Core size scaling of helical-core optical fibres

The mode-area, scaling properties of helical-core optical fibres are numerically studied and the limit of core size for achievable single-mode operation is explored. By appropriate design, helical-core fibres can operate in a single mode with possible scaling up to 300 mu m in core diameter with numerical aperture 0.1.

基于光纤环形镜的全光脉冲整形器

提出了一种基于光纤环形镜的全光脉冲整形器。该全光脉冲整形器利用波分复用器将控制光脉冲引入光纤环形镜中，控制光脉冲由于交叉相位调制在信号光上产生了非线性附加相移。信号光在耦合器中发生干涉，经过整形的信号光脉冲从脉冲整形器的出射端出射，信号脉冲的波形由非线性附加相移的波形决定。实验中．利用对控制脉冲光谱整形和啁啾展宽的方法来对控制脉冲进行时间脉冲的整形，该全光脉冲整形器实现了对单纵模激光的脉冲整形，同时实现了飞秒脉冲和单纵模整形脉冲的精确同步。在理论上数值计算了该全光脉冲整形器的输出特性，理论计算结果和实验结

一种制作掺Yb相移光纤光栅激光器的实验方案

采用遮挡法引入相移制作了掺Yb相移光纤光栅(PS-FBG)。在制作光栅的过程中,将其作为激光器的谐振腔,通过监测激光器的输出功率来确定相移大小。当激光器的输出功率开始下降时,停止曝光,此时引入的相移为π/2。为了使光栅的特性尽快稳定下来需要对光栅进行退火,这将导致引入的相移小于π/2。为了弥补退火过程中引起的相移降低,需要对退火后的光栅进行二次曝光,以使光栅的相移恢复π/2。利用该方法制作了一只光纤光栅激光器。当抽运功率为100 mW时,获得了25 mW的输出功率,信噪比(SNR)为60 dB。在1 h内

Femtosecond laser pulse irradiation of Sb-rich AgInSbTe films: Scanning electron microscopy and atomic force microscopy investigations

The single-layer and multilayer Sb-rich AgInSbTe films were irradiated by a single femtosecond laser pulse with the duration of 120 fs. The morphological feature resulting from the laser irradiation have been investigated by scanning electron microscopy and atom force microscopy. For the single-layer film, the center of the irradiated spot is a dark depression and the border is a bright protrusion; however, for the multilayer film, the center morphology changes from a depression to a protrusion as the energy increases. The crystallization threshold fluence of the single-layer and the multilayer films is 46.36 mJ/cm(2), 63.74 mJ/cm(2), respectively.

7.3 W国产单频光纤放大器

报道了一种MOPA式国产单频光纤放大器。该放大器采用连续波单频激光器作为主振荡器，采用我国自行设计和制造的大模场面积掺Yb双包层光纤作为功率放大器，在波长1064 nm处实现了最高7.3 W的连续激光输出，斜率效率为39%，光－光转换效率为26%。此外，对光谱特性及放大的自发发射的抑制也进行了探讨。

大模场面积光纤激光器拉锥法模式选择

大模场面积(LMA)光纤激光器的光束质量通常比单模光纤激光器的光束质量差。采用光纤拉锥的方法进行模式选择,从而提高大模场直径光纤激光器的光束质量。拉锥区距光纤激光器的输出端约5 mm,纤芯最小为9 μm,约为未拉锥部分纤芯直径26 μm的1/3。实验研究表明,在拉锥后,光纤激光器的光束质量因子M2由3.50减小为1.81,相应的斜率效率由63.6%减小为51.1%。虽然拉锥后最大输出功率减少了约19.8%,但其亮度增大为拉锥前的3倍。

Self-formation of quasiperiodic void structure in CaF2 induced by femtosecond laser irradiation

We report the self-formation of quasiperiodic void structure with the length of several hundred micrometers inside the CaF2 crystal. The quasiperiodical voids along the propagation direction of the laser beam were formed spontaneously after the irradiation of a single femtosecond laser beam which was focused at a fixed point inside the crystal sample. The length of the void array varied with the focal depth beneath the sample surface. The possible mechanism of the self-formed void structure was discussed. (c) 2007 American Institute of Physics.

Gain characteristics of Er3+-doped phosphate glass fibres

An erbium-doped phosphate glass fibre has been drawn by the rod-in-tube technique in our laboratory. The gain for the Er3+-doped phosphate glass fibre with different pump powers and with different input signal wavelengths is investigated. The 2.2-cm-long fibre, pumped by a single-mode 980-nm fibre-pigtailed laser diode, can provide a net gain per unit length greater than 1.8dB/cm. The pump threshold is about 50 mW at the wavelength of 1534 nm, and below 70 mW at 1550 nm. The gain linewidth of the Er3+-doped phosphate glass fibre is greater than 34 nm and can cover the C band in optical communication networks.

beam-shaping microstructure optical fiber

Microstructure optical fiber with uniform intensity distribution of the fundamental mode is proposed. The design guide line and characteristics of this kind fiber are demonstrated. The relationship between refractive index profile and structure parameters is investigated. The mechanism of forming uniform fundamental mode in these fibers is analyzed.

Three-dimensional micro- and nano-fabrication in transparent materials by femtosecond laser

Femtosecond pulsed lasers have been widely used for materials microprocessing. Due to their ultrashort pulse width and ultrahigh light intensity, the process is generally characterized by the nonthermal diffusion process. We observed various induced microstructures such as refractive-index-changed structures, color center defects, microvoids and microcracks in transparent materials (e.g., glasses after the femtosecond laser irradiation), and discussed the possible applications of the microstructures in the fabrication of various micro optical devices [e.g., optical waveguides, microgratings, microlenses, fiber attenuators, and three-dimensional (3D) optical memory]. In this paper, we review our recent research developments on single femtosecond-laser-induced nanostructures. We introduce the space-selective valence state manipulation of active ions, precipitation and control of metal nanoparticles and light polarization-dependent permanent nanostructures, and discuss the mechanisms and possible applications of the observed phenomena.

Laser-induced damage threshold of the antireflection coatings on quartz and sapphire under different laser modes

The laser-induced damage threshold (LIDT) and damage morphology of antireflection (AR) coatings on quartz and sapphire are investigated. A very interesting phenomena is found in the measurement. In the case of a single pulse laser, the LIDT of the AIR coatings on quartz is higher than that of sapphire. On the contrary, for a free-pulse laser, the LIDT of AIR coatings on sapphire is higher than that of quartz. (C) 2004 Society of Photo-Optical Instrumentation Engineers.

Single UV excitation of Hoechst 33342 and propidium iodide for viability assessment of rhesus monkey spermatozoa using flow cytometry

Many fluorescent probes excited by visible light have been used to assess sperm quality by flow cytometry. Developing a viability evaluation method using UV excited stains would be useful for multiparameter analysis of sperm function. This investigation was conducted to determine the efficacy of Hoechst 33342 (H342) and propidium iodide (PI) dual staining for evaluating rhesus monkey sperm viability through use of flow cytometry and excited by a single UV laser. The results showed that the live cells stained only with H342 strongly correlated with expected sperm viability, and flow cytometric analyses were highly correlated with fluorescence microscopic observation. Using H342/PI/SYBR-14 triple staining method, it was found that the live/dead sperm distributions were completely concordant in both H342/PI and SYBR-14/PI assays. In addition, this dual staining was extended with fluorescein isothiocyanate-conjugated peanut agglutinin (FITC-PNA) to simultaneously analyze viability and acrosome integrity of sperm cryopreserved using two different extenders, TTE and TEST, and indicated that TTE offered better Preservation of plasma and acrosome integrity than TEST Therefore, the H342/PI dual staining provides an accurate technique for evaluating viability of rhesus monkey sperm and should be valuable for multiparameter flow cytometric analysis of sperm function.

Mode Analysis and Design of a Low-Loss Photonic Crystal 60 degrees Waveguide Bend

The guided modes of a two-dimensional photonic crystal straight waveguide and a waveguide bend are studied in order to find the high transmission mechanism for the waveguide bend. We find that high transmission occurs when the mode patterns and wave numbers match, while the single-mode condition in the waveguide bend is not necessarily required. According to the mechanism, a simply modified bend structure with broad high transmission band is proposed. The bandwidth is significantly increased from 19 to 116 nm with transmission above 90%, and covers the entire C band of optical communication.

GaSb based midinfrared equilateral-triangle-resonator semiconductor lasers

Theoretical calculations of the mode characteristics of an equilateral-triangle resonator (ETR) with a 10 mu m cavity side length show that the fundamental mode, with longitudinal mode index of 25, has a wavelength of 2.185 mu m and a longitudinal mode separation of 100 nm. This mode has a quality factor (similar to 2x10(5)) that is much larger than the first (similar to 5x10(4)) and second (similar to 3x10(4)) order modes, indicating that single fundamental mode lasing should be accessible over a broad wavelength tuning range. An electrically injected ETR based on this design is fabricated from an InGaAsSb/AlGaAsSb/GaSb, graded-index separate-confinement heterostructure, laser diode wafer with a 2.1 mu m emission wavelength. This device achieved single mode, continuous wave operation at 77 K with a threshold current of 0.5 mA and a single mode wavelength tuning range of 3.25 nm, which is accomplished by varying the injection current from 0.5 to 6.0 mA. (C) 2008 American Vacuum Society.

An investigation of the mode characteristics of SOI submicron rib waveguides using the film mode matching method

The mode characteristics of SOI (silicon-on-insulator) submicron rib waveguides are very different from those of micrometer-sized ones. Using the full-vector film mode matching method, we propose a simple criterion to determine whether a waveguide mode is guided or not. The single-mode condition for deep-etched waveguides is obtained using this criterion. We also obtain the inherent TM mode leakage and sharp cancelation effects due to TE-TM mode coupling in shallow-etched rib waveguides from numerical simulations, which agree well with the analytical results based on total internal reflection and interference theories.