-principles-based strategy to predict the macroscopic toughness of a gamma-Ni(Al)/alpha-Al2O3 interface. Density functional theory calculations are used to ascertain energy changes upon displacing the two materials adjacent to the interface, with relaxation conducted over all atoms located within adjoining rows. Traction/displacernent curves are obtained from derivatives of the energy. Calculations are performed in mode I (opening), mode II (shear) and at a phase angle of 45 degrees. The shear calculations are conducted for displacements along < 110 > and < 112 > of the Ni lattice. A generalized interface potential function is used to characterize the results. Initial fitting to both the shear and normal stress results is required to calibrate the unknowns. Thereafter, consistency is established by using the potential to predict other traction quantities. The potential is incorporated as a traction/displacement function within a cohesive zone model and used to predict the steady-state toughness of the interface. For this purpose, the plasticity of the Ni alloy must be known, including the plasticity length scale. Measurements obtained for a gamma-Ni superalloy are used and the toughness predicted over the full range of mode mixity. Additional results for a range of alloys are used to demonstrate the influences of yield strength and length scale.

alpha-decay half-lives of superheavy nuclei and general predictions

The generalized liquid drop model (GLDM) and the cluster model have been employed to calculate the alpha-decay half-lives of superheavy nuclei (SHN) using the experimental alpha-decay Q values. The results of the cluster model are slightly poorer than those from the GLDM if experimental Q values are used. The prediction powers of these two models with theoretical Q values from Audi et al. (Q(Audi)) and Muntian et al. (Q(M)) have been tested to find that the cluster model with Q(Audi) and Q(M) could provide reliable results for Z > 112 but the GLDM with Q(Audi) for Z <= 112. The half-lives of some still unknown nuclei are predicted by these two models and these results may be useful for future experimental assignment and identification.

Stratigraphic Model Predictions of Geoacoustic Properties

Geoacoustic properties of the seabed have a controlling role in the propagation and reverberation of sound in shallow-water environments. Several techniques are available to quantify the important properties but are usually unable to adequately sample the region of interest. In this paper, we explore the potential for obtaining geotechnical properties from a process-based stratigraphic model. Grain-size predictions from the stratigraphic model are combined with two acoustic models to estimate sound speed with distance across the New Jersey continental shelf and with depth below the seabed. Model predictions are compared to two independent sets of data: 1) Surficial sound speeds obtained through direct measurement using in situ compressional wave probes, and 2) sound speed as a function of depth obtained through inversion of seabed reflection measurements. In water depths less than 100 m, the model predictions produce a trend of decreasing grain-size and sound speed with increasing water depth as similarly observed in the measured surficial data. In water depths between 100 and 130 m, the model predictions exhibit an increase in sound speed that was not observed in the measured surficial data. A closer comparison indicates that the grain-sizes predicted for the surficial sediments are generally too small producing sound speeds that are too slow. The predicted sound speeds also tend to be too slow for sediments 0.5-20 m below the seabed in water depths greater than 100 m. However, in water depths less than 100 m, the sound speeds between 0.5-20-m subbottom depth are generally too fast. There are several reasons for the discrepancies including the stratigraphic model was limited to two dimensions, the model was unable to simulate biologic processes responsible for the high sound-speed shell material common in the model area, and incomplete geological records necessary to accurately predict grain-size

STUDIES ON MORPHOLOGY OF SOLUTION-CAST FILMS OF IPP/APP BLENDS

Morphologies of solution-cast films of iPP/aPP blends have been studied by means of electron microscopy and X-ray scattering techniques. Microscopic observation showed that solution-cast film of iPP consists of two kinds of structural regions, cross-hatched and lath-liked structures. The addition of small amount of aPP (less than or equal to 30%) into iPP did not change iPP's characteristic crystallization behavior. It is noticed that when the content of aPP in its blend was over 80%, iPP formed a very loosely woven-like network composed of very long lamellae with wide-angle lamellar branchings. The X-ray data showed that aPP did not cocrystallize with iPP.

iPP／aPP共混物溶液浇铸薄膜的形态结构研究

用透射电子显微镜和Ｘ射线衍射等方法研究了等规立构聚丙烯（ｉＰＰ）和无规立构聚丙烯（ａＰＰ）共混物溶液浇铸膜的形态结构，结果表明，ａＰＰ的加入对ｉＰＰ的形态结构有很大的影响。

iPP/aPP共混物薄膜的形态结构研究

聚烯烃共混物中,最常见的和已商品化的是 iPP 与三元乙丙橡胶(EPDM)的共混物。人们一直用 EPDM 或乙丙无规共聚物(EPR)作为增韧剂加入到 iPP 中以提高其冲击强度。实验证明,橡胶的加入会导致 iPP 形态结构的变化。aPP 是一种非晶聚合物,它有类似像胶的性能,据报道,aPP 与 iPP 在熔体是相容的,aPP 的加入对 iPP 形态结构有很大影响。本文用 TEM 和 X-射线衍射等方法研究了 iPP/aPP 共混物薄膜的形态结构。

iPP／aPP共混物薄膜的形态结构研究

ｉＰＰ／ａＰＰ共混物薄膜的形态结构研究陈晔，杨德才（中国科学院长春应用化学研究所高分子物理开放实验室，长春１３００２２）聚烯烃共混物中，最常见的和已商品化的是ｉＰＰ与三元乙丙橡胶（ＥＰＤＭ）的共混物。人们一直用ＥＰＤＭ或乙丙无规共聚物（ＥＰＲ）作为增...