Mixed-mode fracture mechanisms near the fatigue threshold of aisi-316 stainless-steel

Near threshold, mixed mode (I and II), fatigue crack growth occurs mainly by two mechanisms, coplanar (or shear) mode and branch (or tensile) mode. For a constant ratio of ΔK_I/ΔK_II the shear mode growth shows a self-arrest character and it would only start again when ΔK_I and ΔK_II are increased. Both shear crack growth and the early stages of tensile crack growth, are of a crystallographic nature; the fatigue crack proceeds along slip planes or grain boundaries. The appearance of the fracture surfaces suggest that the mechanism of crack extension is by developing slip band microcracks which join up to form a macrocrack. This process is thought to be assisted by the nature of the plastic deformation within the reversed plastic zone where high back stresses are set up by dislocation pile-ups against grain boundaries. The interaction of the crack tip stress field with that of the dislocation pile-ups leads to the formation of slip band microcracks and subsequent crack extension. The change from shear mode to tensile mode growth probably occurs when the maximum tensile stress and the microcrack density in the maximum tensile plane direction attain critical values.

氢对锆基块体非晶合金形变和开裂的影响

通过充氢和未充氢缺口拉伸试样和三点弯曲试样在SEM下的原位加载,研究了氢对Zr65Al7.5Ni10Cu17．5块体非晶合金形变和开裂过程的影响．结果表明,无论是否有氢,块体非晶的剪切带发展到临界尺寸,剪切裂纹就沿剪切带形核、扩展,它一旦张开就导致快速的断裂．断口边缘观察到的无特征区是剪切带,而不是剪切裂纹断口;剪切断口形貌和拉伸断口形貌没有本质区别．只有当长时间充氢才能形成氢鼓泡,如鼓泡很小或尚未形成,则氢对剪切带以及裂纹的形核、扩展没有明显影响;如存在较大的氢鼓泡,则当剪切带尚未充分发展时微裂纹就形核,导致低应力脆断．

涂层断裂韧性的声发射辅助拉伸测量方法

涂层的断裂韧性与界面结合强度是表征涂层/基体材料体系力学性能的重要指标.但如何准确地测量涂层的断裂韧性和强界面结合的涂层/基体材料体系的界面结合强度至今仍存在困难.以铬涂层/钢基体材料为对象,采用声发射和显微镜实时动态检测技术与拉伸实验相结合的方法,探索了铬涂层的断裂韧性以及铬涂层/钢基体的界面剪切强度.根据相关力学模型和实验测量结果,得到铬涂层在室温下的断裂韧性为27.41J/m~2. 同时,发现在铬涂层裂纹饱和后界面开裂都未发生,获得了该种材料体系界面剪切强度的一个下限值.

考虑刚度及边界条件的索力精确求解

目前索力的测试大多不考虑结构刚度的影响，这导致测试的结果偏大。本文中不仅考虑了索的刚度，而且将索的边界条件假定为简支以及简支和固支耦合两种情况，得到不同假设下的理论公式，分析了不同方法下索力的区别，并利用实测的数据进行分析，给出了末考虑刚度情况下和仅考虑为简支时的误差，证明在索力测试中，特别是短索的测试中，特别是短索的测试中刚度以及边界条件考虑的必要性。

YAG激光毛化技术进展

二十世纪八十年代，当比利时冶金研究中心(CRM)开发出CO_2激光毛化冷轧辊技术后，尝试用YAG激光进行轧辊毛化一直吸引着众多的研究者，这是因为YAG(1.06μm)激光波长比CO_2(10.6μm)激光波长短一个量级，材料对YAG激光有更高的吸收率，并用YAG激光可以聚焦到更小的光斑尺寸，同时使用电信号驱动的声光开关技术便于对毛化分布进行可设定控制。但是用传统声光调制的YAG激光虽然可以碇以很高的脉冲频率(>30kHz)，但单脉冲有量仅为10mJ左右，难以达到辊面毛化粗糙度的要求，因此人们认为YAG激光用于毛化的主要困难是脉冲能量太小。

Numeric Calculation for Transient Thermal Stress Field in Wall-Shape Metal Part During Laser Direct Forming

In order to investigate the transient thermal stress field in wall-shape metal part during laser direct forming, a FEM model basing on ANSYS is established, and its algorithm is also dealt with. Calculation results show that while the wall-shape metal part is being deposited, in X direction, the thermal stress in the top layer of the wall-shape metal part is tensile stress and in the inner of the wall-shape metal part is compressive stress. The reason causing above-mentioned thermal stress status in the wall-shape metal part is illustrated, and the influence of the time and the processing parameters on the thermal stress field in wall-shape metal part is also studied. The calculation results are consistent with experimental results in tendency.

“Deborah Numbers”, Coupling Multiple Space and Time Scales and Governing Damage Evolution to Failure

Two different spatial levels are involved concerning damage accumulation to eventual failure. nucleation and growth rates of microdamage nN* and V*. It is found that the trans-scale length ratio c*/L does not directly affect the process. Instead, two independent dimensionless numbers: the trans-scale one * * ( V*)including the * **5 * N c V including mesoscopic parameters only, play the key role in the process of damage accumulation to failure. The above implies that there are three time scales involved in the process: the macroscopic imposed time scale tim = /a and two meso-scopic time scales, nucleation and growth of damage, (* *4) N N t =1 n c and tV=c*/V*. Clearly, the dimensionless number De*=tV/tim refers to the ratio of microdamage growth time scale over the macroscopically imposed time scale. So, analogous to the definition of Deborah number as the ratio of relaxation time over external one in rheology. Let De be the imposed Deborah number while De represents the competition and coupling between the microdamage growth and the macroscopically imposed wave loading. In stress-wave induced tensile failure (spallation) De* < 1, this means that microdamage has enough time to grow during the macroscopic wave loading. Thus, the microdamage growth appears to be the predominate mechanism governing the failure. Moreover, the dimensionless number D* = tV/tN characterizes the ratio of two intrinsic mesoscopic time scales: growth over nucleation. Similarly let D be the “intrinsic Deborah number”. Both time scales are relevant to intrinsic relaxation rather than imposed one. Furthermore, the intrinsic Deborah number D* implies a certain characteristic damage. In particular, it is derived that D* is a proper indicator of macroscopic critical damage to damage localization, like D* ∼ (10–3~10–2) in spallation. More importantly, we found that this small intrinsic Deborah number D* indicates the energy partition of microdamage dissipation over bulk plastic work. This explains why spallation can not be formulated by macroscopic energy criterion and must be treated by multi-scale analysis.

The Effect of the Thickness of Fe2 Al5 Phase Layer at Fe/Al Interface on the Mechanics Behavior of Hot Dip Aluminizing Coating

Hot Dip Aluminized Coatings with different thickness were prepared on Q235 steel in aluminum solutions with different temperature for certain time. Through tensile tests and in-situ SEM observations, the effect of the coating's microstructure on the tensile strength of the samples was studied. It was disclosed at certain aluminum solution temperature,transaction layers mainly composed of Fe2 Al5 phase got thicker with time prolonging, and this changed initial crack's extending direction from parallel with to vertical with stretching direction. The change in crack direction decreased tensile strength of samples, thus made the coating easy to break. It was concluded that the existence of thick Fe2 Al5 phase layer was the basic reason for the lowering of tensile strength of the coating.

Investigation on the Interaction of Laser Beam and Metal Powders Conveyed by Coaxial Powder Feeder

In order to investigate the transient thermal stress field in wall-shape metal part during laser direct forming, a FEM model basing on ANSYS is established, and its algorithm is also dealt with. Calculation results show that while the wall-shape metal part is being deposited, in X direction, the thermal stress in the top layer of the wall-shape metal part is tensile stress and in the inner of the wall-shape metal part is compressive stress. The reason causing above-mentioned thermal stress status in the wall-shape metal part is illustrated, and the influence of the time and the processing parameters on the thermal stress field in wall-shape metal part is also studied. The calculation results are consistent with experimental results in tendency.

Determination of plastic properties by instrumented spherical indentation: Expanding cavity model and similarity solution approach

The present paper aims to develop a robust spherical indentation-based method to extract material plastic properties. For this purpose, a new consideration of-piling-up effect is incorporated into the expanding cavity model; an extensive numerical study on the similarity Solution has also been performed. As a consequence, two semi-theoretical relations between the indentation response and material plastic properties are derived, with which plastic properties of materials can be identified from a single instrumented spherical indentation curve, the advantage being that this approach no longer needs estimations of contact radius with given elastic modulus. Moreover, the inconvenience in using multiple indenters with different tip angles can be avoided. Comprehensive sensitivity analyses show that the present algorithm is reliable. Also, by experimental verification performed oil three typical materials, good agreement of the material properties between those obtained from the reverse algorithm and experimental data is obtained.

Torsion fracture behavior of drawn pearlitic steel wires with different heat treatments

In this paper, torsion fracture behavior of drawn pearlitic steel wires with different heat treatments was investigated. Samples with different heat treatments was investigated. Samples with different heat treatment conditions were subjected to torsion and tensile tests. The shear strain along the torsion sample after fracture was measured. Fracture surface of wires was examined by Scanning Electron Microscopy. In addition, the method of Differential Scanning Calorimetry was used to characterize the thermodynamic process in the heat treatment. A numerical simulation via finite element method on temperature field evolution for the wire during heat treatment process was performed. The results show that both strain aging and recovery process occur in the material within the temperature range between room temperature and 435 degrees C. It was shown that the ductility measured by the number of twists drops at short heating times and recovers after further heating in the lead bath of 435 degrees C. On the other hand, the strenght of the wire increases at short heating times and decreases after further heating. The microstructure inhomogeneity due to short period of heat treatment, coupled with the gradient characteristics of shear deformation during torsion results in localized shear deformation of the wire. In this situation, shear cracks nucleate between lamella and the wire breaks with low number of twists.

固体力学进展及应用: 庆贺李敏华院士90华诞文集

《固体力学进展及应用：庆贺李敏华院士90华诞文集》收录了近代固体力学基础理论及其应用领域的重要科技成果和最新进展。作者是在同体力学领域工作多年的资深研究员，他们来自各行各业，有丰富的科研与丁作经验。他们提供的论文在相当程度上反映当前同体力学的发展现状与成就，并能看出发展趋势，对未来研究的课题选择有参考价值。《固体力学进展及应用：庆贺李敏华院士90华诞文集》还收集了李敏华院士的珍贵照片和纪念李敏华院士90华诞的庆贺和回忆文章，具有重要的史料价值。

Atomistic Simulation On Size-Dependent Yield Strength And Defects Evolution Of Metal Nanowires

A simple derivation based on continuum mechanics is given, which shows the surface stress is critical for yield strength at ultra-small scales. Molecular dynamics (MD) simulations with modified embedded atom method (MEAM) are employed to investigate the mechanical behaviors of single-crystalline metal nanowires under tensile loading. The calculated yield strengths increasing with the decrease of the cross-sectional area of the nanowires are in accordance with the theoretical prediction. Reorientation induced by stacking faults is observed at the nanowire edge. In addition. the mechanism of yielding is discussed in details based on the snapshots of defects evolution. The nanowires in different crystallographic orientations behave differently in stretching deformation. This study on the plastic properties of metal nanowires will be helpful to further understanding of the mechanical properties of nanomaterials. (C) 2009 Elsevier B.V. All rights reserved.

Determination Of Plastic Properties By Instrumented Spherical Indentation: Expanding Cavity Model And Similarity Solution Approach

The present paper aims to develop a robust spherical indentation-based method to extract material plastic properties. For this purpose, a new consideration of-piling-up effect is incorporated into the expanding cavity model; an extensive numerical study on the similarity Solution has also been performed. As a consequence, two semi-theoretical relations between the indentation response and material plastic properties are derived, with which plastic properties of materials can be identified from a single instrumented spherical indentation curve, the advantage being that this approach no longer needs estimations of contact radius with given elastic modulus. Moreover, the inconvenience in using multiple indenters with different tip angles can be avoided. Comprehensive sensitivity analyses show that the present algorithm is reliable. Also, by experimental verification performed oil three typical materials, good agreement of the material properties between those obtained from the reverse algorithm and experimental data is obtained.

Shape effects on the yield stress and deformation of silicon nanowires: A molecular dynamics simulation

The tension and compression of single-crystalline silicon nanowires (SiNWs) with different cross-sectional shapes are studied systematically using molecular dynamics simulation. The shape effects on the yield stresses are characterized. For the same surface to volume ratio, the circular cross-sectional SiNWs are stronger than the square cross-sectional ones under tensile loading, but reverse happens in compressive loading. With the atoms colored by least-squares atomic local shear strain, the deformation processes reveal that the failure modes of incipient yielding are dependent on the loading directions. The SiNWs under tensile loading slip in {111} surfaces, while the compressive loading leads the SiNWs to slip in the {110} surfaces. The present results are expected to contribute to the design of the silicon devices in nanosystems.