光敏核不育水稻41 kDa和61 kDa蛋白质的发现、N-端序列分析及其雄性不育性状关系的探讨

光敏核不育水稻农垦58S是石明松于1973年在晚粳农垦58的大田中发现的雄性不育突变体，它在长日照下雄性不育可被用于与恢复系杂交生产杂种，而在短日照下雄性可育能用于自交繁殖，它的恢复系来源广泛。基于这些特性，育种学家用光敏核不育水稻建立的二系杂交水稻制种技术有很大的应用潜力。近十几年来，育种学家用农垦58S作基因供体转育了许多新的不育系，研究结果表明育成的粳型不育系均为光敏不育系，但在育成的籼型不育系中，绝大多数丧失光敏核不育特性，变成温敏不育系。目前因不知光敏核不育的分子遗传机制，尚不能解释这些问题。 本文用双向电泳技术分析了农垦58S和农垦58苗期和育性转换光敏感期叶绿体蛋白质的差异，在农垦58S中发现三个蛋白质(Pl，P2和P3)，其中Pl和P2在苗期和光敏感期叶片内均存在，P3仅在光敏感期的叶片中存在，它们不受长日照或短日照处理的影响。农垦58没有这三个蛋白质。 用制备型双向电泳纯化后，得到SDS - PAGE和IEF纯的Pl和P2。经SDS-PAGE和IEF测定，Pl的等电点是6.2，分子量是41 kDa;P2的等电点是5.8，分子量是61 kDa。现称Pl为P41，P2为P61。氨基酸序列分析和同源性检索发现P41与水稻叶绿体ATP合成酶p亚基和酵母转录因子CAD1有同源性，此外，P41的N-端序列中有一个与蛋白激酶催化核心中的多功能motif Y-G-X-G-X- (P/T)-G-V相似的序列;P61的14个氨基酸长的N-端序列与水稻叶绿体ATP合成酶β亚基的一致。P41和P61 N-端前12个氨基酸的序列也完全一致。 PCR扩增和Southern杂交分析没有发现农垦58S和农垦58之间ATP合成酶β亚基基因(atpB)的多态性。Nothern杂交分析表明农垦58S中仅有一种、与农垦58 atpB mRNA分子量相同的atpB转录产物，但它的atpB mRNA丰度明显低于农垦58的。没有检测到突变的atpB和其它形式的atpB转录产物。 分析P41和P61在其它水稻材料中的分布特点发现它们在粳型光敏不育系7001S、5088S、31301S、C407S和1647S，籼型光敏不育系W7415S和W9451S以及温（光）敏不育系培矮64S中存在，而在对照材料三系水稻马协A、珍汕97A、马协B、珍汕97B和明恢63以及常规粳稻C94153中不存在。根据这些不育系的系谱和它们与农垦58S之间基因的等位性研究结果，讨论了P41和P61与光敏核不育性的可能联系。

Crystallographic and electrochemical characteristics of Ti45Zr35Ni13Pd7 melt-spun alloys

Ti45Zr35Ni13Pd7 alloys are prepared by melt spinning at different cooling rates (v). The phase structure and electrochemical hydrogen storage performance are investigated. When U is 10 m/s, the alloy consists of icosahedral quasicrystalline phase (I-phase), C14 Laves phase and a little amorphous phase. When v increases to 20 or 30 m/s, a mixed structure of I-phase and amorphous phase is formed. Maximum discharge capacity of alloy electrode decreases from 156 mAh/g (v = 10 m/s) to 139 mAh/g (v = 30 m/s) with increasing v. High-rate discharge ability at the discharge current density of 240 mA/g decreases monotonically from 61.2% (v = 10 m/s) to 56.8% (v = 30 m/s).

Novel NIR-absorbing conjugated polymers for efficient polymer solar cells: effect of alkyl chain length on device performance

Three low bandgap conjugated polymers, i.e., PDTPBT-C8, PDTPBT-C6 and PDTPBT-C5, which consist of alternating N-alkyl dithieno[3,2-b: 2',3'-d] pyrrole and 2,1,3-benzothiadiazole units and carry 1-octylnonyl, 1-hexylheptyl and 1-pentylhexyl as side chains, respectively, were synthesized. These polymers show strong absorption in the wavelength range of 600-900 nm with enhanced absorption coefficient as the length of alkyl chain decreases. The film morphology of the polymers and 1-(3-methoxycarbonyl) propyl-1-phenyl-[6,6]-C-61 (PCBM) blends is also dependent on the alkyl chain length. As the length decreases, the film becomes more uniform and the domian size decreases from 400-900 nm for PDTPBT-C8 to similar to 50 nm for PDTPBT-C5.

Investigation of Chemical Bond Characteristics, Thermal Expansion Coefficients and Bulk Moduli of alpha-R2MoO6 and R2Mo2O7 (R = rare earths) by Using a Dielectric Chemical Bond Method

Theoretical researches are performed on the alpha-R2MoO6 (R = Y, Gd, Tb Dy, Ho, Er, Tm and Yb) and pyrochlore-type R2Mo2O7 (R = Y, Nd, Sm, Gd, Tb and Dy) rare earth molybdates by using chemical bond theory of dielectric description. The chemical bonding characteristics and their relationship with thermal expansion property and compressibility are explored. The calculated values of linear thermal expansion coefficient (LTEC) and bulk modulus agree well with the available experimental values. The calculations reveal that the LTECs and the bulk moduli do have linear relationship with the ionic radii of the lanthanides: the LTEC decreases from 6.80 to 6.62 10(-6)/K and the bulk modulus increases from 141 to 154 GPa when R goes in the order Gd, Tb Dy, Ho, Er, Tm, and Yb in the alpha-R2MoO6 series; while in the R2Mo2O7 series, the LTEC ranges from 6.80 to 6.61 10(-6)/K and the bulk modulus ranges from 147 to 163 GPa when R varies in the order Nd, Sm, Gd, Tb and Dy.

Effects of fullerene solubility on the crystallization of poly(3-hexylthiophene) and performance of photovoltaic devices

The substantial crystallization suppression of poly(3-hexylthiophene) (P3HT) in the untreated P3HT:C60 composite film prepared from o-dichlorobenzene (ODCB) solution has been revealed. Besides, the effective conjugation length of P3HT in this composite has been nearly maintained to that in the solution. The different crystallization behaviors of P3HT in its composites with C60 and [6,6]-phenyl C-61 butyric acid methyl ester (PCBM) are mainly attributed to the relative solubility of C60 and PCBM with respect to P3HT in ODCB. The solution to overcome this disadvantage of chain conformation and crystallinity of P3HT in the composite with C60 is thus proposed and finalized by resorting to the addition of low volatile solvent with much higher solubility of C60 than P3HT into the main solvent used, so as P3HT can crystallize before C60 forms crystallites in the solution. The feasibility of this approach has been proven by the improved efficiency of devices based on composites of P3HT and the low cost C60 without resorting to post-treatments.

Rational Design, Synthesis, and Optical Properties of Film-Forming, Near-Infrared Absorbing, and Fluorescent Chiromophores with Multidonors and Large Heterocyclic Acceptors

A new series of film-forming, low-bandgap chromophores (1a,b and 2a,b) were rationally designed with aid of a computational study., and then synthesized and characterized. To realize absorption and emission above the 1000 nm wavelength, the molecular design focuses on lowering the LUMO level by fusing common heterocyclic units into a large conjugated core that acts an electron acceptor and increasing the charge transfer by attaching the multiple electron-donating groups at the appropriate positions of the acceptor core. The chromophores have bandgap levels of 1.27-0.71 eV, and accordingly absorb at 746-1003 nm and emit at 1035-1290 nm in solution. By design, the relatively high molecular weight (up to 2400 g mol(-1)) and non-coplanar structure allow these near-infrared (NIR) chromophores to be readily spin-coated as uniform thin films and doped with other organic semiconductors for potential device applications. Doping with [6,6]-phenyl-C-61 butyric acid methyl ester leads to a red shift in the absorption on]), for la and 2a. An interesting NIR electrochromism was found for 2a, with absorption being turned on at 1034 nm when electrochemically switched (at 1000 mV) from its neutral state to a radical cation state. Furthermore, a large Stokes shift (256-318 nm) is also unique for this multidonor-acceptor type of chromophore.

Polyimides Derived from 1,4-Bis [3-oxy-(N-aminophthalimide)] Benzene

A novel diamine, 1,4-bis [3-oxy-(N-aminophthalimide)] benzene (BOAPIB), was synthesized from 1,4-bis [3-oxy-(N-phenylphthalimide)] benzene and hydrazine. Its structure was determined via IR, H-1 NMR, and elemental analysis. A series of five-member ring, hydrazine-based polyimides were prepared from this diamine and various aromatic dianhydrides via one-step polycondensation in p-chlorophenol. The inherent viscosities of these polyimides were in the range of 0.17-0.61 dL/g. These polymers were soluble in polar aprotic solvents and phenols at room temperature. Thermogravimetric analysis (TGA) showed that the 5% weight-loss temperatures of the polyimides were near 450 degrees C in air and 500 degrees C in nitrogen. Dynamic mechanical thermal analysis (DMTA) indicated that the glass-transition temperatures (T(g)s) of these polymers were in the range of 265-360 degrees C. The wide-angle X-ray diffraction showed that all the polyimides were amorphous.

NOVEL COMPOSITES OF POLY(L-LACTIDE) AND SURFACE MODIFIED BIOACTIVE SiO2-CaO-P2O5 GEL NANOPARTICLES: MECHANICAL AND BIOLOGICAL PROPERTIES

Bioactive SiO2-CaO-P2O5 gel (BAG) nanoparticles with 40 nm in diameter were synthesized by the sol-gel route and further modified via the ring-opening polymerization of lactide on the surface of particles. Surface modified BAG (mBAG) was introduced in poly(L-lactide) (PLLA) matrix as bioactive filler. The dispersibility of mBAG in PLLA matrix was much higher than that of rough BAG particles. Tensile strength of the mBAG/PLLA composite could be increased to 61.2 MPa at 2 wt% filler content from 53.4 MPa for pure PLLA. The variation of moduli of the BAG/PLLA and mBAG/PLLA composites always showed an enhancement tendency with the increasing content of filler loading. The SEM photographs of the fracture surfaces showed that mBAG could be homogeneously dispersed in the PLLA matrix, and the corrugated deformation could absorb the rupture energy effectively during the breaking of materials. In vitro bioactivity tests showed that both BAG and mBAG particles could endow the composites with ability of the calcium sediment in SBF, but the surface modification of BAG particles could weaken this capability to some extent. Biocompatibility tests showed that both BAG and mBAG particles could facilitate the attachment and proliferation of the marrow cells on the surface of the composite.

VUV excitation properties of LnAl(3)B(4)O(12): Re (Ln = Y, Gd; Re=Eu, Tb)

Vacuum ultraviolet excitation spectra of LnAl(3)B(4)O(12):Re (Ln = Y, Gd; Re = Eu, To), along with X-ray photoelectron spectra, were measured. The spectra are tentatively interpreted in terms of the optical properties of the rare earth ions and the band structure. It was found that there is an energy transfer from the hosts to the rare earth ions. It was also found that the top of the valence band in the Gd compound is mainly formed by the 2p levels of O2- and the 4f levels of Gd3+, and in the Y compound mainly by the 2p levels of O2-. (C) 2000 Elsevier Science Ltd. All rights reserved.

In situ synthesis of terbium-benzoic acid complex in sol-gel derived silica by a two-step sol-gel method

Terbium complexes with benzoic acid and its derivatives o-hydroxybenzoic acid and p-hydroxybenzoic acid were in situ synthesized in sol-gel derived silica matrix via a two-step sol-gel process. The formation process of the complex was characterized by fluorescence spectra, absorption spectra and IR spectra. The gels that contain in situ synthesized complexes exhibit the characteristic emission bands of terbium ion. The fluorescence lifetimes of Tb3+ in the silica gels are longer than those in the pure complexes and in the solutions that contain the corresponding complexes. (C) 2000 Elsevier Science Ltd. All rights reserved.

TG-DTA properties of new nonlinear optical materials: K(2)Ln(NO3)(5)center dot 2H(2)O (Ln = La, Ce, Pr, Nd, Sm)

Single crystals of K(2)Ln(NO3)(5). 2H(2)O (KLnN) (Ln = La, Ce, Pr, Nd, Sm) were grown from aqueous solution. The thermogravimetric analysis and differential thermal analysis curves of KLnN demonstrate that the processes of dehydration, melting, irreversible phase transformation and decomposition of NO3- take place in sequence in the heating processes (except KCN). There are three stages in the decomposition of NO3- in KLnN (Ln = La, Nd, Sm) while two in KLnN (Ln = Ce, Pr). K(2)Ln(NO3)(5) is formed at about 225 degrees C by the reaction of KNO3 and Ln(NO3)(3). nH(2)O (Ln = La, Ce, Pr, Nd). (C) 2000 Elsevier Science Ltd. All rights reserved.

A chromic molybdenum phosphate with a tunnel structure: hydrothermal synthesis and structure of (NH3CH2CH2NH3)(2) center dot (NH3CH2CH2NH2)(3)center dot[NaCr2Mo12O30(PO4)(HPO4)(4)(H2PO4)(3)]center dot 6H(2)O

A chromic molybdenum phosphate, (NH3CH2CH2NH3)(2).(NH3CH2CH2NH2)(3).[NaCr2Mo12O30(PO4)(HPO4)(3)]. 6H(2)O, involving molybdenum present in V oxidation, has been hydrothermally synthesized and structurally characterized by single crystal X-ray diffraction and IR spectrum. Deep brown-red crystals are formed in the triclinic system, space group P (1) over bar, a = 12.067(2), b = 14.677(3), c = 21.290(2) Angstrom, alpha = 80.940(10)degrees, beta = 82.960(10)degrees, gamma = 76.61(2)degrees. The structure of the title compound may be considered to be two [Mo6O15(HPO4)(H2PO4)(3)](5-) units bonded to a chromic atom, although several P-O groups are not protonated on account of coordination with a Na+ cation. The one-dimensional tunnels were formed in the solid of the title compound. (C) 2000 Elsevier Science B.V. All rights reserved.

The application and a substitution defect model for Eu3+ -> Eu2+ reduction in non-reducing atmospheres in borates containing BO4 anion groups

The variations of emission intensities of SrB4O7:Eu2+ and Sr2B5O9Cl:Eu2+ prepared in different atmospheres are discussed in view of the structure of host compounds. A model of substitution defects is proposed to explain the abnormal reduction of Eu3+ --> Eu2+ in non-reducing atmospheres of N-2, air and O-2. Experiment results show that SrB4O7:Eu2+ phosphor sample prepared in N-2 atmosphere has an emission intensity of 94% as high as that of the sample prepared in H-2 gas. This implies that the reduction of Eu2+ --> Eu2+ in non-reducing atmospheres could be potentially used in preparing phosphors, such as SrB4O7:Eu2+. (C) 1999 Elsevier Science Ltd. All rights reserved.

Sodium ion transfer across micro water/1,2-DCE interface facilitated by liquid crystal crown ether

The sodium ion transfer across the micro-water/1,2-dichloroethane interface facilitated by a novel ionophore, liquid crystal crown ether was studied systematically. The sodium ion transfer facilitated by LCCE is controlled by diffusion studied by cyclic voltammetry. The diffusion coefficient of LCCE in 1,2-dichloroethane was calculated to be equal to (2.61 +/- 0.12) X 10(-6) cm(2)/s and the stability constant of the complex between Na+ and LCCE was determined as lg beta (o) = 5.7 in 1,2-dichloroethane.