功能化聚丙烯及其与聚对苯二甲酸丁二醇酯共混物的制备及结构性能研究

本工作通过电子束预辐照处理和反应挤出方法，制备了丙烯酸功能化预辐照聚丙烯rPP-g-AA，采用化学滴定和红外光谱方法均证明接枝共聚物的存在，同时确定了预辐照剂量和单体浓度对接枝率的影响：（1）当单体浓度一定时，接枝率随预辐照剂量的增加而增加并逐渐达到平台值；（2）当预辐照剂量固定时，单体浓度在0～4.0wt%范围内，接枝率几乎呈线性增加。研究发现，丙烯酸(AA)接枝链能起到异相成核作用而促进预辐照聚丙烯(rPP)的结晶过程，但却不改变结晶晶型；虽然接枝反应可以部分抑制降解反应，但相对于原料聚丙烯(PP)，接枝产物的力学性能仍大大下降；因此提出的反应机理认为接枝反应主要是通过链断裂降解反应形成的端自由基引发的，从而形成了以端基接枝为主的产物。 为了控制PP接枝过程中的严重降解，本工作首次提出了均相和异相引发接枝反应的原理，即采用部分rPP和预辐照聚乙烯(rPE)分别作为PP接枝反应的均相和异相“引发剂”，经反应挤出制备丙烯酸功能化聚丙烯PP-g-AA。对于均相引发体系：（1）当rPP用量为20phr时，PP-g-AA的接枝率已经达到rPP-g-AA的水平，而且降解反应得到有效控制；（2）和PP/rPP-g-AA共混物的对比研究证明，均相引发接枝产物不但接枝率明显提高，而且接枝分布非常均匀；（3）由此提出均相引发主要是发生rPP和PP分子间夺氢反应并形成以基体PP接枝为主的产物，而rPP分子内夺氢反应形成的接枝产物rPP-g-AA只占较少比例。对于异相引发体系： （1）通过红外光谱表征及接枝率计算得出异相引发接枝产物的接枝率比相应的PP/ rPE-g-AA共混物略高；（2）由于rPE及rPE-g-AA对基体PP的结晶没有影响，通过异相引发接枝产物中PP的结晶温度升高直接验证了异相引发接枝反应的实现；（3）提出的机理认为异相引发主要发生在rPE的分子内夺氢并形成rPE-g-AA，造成rPE引发的PP分子间夺氢反应形成PP-g-AA产物的比例下降。 本工作还详细研究了rPP预辐照剂量、rPP用量和单体浓度对均相引发反应的影响。得到的结果如下：（1）高预辐照剂量导致了接枝率下降的“假相”是由于形成的微凝胶造成的；（2）rPP用量的增大在提高接枝率的同时也导致降解反应的逐渐增强；（3）单体浓度的增加导致接枝率的逐步提高并最终达到最大值，而且可能导致部分微凝胶的产生；（4）接枝没有破坏PP-g-AA结晶的完善性和晶型，却能促进了晶体在（040）晶面的生长并可能产生部分横晶形态；（5）PP-g-AA和金属能形成良好的粘接作用。 以上述制备的rPP-g-AA和PP-g-AA增容PP/聚对苯二甲酸丁二醇酯(PBT)共混体系，发现高分子量的PP-g-AA比低分子量的rPP-g-AA的增容效果要好，因此认为PP-g-AA和PBT通过酯化反应形成的长链接枝共聚物PP-g-PBT对PBT相的分散和界面作用增强更加有效。而随着增容剂PP-g-AA比例的增加，原位反应生成的PP-g-PBT逐渐增加，使得PBT相分散和界面增强效果更加显著，因此共混物的力学性能也更佳；DSC研究发现，随着PBT相尺寸减小到1μm以下，PBT出现了结晶受限行为。 将引发剂rPP和单体AA加入到PP/PBT共混体系中实现了一步法反应增容，得到共混物的扭矩、相形态、力学性能都和分步法增容共混物的结果几乎相同，这说明一步法共混能使PBT产生良好分散并得到性能较佳的产物，从而为高分子合金材料制备提供了一种简单有效的方法。 采用该方法对AA、马来酸酐(MAH)和甲基丙烯酸甘油酯(GMA)三种单体的接枝和增容反应对比研究证明，AA的效果最好，MAH次之，而GMA的效果最差，分析认为，AA和MAH通过接枝反应形成PP-g-AA和PP-g-MAH，随后再和PBT发生酯化增容反应形成PP-g-MAH-PBT共聚产物，而GMA首先和PBT反应形成PBT-GMA，而后由长链PBT-GMA发生接枝反应生成PP-g-GMA-g-PBT，但是这种接枝反应的效率很低，由此造成增容效果较差。

热可交联聚酰亚胺/高性能热塑性树脂共混体系的研究

1．热可交联聚酰亚胺／高性能热塑性树脂共混体系的研究聚苯硫醚［Poly（phenylene sulfide），PPS］是由刚性结构的苯环和柔性的硫醚连接起来，交替排列构成的线性高分子化合物，具有高的热稳定性、良好的耐化学药品性、优良的电绝缘性、耐老化性和阻燃性等综合性能优异的高性能树脂。聚醚矾〔Poly（ether sulfone），PES］是一种非结晶性的热塑性工程塑料一，具有优异的热稳定性、耐高温蠕变性及优异的物理机械性能。其高的玻璃化转变温度（Tg=225℃），使其可以在较高温度下作为结构材料使用。本论文研究了PPS/PES二元共混物的热性能和动态力学性能，并以热可控交联的低分子量多官能单体PMR-POI（聚醚酰亚胺）为界面增强剂，分别研究了POI与PPS、PES之间的接枝和／或交联反应，POI对PPS结晶行为的影响，POI对PES分子运动的影响和POI对PPS/PES共混体系的界面增强。主要结果如下：1．PPS/PES共混物相容性的特征在于选择性的部分相容，少量的非晶PPS分子可以扩散进入PES相区，相反的扩散过程则不会发生。2．PPS/PES共混物的热学性质和动态力学性能主要受连续相的控制。3．PPS相的性能主要受其结晶度的影响，因此能够改变其结晶度的因素均会改变PPS相的性质。4．光谱学和流变的证据表明，POI同PES，PPs共混过程中有接枝反应发生，分子链增长，分子量加大。这种接枝和／或交联反应的程度是热可控的。5．POI是PPS的增塑剂，成核剂和扩链剂，与POI共混使得PPS结晶速率增加，平衡熔点上升，表面折叠自由能降低。6；在PES/POI体系中Pol对PEs起到了增塑的作用，Tg降低，经高温热处理后Tg上升。因此，POI对PES性能的影响也是热可控的。7．PMR-POI能够在PPS/PES共混体系中有效地扩散并起到了降低分散相粒子的尺寸、增强界面的作用。它是该共混体系的有效界面增强剂。8．"高温退火既能够提高扩散速率也能够提高反应速率；二者相互竞争。2．马来酸配封端溉碳酸丙撑酯的研究二氧化碳与环氧丙烷交替共聚物（polypropylene careonate，PPC）是由二氧化碳活化并与环氧丙烷共聚而成的一类可完全生物降解的新型高分子材料，具有巨大的潜在应用价值。本论文讨论了马来酸配封端的聚碳酸丙撑酯（MA-PPC）和未封端的PPC的粘弹性、流变行为以及热降解和热分解行为，并得出如下结论：1．马来酸配封端抑制了PPC解拉链式的热分解和无规链断裂热降解，PPC的热稳定性和力学性能得到提高。2．PPC和MA-PPC在玻璃化转变温度有相似的自由体积分数，PPC的Tg比MA-PPC稍低。虽然PPC和MA-PPC玻璃化转变表观活化能E。和平均松弛时间T随温度升高单调降低，但PPC的分子运动对温度更敏感，而MA-PPC较稳定。马来酸配封端改变了PPC分子运动的特征及松弛行为，许多实验证据证明，这是由于封端后的PPC大分子链间的相互作用增强及分子链缠结密度增加。3．MA-PPC在70℃左右会发生脱水，实现大分子偶联反应并得到变温红外光谱、分子量成倍增加及线膨胀数据的有力支持。4．用零剪切粘度几。的方法测得PPC及MA－PPC加工过程中的热降解温度，它们分别为150℃和175℃，在此温度以上，η0降低速率的增加归因于大分子的主链断裂以及解拉链反应。5．测得了PPC的临界缠结分子量，它几乎是MA-PPC相应值（6613）的3倍。这表明马来酸配封端不仅改善了PPC的熔体弹性，而且也大大增强了PPC的缠结密度以及分子链间的相互作用。6．在本实验条件下在氮气和空气的气氛中，MA-PPC同PPC的热降解和热分解行为几乎一致，即在PPc的加土过程可以忽略氧气对其的影响。7．虽然MA-PPC的玻璃化温度在40℃左右，但在40℃-120℃的温度区间内，MA-PPC达不到粘流状态。8．没有剪切力时在120℃-150℃，30分钟内，MA-PPC几乎没有降解，在静态条件下，低于170℃时，MA-PPC的解拉链式降解是十分轻微的，当温度超过170℃，PPC降解相当严重。9．在热机械力存在的情况下，发生无规断链的机会增加，无规断链又会加速解拉链降解，因此实际加工中的加工窗口比静态下窄，MIA-PPC的加工窗口应为130℃-160℃。10．MA-PPC的热分解过程是一步完成的，热分解温度随升温速率的加快而提高，并计算出热分解的表观活化能为623.3KJ／mol。

无机刚性粒子增韧聚乙烯、聚丙烯的结构与性能研究

众所周知，聚乙烯、聚丙烯因其良好的加工性能及价格相对低廉而得到了广泛应用，但刚性和韧性的不足限制了它们在工程领域的应用。因此，提高聚乙烯、聚丙烯的刚性和韧性就成为高分子科学界和工程界一重要研究课题。本论文尝试用玻璃珠增韧聚云烯、聚丙烯，并系统研究体系的结构和性能，得到的主要结果有：1．成功实现了玻璃珠对高密度聚乙烯的增韧。在刚性、热稳定性显著提高的同时，玻璃珠增韧的高密度聚乙烯仍保持着很高的低温缺口冲击强度（-10℃，玻璃珠含量48wt％时，冲击强度为16KJ/m2）。2．得到了玻璃珠增韧高密度聚乙烯在脆韧转变点临界粒子间距（IDc）与温度的关系。这是第一条无机刚性粒子增韧热塑性聚合物体系的工Dc与温度的关系曲线。结果表明与弹性体增韧热塑性聚合物体系类似，工Dc随温度的升高而非线性增大。3．虽然没能在低温和常温下实现玻璃珠对聚丙烯的增韧，但是在较高的温度下仍发现了玻璃珠对聚丙烯有明显的增韧效果，且体系的脆韧转变温度随玻璃珠含量的增加而降低。4．用偏光显微镜（PLM）成功跟踪了所用聚丙烯p晶转变为仪晶的全过程。结果表明β晶能重结晶成以晶，重结晶生成的以晶熔点要比最初生成的a晶高五度左右。5．当聚丙烯存在两种晶型（a和β）时，实验发现聚丙烯／玻璃珠共混体系出现模量随玻璃珠含量增加先下降后上升的反常现象。进一步研究结果揭示该反常现象是玻璃珠填充和提高β晶形成能力二者竞争的结果6. 实验发现聚丙烯的β晶含量与添加玻璃珠的尺寸、含量及热处理温度有关。同样玻璃珠含量下粒子尺寸小有利于β晶的生成；对一定组成的共混物，存在一个最佳β晶形成温度。

有机碳对混合菌群亚硝酸盐氮氧化的影响

自养硝化过程在自然界氮素循环和污水处理系统脱氮过程中起着关键作用。因此，了解有机碳对硝化的影响和硝化菌与异养菌之间的竞争对微生物生态学和污水处理系统设计都很重要。目前对氨氧化到硝酸盐氮过程的研究文献很多，但对亚硝酸盐氧化过程在异养菌的存在下如何受到有机碳影响的研究甚少。本文从生理生化指标、基因组学、蛋白组学三方面考察了在实验室条件下有机碳（乙酸钠）对硝化细菌和异养菌组成的混合菌群的硝化性能、菌群结构及代谢功能的变化的影响。 全文分为两大部分： 第一部分为乙酸钠对游离态硝化混合菌群的硝化性能和菌群结构的短期影响。混合菌株先在自养条件下进行连续培养，两个月后硝化速率达到20 mg N/(L·d)；而后离心收集菌体进行批式实验。在批式反应器中，初始亚硝氮均为126mg N/ L，乙酸钠-C 与亚硝酸盐-N 的比分别为0，0.44，0.88，4.41，8.82。结果表明：在低C/N 比（0.44 和0.88）时，亚硝酸盐去除速率比C/N=0 下高，细菌呈现一次生长；而在高C/N 比（4.41 和8.82）时，出现连续的硝化反硝化，亚硝酸盐去除率仍比对照下高，细菌呈现二次生长。不同C/N 比下微生物群落明显不同，优势菌群从自养和寡营养细菌体系（包括亚硝酸盐氧化菌，拟杆菌门,α-变形菌纲,浮霉菌门和绿色非硫细菌下的一些菌株）过渡到异养和反硝化菌体系 （γ-变形菌纲的菌株尤其是反硝化菌Pseudomonas stutzeri 和P. nitroreducens 占主导）。 第二部分为乙酸钠对硝化混合菌群生物膜的硝化性能和菌群结构的长期影响。接种富集的硝化混合菌群于装有组合式填料的三角瓶中，于摇床中自养培养；两个月后填料上形成生物膜的硝化速率达到20 mg N/ (L·d)；而后进行长期实验，每12 小时更换混合营养培养基（亚硝氮约200 mg N/ L，C/N 比同上）。结果显示：相较于C/N 比=0 时的亚硝酸盐氧化反应来说，低C/N 比出现了部分的反硝化，而高C/N 比则是几乎完全的反硝化。与对照比，C/N=0.44 时亚硝酸盐氧化速率并未受乙酸钠的影响，反而上升了，但C/N=0.88 时亚硝酸盐氧化速率有所下降。菌群结构分析表明自养对照与混合营养下微生物群落的不同；PCR-DGGE未检测出混合营养下硝化杆菌的存在，而显示异养菌尤其是反硝化菌的大量存 在。荧光定量PCR 结果表明随C/N 比上升，硝化杆菌数量从2.42 × 104 下降到1.34× 103 16S rRNA gene copies/ ng DNA，反硝化菌由0 增加至2.51 × 104 nosZgene copies/ ng DNA。SDS-PAGE 的结果表明不同C/N 比下的蛋白组较为复杂且呈现一定的差异性。 有机碳对亚硝氮氧化及微生物群落的影响很复杂，本文分别讨论了对游离态和生物膜固定态两种状态的混合菌群相应的短期和长期影响研究。研究发现，有机碳并非一定带来硝化的负影响，如果控制在适当的C/N 比范围，有机碳是有利于亚硝氮氧化的。这些发现阐明了有机碳和硝化反硝化的关系，填补了硝化微生物生态学上的空白，对污水处理系统中减少异养菌的影响并提高氮去除率有一定理论指导意义。 Nitrification plays a key role in the biological removal of nitrogen in both nature and wastewater treatment plant (WWTP). So, understanding of the effect of organic carbon on nitrification and the competition between nitrifying bacteria and heterotrophic bacteria is important for both microbial ecology and WWTP design and operation. Despite the fact that the nitrification process of ammonia to nitrate has been extensively investigated, it is not known how the process of nitrite oxidization is affected by organic carbon when heterotrophic bacteria are present. By measuring different physiological and biochemical parameters, as well as using genomic DNA and proteome analysis, we investigated the influence of organic (acetate) on nitrite oxidizing performance, community structure and metabolic function of nitrite-oxidizing and heterotrophic bacteria under laboratory conditions. The dissertation involves two parts: Part one deals with the effect of organic matter on functional performance and bacterial community shift of nitrite-oxidizing and heterotrophic bacteria under suspended state. The bacteria were prepared in a continuous-flow stirred reactor under autotrophic condition; after two months, the nitrification rate of the culture reached about 20 mg N/ (L·d); then the bacteria were harvested for the next batch experiments. The initial concentrations of nitrite were 126 ± 6 mg N/ L in all flasks, and sodium acetate (C) to nitrite (N) ratios were 0, 0.44, 0.88, 4.41, and 8.82, respectively. The results showed that at low C/N ratios (0.44 or 0.88), the nitrite removal rate was higher than that obtained under autotrophic condition and the bacteria had single growth phase, while at high C/N ratios (4.41 or 8.82), continuous aerobic nitrification and denitrification occurred besides higher nitrite removal rates, and the bacteria had double growth phases. The community structure of total bacteria strikingly varied with the different C/N ratios; the dominant populations shifted from autotrophic and oligotrophic bacteria (NOB, and some strains of Bacteroidetes, Alphaproteobacteria, Actinobacteria, and green nonsulfur bacteria) to heterotrophic and denitrifying bacteria (strains of Gammaproteobacteria, especially Pseudomonas stutzeri and P. nitroreducens). Part two describes the influence of acetate on nitrite oxidizing performance, community structure and metabolic function of nitrite-oxidizing and heterotrophic bacteria in biofilms. Bacterial enrichments was transferred into flasks with polypropylene carriers and cultured under agitated and autotrophic condition. After two month, the biofilms grown on the carriers had a nitrification rate of about 20 mg N/ (L·h); then the biofilms were refreshed with mixotrophic medium (nitrite were 200 mg N/ L in all flasks, and C/N ratios was the same as above) every 12 h. the results show: normal nitrite oxidization reactions were performed when C/N = 0, but nitrite oxidization and partial denitrification occurred with low C/N ratios (0.44 or 0.88). At high C/N ratios (4.41 or 8.82), we mainly observed denitrification. In contrast to C/N = 0, the nitrite oxidization rate was unaffected when C/N = 0.44, but decreased with C/N = 0.88. The structure of bacterial communities varied significantly between autotrophic and mixotrophic conditions. Nitrobacter was hard to detect by PCR-DGGE while heterotrophs and especially denitrifiers were in the majority under mixotrophic conditions. Real-time PCR indicated that the Nitrobacter population decreased from 2.42 × 104 to 1.34 × 103 16S rRNA gene copies/ ng DNA, while the quantity of denitrifiers obviously increased from 0 to 2.51×104 nosZ gene copies/ ng DNA with an increasing C/N ratio. SDS-PAGE indicated the complexity of and a certain difference between the proteome of nitrite-oxidizing and heterotrophic bacteria at different C/N ratios. We conclude that the influence of organic matter on nitrite oxidation and the community structure of NOB and heterotrophic bacteria is complex. In this dissertation, we focused on how sodium acetate influenced the system both under suspended state and in biofilms. We observed that acetate did not necessarily have a negative impact on nitrification. Instead, an appropriate amount of acetate benefited both nitrite oxidization and denitrification. These findings provide a greater understanding about the relationship between organics and nitrification; they fill the gaps in the field of microbial ecology of nitrifying bacteria; they also provide insight into how to minimize the negative impact of heterotrophic bacteria and maximize the benefit of nitrogen removal in biological treatment systems.

Preparation of Microporous Membranes by Swift Heavy Ion Irradiation and Impedance Characterization

Polypropylene (PP) microporous membranes were successfully prepared by swift heavy ion irradiation and track-etching. Polypropylene foils were irradiated with Au-197 ions of kinetic energy 11.4 MeV.u(-1) (total energy of 2245.8 MeV) and fluence 1x10(8) ions.cm(-2) at normal incidence. The damaged regions produced by the gold ions along the trajectories were etched in H2SO4 and K2Cr2O7 solutions leading to the formation of cylindrical pores in the membranes. The pore diameters of the PP microporous membranes increased from 380 to 1610 nm as the etching time increased from 5 to 30 min. The surface and cross-section morphologies of the porous membranes were characterized by scanning electron microscopy (SEM). The micropores in the membranes were found to be cylindrical in shape, homogeneous in distribution, and equal in size. Some mathematical relations of the porosity of the PP microporous membranes were established by analytic derivation. The microporous membranes were used in lithium-ion batteries to measure their properties as separators. The electrical conductivity of the porous membrane immersed in liquid electrolyte was found to be comparable to that of commercial separators by electrochemical impedance spectroscopy (EIS). The results showed that the porosity and electrical conductivity were dependent on the ion fluence and etching time. By adjusting these two factors, microporous membranes with good porosity and electrical conductivity were made that met the requirements for commercial use.

Effect of the nucleating agent 1,3 : 2,4-di(3,4-dimethylbenzylidene) sorbitol on the gamma phase content of propylene/ethylene copolymer

The influence of the concentration of a nucleating agent (NA), namely 1,3:2,4-di(3,4-dimethylbenzylidene) sorbitol (DMDBS), on the gamma phase content in a propylene/ethylene copolymer was investigated by means of Differential Scanning Calorimetry (DSC), Wide-Angle X-ray Diffraction (WAXD), Small- Angle X-ray Scatter (SAXS) and Polarized Optical Microscopy (POM).

Preparation and properties of polyether pentaerythritol mono-maleate grafted linear low density polyethylene by reactive extrusion

A reactive type nonionic surfactant, polyether pentaerythritol mono-maleate (PPMM) was synthesized in our laboratory. PPMM was adopted as functionalizing monomer and grafted onto linear low density polyethylene (LLDPE) with a melt reactive extrusion procedure. FT-IR was used to characterize the formation of grafting copolymer and evaluate their degree of grafting. The effects of monomer concentration, reaction temperature and screw run speed on the degree of grafting were studied systematically. Isothermal crystallization kinetics of LLDPE and LLDPE-g-PPMM samples was carried out using DSC.

The investigation of exfoliation process of organic modified montmorillonite in thermoplastic polyurethane with different molecular weights

Cloisite 30B (30B) was melt-mixed with two kinds of thermoplastic polyurethane (TPU) with different molecular weights to discern the roles of molecular diffusion and shear in the exfoliation process. The higher level of exfoliation was achieved in TPU matrix with higher molecular weight due to the appropriate viscosity. In order to have an insight into the mechanism of exfoliation, the degree of dispersion and exfoliation of 30B was characterized by wide angle X-ray diffraction and transmission electron microscopy. The layers of 30B were exfoliated via a slippage process, which was also observed in polyamide 12 nanocomposites recently.

Strengthening carbon deposition of polyolefin using combined catalyst as a general method for improving fire retardancy

Combination of Ni2O3 and solid acid with Bronsted acid sites and Lewis acid sites (such as HZSM-5 and H-beta) could dramatically improve fire retardancy of polyolefin, including polypropylene and linear low-density polyethylene. This is mainly attributed to the formation of a large amount of residual char from degradation products of polyolefin in the intermediate stage of combustion. Thus, the amount of flammable components diffusing into the flame zone was small.

The new concepts and new developments in hte theory of polymer crystallization

Recently a debate about the initial crystallization process which has not been the hotspot for a long time since the theory proposed by Hoffman- Lauritzen (LH) dominated the field arose again. For a long time the Hoffman-Lauritzen model was always confronted by criticism,and some of the points were taken up and led to modifications, but the foundation remained unchanged which deemed that before the nucleation and crystallization the system was uniform. In this article the classical nucleation and growth theory of polymer crystallization was reviewed, and the confusion of the explanations to the polymer crystallization phenomenon was pointed out. LH theory assumes that the growth of lamellae is by the direct attachment of chain sequences from the melt onto smooth lateral sides.

Ethylene polymerization, and the copolymerizations of ethylene with hexene or norbornene with highly active mono(beta-enaminoketonato) vanadium(III) catalysts

Five novel vanadium(III) complexes [PhN = C(R-2)CHC(R-1)O]VCl2(THF)(2) (4a: R-1 = Ph, R-2 = CF3; 4b: R-1 =t-Bu, R-2 = CF3; 4c: R-1 = CF3, R-2 = CH3; 4d: R-1 = Ph, R-2 = CH3; 4e: R-1 = Ph, R-2 = H) have been synthesized and characterized. On activation with Et2AlCl, all the complexes, in the presence of ethyl trichloroacetate (ETA) as a promoter, are highly active precatalysts for ethylene polymerization, and produce high molecular weight and linear polymers. Catalyst activities more than 16.8 kg PE/mmolv h bar and weight-average molecular weights higher than 173 kg/ mol were observed under mild conditions.

Synthesis, structural characterization, and ethylene polymerization behavior of the vanadium(III) complexes bearing salicylaldiminato ligands

Vanadium(III) complexes bearing salicylaldiminato ligands (2a-k) [RN=CH(Ar0)]VCl2(THF)2 (Ar C61714, R = Ph, 2a; p-CF3Ph, 2b; p-CH3Ph, 2c; 2,6-Me2Ph, 2d; 2,6-iPr2Ph, 2e; cyclohexyl, 2f; Ar = C6H3tBu(2), R = Ph, 2g; 2,6-iPr2Ph, 2h; Ar = C6H2tBU2(2,4), R = Ph, 2i; 2,6-iPr2Ph, 2j; Ar = C6H2Br2, R = Ph, 2k) were prepared from VC13(THF)3 by treating with 1.0 equiv of (RN=CH)ArOH in tetrahydrofuran (THF) in the presence of excess triethylamine (TEA).

Mechanism on flame retardancy of polystyrene/clay composites-The effect of surfactants and aggregate state of organoclay

Effects of organically modified montmorillonites (OMMTs) with different type and amount of modifiers on flame retardancy of polystyrene (PS) have been studied. The results from morphology analysis, gas chromatography-mass spectrometry and cone calorimeter have showed different mechanisms for the flame retardancy of PS/OMMTs composites, depending on surface property of OMNTrs. One is the catalysis of acid sites formed on the surface of octadecylammonium modified MMT (c-MMT) via Hoffman decomposition on the carbonization of degradation products, which promotes the formation of clay-enriched char barrier.

Metal dependent control of cis-/trans-1,4 regioselectivity in 1,3-butadiene polymerization catalyzed by transition metal complexes supported by 2,6-bis[1-(iminophenyl)ethyl]pyridine

Fe(III), Cr(III), Fe(II), Co(II) and Ni(II) chloride complexes supported by 2,6-bis[1-(iminophenyl)ethyl]pyridine have been synthesized and characterized along with single crystal X-ray diffraction. These complexes, in combination with MAO, have been examined in butadiene polymerization. The catalytic activity and regioselectivity are strongly controlled by metal center and cocatalyst (MAO/Co ratio dependent in the case of Co(II) complex). The activity decreases in the order of Fe(III) > Co(II) > Cr(III) approximate to Ni (II) complexes, in consistent with the space around the metal center. Polybutadiene with different microstructure content, from high trans-1,4 units (88-95% for iron(III) and Cr(III)), medium trans-1,4 and cis-1,4 units (55% and 35%, respectively, for iron(II)) to high cis-1,4 units 79% for Co(II) and 97% for Ni(II) call be easily achieved by varying of the metal center.

Combination of Carbon Nanotubes with Ni2O3 for Simultaneously Improving the Flame Retardancy and Mechanical Properties of Polyethylene

Effects of multiwalled carbon nanotubes (MWCNTs) and Ni2O3 on the flame retardancy of linear low density polyethylene (LLDPE) have been studied. A combination of MWCNTs and Ni2O3 showed a synergistic effect in improving the flame retardancy of LLDPE compared with LLDPE composites containing MWCNTs or Ni2O3 alone. As a result, the peak value of heat release rate measured by cone calorimeter was obviously decreased in the LLDPE/MWCNTs/Ni2O3 Composites. According to the results from rheological tests, carbonization experiments, and structural characterization of residual char, the improved flame retardancy was partially attributed to the formation of a networklike structure due to the good dispersion of MWCNTs in LLDPE matrix, and partially to the carbonization of degradation products of LLDPE catalyzed by Ni catalyst originated from Ni2O3, More importantly, both viscoelastic characteristics and catalytic carbonization behavior of LLDPE/MWCNTs/Ni2O3 composites acted in concert to result in a synergistic effect in improving the flame retardancy.