Effects of the frequency chirp on the fields of a chirped Gaussian pulse passing through a hard-edged aperture

Based on the Huygens-Fresnel diffraction integral and Fourier transform, propagation expression of a chirped Gaussian pulse passing through a hard-edged aperture is derived. Intensity distributions of the pulse with different frequency chirp in the near-field and far-field are analyzed in detail by numerical calculations. In the near-field, amplitudes of the intensity peaks generated by the modulation of the hard-edged aperture decrease with increasing the frequency chirp, which results in the improving of the beam uniformity. A physical explanation for the smoothing effect brought by increasing the frequency chirp is given. The smoothing effect is achieved not only in the pulse with Gaussian transverse profile but also in the pulse with Hermite-Gaussian transverse profile when the frequency chirp increases. (C) 2005 Elsevier B.V. All rights reserved.

Smoothing effect in the broadband laser through a dispersive wedge

The propagation expression of a broadband laser passing through a dispersive wedge is derived on the basis of the Huygens-Fresnel diffraction integral, Smoothing effects caused by the phase perturbation of the dispersive wedge on the intensity profiles are investigated in detail. The phase perturbation of the dispersive wedge induces a relative transverse position shift between the diffraction patterns of different frequency components. The relative transverse position shift is of great benefit to the fill of the intensity peaks of some patterns in the valleys of others when these patterns are overlapped and thus the smoothing effect is achieved. (c) 2006 Elsevier B.V. All rights reserved.

厄米-高斯光束中带宽对横向强度分布均匀性的影响

使用惠更斯-菲涅耳衍射积分和傅里叶变换，推导了横向模式为厄米高斯的激光束通过硬边光阑的传输表达式。利用所得公式通过数值计算详细分析了光束的频带宽度对光束横向强度分布的影响。分析发现激光束通过硬边光阑后会出现大量的强度尖峰，引起近场的强度分布不均匀。然而，当带宽增加时，强度尖峰的数量减少，幅度减小，光束的均匀性得到改善。在远场，光束的横向强度分布没有强度尖峰出现，但宽度随带宽的增加而减小。因此带宽增加会带来近场强度匀滑化和远场光束宽度变窄的效应。另外，数值结果表明带宽对模指数为1和2的厄米-高斯光束的强度分

Subwavelength imaging with two symmetrical interfaces by dielectric-tube photonic crystals

As distinct from coated photonic crystals, in this paper we propose a novel one that is made of dielectric tubes arranged in a close-packet square lattice. Without metallic cores, this structure is low-loss and convenient to fabricate. A left-handed frequency region is found in the second band by dispersion characteristic analysis. Without inactive modes for the transverse electric mode, negative refraction and subwavelength imaging are demonstrated by the finite-difference time-domain simulations with two symmetrical interfaces, i.e. Gamma X and Gamma M.

The analytical description and experiments of the optical bottle generated by an axicon and a lens

Based on the interferential theory, we deduce a new type of analytic expression suitable for describing the evolutions of the optical bottle beam generated from the axicon-lens optical system illuminated by the Gaussian beam for the first time. The theory does not use much approximation in the process of mathematical analysis and can better illustrate the optical bottle beam evolutions at any positions. With the derived expression, the three-dimensional (3D) longitudinal and transverse intensity profiles of the optical bottle beam are simulated numerically. The numerical calculations have been confirmed by the experimental results.

Electromagnetic fields and transmission properties in tapered hollow metallic waveguides

We analyze the electromagnetic spatital distributions and address an important issue of the transmission properties of spherical transverse-electric (TE) and transverse-magnetic (TM) eigenmodes within a tapered hollow metallic waveguide in detail. Explicit analytical expressions for the spatital distributions of electromagnetic field components, attenuation constant, phase constant and wave impedance are derived. Accurate eigenvalues obtained numerically are used to study the dependences of the transmission properties on the taper angle, the mode as well as the length of the waveguide. It is shown that all modes run continuously from a propagating through a transition to an evanescent region and the value of the attenuation increases as the distance from the cone vertex and the cone angle decrease. A strict distinction between pure propagating and pure evanescent modes cannot be achieved. One mode after the other reaches cutoff in the tapered hollow metallic waveguide as the distance from the cone vertex desreases. (C) 2008 Optical Society of America

Spatiotemporal behaviors and singularity of ultrashort pulsed Elegant Hermite-Gaussian beams

Analytical propagation expressions of ultrashort pulsed Elegant Hermite-Gaussian beams are derived and spatiotemporal properties of the pulses with different transverse modes are studied. Singularity of the complex amplitude envelope solution of the pulses obtained under slowly varying envelope approximation is analyzed in detail. The rigorous analytical solution of the pulse is deduced and no singularity emerges in the solution. The obtained results indicate that the transverse mode affects not only the spatiotemporal properties but also the singularity of the pulses. Time delay of the off-axis maximum intensity is more obvious and the singularity is located nearer to the z-axis for the pulse with higher transverse modes. (C) 2007 Elsevier GmbH. All rights reserved.

Laser tunable Toraldo superresolution with a uniform nonlinear pupil filter

We demonstrate that it is possible to reduce the focal spot size by inserting a uniform nonlinear thin film at the aperture of a focusing lens. The reduction of spot size is tunable by adjusting the incoming laser power. In comparison with the original diffraction spot, the transverse spot size can be reduced 0.65 times. The nonlinear thin film acts effectively as a Toraldo filter, and the phase and amplitude modulation stems from the laser-induced variances in the transmission of the thin film. The proposed technique removes the need of fabricating annular pupil filters. (C) 2008 Optical Society of America.

基于正交频率变换的高功率蓝绿全固态激光器

对多横模全固态激光器使用正交频率变换进行了分析,计算了频率转换效率与激光发散角的关系。使用双KTP晶体正交倍频的方法,对Nd∶YAG激光器输出的含有高阶横模的激光进行倍频实验研究。在1064 nm Nd∶YAG激光基波功率密度为121 MW/cm2时,其谐波转换效率达到75.5%。研究表明,对于光束质量较差的基波激光,采用正交频率变换的方式,适当选择晶体参数,同样可以获得较高效率的二次谐波输出。

双包层光纤侧面耦合器

研究了一种侧面抽运双包层光纤的方法，从被剥除了外包层、端面为350μm×400μm的D型双包层光纤内包层上切下长度为3mm的一段柱体，并胶合在相同的双包层光纤内包层的侧面上，构成了柱体-光纤侧面耦合器。半导体激光器的抽运光从该柱体的一端入射并通过它耦合进入双包层光纤的内包层，实验测得耦合器最大耦合效率为85％。该方法适用于输出功率为数瓦的光纤激光器和放大器的侧面抽运。

大模场面积多模光纤激光器的横模控制

缠绕技术通常被用于大模场面积多模光纤激光器的横模控制。将光纤弯曲成不同半径的圆环，多模光纤激光器的高阶横模逐个被抑制并在缠绕半径为20mm时，获得15.4W的单模激光输出。实验研究表明，缠绕半径减小时，由于激光器高阶模式被抑制，其光束质量变好，同时其斜率效率降低。实验测量了多模光纤激光器在不同缠绕半径下的输出性能，并理论计算了各阶模式在不同缠绕半径下的损耗特性。实验测量结果与理论计算结果符合得较好。

大模场面积光纤激光器79．4W单横模输出

abstract {A large-mode-area (LMA) multimode fiber before and after coiling was studied contrastively in the experiment. Single-transverse-mode output was achieved when the fiber laser was coiled around a mandrel of 65 mm radius. After coiling, beam quality factor of the laser dropped from 1.24 to 1.06 and slope efficiency dropped from 64.7% to 54.3%. When the launched pump power was 149 W, the corresponding output power was 94.7 W and 79.4 W, respectively. However, the brightness of the coiled fiber laser was 1.15 times that of the uncoiled. Coiled modal losses of different modes were also calculated for the fiber employed in the experiment. The measured results agree well with the calculated ones.}

侧面泵浦的短矩形掺钕磷酸盐玻璃光纤激光器

利用光纤－波导耦合器技术侧面泵浦一根4厘米长的短光纤，我们研制得到了一个红外波长的光纤激光器。该激光器的增益介质是横截面为矩形的掺钕磷酸盐玻璃光纤，其纤芯横截面尺寸为1.5×0.5 毫米，数值孔径为0.2。单横模激光可以通过该矩形光纤的增益-导引效应来获得。最大的激光输出功率为1.05瓦，斜率效率为10％。

Welding of Al alloy plates using a novel high-average-power pulsed CO2 laser

A novel high-average-power pulsed CO2 laser with a unique electrode structure is presented. The operation of a 5-kW transverse-flow CO2 laser with the preionized pulse-train switched technique results in pulsation of the laser power, and the average laser power is about 5 kW. The characteristic of this technique is switching the preionized pulses into pulse trains so as to use the small preionized power (hundreds of watts) to control the large main-discharge power (tens of kilowatts). By this means, the cost and the complexity of the power supply are greatly reduced. The welding of LF2, LF21, LD2, and LY12 aluminum alloy plates has been successfully achieved using this laser. (c) 2005 Society of Photo-Optical Instrumentation Engineers.

Welding of Al alloy plates using a novel high-average-power pulsed CO2 laser

A novel high-average-power pulsed CO2 laser with a unique electrode structure is presented. The operation of a 5-kW transverse-flow CO2 laser with the preionized pulse-train switched technique results in pulsation of the laser power, and the average laser power is about 5 kW. The characteristic of this technique is switching the preionized pulses into pulse trains so as to use the small preionized power (hundreds of watts) to control the large main-discharge power (tens of kilowatts). By this means, the cost and the complexity of the power supply are greatly reduced. The welding of LF2, LF21, LD2, and LY12 aluminum alloy plates has been successfully achieved using this laser. (c) 2005 Society of Photo-Optical Instrumentation Engineers.