石油二次运移机理物理模拟研究

Oil and gas migration is very important for theoretical hydrocarbon geology study and exploration practice, but related research is weak. Physical simulation is a main method to study oil migration. Systematic experiments were done to quantitatively describe the migration patterns, path characters and oil saturation by adjusting the possible dynamic factors respectively. The following conclusions were drawn. 1. Darcy velocity and pore throat diameter were calculated according to seepage cross-sectional area and glass beads arrangement. With such normalized Darcy velocity and pore throat diameter, the date from one and two dimensional experiments can be reasonably drawn in two phase diagrams. It is found that the migration pattern can be identified using only one dimensionless number L which is defined as the ration of capillary number and Bond number. 2. Oil saturated in the pores between glass beads was used as calibration and oil saturation in the path was measured by magnetic resonance imaging. The results show that oil saturation in the center of migration path can reach 100%, is higher than oil saturation in the edge of migration path. 3. Percolation backbone during secondary oil migration was identified experimentally using Hele-Shaw cell. The backbone formed mainly because of the spatial variation of the cluster conductivity caused by oil saturation heterogeneity, main resistant force change, and path shrinkage and snap-off. Percolation backbone improves hydrocarbon migration efficiency and is a favorable factor for reservoir forming. 4. In the three dimensional filling models, the thickness of the secondary migration path is mall. It is only 2.5cm even for the piston pattern. Inclination of the model is the main influencing factor of the secondary path width.

裂缝型储层检测方法——P波方位各向异性技术

Nowadays, the exploration of fractured reservoir plays a vital role in the further development of petroleum industry through out the world. Fractured hydrocarbon reservoirs are widely distributed in China. Usually, S-wave technique prevails, but it also has its disadvantage, prohibitive expense in S-wave data acquisition and processing. So directly utilizing P-wave data to detect fractures, comes to our mind. We briefly introduce theoretical model (HTI) for fractured reservoir. Then study Ruger’s reflectivity method to recognize reflection P-wave reflection coefficient of the top and bottom interface of HTI layer respectively, and its azimuth anisotropy character. Base on that study, we gives a review and comparison of two seismic exploration technologies for fractures available in the industry-- P-wave AVO and AVA. They has shown great potential for application to the oil and gas prediction of fractured reservoir and the reservoir fine description．Every technique has its disadvantage, AVO limited to small reflection angle; and AVA just offering relatively results. So that, We can draw a conclusion that a better way to any particular field is using synthesis of multiple data sources including core、outcrop、well-test、image logs、3D VSPs, generally to improve the accuracy.

基于分形和统计理论的地层非均质研究

Basin-scale heterogeneity contains information about the traces of the past sedimentary cycle and tectonic process, and has been a major concern to geophysicists because of its importance in resource exploration and development. In this paper, the sonic data of 30 wells of Sulige field are used to inverse the power-law spectra slope and correlation length which are measures of the heterogeneity of the velocity of the log using fractal and statistic correlation methods. By taking the heterogeneity parameters of different wells interpolated, we get power law spectra slope and correlation length contours reflecting the stratum heterogeneity. Then using correlation and gradient, we inverse the transverse heterogeneity of Sulige field. Reservior-scale heterogeneity influnce the distribution of remaining oil and hydrocarbon accumulation. Using wavelet modulus maximum method to divide the sedimentary cycle using Gr data, therefore we can calculate the heterogeneity parameter in each layer of each log. Then we get the heterogeneity distribution of each layer of Sulige field. Finally, we analyze the relation between the signal sigularity and the strata heterogeneity, and get two different sigularity profiles in different areas.

东营凹陷幔源流体对原油生物标志化合物的影响研究

A large number of mantle-derived fluid activities occurred in the Dongying Sag. On the basis of the studies on the geochemical characteristics of these fluids in this sag, the spatial distribution of biomarkers in petroleum and their relationships with the parameters of mantle-derived fluids were studied, to reveal the influence of mantle-derived fluids on the biomarkers and to evaluate the reliability of these biomarkers when applied to oil-source correlation and maturity analysis. Most biomarkers used in oil correlation kept the characteristics of their sources during burial thermal evolution. Even some of them were not influenced by mantle derived fluids, such as the relative content of C27-C29 steroid（ααα20R）and C21/C23 tricyclic terpane. However, Pr/Ph and C35/C34 hopanes were sensitive to both heat energy and materiel input by the mantle-derived fluids. γ-waxnae/C30hopanes and C24 tetracyclic terpanes /C26 tricyclic terpanes responded only to thermal influence by mantle-derived fluids. They did not chemically reacted with the mantle-derived fluids. Fluorene series compounds reacted with hydrogen and / or carbon dioxide from the mantle. Mantle-derived fluids affected most maturity index. The huge thermal energy with mantle-devied fluids weakened the relationship between the maturity parameters and depth. Among them, pregnane/C27-29 steroid and Ts/(Ts+Tm) were more sensitive to the heat of the fluids. ααα20S/(20S+20R) took the second place. αββ/(ααα+αββ) and 22S/(22S+22R) were not thermally influenced by the mantle-derived fluid. Besides, the substance of mantle-derived fluids reacted with fragrants, hopanes or moretanoids and thus altered the values of MPI1, MPI2, MPR, C30 hopanes/(C30 hopanes + moretanoids) and alkyl-diben zothiophene/diben zothiophene. The thermal alernation of phenanthrene series and their spatial distribution show that the heat energy carried by mantle-derived fluids was not fierce but spread widely in Dongying Sag, which is favorable to hydrocarbon generation with little destroy. In sum, mantle-derived fluids affected biomarkers through thermal energy and chemical reactions and changed the values of oil-source correlation and maturity parameters in the deep-seated fault belts. Therefore, in the deep-seated fault belts, oil-source correlation should be restudied and the new parameters need to be explored.

鄂尔多斯盆地东部地区奥陶系马家沟组沉积相与储层特征研究

Ordos Basin is one of the primary bases for petroleum exploration in our country. A series of Ordovician large gas fields were discovered, which suggest that the Lower Paleozoic carbonate, especiallly for Ordovician carbonate rocks, preserve plenty of hydrocarbon resources. Well Longtong 1 is studied as the typical exploration well. Acorrding to the specific research on the type of lithology, texture, structure and sedimentary sequence in Ordovician Majiagou Formation as well as additional data from another 20 wells, the sedimentary model has been built in Majiagou Formation. The sedimentary characteristics for each Member in Majiagou Formaiton and the feature of distribution are well understood as below: It suggests that period of Member 1, Member 3 and Member 5 in Majiagou Formation characterize with dry and hot climate as well as drop of the sea level. The area of Well Longtan 1 in the eastern basin is abundant of platform evaporite lithofacies with the depositional anhyrock and salt rock, whereas yield a suite of dolomite intercalated by the thin layers of anhyrock from the anhyrcok-dolomite platform sediment. It deposits muddy dolomite, dolomitic limestone and fine-grain dolomite in limestone-dolomite platform and restricted sea. During the stage of Member 2 and Member 4 in Majiagou Formation, the climate is wet and hot with increasing sea level. The study region occurs limestone with little dolomite in the open sea environment; but the margin area is the restricted sea settings with interbeding dolomite and limestone. Based on the thin section identification, element and isotope analysis as well as the study of texture and structure, it sugguests that the main reserviors are dolomite while the gypsum are major cap rocks. The Member 2 in Majiagou Formation is both the source rocks and the resveroirs; gypsum rocks widely occur in Member 3 as the better cap; similar to the Member 2, the Member 4 in Majiagou Formation is both the source rocks and the resveroirs; there are two source-reservoir-cap assemblages in the Member 5 alone and the cap is gypsum with high quality and great thickness, which is a favorite source-reservoir-cap assemblage.

南海张裂大陆边缘数值模拟研究

The South China Sea (SCS) is one of the largest marginal seas in the western Pacific, which is located at the junction of Eurasian plate, Pacific plate and Indian-Australian plate. It was formed by continent breakup and sea-floor spreading in Cenozoic. The complicated interaction among the three major plates made tectonic movement complex and geological phenomena very rich in this area. The SCS is an ideal place to study the formation and evolution of rifted continental margin and sea-floor spreading since it is old enough to have experienced the major stages of the basin evolution but still young enough to have preserved its original nature. As the demand for energy grows day by day in our country, the deep water region of the northern continental margin in the SCS has become a focus of oil and gas exploration because of its huge hydrocarbon potential. Therefore, to study the rifted continental margin of the SCS not only can improve our understanding of the formation and evolution processes of rifted continental margin, but also can provide theoretical support for hydrocarbon exploration in rifted continental margin. This dissertation mainly includes five topics as follows: (1) Various classic lithosphere stretching models are reviewed, and the continuous non-uniform stretching model is modified to make it suitable for the case where the extension of lithopheric mantle exceeds that of the crust. Then simple/pure shear flexural cantilever model is applied to model the basement geometries of SO49-18 profile in the northern continental margin of the SCS. By fitting the basements obtained by using 2DMove software with modeling results, it is found that the reasonable effective elastic thickness is less than 5km in this region. According to this result, it is assumed that there is weak lower crust in the northern continental margin in the SCS. (2) We research on the methods for stretching factor estimation based on various lithosphere stretching models, and apply the method based on multiple finite rifting model to estimate the stretching factors of several wells and profiles in the northern continental margin of the SCS. (3) We improve one-dimension strain rate inversion method with conjugate gradient method, and apply it to invert the strain rate of several wells in the northern continental margin of the SCS. Two-dimension strain rate forward modeling is carried out, and the modeling results show that effective elastic thickness is a key parameter to control basin’s geometry. (4) We simulate divergent upwelling mantle flow model using finite difference method, and apply this newly developed model to examine the formation mechanism of the northwest and central sub-basin in the SCS. (5) We inverse plate thickness and basal temperature of oceanic lithosphere using sea-floor ages and bathymetries of the North Pacific and the North Atlantic based on varied-parameters plate model, in which the heat conductivity, heat capacity and coefficient of thermal expansion depend on temperature or depth. A new empirical formula is put forward based the inversed parameters, which depicts the relation among sea-floor age, bathymetry and heat flow. Then various similar empirical formulae, including the newly developed one, are applied to examine the sea-floor spread issue in the SCS based on the heat flow and bathymetry data of the abyssal sub-basin.

塔里木盆地寒武－奥陶系白云岩类型、成因机理及其孔隙性研究

Cambrian-Ordovician dolostones in Tarim Basin are hydrocarbon reservoir rocks of vital importance. Under the guidance of the theories of sedimentology and the sedimentology of carbonate reservoir, based on the first-hand qualitative and quantitative data especially, combined with micro-study, geochemical and reservoir capacity analysis, and precursor research, the origin and reservoir characteristics of the dolostones were discussed. Based on detailed petrographic investigations, four types of dolostone have been recognized, which are, respecitively, mud-silt-sized dolostones, algal laminated dolostones (ALD), prophyritic dolostone, and neomorphic dolostone. Mud-silt-sized dolostones always presents as laminas together with evaporated signatures, its REE patterns and ΣREE are all close to that of the finely crystalline limestone. This kind of dolomite probably experienced relatively low fluid-rock ratio during diagenesis was formed in hypersaline and oxidizing environment and involved fast dolomitization process. It was dolomitized by evaporated seawater in sabkha environment.The main primary fabrics of algal lamination in algal laminated dolomite (ALD) can still be identified and its ΣREE (21.37) is very close to that of algae. This reveals that ALD was dolomitized during early diagenesis and algae possibly played an important role. The ALD was formed under mediation of organic matter and Mg2+ were supplied by magnesium concentrated algal laminites and sea water. Prophyritic dolostones presents mainly as patchy occurrence and yield the lowest δ13C and Z value. Its ΣREE is much less than that of the finely crystalline limestone. These characteristics reveal that the cloudy cores were dolomitized in shallow early diagenetic environments by pore fluids riched in Mg2+. Whereas the clear rims were likely formed in subsequent burial into deeper subsurface environments, and the Mg2+ needed for further dolomitization possibly was supplied by the transformations of clay minerals. Neomorphic dolostones consist of coarse, turbid crystals and exhibits sucrosic and mosaic textures. It has highest Fe2+ contents and average homogeneous temperature (110.2℃). Collectively, these characteristics demonstrate that the neomorphic dolostones was likely formed by recrystallization of pre-existing dolomites during deep burial. The ΣREE of the four types of dolostone distinctly differentiates from each other. However, their REE patterns are all enriched in LREE, depleted in HREE and have Eu negative anomalies. Its ΣREE 13.64 ppm, less than 1/4 of finely crystalline limestone, and ranks the lowest in the 4 types.These characteristics are comparable to those of finely crystalline limestone, and are mainly infuenced by the sea water. These four types of dolostone show similar REE mobility behaviour and no significant fractionation, althouth they have been subjected to evidently different diageneses. Seven main pore types are identified in the dolostones , which are fenestral, moldic, intercrystal, dissolved，breccia, dissolved breccia and stylolite pores. Fenestral pores are primary and the others are secondary. The dissolved pores and intercrystal pores are the most important reservoir spaces and followed by breccias and dissolved breccia pores, and the moldic and fenestral pores are less important. Stylolites can enhance permeability of reservoir rocks in one hand, for the other hand, the capacity of reservoir and permeability are enhanced and then better reservoir rocks can be formed when they are combined with patchy dolostones. The relationship between porosity and the type of dolostones is that the dissolved neomorphic dolostones have the highest porosity of 3.65%, than followed by dissolved Mud-silt-sized dolostones of 3.35%. The mud-silt-sized dolostones without dissolution have the lowest porosity of 0.90%. Moreover, the porosity of prophyritic dolostones and the neomorphic dolostones without dissolution are lower, respectively 1.675% and 1.41%. Although algal laminated dolostones consist of euhedral crystals and riched in intercrystal pores, its porosity just yields 1.20%. The relationship between permeability and the type of dolostones is that that algal laminated dolostones have the highest permeability of 0.462mD and followed by 0.065mD of prophyritic dolostones. Dissolution have no significant influence on the permeability of neomorphic dolostones and this presented by the permeability of dissolved and non-dissolved are very close, respectively 0.043mD and 0.062mD. No matter dissolved or not, mud-silt-sized dolostones are much less permeable. The permeability of non-dissolved and dissolved are 0.051mD and 0.016mD. Collectively, in the study area, neomorphic dolostones can form high quality reservoir.

准噶尔盆地热历史与油气

Based on the temperature data from 196 wells and thermal conductivity measurements of 90 rock samples, altogether 35 heat flow data are obtained. The results show that the Junggar basin is a relatively "cold basin" at present. The thermal gradients vary between 11.6 and 26.5 ℃/km, and the thermal conductivity change from 0.17 to 3.6 W/mK. Heat flow ranges from 23.4 to 53.7 mW/m~2 with a mean of 42.3 ± 7.7 mW/m~2. The heat flow pattern shows that heat flow is higher on the uplifts and lower on the depressions. The overall low present-day heat flow in the Junggar Basin reflects its stable cratonic basement and Cenozoic tectonothermal evolution characterized by lithospheric thickening, thrust and fault at shallow crust as well as consequently quick subsidence during the Late Cenozoic. The study of the basin thermal history, which is one of the important content of the basin analysis, reveals not only the process of the basin's tectonothermal evolution, but also the thermal evolution of the source rocks based on the hydrocarbon generation models. The latter is very helpful for petroleum exploration. The thermal history of the Junggar basin has been reconstructed through the heat flow based method using the VR and Fission track data. The thermal evolutions of main source rocks (Permian and Jurassic) and the formations of the Permian and the Jurassic petroleum systems as well as the influences of thermal fields to petroleum system also have been discussed in this paper. Thermal history reconstruction derived from vitrinite reflectance data indicates that the Paleozoic formations experienced their maximum paleotemperature during Permian to Triassic with the higher paleoheat flow of around 70-85 mW/m~2 and the basin cooled down to the present low heat flow. The thermal evolution put a quite important effect on the formation and evolution of the petroleum system. The Jurassic petroleum system in the Junggar basin is quite limited in space and the source rocks of Middle-Lower Jurassic entered oli-window only along the foreland region of the North Tianshan belt, where the Jurassic is buried to the depth of 5-7 km. By contrast, the Middle-Lower Permian source rocks have initiated oil and gas generation in latter Permian to Triassic, and the major petroleum systems, like Mahu-West Pen 1 Well, was formed prior to Triassic when later Paleozoic formation reached the maximum paleotemperature.

松辽盆地南部岩性油藏成藏模式与分布规律

According to the basic geologic conditions, the paper is directed by the modem oil-gas accumulation theory and petroleum system in which typical oil pools are analyzed and the shape of lithologic trap and geologic factors are pointed out. The process during which oil and gas migrate from source rock to lithologic trap is rebuilt, and the accumulation model of oil pool is set up. With the comprehensive application of seismic geologic and log data and paying attention to the method and technology which is used to distinguish lithologic accumulation. Promising structural-lithofacies zones are got and the distribution rule of various lithologic accumulation is concluded. With making use of the biologic mark compound, different reservoirs are compared. As a result, the oil and gas in HeiDimiao come from Nenjiang Group's source rocks; in SaErTu from QingShenkou Group's and Nenjiang Group's, and in PuTaohua. GaoTaizi and FuYang from QingShankou Group's. According to the development and distribution of effective source rock, oil distribution and the comparison in the south of SongLiao basin, the characteristic of basin structure and reservoir distribution is considered, and then the middle-upper reservoir of SongLiao basin south are divided into two petroleum system and a complex petroleum system. Because of the characteristic of migration and accumulation, two petroleum systems can furtherly be divided into 6-7 sub-petroleum systems,20 sub-petroleum systems in all. As a result of the difference of the migration characteristic, accumulation conditions and the place in the petroleum system, the accumulation degree and accumulation model are different. So three accumulation mechanism and six basic accumulation model of lithologic trap are concluded. The distribution of lithologic pools is highly regular oil and gas around the generation sag distribute on favorable structural-lithofacies zones, the type of lithological pool vary regularly from the core of sandstone block to the upper zone. On the basic of regional structure and sedimentary evolution, main factors which control the form of trap are discovered, and it is the critical factor method which is used to discern the lithologic trap. After lots of exploration, 700km~2 potential trap is distinguished and 18391.86 * 10~4 tons geologic reserves is calculated. Oil-water distribution rule of pinch-out oil pool is put up on plane which is the reservoirs can be divided into four sections. This paper presented the law of distribution of oil and water in updip pinch-out reservoir, that is, hydrocarbon-bearing formation in plane can be divided into four zones: bottom edge water zone, underside oil and water zone, middle pure oil zone and above residual water zone. The site of the first well should be assigned to be middle or above pure oil zone, thus the exploration value of this type of reservoir can be recognized correctly. In accordance with the characteristics of seism and geology of low permeability thin sandstone and mudstone alternation layer, the paper applied a set of reservoir prediction technology, that is: (1)seism multi-parameter model identification; (2) using stratum's absorbing and depleting information to predict reservoir's abnormal hydrocarbon-bearing range. With the analysis of the residual resource potential and the research of two petroleum system and the accumulation model, promising objective zones are predicted scientifically. And main exploration aim is the DaRngZi bore in the west of ChangLin basin, and YingTai-SiFangZi middle-upper assembly in Honggang terrace.

塔里木盆地轮南地区三叠系油气地质模型及油气预测研究

As an important measure to understand oil and gas accumulation during petroleum exploration and development, Petroleum geological model is an integrated system of theories and methods, which includes sedimentology, reservoir geology, structural geology, petroleum geology and other geological theories, and is used to describe or predict the distribution of oil and gas. Progressive exploration and development for oil and gas is commonly used in terrestrial sedimentary basin in China for the oil and gas generation, accumulation and exploitation are very intricate. It is necessary to establish petroleum geological model, adaptive to different periods of progressive exploration and development practice. Meanwhile there is lack of an integrated system of theories and methods of petroleum geological model suitable for different exploration and development stages for oil and gas, because the current different models are intercrossed, which emphasize their different aspects. According to the characteristics of exploration and development for the Triassic oil and gas pool in Lunnan area, Tarim Basin, the Lunnan horst belt was selected as the major study object of this paper. On the basis of the study of petroleum geological model system, the petroleum geological models for different exploration and development stages are established, which could be applied to predict the distribution of oil and gas distribution. The main results are as follows. (1) The generation-accumulation and exploration-development of hydrocarbon are taken as an integrated system during the course of time, so petroleum exploration and development are closely combined. Under the guidance of some philosophical views that the whole world could be understood, the present writer realizes that any one kind of petroleum geological models can be used to predict and guide petroleum exploration and development practice. The writer do not recognize that any one kind of petroleum geological models can be viewed as sole model for guiding the petroleum exploration and development in the world. Based on the differences of extents and details of research work during various stage of exploration and development for oil and gas, the system of classification for petroleum geological models is established, which can be regarded as theoretical basis for progressive petroleum exploration and development. (2) A petroleum geological model was established based on detailed researches on the Triassic stratigraphy, structure, sedimentology and reservoir rocks in the Lunnan area, northern Tarim Basin. Some sub-belt of hydrocarbon accumulation in the Lunnan area are divided and the predominate controlling factors for oil and gas distribution in the Lunnan area are given out. (3) Geological models for Lunnan and Jiefangqudong oil fields were rebuilt by the combinations of seismology and geology, exploration and development, dynamic and static behavior, thus finding out the distribution of potential zones for oil and gas accumulations. Meanwhile Oil and gas accumulations were considered as the important unit in progressive exploration and development, and the classification was made for Lunnan Triassic pools. Petroleum geological model was created through 3D seismic fine interpretation and detailed description of characteristics of reservoir rocks and the distribution of oil and gas, especially for LN3 and LN26 well zones. The possible distribution of Triassic oil traps and their efficiency in the Lunnan area has been forecasted, and quantitative analysis for original oil(water) saturation in oil pools was performed. (4) The concept of oil cell is proposed by the writer for the first time. It represents the relatively oil-rich zones in oil pool, which were formed by the differences of fluid flows during the middle stage of reservoir development. The classification of oil cells is also given out in this paper. After the studies of physical and numerical modeling, the dominant controlling factors for the formation of various oil cells are analyzed. Oil cells are considered as the most important hydrocarbon potential zones after first recovery, which are main object of progressive development adjustment and improvement oil recovery. An example as main target of analysis was made for various oil cells of Triassic reservoir in the LN2 well area. (5) It is important and necessary that the classification of flow unit and the establishment of geological model of flow unit based on analysis of forecast for inter-well reservoir parameters connected with the statistical analysis of reservoir character of horizontal wells. With the help of self-adaptive interpolation and stochastic simulation, the geological model of flow units was built on the basis of division and correlation of flow units, with which the residual oil distribution in TIII reservoir in the LN2 well area after water flooding can be established.

柴达木盆地北缘地区油气成藏过程模拟与含油气系统评价

As an important part of petroleum exploration areas in the west of China, the north part of Qaidam basin is very promising in making great progress for petroleum discovery. But there are still many obstacles to overcome in understanding the process of petroleum formation and evaluation of oil & gas potential because of the complexity of geological evolution in the study area. Based upon the petroleum system theory, the process of petroleum formation is analyzed and the potential of oil & gas is evaluated in different petroleum systems by means of the modeling approach. The geological background for the formation of petroleum systems and the consisting elements of petroleum systems are described in detail. The thickness of strata eroded is estimated by means of vitrinite reflectance modeling, compaction parameter calculating and thickness extrapolating. The buried histories are reconstructed using the transient compaction model, which combines of forward and reverse modeling. The geo-history evolution consists of four stages - sedimentation in different rates with different areas and slow subsidence during Jurassic, uplifting and erosion during Cretaceous, fast subsidence during the early and middle periods of Tertiary, subsidence and uplifting in alternation during the late period of Tertiary and Quaternary. The thermal gradients in the study area are from 2.0 ℃/100m to 2.6 ℃/100m, and the average of heat flow is 50.6 mW/m~2. From the vitrinite reflectance and apatite fission track data, a new approach based up Adaptive Genetic Algorithms for thermal history reconstruction is presented and used to estimate the plaeo-heat flow. The results of modeling show that the heat flow decreased and the basin got cooler from Jurassic to now. Oil generation from kerogens, gas generation from kerogens and gas cracked from oil are modeled by kinetic models. The kinetic parameters are calculated from the data obtained from laboratory experiments. The evolution of source rock maturation is modeled by means of Easy %Ro method. With the reconstruction of geo-histories and thermal histories and hydrocarbon generation, the oil and gas generation intensities for lower and middle Jurassic source rocks in different time are calculated. The results suggest that the source rocks got into maturation during the time of Xiaganchaigou sedimentation. The oil & gas generation centers for lower Jurassic source rocks locate in Yikeyawuru sag, Kunteyi sag and Eboliang area. The centers of generation for middle Jurassic source rocks locate in Saishenteng faulted sag and Yuka faulted sag. With the evidence of bio-markers and isotopes of carbonates, the oil or gas in Lenghusihao, Lenghuwuhao, Nanbaxian and Mahai oilfields is from lower Jurassic source rocks, and the oil or gas in Yuka is from middle Jurassic source rocks. Based up the results of the modeling, the distribution of source rocks and occurrence of oil and gas, there should be two petroleum systems in the study area. The key moments for these two petroleum, J_1-R(!) and J_2-J_3, are at the stages of Xiaganchaigou-Shangyoushashan sedimentation and Xiayoushashan-Shizigou sedimentation. With the kinetic midels for oil generated from kerogen, gas generated from kerogen and oil cracked to gas, the amount of oil and gas generated at different time in the two petroleum systems is calculated. The cumulative amount of oil generated from kerogen, gas generated from kerogen and gas cracked from oil is 409.78 * 10~8t, 360518.40 * 10~8m~3, and 186.50 * 10~8t in J_1-R(!). The amount of oil and gas generated for accumulation is 223.28 * 10~8t and 606692.99 * 10~8m~3 in J_1-R(!). The cumulative amount of oil generated from kerogen, gas generated from kerogen and gas cracked from oil is 29.05 * 10~8t, 23025.29 * 10~8m~3 and 14.42 * 10~8t in J_2-J_3 (!). The amount of oil and gas generated for accumulation is 14.63 * 10~8t and 42055.44 * 10~8m~3 in J_2-J_3 (!). The total oil and gas potential is 9.52 * 10~8t and 1946.25 * 10~8m~3.

流体地球化学：成因、流动和流体-岩石相互作用及塔里木盆地实例研究

Geofluid in sedimentary basins is related to petroleum generation, migration, accumulation and preservation, and is a topic of geological frontier. By integrating the multi-discipline methods of petroleum geochemistry, sedimentology, hydrogeology, petroleum geology and experimental geochemistry, the thesis has carried out experiments of microcline dissolution in solutions with organic acids, crude oil, brines with high total dissolved solids (TDS), and has dealt with Al distribution between the crude oil and the brines after the experiments. Cases for study includes Central Tarim, Hetianhe Gas Field and Kucha forland basin with data containing fluid chemistry and isotopic compositions, thin sections of sandstones and carbonates, homogenization temperatures and salinities of fluid inclusions, isotopic compositions of bulk rock and autigenic minerals. The aims are to elucidate fluid origin and flow in the three areas, effect of hydrocarbon emplacement on diagenesis, and to show occurrence of microbe-mediated, and thermochemical sulfate reduction in the Tarim Basin. Microcline dissolution experiments show that after 100 hour, part of the dissolved Al distributes in the crude oil, and the Al concentrations in the crude oil rise when organic acids are added. The result can be used to explain that most oilfield waters in the Tarim Basin are characterized by less than 3mg/L Al. Crude oil added to the solutions can enhance microcline dissolution, which is also observed in the case - Silurian sandstones with early crude oil emplacement in the Central Tarim. Al and Si have higher concentrations in the experiments of oxalic acid than of acetic acid under the same pH conditions, suggesting that there exist Al-oxalate and Si-oxalate complexes. Presence of acetate can enhance the activity of Ca and Al, but Al concentrations have not been increased significantly due to formation of small Al-acetate complex during the experiments. Relationships between δD and δ~(18)O in conjunction with chemistry of oilfield waters show that the waters are evaporated connate waters, which subsequently mixed with meteoric water, and were influenced by water-rock interactions such as salt dissolution, dolomitization of calcite, albitization of feldspar. In the Hetianhe Gas Field where salt dissolution took place, δD and δ~(18)O values can be used to trace nicely meteoric water recharge area and flow direction, but TDS can not. Part of the waters have high TDS but very light δD and δ~(18)O. When combined with paleo-topography, or fluid potentials, meteoric water is suggested to flow eastward in the Hetianhe Gas Field, which is the same with the Central Tarim. Whist in the Kuche forland basin, meteoric water may have permeated Cambrian-Ordovician strata. Relationship between ~(87)Sr/~(86)Sr and 1/Sr can be used to indicate migration and mixing of brines from carbonate strata (low ~(87)Sr/~(86)Sr ratio but high Sr content), clastic strata (high ~(87)Sr/~(86)Sr ratio but low Sr content) and crystalline basement (high ~(87)Sr/~(86)Sr ratio and heavy δ~(18)O value). Using this approach, it can be found that ~(87)Sr-depleted brine from Ordovician carbonates have migrated up to and mixed with ~(87)Sr-enriched waters from Silurian and Carboniferous sandstones, and that Silurian brines have mixed with meteoric water. In the Kuche forland basin, brines from the Cambrian and Ordovician carbonates have higher ~(87)Sr/~(86)Sr ratios than those from the overlying sandstones, when combined with chemistry, δ~(15)N and ~3He/~4He ratios of the coexisting natural gases, suggesting that the brines were derived from the basement. There exists some debate on the effect of hydrocarbon emplacement on mineral diagenesis. Case-study from Silurian sandstones in the Central Tarim show that quartz has kept overgrowing secondarily when oil saturation was decreased by meteoric water flushing subsequently to hydrocarbon emplacement. Silicon precipitates on the water-wet quartz surface, leading to decreased Si concentration close to the surface. A Si grads can result in Si diffusion, which supplies Si for quartz overgrowth. Hydrocarbon oxidation-sulfate reduction is an important type of organic-inorganic interaction. Not only can it make secondary alteration of hydrocarbons, but generate H_2S and CO_2 gases which can improve reservoir property. Thermochemical sulfate reduction took place at the temperatures more than 125 ℃ to 140 ℃ in the Cambrian-Ordovician carbonates, the products - H_2S and CO_2 gases migrated up to the Silurian, and precipitated as pyrite and calcite, respectively. The pyrite has an average δ~(34)S value close to those of Ordovician seawater and anhydrite, and calcite has δ~(13)C value as low as -21.5‰. In the Hetianhe Gas Field, sulfate reduction bacteria carried by meteoric water flowing eastward may have preferentially depleted ~(12)C of light hydrocarbon gases, and results in heavier δ~(13)C values of the residual hydrocarbon gases and higher molar CO_2 in the natural gases in the west than in the east. Coexisting pyrite has δ~(34)S values as low as -24.9‰.

沾化凹陷火成岩油气藏形成条件和分布规律研究

As a kind of special lithologic ones, Igneous rock oil and gas pool is more and more paid attention, and it has different forming condition and distribution from conventional ones, such as various terrane distribution types, serious reservoir anisotropy, complicated hydrocarbon-bearing, so there is not successful experience to follow for exploration and development of this complex subtle oil and gas pool at present. For an example of Igneous oil and gas pool of Luo151 area in Zhanhua seg, Eastern China, this article study the difficult problem, including petrologic nd lithofacies analysis, Origin, invasion age and times of Igneous rock, reservoir anisotropy, Geological Modeling, Igneous reservoir synthesis evaluation. forming condition and distribution are studied synthetically, and an integrated method to predict igneous rock oil and gas pool is formed, which is evaluated by using development data. The Igneous rock is mainly diabase construction in Luo151 area of Zhanhua Sag, and petrologic types include carbonaceous slate, hornfels, and diabases. Based on analyzing synthetically petrologic component, texture and construct, 4 lithofacies zones, such as carbonaceous slate subfacies, hornfels subfacies containing cordierite and grammite, border subfacies and central subfacies, are divided in the diabase and wall rock. By studying on isotopic chronology, terrane configuration and imaging logging data, the diabase intrusion in Zhanhua Sag is formed by tholeiite magma emplacing in Shahejie formation stratum on the rift tension background Lower Tertiary in North China. The diabase intrusion of Luo151 is composed possibly of three periods magma emplacement. There is serious anisotropy in the diabase reservoirs of Luo151 in Zhanhua Sag. Fracture is primary reservoir space, which dominated by tensile fracture in high obliquity, and the fracture zones are mainly developed round joint belt of igneous rock and wall rock and position of terrane thickness changing rapidly. The generation materials of the reservoirs in Luo151 igneous oil pools consist of Intergranular micropore hornfels, condensate blowhole-solution void diabase condensate edge, the edge and center of the condensate seam diabase, of which are divided into horizontal, vertical and reticulated cracks according fracture occurrence. Based on the above research, a conceptual model of igneous rock reservoir is generated, which is vertically divided into 4 belts and horizontally 3 areas. It is built for the first time that classification evaluation pattern of igneous rock reservoir in this area, and 3 key wells are evaluated. The diabase construction is divided into grammite hornfels micropore type and diabase porous-fracture type reservoirs. The heavy mudstone layers in Third Member of Shahejie formation (Es3) provide favorable hydrocarbon source rock and cap formation, diabase and hornfels belts serve as reservoirs, faults and microcracks in the wall rocks as type pathways for oil and gas migration. The time of diabase invasion was about in the later deposition period of Dongying Formation and the middle of that of Guantao Formation, the oil generated from oil source rock of Es3 in the period of the Minghuazhen formation and is earlier more than the period of diabase oil trap and porous space forming. Based on geological and seismic data, the horizon of igneous rocks is demarcated accurately by using VSP and synthetic seismogram, and the shape distribution and continuity of igneous rocks are determined by using cross-hole seismic technology. The reservoir capability is predicted by using logging constraining inversion and neural network technology. An integrated method to predict igneous rock oil and gas pool is formed. The study is appraised by using development data. The result show the reservoir conceptual model can guide the exploration and development of oil pool, and the integrated method yielded marked results in the production.

吐合盆地鲁克沁构造带断块油藏形成机制及油藏预测

Lukeqin arc belt is a compound structure generated by multi-movements and composed of 6 sub-structural zones, which are connected by Huoyanshan Mountain. General characteristics of the arc belt are multi-patterns of structure, multi-phases for petroleum, multi-types of trap and multi-layers for reservoirs. As a part of the eastern Lukeqin arc belt located on the south of Taibei depression, Lukeqin structural zone behaves as a complex faulted-fold zone, in which the formation and distribution of hydrocarbons are controlled by structures. As the dominant source of dynamics for the second migration of hydrocarbon, structure stress field is closely related with the potentials of hydrodynamics. Results derived from the simulations of stress field by finite element method indicate that the northwest tending faults prefer seal to the northeast tending ones. The reason is that the northwest tending faults were squeezed more strongly than the northeast tending ones. Therefor, the northeast tending faults become always the paths for oil to migrate southeastward. Lukeqin structural zone is the main site for oil to concentration because it is surrounded by high stress. Situated on the front of the foreland basin of Turpan-Hami, Lukeqing arc belt is a dam to hold back the southward migrating oil from Shengbei depression. The axis line of Shenquan-Shengnan-Yanmuxi, Lukeqin and Yubei controls the migrating paths and concentrating process of oil and gas. Results derived from stress simulation and structure analyses indicate consistently that both Yubei and Lukeqin structural zones are the favorite areas for oil to migrate. The generally southward paths for oil to migrate out of Taibei depression can be two ways. One of them is from Taibei depression to Yubei structural zone and the other is from Taibei depression to Lukeqin structural zone. By the both ways, oil migrated upward along the faults and southeastward along the structural axis to concentrate in either Permian or Triassic system. The newly ascertained path for oil migration, which is accurately southeastward instead of coarsely southward, indicates the directions for further explorations on the compound Lukeqin block zone. Five kinds of seal models of fault are all found in Lukeqin block zone by studying the seal features of faults occurred in the zone. Having studied the fault seal and their controlling factors by fuzzy set method, the paper deems that the northwest tended faults are better than the northeast tended ones for oil to concentrate. The most important factors to decide the seal extent of faults in this zone are the characteristics of main stress and fluids instead of capillary pressure differences between the two sides of fault and smear mud factors. There exist seal differences not only between the faults of different time but also between the sections within a fault due to the variation of depths, strata and positions. The general distribution rules of reservoirs were dominated by the seal characteristics of a fault during the time reservoirs formed. While the current features of fault seal decide the conservation of reservoirs and heights of oil accumulations. Seal or not of a fault is not absolute because the essential for fault to seal is the distribution of permeability of fault zone. Therefor, the multi cyclical activities of faults create the space-time variation of seal features of the fault. Totally, the seal extent of the faults within the area is not as perfect as to accumulate ordinary crude. Crude oil can only be sealed when it becomes viscous. Process for crude oil to become viscous and viscous happened strongly because of the fault-fold movements. Shallowly burying and even revealing of the objective layers of the reservoirs made the crude oil to be thickened by water washing biologically degradation and oxidation degradation. The northwestward deepening during or after the reservoir formation of the structural zone provided the power for oil to migrate one or more times. The main reason for oil accumulation is the formation of Lukeqin block zone during Xishanyao stage, middle Jurassic Period, Early Yanshanian Movement. While the main reason for reservoir conservation is the placidity of Triassic blocks after the formation of reservoirs. Contrasting to former opinions, it is concluded that the reservoirs in Lukeqin zone, including viscous reservoirs, were formed by one time but not more times. So the author proposes the opinion that the reservoirs of viscous oil were formed by viscous oil migration under the conditions of aptitude sets of fault seals controlled by fluid and other factors. To grope the distribution rules outside Taibei depression and discuss the formation mechanism of Anjurassic reservoirs, it is necessary to study the dominate factors for the formation of reservoirs in Lukeqin structural zone such as structural stress, fault seals and thickening mechanism of crude oil. Also, the necessary studies are the key to break through the Taibei depression and Anjurassic systems. Therefor, they are significant for the future exploration and reserve increasing of hydrocarbon within the Turpan-Hami basin. The paper studied the distribution rules of block reservoirs and forecasted the favorable zones for further exploration in Turpan-Hami basin. Conclusions can be useful for not only the exploration in the area but also the theory consult in the adjacent areas.

南海北部大陆边缘盆地热演化史及其与油气关系

This thesis focuses on the present-day thermal field features, evolution and their connections to hydrocarbon generation of the three continental margin basins-the Yinggehai (Yingge Sea), Qiongdongnan(southeast Qiong), and Pear River Mouth basins-in northern South China Sea, based on available data from drillings, loggings, seismic cross-sections, BHTs, thermal indicators (Ro%, inclusion, etc) and geopressure measurements. After studying of present-day distribution of geothermal field and thermal disturbance of fluid in the sedimentary strata, the author discovered that the distribution of gas fields in Yinggehai Basin are closely related to the distribution of anomalously high thermal gradient area, whereas it is not the case for the Pear River Mouse Basin. And detailed processing of the fluid inclusion data indicates that geothermal fluids activated frequently in this area, and they may mainly be derived upward from the overpressure and hydrocarbon-generating beds, 3000-4500 m in depth. Therefore, the abnormal gradients in sedimentary beds were mainly caused by the active geothermal fluids related to hydrocarbon migrating and accumulating in this area. Because of the effect of overpressure retarding on vitrinite reflectance, the thermal indicators for thermal history reconstruction should be assessed before put into use. Although some factors, such as different types of kerogen, heating ratio, activities of thermal fluids and overpressure, may have effects on the vitrinite reflectance, under the circumstance that thermal fluids and overpressure co-exist, overpressure retarding is dominant. And the depth and correction method of overpressure retarding were also determined in this paper. On the basis of reviewing the methods of thermal history studies as well as existing problems, the author believes that the combination of thermal-indicator-inversion and tectono-thermal modeling is an effective method of the thermal history reconstruction for sedimentary basins. Also, a software BaTherMod for modeling thermal history of basins was successfully developed in this work. The Yinggehai Basin has been active since Tertiary, and this was obviously due to its tectonic position-the plate transition zone. Under the background of high thermal flow, long-term quick subsidence and fluid activities were the main reasons that lead to high temperature and overpressure in this basin. The Zhujiangkou Basin, a Tertiary fault-basin within the circum-Pacific tectonic realm, was tectonically controlled by the motion of the Pacific Plate and resembles the other petroliferous basins in eastern China. This basin developed early, and characterized intensive extension in the early stage and weak activity in the later stage of its development. Whereas the Qiongdongnan Basin was in a weak extension early and intensity of extension increased gradually. The relative geographical locations and the extensional histories of three basins ilustrate that the northern continental margin of South China Sea spread from south to north. On the other hand, the Qiongdongnan and Yinggehai Basins may have been controlled by the same tectonic regime since later Tertiary, whereas the Zhujiangkou Basin was not meaningfully influenced. So, the tectono-thermal evolution character of the Qiongdonnan basin should be closely to the other two. It may be concluded that the three basins have been developed within the active continental margin since Tertiary, and the local lithosphere might undergo intensive extension-perhaps two or three times of episodic extension occurred. Extension lead to large tectonoc subsidence and extreme thick Tertiary sediments for hydrocarbon generation in the basins. In response to the periodic extension of the basins, the palaeothermal flow were also periodical. The three basins all have the characteristics of multi-phase thermal evolutions that is good for oil-gas generation. And the overpressure expands the depth range of oil-gas habitat, which is meaningful to petroleum exploration in this region.