~(195)Os衰变性质的观测

由14MeV中子照射天然铂靶,通过198Pt(n,α)反应产生195Os。用γ(X)γ符合方法搜索了195Os的衰变γ射线,结果没有找到可以属于它衰变的γ射线。

Nonuniformity Effect of Surface-Nanocrystalline Materials in Nanoindentation Test

In the present research, microstructures of the surface-nanocrystalline Al alloy material are observed and measured based on the transmission electron microscopy (TEM) technique, and the corresponding mechanical behaviors are investigated experimentally and theoretically. In the experimental research, the nanoindentation test method is used, and the load and microhardness curves are measured, which strongly depend on the grain size and grain size nonuniformity. Two kinds of the nanoindentation test methods are adopted: the randomly selected loading point method and the continuous stiffness method. In the theoretical modeling, based on the microstructure characteristics of the surface-nanocrystalline Al alloy material, a dislocation pile-up model considering the grain size effect and based on the Mott theory is presented and used. The hardness-indent depth curves are predicted and modeled.

Effect of Carbon Addition on Microstructure and Mechanical Properties of Ti-Based Bulk Metallic Glass Forming Alloys

A kind of novel Ti-based composites was developed by introducing different amounts of carbon element to the Ti-50 Cu-23 Ni-20 Sn-7 bulk metallic glass forming alloys. The thermal stability and microstructural evolution of the composites were investigated. Room temperature compression tests reveal that the composite samples with 1% and 3% (mass fraction) carbon additions have higher fracture strength and obvious plastic strain of 2 195 MPa, 3.1% and 1 913 MPa, 1.3% respectively, compared with those of the corresponding carbon-free Ti-50 Ni-20 Cu-23 Sn-7 alloys. The deformation mechanisms of the composites with improved mechanical properties were also discussed.

Shear deformation analysis on laser-induced reverse bulging and plugging

A new kind of failure mode is observed in circular brass foils in which their peripheries are fixed and their surfaces are subjected to a long pulsed laser over a central region. The failure is classified into three stages; they are referred to as thermal bulging, localized shear deformation and perforation by plugging. A distinct feature of the failure mode is that bulging and plugging occurred in the direction opposite to the incident laser beam. To study the failure mode, we investigate the non-linear response of heated, non-homogeneous circular plates. Based on the large deflection equations of Berger [J. Appl. Mech. 22 (3), 465-472 (1965)], Ohnabe and Mizuguchi [Int. J. Non-Linear Mech. 28 (4), 365-372 (1993)] and the parabolic shear deformation theory of Bhimaraddi and Stevens [J. Appl. Mech. 51 (1), 195-198 (1984)], we have derived new coupled governing equations of shear deformation and deflection. The new equations are solved, for the plate with a clamped edge, by the Galerkin and iterative methods. The numerical results for the shear deformation distribution are in good agreement with the experimental observation.

Measuring Binding Kinetics Of Surface-Bound Molecules Using The Surface Plasmon Resonance Technique

Surface plasmon resonance (SPR) technology and the Biacore biosensor have been widely used to measure the kinetics of biomolecular interactions in the fluid phase. In the past decade, the assay was further extended to measure reaction kinetics when two counterpart molecules are anchored on apposed surfaces. However, the cell binding kinetics has not been well quantified. Here we report development of a cellular kinetic model, combined with experimental procedures for cell binding kinetic measurements, to predict kinetic rates per cell. Human red blood cells coated with bovine serum albumin and anti-BSA monoclonal antibodies (mAbs) immobilized on the chip were used to conduct the measurements. Sensor-grams for BSA-coated RBC binding onto and debinding from the anti-BSA mAb-immobilized chip were obtained using a commercial Biacore 3000 biosensor, and analyzed with the cellular kinetic model developed. Not only did the model fit the data well, but it also predicted cellular on and off-rates as well as binding affinities from curve fitting. The dependence of flow duration, flow rate, and site density of BSA on binding kinetics was tested systematically, which further validated the feasibility and reliability of the new approach. Crown copyright (c) 2008 Published by Elsevier Inc. All rights reserved.

Electrothermal stress in conductive body with collinear cracks

The temperature and stress field in a thin plate with collinear cracks interrupting an electric current field are determined. This is accomplished by using a complex function method that allows a direct means of finding the distribution of the electric current, the temperature and stress field. Temperature dependency for the heat-transfer coefficient, coefficient of linear expansion and the elastic modulus are considered. As an example, temperature distribution is calculated for an alloy (No. GH2132) plate with two collinear cracks under high temperature. Relationships between the stress, temperature, electric density and crack length are obtained. Crack trajectories emanating from existing crack are predicted by application of the strain energy density criterion which can also be used for finding the load carrying capacity of the cracked plate. (C) 2003 Elsevier Ltd. All rights reserved.

复合材料及其结构的非线性力学问题

本文根据最近文献及新近进展,讨论了复合材料及其结构的非线性力学问题,这是一个在实用上和理论上很重要并且越来越重要的问题。

有涨落效应的磁流体静力学关系——局部展开

本文采用局部展开的方法,分析了湍流近似条件下的磁流体静力学关系。对于涨落的、平均的动量守恒和磁感应方程,都得到了可以自洽的湍流场关系。与普通的静力学关系相比,湍流场引进的力包括与平均场平行和垂直分量的力1/(4π)(a~((1))×B_0)×B_0,以及与平均场垂直的由湍流边值引进的力1/(4π)k×B_0。对于二维磁场位形,基本方程可化为一个二阶椭圆型方程,其中包括由涨落场引进的一些线性和非线性项。湍流场使磁场位形改变,可使位形非均匀剪切。在许多天体物理环境中都观测到湍流场,因此研究湍流场的影响是重要的。

交流电磁流体直接发电的粘性影响

<正> 本文在磁雷诺数不作任何限制的条件下,对直管感应式发电器(图1)计算了粘性对电参数和流场的影响,并着重探索各种因素对功率因子的影响。

Quantum and variational monte-carlo interaction potentials for li2 (x1-sigma-g+)

Optimized trial functions are used in quantum Monte Carlo and variational Monte Carlo calculations of the Li₂(X ¹Σ⁺_g) potential curve. The trial functions used are a product of a Slater determinant of molecular orbitals multiplied by correlation functions of electron—nuclear and electron—electron separation. The parameters of the determinant and correlation functions are optimized simultaneously by reducing the deviations of the local energy E_L (E_L  Ψ⁻¹_THΨ_T, where Ψ_T denotes a trial function) over a fixed sample. At the equilibrium separation, the variational Monte Carlo and quantum Monte Carlo methods recover 68% and 98% of the correlation energy, respectively. At other points on the curves, these methods yield similar accuracies.

Thermo-plastic instability in simple shear

A theoretical description of thermo-plastic instability in simple shear is presented in a system of equations describing plastic deformation, the first law of thermodynamics and Fourier's heat transfer rule. Both mechanical and thermodynamical parameters influence instability and it is shown that two different modes of instability may exist. One of them is dominated by thermal softening and has a characteristic time and length, connected to each other by thermal diffusion.A criterion combining thermal softening, current stress, density, specific heat, work-hardening, thermal conductivity and current strain rate is obtained and practical implications are discussed.

流式细胞术分析强声波对植物细胞周期的影响

应用流式细胞术分析烟草细胞在交变应力作用下细胞周期的变化。用特制的强声波发生装置产生频率和强度可调的交变应力场,研究不同频率和强度的交变应力作用后烟草细胞周期的变化。实验结果表明,在交变应力作用下直接影响细胞或细胞分裂的同步化,促进S期的DNA合成,有助于细胞有丝分裂。声波频率在400Hz至800Hz,强度在90dB到110dB内,随频率和强度的增加,交变应力使S期细胞明显增加,但频率或强度过大,反而使S期细胞大大减少。

弯曲直径对多模光纤激光器输出性能的影响

大模场面积(LMA)多模光纤激光器的输出性能与光纤的弯曲程度有关。为研究两者之间的关系，在光纤不同弯曲直径下，对多模光纤激光器的输出性能进行了实验测量和理论计算。采用刀口法测量了不同弯曲直径下的激光光束质量因子M2，并对每种情况下光纤激光器的斜率效率进行了测量。光纤弯曲直径分别为285 mm,195 mm和130 mm时，多模光纤激光器光束质量因子M2为2.88,1.82和1.67，斜率效率为39%,35%和34%。另外，对于实验所采用的大模场面积多模光纤，理论计算了各模式损耗与光纤弯曲直径的关系。