Flip-chip bonded hybrid CMOS/SEED optoelectronic smart pixels

Hybrid integration of GaAs/AlGaAs multiple quantum well self electro-optic effect device (SEED) arrays are demonstrated flip-chip bonded directly onto 1 mu m silicon CMOS circuits. The GaAs/AlGaAs MQW devices are designed for 850 nm operation. Some devices are used as input light detectors and others serve as output light modulators. The measurement results under applied biases show good optoelectronic characteristics of elements in SEED arrays. Nearly the same reflection spectrum is obtained for the different devices at an array and the contrast ratio is more than 1.2:1 after flip-chip bonding and packaging. The transimpedance receiver-transmitter circuit can be operated at a frequency of 300 MHz.

Flip-chip bonded hybrid CMOS/SEED optoelectronic smart pixels

Hybrid integration of GaAs/AlGaAs multiple quantum well self electro-optic effect device (SEED) arrays are demonstrated flip-chip bonded directly onto 1 mu m silicon CMOS circuits. The GaAs/AlGaAs MQW devices are designed for 850 nm operation. Some devices are used as input light detectors and others serve as output light modulators. The measurement results under applied biases show good optoelectronic characteristics of elements in SEED arrays. Nearly the same reflection spectrum is obtained for the different devices at an array and the contrast ratio is more than 1.2:1 after flip-chip bonding and packaging. The transimpedance receiver-transmitter circuit can be operated at a frequency of 300 MHz.

Determination of sulfur-containing compounds in diesel oils by comprehensive two-dimensional gas chromatography with a sulfur chemiluminescence detector

This article reports an analytical method for separating, identifying and quantitating sulfur-containing compounds and their groups in diesel oils (170-400degreesC) using comprehensive two-dimensional gas chromatography coupled with a sulfur chemiluminescence detector. The identification of target compounds and their groups was based on standard substances, the group separation feature and the-effect of comprehensive two-dimensional gas chromatography. The quantitative analysis on major sulfur compounds and total sulfur was carried out based on the linear response of sulfur chemiluminescence detector and the internal standards method. The results of total sulfur determination in the samples were compared with those from ASTM D 4294 standard method, the R.S.D. percentage were <6.02%, correctness of this method can meet the industrial requirement. To the end, the method developed was used to investigate the sulfur-containing compounds in different diesel oils, the result shows that the distribution of sulfur-containing compounds in diesel oils from different process units are apparently different. The sulfur compounds in fluid catalytic cracking (FCC), residuum fluid catalytic cracking (RFCC) diesel oils mainly exist in the form of alkyl-substituted dibenzothiophenes that add up to about 40-50% of the total sulfur, while this number is only 6-8 and 20-28% in visbreaking (VB) and delayed-coking (DC) diesel oils, respectively. (C) 2003 Elsevier B.V. All rights reserved.

Fruit anatomy,seed germination and seedling development in the Japanese seagrass phyllospadix

Phyllospadix iwatensis Makino and phyllospadix japonicus Makino have similar frunt morphology and anatomy.The rhomboid fruit of Japanese phyllospadix is dark brown in colour and is characterized by two arms bearing stiff inflected bristles which can act as an anchoring system. The fruit covering consists of a thin cuticular seed coat and pericarp remains mainly fibrous endocarp. In the groove region of the fruit.the cuticular seed coat and endocarp are replaced by nucellus cells with wall in growths and crushed pigment strands with lignified walls.these tissues appera to control the transfer of nutrients to developing seed.the seed is oval with a small embryo and a large hypocotyl. the embryo is straight and simple,with the plumule containing three leaf primordia and a pair of root primordia surrounded by a cotyledon.the hypocotyl has large vontral lobe containing central provascular tissue and two small dorsal lobes.the hypocotyl contains starch.lipid and protein.and acts as a nutrient store.the seed of P.iwatensis has a dormancy period of 2-6 weeks and germination eventually reaches-65%.but is not synchronized.during germination the leaves emerge first.and then after at least three young leaves have formed and abseised.the roots emerge,usually?6 months after the commencement of germination.Utilizaton of the nutrient reserves is initially from the perihpery of the hypocotyl and then progressively towards its centre.

Chemical Constituents of Nitraira tangutorum Seed from Qaidam Basin

Six compounds were isolated from the 75% ethanol extract of Nitraria tangutorum seed.On the basis of spectroscopic methods including 1H NMR,13C NMR and ESI-MS and comparison with literature,their structures were elucidated as daucosterol(1),4-hydroxypipecolic acid(2),quercetin(3),allantoin(4),1,2,3,4-tetrahydro-1-methyl-β-carboline-3-carboxylic acid(5) and L-tyrosine(6).Compounds 1,2,3,5 and 6 were isolated from Nitraria tangtorum for the first time.

Extraction of Nitraria tangutorum seed oil by supercritical carbon dioxide and determination of free fatty acids by HPLC/APC/IMS with fluorescence detection

The seed oil from Nitraria tangutorum samples was obtained by supercritical carbon dioxide extraction methods. The extraction parameters for this methodology, including pressure, temperature, particle size and extraction time, were optimized. The free fatty acids in the seed oil were separated with a pre-column derivation method and 1,2-benzo-3,4-dihydrocarbazole-9-ethyl-p-toluenesulfonate (BDETS) as a labeling regent, followed by high-performance liquid chromatography (HPLC) with fluorescence detection. The target compounds were identified by mass spectrometry with atmospheric pressure chemical ionization (APCI in positive-ion mode). HPLC analysis shows that the main compositions of the seed oil samples were free fatty acids (FFAs) in high to low concentrations as follows: linoleic acid, oleic acid, hexadecanoic acid and octadecanoic acid. The assay detection limits (at signal-to-noise of 3:1) were 3.378-6.572 nmol/L. Excellent linear responses were observed, with correlation coefficients greater than 0.999. The facile BDETS derivatization coupled with mass spectrometry detection allowed the development of a highly sensitive method for analyzing free fatty acids in seed oil by supercritical CO2 extraction. The established method is highly efficient for seed oil extraction and extremely sensitive for fatty acid profile determination. (C) 2007 Elsevier B.V. All rights reserved.

Comparative analysis of allantoin quercetin, and 1-methyl-1,2,3,4-tetrahydro-beta-carboline-3-carboxylic acid in Nitraria tangutorum Bobr. Seed by HPLC-APCI-MS and CE

This paper describes the simultaneous determination of allantoin, quercetin, and 1-methyl-1,2,3,4-tetrahydro-beta-carboline-3-carboxylic acid (MTCCA) in Nitraria tangutorum Bobr seed by HPLC-APCI-MS and CE (capillary electrophoresis) methods. The final optimized chromatographic conditions were investigated in a reversed-phase Eclipse XDB-C8 column (150 x 4.6 mm, 5 mu m). A seventeen-minute gradient elution, (A: aqueous acetonitrile 20% (v/v); B: aqueous acetonitrile 60% (v/v); C: pure acetonitrile 100%) at a flow rate of 1.0 mL/min was selected for the separation of three natural products with diode array detection (DAD) at 220 nm. A CE experiment was carried out in a fused silica capillary with 32 mmol/L boric acid (pH 10), 32 mmol/L SDS and acetonitrile (10.0%, v/v). The applied potential and temperature was, respectively, set at 19 kV and 25 degrees C. After development, the validation was performed in parallel for HPLC and CE, with the same standards and sample to avoid differences due to the manipulation. The validation parameters of both techniques were adequate for the intended purpose.

Direct Numerical Simulation of a Spatially Evolving Supersonic Turbulent Boundary Layer at Ma=6

Direct numerical simulation is carried out for a spatially evolving supersonic turbulent boundary layer at free-stream Mach number 6. To overcome numerical instability, the seventh-order WENO scheme is used for the convection terms of Navier-Stokes equations, and fine mesh is adopted to minimize numerical dissipation. Compressibilty effects on the near-wall turbulent kinetic energy budget are studied. The cross-stream extended self-similarity and scaling exponents including the near-wall region are studied. In high Mach number flows, the coherence vortex structures are arranged to be smoother and streamwised, and the hair-pin vortices are less likely to occur.

The Effect of Conical Flowfields on the Performance of Waveriders at Mach 6

The performance of 23 kinds of waveriders, derived from different conical flowfields, is analyzed by the numerical computation under the conditions of fight speed of Mach 6, attack angle of 0° and flight altitude of 30 km. These results indicate that the performance is influenced by the shapes and the width to height ratios (W/H ) of generating cones. The geometrical parameter and the lift coefficient are proportional to W/H, while the drag coefficient and the lift to drag ratio (L/D ) have extreme values. Considering the base drag and the computation errors, the waverider with the highest L/D is cut from the elliptical cone’s flowfield (W/H = 1.5―1.618), and the configuration with the lowest drag can also be obtained at W/H = 1:1.5. Accordingly, good suggestions are proposed for practical design based on these computational results.

A study on stratification of concentration in crystal-growth of alpha-liio3 by holographic-interferometry

A new thermoplastic-photoconductor laser holographic recording system has been used for real-time and in situ observation of alpha-LiIO3 crystal growth. The influence of crystallization-driven convection on the concentration stratification in solution has been studied under gravity field. It is found that the stratification is closely related to the seed orientation of alpha-LiIO3 crystal. When the optical axis of crystal seed C is parallel to the gravity vector g, the velocity of the concentration stratification is two times larger than that in the case of C perpendicular-to g. It needs 40 h for the crystalline system of alpha-LiIO3 to reach stable concentration distribution (expressed as tau) at 47.6-degrees-C. The time tau is not sensitive to the seed orientation. Our results provide valuable data for designing the crystal growth experiments ia space.

6马赫锥体流场对乘波体性能的影响及规律

以CFD计算为分析工具，在6马赫飞行速度、0°飞行攻角和30km飞行高度的设计条件下，综合分析了23种源自不同锥体流场所获乘波体的性能．分析结果表明，基本锥体的截面形状及截面宽高比均对乘波体性能有较大影响；当基本锥体的宽高比变化时，相应乘波体几何参数和升力系数的变化基本与之呈正比关系，而阻力系数及升阻比则出现极值．此外，我们发现在此飞行状态下，综合考虑乘波体底部阻力及计算误差等因素，当基本锥体为椭圆锥，且截面椭圆宽高比在1．5～1．618时，所获得的乘波体具有最大的升阻比；而当截面椭圆宽高比约为1：1．5时，所获得乘波体阻力最小．依据所得的计算结果，对于乘波飞行器的实际设计给出了相应的建议．

Experimental Studies on Model Scramjet in a Mach 6 High Enthalpy Free-Jet Wind Tunnel

A side-wall compression scramjet model with different combustor geometries has been tested in a propulsion tunnel that typically provides the testing flow with Mach number of 5.8, total temperature of 1800K, total pressure of 4.5MPa and mass flow rate of 4kg/s. This kerosene-fueled scramjet model consists of a side-wall compression inlet, a combustor and a thrust nozzle. A strut was used to increase the contraction ratio and to inject fuels, as well as a mixing enhancement device. Several wall cavities were also employed for flame-holding. In order to shorten the ignition delay time of the kerosene fuel, a little amount of hydrogen was used as a pilot flame. The pressure along the combustor has an evident raise after ignition occurred. Consequently thrust was observed during the fuel-on period. However, the thrust was still less than the drag of the scramjet model. For this reason, the drag variation produced by different strut and cavities was tested. Typical results showed that the cavities do not influence the drag so much, but the length of the strut does.

Visual C++ 6.0学习教程

MicrosoftVisualC十十6.0作为Microsoft Visual Studio的重要组成部分，包含了迄今为止功能最为强大的基于Windows的应用框架，在同类产品中处于领先地位。VisualC十十6.0是Microsoft迄今为止最全面、最完善的程序开发工具，为了适应各种编程风格，该软件提供了各种各样的辅助工具，在发挥编程能力和提高灵活性方面达到了空前的水平。与以往VisualC十十的各种版本相比较，VisualC十十6.0在编程环境、程序语言技术等方面做了许多改进，从而使VisualC十十更加适合专业程序员快速进行应用程序的开发。

本书内容丰富、图文并茂，是一本适合各种读者学习VisualC十十6.0的优秀参考书。

目 录
第一章 VisualC十十6.0简介及安装
1.1VisualC十十6.0新特性
1.2viSualC十十6.0开发环境简介
1.3如何学习使用VisualC十十6.0
1.4VisualC十十6.0的安装
第二章 走进C十十的世界
2.1类和对象的简介
2.2继承和多态性――一个具体的例子
2.3内嵌对象
2.4在栈中申请对象
2.5全程对象的申请
2.6对象之间的相互关系――指针数据成员
2.7this指针的使用
2.8对指针的引用
2.9友元类和友元函数
2.10静态类成员
2.11重载运算符
2.12从代码中分离出类定义
2.13匈牙利表示法
第三章 VisualC十十6.0的编程环境
3.1VisualC十十6.0主窗口
3.2VisualC十十6.0工具栏
3.3VisualC十十6.0菜单栏
3.4项目与项目工作区
3.5资源与资源编辑器
第四章 编一个最简单的VC十十程序
4.1什么是AppWizard？
4.2迎接你的第一个AppWizard程序
4.3“Iamaprogrammer.”在哪儿？
第五章 程序框架入门
5.1一个简化过的程序框架
5.2WinMain（）：第一个动作
5.3登记窗口类
5.4创建一个窗口
5.5显示窗口
5.6显示出那条消息
5.7窗口类与窗口对象
第六章 消息循环
6.1在消息循环中兜圈子
6.2对事件做出响应：WindowFun（）
6.3响应不同的消息
6.4现在你还跟得上吗？
6.5设备界面进行交互
第七章 精通程序框架
7.1WinMain（）函数在哪儿？
7.2应用程序框架和源文件
7.3工具条、状态条和打印等选项
7.4程序的控制流程
第八章 使用classWizard编程
8.1使用ClassWizard添加消息处理函数
8.2classWizard功能介绍
8.3传送鼠标消息
8.4保存鼠标绘图的信息
第九章 视图与文档
9.1Document－View模式
9.2从视图中分离出文档
9.3保存文档
9.4再访MyProg2.cpp
第十章 对象连接与嵌入（OLE）及其自动化
10.1公共对象模式（COM）
10.2类厂（classfactory）
10.3OLE自动化
10.4IDispatch接口
第十一章 动态连接库（DLLs）
11.1为什么使用DLL
11.2传统的DLL
11.3MFC库DLL
11.4MyProg4A――编写自己的类库扩展DLL
11.5MyProg4B――使用MFC库扩展DLL
11.6资源访问
第十二章 图形设备接口
12.1设备环境类
12.2GDI对象
12.3Windows的颜色映射
12.4映射方式
12.5字体
12.6MyProg3例程序
12.7MyProg3B程序
12.8MyPr0g3C例程序――使用CScrollView
第十三章 对话框
13.1在状态条上显示对话控件的帮助信息
13.2利用Fi1eOpen通用对话框打开多个文件
13.3定制通用文件对话框
13.4扩展和缩减一个对话框
13.5显示一个模式或无模式对话框
13.6编写定制的DDX/DDV例程
第十四章 剖析工具Spy十＋
14.1窗体
14.2消息
14.3进程与线程
第十五章 代码调试
15.1TRACE
15.2调试框架
15.3自我诊断
15.4调试代码的作用
15.5用Dump（）显示对象的信息
15.6检查内存

Laser action from 1,3,5,7-tetramethyl-2,6-diethyl-8-n-propyl pyrromethene-BF2

We measured spectroscopic and laser action properties of a novel 8-position substituted pyrromethene-BF2, namely 1,3,5,7-tetramethyl-2,6-diethyl-8-n-propyl pyrromethene-BF2 complex. The laser action was performed with the corresponding dye solution in ethanol, which was placed in a Littman-type laser cavity pumped by the second harmonic of a Q-switched Nd:YAG laser. The spectroscopic measurements clearly indicated that the corresponding dye solution in ethanol exhibited intense absorption in the visible spectral region with large fluorescence quantum yield. It possesses rather low triplet-triplet absorption in the spectral region 460-550 nm and almost negligible triplet-triplet absorption in the lasing spectral region. As a consequence, it lases nearly as efficiently as commercially available benchmark laser dyes such as Rhodamine-6G and outperformed them in wavelength tunability in our laser cavity and pump geometry. (C) 2002 Optical Society of America.