Thermal analysis of microstructural evolution of Al2O3 surface modified layers

Solidification behavior and microstructural evolution of surface modified layers in plasma cladding technique are studied via numerical simulations. Both the coupling effect of temperature and solid volume fraction are considered in the proposed thermal analytical model, by which the transient temperature distributions are calculated and the shape of melting pool is determined. Furthermore, we perform microscopic thermal analysis on the nucleation and growth behaviors of ceramic hardening phases and dendrites, as well as the kinetics of related two-phase flow systems. By comparing with experimental observations, the evolution mechanisms of the morphology of Al2O3 ceramic hardening layer are explained. Based on the above results, a relationship among the scanning velocity of plasma stream, dendritic growth rate and the advancing speed of solid/liquid interface is found, and an energy criterion is proposed for predicting the pushing/engulfing transition of ceramic particles by grain growth fronts. (C) 2009 Elsevier B.V. All rights reserved.

青藏高原东部植物生态特征在季节性雪厚度梯度上的变化

本文以青藏高原东部的高山草甸为研究对象，设置早融、中间及晚融三个融雪部位，采用实验室测量、野外测量、野外样方调查相结合的 方法，从个体、种群和群落的水平上比较研究了高山雪场植物在同一雪场样地中不同融雪梯度上的特征变异及适应，结果表明： 从早融到晚融的梯度上，随着融雪时间的逐渐推迟，表土日温差降低，冻融交替的强度减弱，土壤水份逐渐增加，总N、总P、总K 以及 可溶性的N、P 和pH 变化不明显，土壤有机质及可溶性的K 和Ca 逐渐降低。冻融交替强度上的差异以及土壤水分差异被认为是融雪梯度上 影响植物生长的主要原因。 从早融到晚融的梯度上，伴随着生态因子的改变，几种常见植物的个体特征也发生相应的变化。首先，物候期推迟。植物开始生长的时间 一般要推迟将近二十天，但同一种植物在不同的融雪部位上的衰老期趋于一致，这预示着在晚融部位同一植物的生长期要缩短。其次，个体生 长特性发生改变。黑褐穗苔草（Carex atrofusca subsp. minor (Boott) T.Koyama）和西北黄芪（Astragalus fenzelianus Pet.-Stib.）的个体生长（株高、单株叶数、单叶面积和地上生物量）表现为逐渐增加的趋势；斑唇马先蒿（Pedicularis longiflora Rudolph var. tubiformis (Klotz.) Tsoong）和川西小黄菊（Pyrethrum tatsienense (Bur. et Franch.) Ling ex Shih.）则表现为逐渐降低的趋势；长叶火绒草（Leontopodium longifolium Ling）在融雪梯度上的变化趋势不明显。再次，从繁殖特性来看，大卫马先蒿（Pedicularis davidii var. pentodon Tsoong）的单株花数、单花种子数、种子千粒重及种子萌发率随融雪的推迟呈现为逐渐增加的趋势；圆穗蓼（Polygonum macrophyllum D.Don）的种子（小坚果）千粒重和萌发率也表现为逐渐增加，其余繁殖特征变化不明显。 在种群层次上，几个常见物种的分布格局随着融雪的推迟都发生一定的变化，基本上表现为从早融的集群分布到中间或晚融部位的随机分布。物种间的联结性也发生较大的变化，由早融部位的总体上的正关联逐步过度到晚融部位上的总体上的负关联。特定种对间的联结性也发生较大的变化。恶劣环境条件（如剧烈的冻融交替）的影响以及对恶劣条件适应被认为是分布格局及种间联结性发生变化的主要原因。 在群落层次上，物种多样性的变化表现为单峰曲线的格局，即在中间部位多样性最高。早融部位强烈的冻融交替和晚融部位缩短的生长季是早融及晚融部位物种多样性不高的重要原因。几乎所有的只出现在一个融雪部位（雪深级别）上的物种都发生在中间融雪部位。这说明，中等的雪深更有利于许多高山植物的存活，而过浅过深的积雪都不利于植物的生存。另外，相距较近的融雪梯度之间的物种相似性较大，而相距较远的梯度之间物种的替代率较高，物种的相似性较小。在群落的生物量方面，地上生物量随融雪的推迟而升高，地下生物量随融雪的推迟而下降，地上与地下生物量之总和随着融雪的推迟而下降，地下生物量与地上生物量之比随着融雪的推迟而下降。早融部位的地上生物量主要集中于地上0-10cm 的范围内，表明在早融部位植物地上部分有变矮的趋势；早融部位的地下生物量在土壤各深度分布相对较均一，而晚融部位地下生物量则主要集中于地下0-10cm 的范围内。生物量的变化趋势主要与雪场中各部位的土壤水分含量及地表日温度差异有关，是植物适应特定环境的结果。 To detect the plants’ responses to snow-cover gradients in an alpine meadow of eastern Tibetan plateau, laboratory method and field sample plot method were employed, and three gradeients （early-, medium and late-melting）were established in a natural snowbed. The measurements were carried out for two years and was done on three levels——individual, population and community. The results are shown as follows : From early- to late-melting gradients, daily ground temperature difference between day and night decreased, amplitude of freeze-thaw alternation weakened, soil organic matter contents and soluble K and Ca decreased, while soil water content increased. Total N, total P, total K，pH soluble N and soluble P kept constant from early- to late-melting portions. Among these factors, the changes of intense freeze-thaw alternation and soil water contents were considered as main factors affecting plants’ growth. From early- to late-melting portions, all phenological phases postponed, e.g. phase of plant emergence postponed almost twenty days. However, the same species’ individuals at different portions withered in step, which implied that the individuals at late-melting portion possessed shorter growing season length. Along the same gradient, both Carex atrofusca subsp. minor (Boott) T. Koyama and Astragalus fenzelianus Pet.-Stib. increased their individual growth, whereas Pedicularis longiflora Rudolph var. tubiformis (Klotz.) Tsoong and Pyrethrum tatsienense (Bur. et Franch.) Ling ex Shih. decreased their individual growth. Unlike the four plants mentioned above, Leontopodium longifolium L. did not show any evident change. As to reproductive charateristics, the flowers per individual, the number of seeds per flower, the thousand seed weight and the seed germination rate of Pedicularis davidii var. pentodon showed an increasing trend; and Polygonum macrophyllum D.Don also increased its thousand seed weight and seed germination rate along the same gradient. However, the other reproductive charateristics of Polygonum macrophyllum D.Don did not change significantly. At population level, the distribution pattern of several selected species changed from cluster pattern to random pattern as the snowmelt postponed. Overall association among the species changed from positive to negative along the same gradient. Further, interspecific association also changed evidently. Adverse circumstances such as intense freeze-thaw alternation were considered as primary factors resulting in changes of population distribution pattern and interspecific association. At the level of community, species diversity showed a pattern of a unimodal trend, i.e. the highest diversity occurred at medium snow depth，perhaps because of intense freeze-thaw alternation at early-melting portions and the shortest growing season at late-melting portions. Almost all species that only appeared at one snowmelt portion occurred at medium portion, indicating that medium snow depth was more suitable for many species’ survival. Species replacement from one snowmelt portion to its neighboring portion seldom took place. However, while distance between two portions became farther, species replacement between the two portions occurred more frequently. As for biomass, aboveground biomass increased from early- to late-melting portions, whereas belowground biomass, total biomass and the ratio of belowground to aboveground all decreased along the same snow gradient. A majority of aboveground biomass distributed in a height range of 0-10 cm, suggesting that height of plants inhabiting early-melting portion be shorter compared with other portions. In addition, belowground biomass at early-melting portion was evenly distributed at different soil depth in comparison with aboveground biomass, whereas belowground biomass at late-melting portion concentrated 0-10cm soil layer below ground. The changing trend of biomass was also related to two factors. One was soil water content, and the other topsoil temperature difference between day and night.

固定化红酵母细胞合成L-苯丙氨酸研究

In this paper, bioconversion of trans-cinnamic acid(t-Ca)to L-phenylalanine (L-phe) has been investigated by using immobilized yeast cells with induced L-phe Ammonia-lyase(PAL, EC.4.3.1.5) as biocatalysts. The contents are the following. (1) Thirty strains of yeasts, including two genera (Rhodotorula, Sporobolomyces), six species (R. glutinis R. minuta,R.rubra,R.sineses,R.roseus and S.salmonicolor)were screened for their ability to converse the substrates, t-Ca and ammonia, to the product, L-phe, by using yeast cells as biocatalyst, and primary evaluation for PAL activity of the selected strains was investigated. From the results of the screening experiments, it was found that 22 strains were able to produce L-phe from t-Ca with the range of conversion yield from 2% to 67%. Studies on PAL formation time course during cultivation show that the maximum PAL activity of several different strains ranges from 2.3 to 14.4×10-3U/mg cell dry weight. The biomass of tested strains at their maximum enzyme activity is also greatly varied. (2)One of the selected strains, R. rubra as 2.166, was used for immobilized cells as biocatalysts to produce L-phe. The optimum conversion conditions and effective stablization agents were investigated. The results shown that polyacrylamide gel was chosen as a suitable matrix for immobilization of the yeast cells, and it can retain 88% of the PAL activity in the reverse direction at the following reactive conditions: [t-Ca]: 34mM. [NH4OH]: 6.OM.PH10.00, temperature: 30℃. (3) The effects of various kinds of effectors on the production of L-phe were also examined. Membrane permeabilizing agents can stimulate L-phe synthesis, but make the stability of PAL decline greatly. Polyalchoholic agents and glutamic acid were very effective for the stabilization of PAL. At the presence of glutamic acid (5%), the half life of L-phe productivity with the immobilized cells was extended to 192 hours, which was much higher than most of that having been reproted, while the half life of resting cells was only about 15 hours. (4) Use of initial velocity studies on the kinetics of enzyme-catalized reaction indicated that the apparent Km value was 13.0mM for the immobilized cells, and 4.8mM for the resting cells. Thermostability of the immobilized cells was better than the resting cells. Fluid bed bioreactor is more effective than batch bioreator in prolonging the thermostability of the biocatalysts. (5) CGA- 688 resin column chromatographic procedure was employed in the isolation and purification of L-phe, t-Ca and other substances from the reactire mixture. (6) Preparative-scale production of L-phe on a level of gram amount by immobilized cells from the culture broth of R. rubra AS2.166 allowed for the conversion yield with 30%. The characteristic physico-chemical criteria (including melting point, optical activity, elements analysis, IR, NMR) are the same with the standard L-phe. 本文报告了利用诱导的苯丙氨酸解氨酶 (PAL.EC.4.3.1.5)催化反式肉桂酸(t-Ca)氨加 成制备L-苯丙氨酸(L-phe)的研究，主要内容为：(1) 我们搜集了三十株酵母菌株，利用全细胞转化t-Ca生成L-phe的能力进行了直 接筛选，并对其PAL活性水平进行了初步评估研究。研究结果表明，其中22株酵母具有转化t-Ca生产L-phe的能力，它们包括 Rhodotorula glutinis,R.rubra, R.sineses 和Sporobolomyces roseus 的菌株，转化率在2-67%。细胞生长和PAL形成过程的研究 表明，不同菌株PAL最大活力在2.3-14.4×10-3U/mg 细胞干重，达到最大PAL活性时各株酵母的生长情况也极不一致。(2) 利用筛 选出的一株深红酵母R.rubra AS2.166 作为供试菌株，研究了细胞固定化条件下生物转化的最适条件及PAL在固定化条件下的稳定 性。结果表明以聚丙烯酰胺凝胶包埋法较为理想，能使细胞合成L-phe活力保持88%，最适t-Ca浓度为34mM，最适NH4OH浓度为6M,最 适PH10.0，最适温度45℃。(3) 多种效应物对L-phe 合成的影响研究表明：表面活性剂能刺激L-phe的合成，但使PAL稳定性下降。 多羟基化合物及Glu对PAL的稳定十分有效在有Glu存在下，能使固定化细胞合成L-phe的半寿期达192小时左右，高于大部分现已报 导的固定化结果。(4) 用初速度法研究了深红酵母AS2.166中PAL的酶促反应特征，测得固定化细胞对t-Ca的表观米氏常数Km为 13.0mM，全细胞为4.8mM，细胞固定后热稳定性提高。(5) 建立了适合低浓度分离纯化产物与底物的聚苯乙烯大孔树脂柱层析技术 ，能使L-phe与t-Ca及产物混合物中其它成分有效分开。(6) 利用固定化的R.rubra AS2.166细胞所做的制备实验能够使L-phe的产 率达到30%左右，其主要的理化指标(包括熔点、比旋光度、元素分析、IR、NMR等)与标准L-phe一致。

真菌单宁酶发酵五倍子和有机溶剂中酶法合成没食子酸丙酯的研究

本文报告了丝状真菌单宁酶发酵五倍子及有机溶剂中酶法合成没食子酸丙酯的研究。利用单宁和/或五倍子诱导丝状真菌产生单宁 酶的原理，借助二级发酵程序，对从天然源得到的75株菌进行了生物转化实验研究。选择出既能水解单宁或五倍子成没食子酸，又 能把没食子酸和丙醇合成没食子酸丙酯，而且生物催化活性都较高的1株菌，这株菌经初步鉴定为黑曲霉(Aspergillus niger No.17)。随后对它开展了产酶条件和参数优化实验，得出了最佳培养条件。立足于参数优化实验方案的基础上，经由液体培养发酵 制备单宁酶制剂，并把该酶通过化学手段共价结合到一种新型载体—聚乙烯醇和戊二醛反应生成的缩醛上，制备得到固定化单宁酶 。这种固定化生物催化剂在两种有机介质体系中都具有逆向催化合成没食子酸丙酯的能力。最后建立起来一条有效可行的微生物酶 法制备没食子酸的技术途径，没食子酸产率达到70%。对这种物质进行元素 分析：含C,49.45%;含H,3.63%。它的熔点为237℃～243 ℃，三种溶剂系统的TLC均只给出一个斑点。这些数据都与标准品一致。有机溶剂中酶法合成没食子酸丙酯的技术途径已经建立。 水溶性单宁酶在潜溶剂体系中也能催化上述酯化反应，反应混合物中的PG浓度为16.4mmol/L，制备薄层被用于分离反应混合物所含 的PG，这种产物被红外、质谱及三种溶剂系统的TLC等方法鉴定，确证为目标产物。在这一学位论文的实验研究过程中，还包括一 些生化分析方法的建立和应用，这些方法用于鉴定底物和产物及测定它们的浓度，其内容主要包括TLC定性/半定量分析、元素分析 、质谱、红外等手段的综合运用。本工作为开发我国特有的天然产物资源—五倍子的生物化工加工技术及非水相生物催化技术的开 发，提供了有用的基础数据资料，具有应用基础研究工作的重要性。In this thesis, the studies on the fermentation of Chinese gallotannin by filamentous fungi with tannase activity and enzymatic synthesis of propyl gallate(PG) in organic solvents were described through these biocatalysts. Based on the principles of induction enzyme, the tannase produced from filamentous fungi by adding tannic acid(TA) and/or Chinese gallotannin into media was investigated, and the screening experiments of bioconversion were done with 75 strains by means of a two-stage fermentation procedure. These strains were isolated with the enrichment culture technique from natural sources. Hence we selected one strain (Aspergillus niger No.17) that can not only catalyze the hydrolyses of TA and/or Chinese gallotannin into gallic acid(GA) in the liquid cultures, but also be used to synthesize PG from propanol and GA in the non-aqueous media. At the same time both of its biocatalytical activities were higher. This strain was calssified to be Aspergillus niger by the primary identification. Then optimum conditions for production of the tannase and its parameters were examined. In this way, one set of optimum culture conditions was selected. Making use of the optimum proposal, the tanase was prepared through a liquid fermentation procedure. The enzyme was convalently coupled to a new type of carrier which was made chemically from polyvinyl alcohol(PVA)and glutaraldehyde. The immobilized enzymes were able to synthesize PG reversely in two organic media. Finally, an effective enzymatic technique for production of GA was developed. The yield of GA products was up to 70%。Element analysis for this substance: calce: C, 49.42%; H, 3.56%; found: C, 49.45%, H, 3.63%. Its melting point was 237℃～ 243℃ and TLCs on three solvent systems gave only one spot respectively. These data were identical with theauthentic GA. The enzymatic synthesis of PG in organic solvents was extablished with reverse route of tannase catalytical hydrolysis. Aqueous enzyme perparation also catalyzed above esterification in a buffer system. The PG concentration in the reaction mixture was 16.4mmol/L. The reparative-scale TLC was used to isolate PG from the reaction mixture. This product separated was identified by IR, MS and TLC on three solvent systems. In this study of thesis, some biochemical analytical mehtods were developed and used to identify substrates and products, and to determinate their concentration. These methods, including TLC qualitative/half quantitative analysis, element analysis, MS, IR and so on, were useful, available and performable. This work provided basic data and information for developing the biochemical engineering and bio-processing of Chinese gallotannin-a special natural resource in China and the non-aqueous phase biocatalysis. Thus, this study possesses importance in the applied and basic research work.

A study of the suppression of the high-temperature helium embrittlement in an oxide-particle dispersion strengthened alloy

In this paper, an investigation on the micro-structure of an Fe-base oxide-dispersion-strengthened (ODS) alloy irradiated with high-energy Ne-20 ions to different doses at a temperature around 0.5T(m) (T-m is the melting point of the alloy) is presented. Investigation with the transmission electron microscopy found that the accelerated growth of voids at grain-boundaries, which is usually a concern in conventional Fe-base alloys under conditions of inert-gas implantation, was not observed in the ODS alloy irradiated even to the highest dose (12000 at.ppm Ne). The reason is ascribed to the enhanced recombination of point defects and strong trapping of Ne atoms at the interfaces of the nano-scale oxide particles in grains. The study showed that ODS alloys have good resistance to the high-temperature inter-granular embrittlement due to inert-gas accumulation, exhibiting prominence of application in harsh situations of considerable helium production at elevated temperatures like in a fusion reactor.

Research on metallic ion beam production at IMP

Since 1998, many experiments for metallic ion production have been done on LECR2 (Lanzhou ECR ion source NO.2), LECR3 (Lanzhou ECR ion source NO.3) and SECRAL (Superconductiong ECR ion source Advanced design in Lanzhou) at Institute of Modern Physics. The very heavy metallic ion beams such as those of uranium were also produced by the plasma sputtering method, and supplied for HIRFL (Heavy Ion Research Facility in Lanzhou) accelerators successfully. During the test, 11.5e mu AU(28+), 9e mu AU(24+) were obtained. Some ion beams of the metal having lower melting temperature such as Ni and Mg ion beams were produced by oven method on LECR3 too. The consumption rate was controlled to be lower for Mg-26 ion beams production, and the minimum consumption was about 0.3mg per hour. In this paper, the main experimental results are given. Some discussions are made for some experimental phenomena and results, and some conclusions are drawn.

Calorimetric study on two biphenyl liquid crystals

The molar heat capacities of the two biphenyl liquid crystals, 3BmFF and 3BmFFXF3, with a purity of 99.7 mol% have been precisely measured by a fully automated precision adiabatic calorimeter in the temperature range between T = 80 and 350 K. Nematic phase-liquid phase transitions were found between T = 297 K and 300 K with a peak temperature of T-peak = (298.071 +/- 0.089) K for 3BmFF, and between T = 316 and 319 K with a peak temperature of T-peak = (315.543 +/- 0.043) K for 3BmFFXF3. The molar enthalpy (Delta(trs)H(m)) and entropy (Delta(trs)S(m)) corresponding to these phase transitions have been determined by means of the analysis of the heat capacity curves, which are (15.261 +/- 0.023) U mol(-1) and (51.202 +/- 0.076) J K-1 mol(-1) for 3BmFF, (31.624 +/- 0.066) kJ mol(-1) and (100.249 +/- 0.212) J K-1 mol(-1) for 3BmFFXF3, respectively. The real melting points (TI) and the ideal melting points (TO) with no impurities of the two compounds have been obtained from the fractional melting method to be (298.056 +/- 0.018) K and (298.165 +/- 0.038) K for 3BmFF, (315.585 +/- 0.043) K and (315.661 +/- 0.044) K for 3BmFFXF3, respectively. In addition, the transitions of these two biphenyl liquid crystals from nematic phase to liquid phase have further been investigated by differential scanning calorimeter (DSC) technique; the repeatability and reliability for these phase transitions were verified. (C) 2004 Elsevier B.V. All rights reserved.

Thermochemical and thermal analysis on N-(p-methylphenyl)-N '-(2-pyridyl)urea

Low temperature heat capacities of N-(p-methylphenyl)-N'-(2-pyridyl)urea were determined by adiabatic calorimetry method in the temperature range from 80 to 370 K. It was found that there was not any heat anomaly in this temperature region. Based on the experimental data, some thermodynamic function results were obtained. Thermal stability and decomposition characteristics analysis of N-(p-methylphenyl)-N'-(2-pyridyl)urea were carried out by DSC and TG. The results indicated that N-(p-methylphenyl)-N'-(2-pyridyl)urea started to melt at ca. 426 K (153degreesC) and the melting peak located at 447.01 K (173.86degreesC). The melting enthalpy was 204.445 kJ mol(-1) (899.6 J g(-1)). The decomposition peak of N-(p-methylphenyl)-N'-(2-pyridyl)urea was found at 499.26 K (226.11degreesC) from DSC curve. This result was similar with that from TG and DTG experiment, in which the mass loss peak was determined as 500.4 K (227.2degreesC).

Low-temperature heat capacities and derived thermodynamic functions of cyclohexane

The low-temperature heat capacities of cyclohexane were measured in the temperature range from 78 to 350 K by means of an automatic adiabatic calorimeter equipped with a new sample container adapted to measure heat capacities of liquids. The sample container was described in detail. The performance of this calorimetric apparatus was evaluated by heat capacity measurements on water. The deviations of experimental heat capacities from the corresponding smoothed values lie within +/-0.3%, while the inaccuracy is within +/-0.4%, compared with the reference data in the whole experimental temperature range. Two kinds of phase transitions were found at 186.065 and 279.684 K corresponding solid-solid and solid-liquid phase transitions, respectively. The entropy and enthalpy of the phase transition, as well as the thermodynamic functions {H-(T)- H-298.15 K} and {S-(T)-S-298.15 K}, were derived from the heat capacity data. The mass fraction purity of cyclohexane sample used in the present calorimetric study was determined to be 99.9965% by fraction melting approach.

Heat capacities and thermodynamic properties of chrysanthemic acid

The heat capacities of chrysanthemic acid in the temperature range from 80 to 400 K were measured with a precise automatic adiabatic calorimeter. The chrysanthemic acid sample was prepared with the purity of 0.9855 mole fraction. A solid-liquid fusion phase transition was observed in the experimental temperature range. The melting point, T-m, enthalpy and entropy of fusion, Delta(fus)H(m), Delta(fus)S(m), were determined to be 390.741 +/- 0.002 K, 14.51 +/- 0.13 kJ mol(-1), 37.13 +/- 0.34 J mol(-1) K-1, respectively. The thermodynamic functions of chrysanthemic acid, H-(T)-H-(298.15), S-(T)-S-(298.15) and G((T))-G((298.15)) were reported with a temperature interval of 5 K. The TG analysis under the heating rate of 10 K min(-1) confirmed that the thermal decomposition of the sample starts at ca. 410 K and terminates at ca. 471 K. The maximum decomposition rate was obtained at 466 K. The purity of the sample was determined by a fractional melting method.

Heat capacity and thermodynamic properties of pyrimethanil myristic salt (C26H41N3O2)

Pyrimethanil myristic salt was synthesized and its heat capacities were measured with an automated adiabatic calorimeter over the temperature range from T = (79 to 360) K. The melting point, molar enthalpy, Delta(fus)H(m) and entropy, Delta(fus)S(m), of fusion of this compound were determined to be (321.84 +/- 0.05) K, (56.53 +/- 0.03) kJ . mol(-1) and (175.64 +/- 0.05) J . mol(-1) . K-1, respectively. The purity of the compound was calculated to be 98.99 mol% by using the fractional melting technique. The thermodynamic functions relative to the reference temperature, T = 298.15 K, were calculated based on the heat capacity measurements in the temperature ranges from T = (80 to 360) K. The TG-DTG results demonstrate that the mass loss of the sample takes place in one step with the maximum rate at T = 500 K, which was caused by evaporation of the sample. (C) 2004 Elsevier Ltd. All rights reserved.

Heat capacity and thermodynamic properties of crystalline ornidazole (C7H10ClN3O3)

The molar heat capacities of 1-(2-hydroxy-3-chloropropyl)-2-methyl-5-nitroimidazole (Ornidazole) (C7H10CIN3O3) with purity of 99.72mol% were measured with an adiabatic calorimeter in the temperature range between 79 and 380K. The melting-point temperature, molar enthalpy Delta(fus)H(m), and entropy, Delta(fus)S(m), of fusion of this compound were determined to be 358.59 +/- 0.04K, 21.38 +/- 0.02 kJ mol(-1) and 59.61 +/- 0.05 J K-1 mol(-1), respectively, from fractional melting experiments. The thermodynamic function data relative to the reference temperature (298.15 K) were calculated based on the heat capacities measurements in the temperature range from 80 to 380 K. The thermal stability of the compound was further investigated by DSC and TG. From the DSC curve an intensive exothermic peak assigned to the thermal decomposition of the compound was observed in the range of 445-590 K with the peak temperature of 505 K. Subsequently, a slow exothermic effect appears when the temperature is higher than 590 K, which is probably due to the further decomposition of the compound. The TG curve indicates the mass loss of the sample starts at about 440K, which corresponds to the decomposition of the sample. (C) 2003 Elsevier B.V. All rights reserved.

Thermodynamic studies of monuron

Monuron (C9H11ClN2O; N,N-dimethyl-N'-(4-chlorophenyl) urea, CAS 150-68-5) was synthesized and the heat capacities of the compound were measured in the temperature range from 79 to 385 K with a high precision automated adiabatic calorimeter. No phase transition or thermal anomaly was observed in this range. The enthalpy and entropy data of the compound relative to the reference temperature 298.15 K were derived based on the heat capacity data. The thermodynamic properties of the compound were further investigated through DSC and TG analysis. The melting point, the molar enthalpy, and entropy of fusion were determined to be 447.6 +/- 0.1 K, 29.3 +/- 0.2 kJ mol(-1), and 65.4 J K-1 mol(-1), respectively. (C) 2004 Elsevier B.V. All rights reserved.

Heat capacity and enthalpy of fusion of penconazole (C13H15C12N3)

Low-temperature heat capacities of penconazole (C13H15Cl2N3) were precisely measured with an automated adiabatic calorimeter over the temperature rang from 78 to 364 K. The sample was observed to melt at 332.38 +/- 0.06 K. The molar enthalpy and entropy of fusion of the compound were determined to be 33580 +/- 11 J mol(-1), 101.03 +/- 0.02 J mol(-1) K-1, respectively. Further research of the melting process for this compound was carried out by means of differential scanning calorimetry (DSC) technique. The result was in agreement with that obtained from the measurements of heat capacities. (C) 2003 Elsevier B.V. All rights reserved.

Low-temperature heat capacity and thermodynamic properties of crystalline carboxin (C12H13NO2S)

Carboxin was synthesized and its heat capacities were measured with an automated adiabatic calorimeter over the temperature range from 79 to 380K. The melting point, molar enthalpy (Delta(fus)H(m)) and entropy (Delta(fus)S(m)) of fusion of this compound were determined to be 365.29 +/- 0.06K, 28.193 +/- 0.09 kJ mol(-1) and 77.180 +/- 0.02 J mol(-1) K-1, respectively. The purity of the compound was determined to be 99.55 mol% by using the fractional melting technique. The thermodynamic functions relative to the reference temperature (298.15 K) were calculated based on the heat capacity measurements in the temperature range between 80 and 360 K. The thermal stability of the compound was further investigated by differential scanning calorimetry (DSC) and thermogravimetric (TG) analysis. The DSC curve indicates that the sample starts to decompose at ca. 290degreesC with the peak temperature at 292.7degreesC. The TG-DTG results demonstrate the maximum mass loss rate occurs at 293degreesC corresponding to the maximum decomposition rate. (C) 2003 Elsevier B.V All rights reserved.