Mass resolved MPI spectra of methyl iodide in the 430-490 nm region

The mass resolved multiphoton ionization (MPI) spectra of methyl iodide were obtained in the 430-490 nm region using a time-of-flight (TOF) mass spectrometer. They have the same vibrational structure, which testifies that the fragment species, in the wavelength region under study, are from the photodissociation of multiphoton ionized molecular parent ions. Some features in the spectra are identified as three-photon excitations to 6p and 7s Rydberg states of methyl iodide. Two new vibrational structures of some Rydberg states are observed. The mechanism of ionization and dissociation is also discussed. (C) 2001 Elsevier Science B.V. All rights reserved.

Phase transition in polyamide-66/montmorillonite nanocomposites on annealing

The crystalline-phase transition in polyamide-66/montmorillonite nanocomposites before melting was investigated by in situ X-ray diffraction and is reported for the first time in this work. The phase-transition temperature in the nanocomposites was 170 degreesC, 20 degreesC lower than that in polyamide-66. The lower phase-transition temperature of the nanocomposites could be attributed to the gamma-phase-favorable environment caused by silicate layers. Meanwhile, the addition of silicate layers changed the crystal structure of the polyamide-66 matrix and influenced the phase-transition behavior.

Microstructure analysis of nylon 66 by WAXD and SAXS

The analysis of the small angle X-ray scattering (SAXS) data was based upon particle characteristic function, one-dimensional electron-density correlation function and particle distribution function. The microstructure of nylon 66 with different degrees of crystallinity was studied by means of X-ray scattering method. The radius of gyration R-g, the Porod radius R-p, the thickness of crystalline region L-c the thickness of non-crystalline region L-n, the thickness of interphase region d(tr), the long period L, the semiaxises of particles (a, a, b), the distribution of the particle sizes and the scattering invariant were calculated. The results indicate that there was a significant interphase region between the crystalline region and the non-crystalline region. and its content (W-t,W-x) should not be neglected in comparison with that of crystalline region W-c,W-x. The morphology of nylon 66 prepared by isothermal crystallization at a high temperature was mainly a lamellar structure, while the spherical crystals dominated in the quenched sample. The size of the particles in the quenched sample was smaller than that of those in the isothermally crystallized sample. and the distribution of the particle sizes in the isothermally crystallized sample was wider.

Melting crystallization behavior of nylon 66

Analysis of isothermal and nonisothermal crystallization kinetics of nylon 66 was carried out using differential scanning calorimetry (DSC). The commonly used Avrami equation and that modified by Jeziorny were used, respectively, to fit the primary stage of isothermal and nonisothermal crystallizations of nylon 66. In the isothermal crystallization process, mechanisms of spherulitic nucleation and growth were discussed. The lateral and folding surface free energies determined from the Lauritzen-Hoffman treatment are sigma = 9.77 erg/cm(2) and sigma (e) = 155.48 erg/cm(2), respectively; and the work of chain folding is q = 33.14 kJ/mol. The nonisothermal crystallization kinetics of nylon 66 was analyzed by using the Mo method combined with the Avrami and Ozawa equations. The average Avrami exponent (n) over bar was determined to be 3.45. The activation energies (DeltaE) were determined to be -485.45 kJ/mol and -331.27 kJ/mol, respectively, for the isothermal and nonisothermal crystallization processes by the Arrhenius and the Kissinger methods.

PA1010/66共聚物红外光谱研究

用红外光谱法研究了Pa1010/66共聚物氢键含量、N-H键伸缩振动力常数分布与组成的关系，发现66盐重量含量为40%时氢键含量最低，N-H伸缩振动力常数分布最宽，解释了PA1010/66共聚物热力学、结晶、机械等性能随组成改变而变化的原因.

尼龙1010/6及尼龙1010/66基本物理性能与组成的关系

尼龙1010/6 和尼龙1010/66 的基本物理性能随着组成的改变而改变,尼龙1010 含量高时,共聚物密度大于计算值;含量低时,共聚物密度小于计算值.尼龙1010 含量20%左右时,共聚物具有较大吸水率

Crystallization and melting behavior of nylon 66 poly(ether imide) blends

Isothermal crystallization and melting behavior of nylon 66 and its blends with poly(ether imide) (PEI) were investigated by differential scanning calorimetry. Crystallization kinetics such as overall rate constant Z and index n were calculated according to Avrami approach. Crystallization in the blend was retarded with respect to that of pure nylon 66 by incorporation of PEI with high glass transition temperature (T-g). The lowest growth rate of the spherulites was observed in the blends containing 10 and 15 wt% fraction of PEI. A transition temperature where positively birefringent spherulites disappear and negative birefringent spherulites develop was measured by thermal analysis. The transition temperature increased with content of PEI in the blends. A suitable range of isothermally crystallization temperatures, 238.5-246 degrees C, is suggested For determining the equilibrium melting points by means of Hoffman-Weeks approach.

Tremolite-reinforced nylon 66 composites: Mechanical and rheological properties

The reinforcement effect of an acicular inorganic filler, tremolite, on nylon 66 was studied. The mechanical properties of tremolite-filled nylon 66 composites and the effect of the filler particle size on them were obtained. The dynamic mechanical properties and rheological properties of the composites were measured. Two treatments, silane and unsaturated polyester, were used to improve the interface between tremolite and the nylon matrix. The morphologies of the composites were investigated using SEM. (C) 1998 John Wiley & Sons, Inc.

PA1010/66共聚物的松弛行为

研究了PA1010/66共聚物在液氮温度与Tm之间的松弛行为与组成的关系发现不同的松弛温度及损耗因子随共聚物组成的改变而变化的趋势不同随66含量增加，Tγ总趋势下降，Tβ总趋势增加，Tα先下降后增加；tanδ(γ)·tan-1δ(α)和tanδtan-1δ(α)先下降后增加，tanδ(α)先增大后减小。66占50％时，Tγ、Tβ极大，Tα最小；tanδ(γ)tanδ(β)、tanδ(β)·tan－1δ(α)最小，tanδ(α)最大.

辐射交联型PA－66机械物理性能研究

本文讨论了进口与国产ＰＡ—６６经钴源辐射交联后，对机械物理性能产生的影响。发现适量经辐射的ＰＡ—６６球压硬度、拉伸强度、Ｉｚｏｄ冲击强度都有较大幅度提高，并在１００，０００Ｇｙ剂量对达最大值，而断裂伸长率在１００，０００Ｇｙ剂量以下变化不大。国产ＰＡ—６６辐射后在乙二醇中，在２５０℃时，２小时不起层，性能变化不大，可替代进口材料。

MORPHOLOGY AND DYNAMIC-MECHANICAL PROPERTIES OF NYLON 66/POLY(ETHER IMIDE) BLENDS

The morphology and dynamic mechanical properties of blends of poly(ether imide) (PEI) and nylon 66 over the full composition range have been investigated. Torque changes during mixing were also measured. Lower torque values than those calculated by the log-additivity rule were obtained, resulting from the slip at the interface due to low interaction between the components. The particle size of the dispersed phase and morphology of the blends were examined by scanning electron microscopy. The composition of each phase was calculated. The blends of PEI and nylon 66 showed phase-separated structures with small spherical domains of 0.3 similar to 0.7 mu m. The glass transition temperatures (T(g)s) of the blends were shifted inward, compared with those of the homopolymers, which implied that the blends were partially miscible over a range of compositions. T-g1, corresponding to PEI-rich phase, was less affected by composition than T-g2, corresponding to nylon 66-rich phase. This indicated that the fraction of PEI mixed into nylon 66-rich phase increased with decreasing PEI content and that nylon 66 was rarely mixed into the PEI-rich phase. The effect of composition on the secondary relaxations was examined. Both T-beta, corresponding to the motion of amide groups in nylon 66, and T-gamma, corresponding to that of ether groups in PEI, were shifted to higher temperature, probably because of the formation of intermolecular interactions between the components.

硅灰石填充尼龙66的力学性能

硅灰石填充尼龙６６的力学性能王雪芹，李滨耀（中国科学院长春应用化学研究所长春１３００２２）关键词硅灰石，尼龙６６，填充改性，力学性能硅灰石是一种工业矿物，具有完整的短纤维针状结构，在塑料的填充改性中，能够与石棉、滑石、云母等相媲美，在欧美占无机填料市...

[Cp_2ErCl(THF)]_2的晶体结构

本文报导了(Cp_2ErCl(THF)]_2的晶体结构,晶体属单斜晶系,P2_1/c空间群。晶胞参数为a=8.141(2),b=21.218(6),c=8.597(2),β=107.77(2)°;V=1414.1(6) ~3;Z=2,D_c=1.90g/cm~3,F(000)=780,μ_c=66.3cm~(-1)(MoK_a)。最终的偏离因子R=0.047,R_(to)=0.048。结构分析表明,该配合物是以两个氯离子与金属离子桥联的二聚体形式存在。四氢呋喃中的氧原子同金属离子键合,Er—O键长为2.490(6),两个环戊二烯中的所有碳原子同金属离子间的平均键长为2.649,Er-Cl=2.666(3),Er—Cl-a=2.797(3),Er-Er_a=4.42,Cl-Er-Cl_a键角为72.2°。

海洋聚球蓝细菌（Synechococcus）的纯化鉴定及生理和生态分布特征

利用流式细胞仪分析了聚球蓝细菌在胶州湾的时空分布和营养盐的影响, 并对聚球蓝细菌亚群分化及其影响因子做了进一步探索。分离获得六株海洋聚球蓝细菌，分别定名为IOCAS0401、IOCAS0402、IOCAS0403、IOCAS0404、IOCAS0405、IOCAS0406。对其中两株（IOCAS0401、IOCAS0402）进行鉴定，并进一步研究了其生理生态特征。有三株菌（IOCAS0403、IOCAS0404、IOCAS0405）具有异养生长能力，选取其中两株（IOCAS0403、IOCAS0405）构建了遗传操作系统。具体内容摘要如下： 1、聚球蓝细菌在胶州湾的时空分布和营养盐的影响 胶州湾近一年的微微型浮游植物群落分析表明，聚球蓝细菌逐月的最高丰度中心有从湾外→湾口→湾内，再由湾内→湾口→湾外的变化趋势。在月变化中，聚球蓝细菌9月丰度最大，平均丰度为4.87×103 cells/ml，1-4月丰度很低，其中3月平均丰度最低为66 cells/ml。选取D5站的0 m和30 m作为表层和深层，对微微型浮游植物和营养盐的研究表明，在9、10月，N/P主要在10-30之间，聚球蓝细菌占优势51.6%（9月），98.5％（10月），其它月份大多数N/P<10或者>30，尤其以8月和11月最为显著，而这两个月也恰恰是超微真核浮游植物占优势92.1％（8月），84.8％（11月）。流式细胞仪数据表明，夏末和秋季部分站位会出现聚球蓝细菌的两个亚群，并且当N/P在33左右时可能会出现两个亚群分化，经过对N源的分析后发现，产生亚群分化时NO3-N/PO4-P在14左右。 2、 所分离到的六株聚球蓝细菌的吸收光谱表明，胶州湾的聚球蓝细菌色素种类十分丰富，基本都含有叶绿素a和藻红蛋白（PE），同时也有含藻蓝蛋白（PC）的种群。研究中发现有三株菌具有兼性异养生长能力，当有光照的时候，合成色素，自养生长进行产氧光合作用，没有光照时，色素逐渐消失，启动异养生长的代谢过程。 3、 利用流式细胞仪分析黄海近海水样中聚球蓝细菌种群组成，发现主要有不同藻红蛋白含量的两个类群组成，流式细胞仪分选后，用SN培养基培养纯化得到两个亚群优势种聚球蓝细菌IOCAS0401和IOCAS0402。荧光显微镜下镜检，两株菌在蓝色激发光（450-490 nm）下发桔红色荧光，并且IOCAS0401的荧光较IOCAS0402强。扫描电镜观察发现IOCAS0401呈椭圆形，长轴大约1.2 μm左右；IOCAS0402近似球形，直径约有0.6 μm左右。吸收光谱的检测表明，两者都有叶绿素a和藻红蛋白的特征吸收峰。其中IOCAS0401有藻尿胆素（PUB）和藻红胆素（PEB）吸收锋，而IOCAS0402只有PEB的吸收峰，两者均无藻蓝蛋白（PC）吸收锋。通过16S rDNA测序分析，结果表明两株菌都位于MC-A中的clade II类群，与从日本海域分离获得的MBIC10224菌株有较高的亲缘关系，虽然这三株菌都归为clade II，但单独成一分支，表明它们带有明显的西太平洋特色。 4、 选取其中两株IOCAS0403和IOCAS0405构建遗传系统，抗生素图谱表明，IOCAS0403对四环素有抗性，自然转化结果显示，IOCAS0403不能自然转化，IOCAS0405具有自然转化能力，同时两者都不能进行接合转移。