利用射流泵输送油水两相管流的实验研究

研究了应用射流泵输送油水两相管流时泵对下游管道中流型和压降的影响。实验管线为内径50mm的透明有机玻璃管，管线从入口到分离器长约35m，实验段由一个垂直倒U型管和一个长3m水平管组成。分别给出了不同入口条件下实验管段的流型图和压降图。结果表明：采用射流泵输送油水两相流动，对下游管道流型和油水乳化速度有着显著的影响，但对下游管道内的压降随混合流速和体积份额的变化趋势影响很小。

Equivalent Model Of Expansion Of Cement Mortar Under Sulphate Erosion

The expansion property of cement mortar under the attack of sulfate ions is studied by experimental and theoretical methods. First, cement mortars are fabricated with the ratio of water to cement of 0.4, 0.6, and 0.8. Secondly, the expansion of specimen immerged in sulphate solution is measured at different times. Thirdly, a theoretical model of expansion of cement mortar under sulphate erosion is suggested by virtue of represent volume element method. In this model, the damage evolution due to the interaction between delayed ettringite and cement mortar is taken into account. Finally, the numerical calculation is performed. The numerical and experimental results indicate that the model perfectly describes the expansion of the cement mortar.

Evolution of thermoplastic shear localization and related microstructures in Awl/SiCp composites under dynamic compression

The localized shear deformation in the 2024 and 2124 Al matrix composites reinforced with SiC particles was investigated with a split Hopkinson pressure bar (SHPB) at a strain rate of about 2.0x10(3) s(-1). The results showed that the occurrence of localized shear deformation is sensitive to the size of SiC particles. It was found that the critical strain, at which the shear localization occurs, strongly depends on the size and volume fraction of SiC particles. The smaller the particle size, the lower the critical strain required for the shear localization. TEM examinations revealed that Al/SiCp interfaces are the main sources of dislocations. The dislocation density near the interface was found to be high and it decreases with the distance from the particles. The Al matrix in shear bands was highly deformed and severely elongated at low angle boundaries. The Al/SiCp interfaces, particularly the sharp corners of SiC particles, provide the sites for microcrack initiation. Eventual fracture is caused by the growth and coalescence of microcracks along the shear bands. It is proposed that the distortion free equiaxed grains with low dislocation density observed in the center of shear band result from recrystallization during dynamic deformation.

流变学研究的若干问题

本文综述了1988年8月第10届国际流变学会议部分大会邀请报告及分组报告的下列几个领域内容:①分子动力学;②光学流变测量;⑧血液的动态测量;④数值仿真;⑤钻探油井;⑥强化采油;⑦减阻;⑧聚合物挤压成形加工;⑨食品流变学.

理想塑性材料扩展裂纹的平面应变问题

本文从三维塑性流动理论出发,导出了理想塑性材料平面应变问题的基本方程.进而对扩展裂纹问题建立了完整的定解方程和速度场求解公式.已有的渐近方程只是预解方程和零级定解方程的组合.本文证实了已有的中心扇形区,虽然满足了渐近方程,但不能适应高阶渐近方程.

论长期稳定性和动力稳定性

<正> 根据Lejeune-Dirichlet定理,力学系统处于静平衡情形的稳定的充要条件是系统的势能在平衡位置具有极小值。对于旋转的力学系统(机械系统或液体系统)就不象这样简单了。早在100年前Thomson和Tait就指出了旋转力学系统具有长期稳定性(secular stability)和动力稳定性(dynamiC stability)的重要差别。对于旋转液体星准稳演化过程到底按哪一种稳定性判断,是一个争论近百年的问题。在本世纪50年代以前,Thomson,Tait,Poincare,Liapounoff,Darwin,Teans和Lamb等,主张“长期稳定是真实的稳定”,“是天体演化学唯一感兴趣的稳定”。基于这种观点建立的Jeans-Darwin双星分裂理论曾

绕圆柱体跨声速流场

本文将保角曲线坐标方法应用于绕物体外部的跨声速流动.文中讨论了圆柱体跨声速绕流,计算了来流马赫数M_∞。为亚临界,超临界和M_∞为l的流场.给出了不同来流马赫数下柱面马赫数和压力分布,柱面前端中心流线上马赫数分布.给出了超临界绕流时不同来流马赫数下的声速线和来流马赫数M_∞从0.2,0.3到1的等马赫数线分布.本文部分结果与已有的理论结果进行了比较.本方法计算简单,精度好,是计算厚体跨声速绕流的有效方法,适用于不同形状的柱体和机翼的跨声速绕流.

Equilibrium of isolated magnetostatic flux structure

Two-dimensional magnetostatic models of flux structure confined in stratified atmosphere are discussed in the present paper. The magnetic field in the flux structure is assumed to be force-free at the first step. Numerical solutions for this nonlinear free boundary problem are obtained by finite element method. Results show clearly the relation between the inside fields and outside pressure, especially the influence of atmospheric pressure distribution on the flux structure.

Crack extension and kinking in laminates and bicrystals

Singular fields at the tip of an interface crack in anisotropic solids are reviewed with emphasis on establishing a framework to quantify fracture resistance under mixed mode conditions. The concepts of mode mixity and surface toughness are unified by using generalized interface traction components. The similarity between the anisotropic theory and existing isotropic theory is shown. Explicit formulae are given for misoriented orthotropic bimaterials with potential applications envisioned including composite laminates and semiconductor crystals. Competition between crack extension along the interface and kinking into the substrate is investigated using a boundary layer formulation. Several case studies reveal the role of anisotropy. An explicit complex variable representation for orthotropic materials and a solution to a dislocation interacting with a crack are presented in two self-contained Appendices.

The dynamic evolution of the kepler supernova remnant

been analyzed in detail. The effects ofm icroscopic energy transfer from

EQUIVALENT MODEL OF EXPANSION OF CEMENT MORTAR UNDER SULPHATE EROSION

The expansion property of cement mortar under the attack of sulfate ions is studied by experimental and theoretical methods. First, cement mortars are fabricated with the ratio of water to cement of 0.4, 0.6, and 0.8. Secondly, the expansion of specimen immerged in sulphate solution is measured at different times. Thirdly, a theoretical model of expansion of cement mortar under sulphate erosion is suggested by virtue of represent volume element method. In this model, the damage evolution due to the interaction between delayed ettringite and cement mortar is taken into account. Finally, the numerical calculation is performed. The numerical and experimental results indicate that the model perfectly describes the expansion of the cement mortar.

Electro-optic integration of embedded electrodes and waveguides in LiNbO3 using a femtosecond laser

We describe the fabrication of a Mach-Zehnder optical modulator in LiNbO3 by femtosecond laser micormachining, which is composed of optical waveguides inscripted by a femtosecond laser and embedded microelectrodes subsequently using femtosecond laser ablation and selective electroless plating. A half-wave voltage close to 19 V is achieved at a wavelength of 632.8 nm with an interaction length of 2.6 mm. This simple and cost-effective technique opens up new opportunities for fabricating integrated electro-optic devices. (C) 2008 Optical Society of America