Room-temperature strategy for networked nonspherical gold nanostructures from Au(III)-[G-2]-CO2H dendrimer complex

The present work describes a convenient approach to fabricate networked nonspherical gold nanostructures by using [G-2]-CO2H dendrimer and toluene as capping and bridging agents in a CH2Cl2 and H2O biphasic system. A controlled linear assembly is achieved without the use of any catalyst at room temperature. UV-vis spectrum, transmission electron microscopy (TEM), selected area electron diffraction (SAED), and X-ray diffraction (XRD) analysis show that the product is well networked nanostructures with diameter of 4-10 nm and consists of coalesced face-centered cubic gold nanocrystals. Extended experiments reveal that both benzene and dimethylbenzene can also inhabit the gold ions to make them crosslinked, prolong the nucleation points and eventually facilitate the formation of the networks.

Poly(L-lactide)/starch blends compatibilized with poly(L-lactide)-g-starch copolymer

The poly(L-lactide) (PLLA)/starch blends were prepared by the PLLA grafting starch (PLLA-g-St) copolymers as a compatibilizer, and their thermal, mechanical and morphological characterizations were performed to show the better performance of these blends compared to the virgin PLLA/starch blend without the compatibilizer, including PLLA crystallinity, interfacial adhesion between the PLLA matrix and starch dispersive phases, mechanical test, medium resistance, and contact angle. The 50/50 composite of PLLA/starch compatibilized by 10% PLLA-g-St gave a tensile strength of 24.7 MPa and an elongation at break of 8.7%, respectively, vs. 11.3 MPa and 1.5%, respectively, for the simple 50/50 blend of PLLA/starch.

PB-g-PMMA核壳粒子的合成及其在PVC中的分散

聚丁二烯(PB)橡胶粒子与聚氯乙烯(PVC)不相容。采用乳液聚合手段,在聚丁二烯乳胶粒表层接枝与聚氯乙烯相容的聚甲基丙烯酸甲酯(PMMA)充当增容剂制备了聚丁二烯接枝聚甲基丙烯酸甲酯(PB g PMMA ,MB)核壳粒子。用熔融共混法制备了PVC/MB共混物。SEM照片表明,这种核壳结构的粒子在聚氯乙烯中的分散情况随着核壳比的不同而改变,当核壳质量比小于93/7时能够完全均匀地分散在PVC基体中,核壳质量比大于94/6时根本不能分散在PVC基体中,核壳质量比为93/7是粒子能否分散开的转折点。共混物的力学性能数据表明,当MB加入量改变时,共混物也存在脆韧转变点,但受MB粒子的核壳比影响。

ABS树脂合成中影响PB-g-SAN接枝共聚物接枝率的因素

采用种子乳液聚合方式 ,以 K2 S2 O8为引发剂引发聚合 ,合成了一系列 PB- g- SAN接枝共聚物。考察了引发剂用量、分子量调节剂 (TDDM)用量和橡胶 (PB)含量对 PB- g- SAN接枝共聚物接枝率的影响。并将 K2 S2 O8引发剂与氧化 -还原引发体系做了比较。结果表明 ,随着引发剂 K2 S2 O8用量逐渐增加 ,PB- g- SAN接枝共聚物的接枝率逐渐降低。引发剂用量太少时 ,不能满足聚合要求 ,PB- g- SAN接枝共聚物的接枝率也会降低。随着分子量调节剂 (TDDM)用量的增加 ,PB- g- SAN接枝共聚物的接枝率逐渐降低。随胶含量的增加 ,PB- g- SAN接枝共聚物的接枝率逐渐降低。采用氧化 -还原引发体系引发聚合有利于接枝反应的进行 ,在 PB含量相同时 ,采用氧化 -还原引发体系合成的 PB- g- SAN接枝共聚物的接枝率比采用 K2 S2 O8合成的接枝共聚物接枝率高。

Temperature dependence of the distribution of the first passage time: Results from discontinuous molecular dynamics simulations of an all-atom model of the second beta-hairpin fragment of protein G

More than 22 000 folding kinetic simulations were performed to study the temperature dependence of the distribution of first passage time (FPT) for the folding of an all-atom Go-like model of the second beta-hairpin fragment of protein G. We find that the mean FPT (MFPT) for folding has a U (or V)-shaped dependence on the temperature with a minimum at a characteristic optimal folding temperature T-opt*. The optimal folding temperature T-opt* is located between the thermodynamic folding transition temperature and the solidification temperature based on the Lindemann criterion for the solid. Both the T-opt* and the MFPT decrease when the energy bias gap against nonnative contacts increases. The high-order moments are nearly constant when the temperature is higher than T-opt* and start to diverge when the temperature is lower than T-opt*. The distribution of FPT is close to a log-normal-like distribution at T* greater than or equal to T-opt*. At even lower temperatures, the distribution starts to develop long power-law-like tails, indicating the non-self-averaging intermittent behavior of the folding dynamics. It is demonstrated that the distribution of FPT can also be calculated reliably from the derivative of the fraction not folded (or fraction folded), a measurable quantity by routine ensemble-averaged experimental techniques at dilute protein concentrations.

Morphology and thermal and mechanical properties of PBT/HIPS and PBT/HIPS-g-GMA blends

The modification of high-impact polystyrene (HIPS) was accomplished by melt-grafting glycidyl methacrylate (GMA) on its molecular chains. Fourier transform infrared spectroscopy and electron spectroscopy for chemical analysis were used to characterize the formation of HIPS-g-GMA copolymers. The content of GMA in HIPS-g-GMA copolymer was determined by using the titration method. The effect of the concentrations of GMA and dicumyl peroxide on the degree of grafting was studied. A total of 1.9% of GMA can be grafted on HIPS. HIPS-g-GNU was used to prepare binary blends with poly(buthylene terephthalate) (PBT), and the evidence of reactions between the grafting copolymer and PBT in the blends was confirmed by scanning electron microscopy (SEM), dynamic mechanical analysis, and its mechanical properties. The SEM result showed that the domain size in PBT/HIPS-g-GMA blends was reduced significantly compared with that in PBT/HIPS blends; moreover, the improved strength was measured in PBT/HIPS-g-GMA blends and results from good interfacial adhesion. The reaction between ester groups of PBT and epoxy groups of HIPS-g-GMA can depress crystallinity and the crystal perfection of PBT.

Effect of the compatibilization of linear low-density polyethylene-g-acrylic acid on the morphology and mechanical properties of poly(butylene terephthalate)/linear low-density polyethylene blends

A poly(butylene terephthalate) (PBT)/linear low-density polyethylene (LLDPE) alloy was prepared with a reactive extrusion method, For improved compatibility of the blending system, LLDPE grafted with acrylic acid (LLDPE-g-AA) by radiation was adopted in place of plain LLDPE. The toughness and extensibility of the PBT/LLDPE-g-AA blends, as characterized by the impact strengths and elongations at break, were much improved in comparison with the toughness and extensibility of the PBT/LLDPE blends at the same compositions. However, there was not much difference in their tensile (or flexural) strengths and moduli. Scanning electron microscopy photographs showed that the domains of PBT/LLDPE-g-AA were much smaller and their dispersions were more homogeneous than the domains and dispersions of the PBT/ T,T PE blends. Compared with the related values of the PBT/LLDPE blends, the contents and melting temperatures of the usual spherulites of PBT in PBT/LLDPE-g-AA decreased.

HIPS-g-MA共聚物对HIPS/PC共混物相容性、形态和拉伸性能的影响

研究了 HIPS/ PC共混物的相容性及 HIPS- MA对 HIPS( 30 ) / PC( 70 )共混物的相容性、形态和拉伸性能的影响。DSC研究结果表明 ,HIPS/ PC共混物中 PS的玻璃化转变温度 ( Tg)不随组成而变化 ,而PC的 Tg 随其质量分数的降低逐渐向低温移动 ,说明 HIPS/ PC是部分相容体系。通过 DSC、扫描电镜形态观察和拉伸性能测试结果发现 ,当 HIPS- g- MA的含量低于 7.5 %时 ,共混物的相容性改善不明显 ,当其含量达到 7.5 %时 ,对共混物有明显的乳化作用 ,说明饱和的界面浓度在 7.5 %左右。HIPS- g- MA接枝共聚物在 HIPS( 30 ) / PC( 70 )共混物中的增容作用可能是酯交换反应原位生成的嵌段共聚物所致

Morphology, crystallization behaviors, and mechanical properties of PA1010/HIPS and PA1010/HIPS-g-MA blends

The binary blends of polyamide 1010 (PA1010) with the high-impact polystyrene (HIPS)/maleic anhydride (MA) graft copolymer (HIPS-g-MA) and with HIPS were prepared using a wide composition range. Different blend morphologies were observed by scanning electron microscopy according to the nature and content of PA1010 used. Compared with the PA1010/HIPS binary blends, the domain sizes of dispersed-phase particles in PA1010/HIPS-g-MA blends were much smaller than that in PA1010/HIPS blends at the same compositions. It was found that the tensile properties of PA1010/HIPS-g-MA blends were obviously better than that of PA 1010/HIPS blends. Wide-angle xray diffraction analyses were performed to confirm that the number of hydrogen bonds in the PA1010 phase decreased in the blends of PA1010/HIPS-g-MA. These behaviors could be attributed to the chemical interactions between the two components and good dispersion in PA1010/HIPS-g-MA blends.

Chlorohydrin water swellable rubber compatibilized by an amphiphilic craft copolymer. I. Synthesis and characterization of compatibilizer PVA-g-PBA

The graft copolymerization of butyl acrylate onto poly(vinyl alcohol) with eerie ammonium nitrate as redox initiator in a aqueous medium has been investigated. The formation of graft copolymer was confirmed by means of IR, scanning electron microscopy (SEM), and wide-angle X-ray diffraction (WAXD). The percentage of mononer conversion and percentage of grafting varied with concentrations of initiator, nitric acid, monomer, macromolecular backbone (X-n = 1750, M = 80 000), reaction temperature and reaction time. Some inorganic salts and organic solvents have a great influence upon grafting. The reaction mechanism has been explored, and rate equations for the reaction are established. (C) 2000 John Wiley & Sons, Inc.

Morphology, thermal behavior, and mechanical properties of PA6/UHMWPE blends with HDPE-g-MAH as a compatibilizing agent

A functionalized high-density polyethylene (HDPE) with maleic anhydride (MAH) was prepared using a reactive extruding method. This copolymer was used as a compatibilizer of blends of polyamide 6 (PA6) and ultrahigh molecular weight polyethylene (UHMWPE). Morphologies were examined by a scanning electron microscope. It was found that the dimension of UHMWPE and HDPE domains in the PA6 matrix decreased dramatically, compared with that of the uncompatibilized blending system. The size of the UHMWPE domains was reduced from 35 mu m (PA6/UHMWPE, 80/20) to less than 4 mu m (PA6/UHMWPE/HDPE-g-MAH, 80/20/20). The tensile strength and Izod impact strength of PA6/UHMWPE/HDPE-g-MAH (80/20/20) were 1.5 and 1.6 times as high as those of PA6/UHMWPE: (80/20), respectively. This behavior could be attributed to chemical reactions between the anhydride groups of HDPE-g-MAH and the terminal amino groups of PA6 in PA6/UHMWPE/HDPE-g-MAH blends. Thermal analysis was performed to confirm that the above chemical reactions took place during the blending process. (C) 2000 John Wiley & Sons, Inc.

LLDPE-g-AA的流变行为及力学性能

利用毛细管流变仪研究了线性低密度聚乙烯接枝丙烯酸 (LLDPE - g -AA)的流变行为。结果表明 ,在高的剪切应力下LLDPE -g -AA的表观粘度比纯LLDPE的小 ,并改进了树脂的流动性和加工性。LLDPE - g -AA的表观粘度随接枝丙烯酸含量的增加而降低 ,说明接枝到LLDPE分子链上的丙烯酸起到了内润滑剂的作用。利用Instron 112 1拉力机测试了LLDPE - g -AA的力学性能 ,结果表明其拉伸强度、杨氏模量和断裂伸长率与纯LLDPE相比没有明显的变化

实时BIA技术对蛋白A与免疫球蛋白G相互作用的研究

应用实时BIA技术 ,探讨了蛋白A与小鼠免疫球蛋白G (MIgG)之间的相互作用 ,求出相互作用的动力学速率常数ka=5 0 7× 1 0 4 (mol/L) - 1 s- 1 ,kd=9 65× 1 0 - 5(s- 1 ) ,结合常数KA=5 2 5× 1 0 8(mol/L) - 1 .同时使用蛋白A固定的传感片用于MIgG浓度的检测 ,在 0 64～ 1 2mg/L浓度区间内 ,MIgG的响应值与其浓度有非常好的线性关系.

The compatibility and morphology of HIPS/PC and HIPS-g-GMA/PC blends

The compatibility and morphology of HIPS/PC and HIPS-g-GMA/PC blends were studied. The compatibility and morphology of HIPS/PC blends were characterized by DSC and SEM, respectively. The result of DSC shows that T-g of PS doesn't change with the blend composition, and T-g of PC decreases with the increase in weight fraction of HIPS, which indicates that the PC/HIPS blend is a partially miscible system. Results of SEM indicate that the decrease in T-g of PC results from PS interpenetrating into the phase of PC, and no change in T-g of PS results from PC not interpenetrating into the phase of PS. The copolymer of HIPS-g-GMA was prepared by reactive grafting method. The IR spectrum shows that GMA is grafted on the chain of HIPS. The compatibility and morphology of HIPS-gGMA (35)/PC (65) were studied by DSC and SEM. PC (65)/HEPS-g-GMA (35) blend exhibits reduced size of disperse phase, enhanced interface adhesion and lower T-g of PC phase as compared with the PC(65)/HIPS(35) blend. It implies that HIPS-g-GMA is an effective compatibilizer of the HIPS/PC blend.