Application of the Sanchez-Lacombe lattice fluid theory to the system pvme/ps and model calculations

Cloud point curves reported in the literature for five representatives of the system poly(vinyl methyl ether)/polystyrene were evaluated theoretically by means of the Sanchez-Lacombe lattice fluid theory. The measured phase separation behavior can be described within experimental error using only one adjustable parameter (quantifying the interaction between the unlike mers). The Flory-Huggins interaction parameters calculated from this theoretical description depend in good approximation linearly on composition (volume fractions) and on the inverse temperature. An evaluation of these data yields a maximum heat effect which is almost one order of magnitude less (ca. -0.25 J/cm(3)) than obtained via Hess's cycle (dissolution of the components and of the blend) from calorimetric measurements. Model calculations on the basis of the present theory demonstrate that the critical points shift to a different extent upon a certain relative change in the molar mass of the blend components. The sensitivity of the calculated phase diagrams against changes in the scaling parameter decreases in the following order: interaction energies between unlike mers, differences in the scaling temperatures, pressures and densities.

Phase behavior in mixtures of a homopolymer and a block copolymer .4. SALS and SAXS studies

Phase behavior of blends of poly(vinyl methyl ether) (PVME) with four styrene-butadienestyrene (SBS) triblock copolymers, being of various molecular weights, architecture, and compositions, was investigated by small-angle light scattering. Small-angle X-ray scattering investigation was accomplished for one blend. Low critical solution temperature (LCST) and a unique phase behavior, resembling upper critical solution temperature (UCST), were observed. It was found that the architecture of the copolymer greatly influenced the phase behavior of the blends. Random phase approximation theory was used to calculate the spinodal phase transition curves of the ABA/C and BAB/C systems; LCST and resembling UCST phase behavior were observed as the parameters of the system changed. Qualitatively, the experimental and the theoretical results are consistent with each other. (C) 1996 John Wiley & Sons, Inc.

PHASE-BEHAVIOR IN MIXTURES OF A HOMOPOLYMER AND A BLOCK-COPOLYMER .1. FTIR AND DSC STUDIES

Miscibility in blends of three styrene-butadiene-styrene and one styrene-isoprene-styrene triblock copolymers containing 28%, 30%, 48%, and 14% by weight of polystyrene, respectively, with poly(vinyl methyl ether) (PVME) were investigated by FTIR spectroscopy and differential scanning calorimetry (DSC). It was found from the optical clarity and the glass transition temperature behavior that the blends show miscibility for each kind of triblock copolymers below a certain concentration of PVME. The concentration range to show miscibility becomes wider as the polystyrene content and molecular weight of PS segment in the triblock copolymers increase. From the FTIR results, the relative peak intensity of the 1100 cm-1 region due to COCH3 band of PVME and peak position of 698 cm-1 region due to phenyl ring are sensitive to the miscibility of SBS(SIS)/PVME blends. The results show that the miscibility in SBS(SIS)/PVME blends is greatly affected by the composition of the copolymers and the polystyrene content in the triblock copolymers. Molecular weights of polystyrene segments have also affected the miscibility of the blends. (C) 1995 John Wiley & Sons, Inc.

PREFERENTIAL SORPTION OF MODIFIED PVA MEMBRANE IN PERVAPORATION

The swelling processes of an annealed poly (vinyl alcohol) membrane, a NaOH-crosslinked poly (vinyl alcohol) membrane, a poly (vinyl alcohol)-N,N'-methylene bisacrylamide irradiation-crosslinked membrane and a poly (vinyl alcohol)/poly(AMcoAANa) blend membrane were investigated. Water was preferentially sorbed by all four membranes. The selective sorption factor alpha(s) and the selective diffusion factor alpha(d) were defined, and were used to characterize the effects of sorption and diffusion on selectivity. The results have shown that preferential sorption has a marked effect on selectivity. The mean diffusion coefficients and pervaporation properties of the four membranes are also discussed.

FRACTAL BEHAVIOR OF SPINODAL DECOMPOSITION IN POLYMER BLENDS

Fractal behaviour of ramified domains in the late stage of spinodal phase separation in a binary polymer blend of poly(vinyl acetate) with poly(methyl methacrylate) was investigated by optical microscopic method. In the late stage of the spinodal decomposition, the fractal dimension D is about 1.64. It implies that some anomalous properties of irregular structure probably may be explained by fractal concepts.

Development of a LCST membrane forming system for cellulose acetate ultrafiltration hollow fiber

A novel lower critical solution temperature (LCST) membrane forming system containing cellulose acetate (CA)/poly (vinyl pyrrolidone) (PVP 3 60K)/N-methyl-2-pyrrolidone (NMP)/1,2-propanediol with a weight ratio of 24.0:5.0:62.6:8.4 had been developed. CA hollow fiber ultrafiltration (UF) membranes were fabricated using the dry-wet spinning technique. The fibers were post-treated with a 200 mg/L hypochlorite solution over a period of 6 It at pH 7. The experimental results showed that water flux of a membrane decreased while retention increased with increasing CA concentration in a dope. It was concluded that the membrane pore size decreased with increasing CA concentration. The membrane fouling tendency for BSA was 3 times higher than that for PVP 24K. (C) 2004 Elsevier B.V. All rights reserved.

Hybridization of poly(4-vinyl pyridine)-b-polystyrene-b-poly(4-vinyl pyridine) aggregates in dioxane/water solution

Self-assembly of binary blends of two triblock copolymers of poly(4-vinyl pyridine)-b-polystyrene-b-poly(4-vinyl pyridine), i.e., P4VP(43)-b-PS260-b-P4VP(43) (P1) and P4VP(43)-b-PS366-b-P4VP(43) (P2), in dioxane/water solution was studied. These two triblock copolymers individually tend to form vesicles (P2) and cylindrical micelles (P1) in dilute solution. It was found that copolymer components in the blend, sample preparation method, and annealing time had significant effect on hybridization aggregate morphology. By increasing P1 content in the copolymer blends, fraction of looped and stretched cylinders increased, while fraction of bilayers decreased. Nearly no bilayer was observed when P1 content was above 85 wt%.

Preparation and characterization of poly(piperazineamide) composite nanofiltration membrane by interfacial polymerization of 3,3 ',5,5 '-biphenyl tetraacyl chloride and piperazine

Most nanofiltration (NF) membranes are composite and have a polyamide thin film prepared by interfacial polymerization. Their performances mainly correlate the structure of the thin film and monomers used for its preparation. In this work, a novel thin-film composite (TFC) nanofiltration membrane was successfully prepared from 3,3',5,5'-biphenyl tetraacyl chloride (mm-BTEC) and piperazine (PIP) through interfacial polymerization. Attenuated reflectance infrared (ATR-IR) and X-ray photoelectronic spectroscopy (XPS) were used to characterize the chemical composition of the membrane surface. The membrane performance was optimized by studying preparation parameters including monomer concentration, reaction time, and pH of aqueous phase.

Synthesis and Characterization of Hyperbranched Poly(ether amide)s with Thermoresponsive Property and Unexpected Strong Blue Photoluminescence

A facile and efficient strategy for the syntheses of novel hyperbranched poly(ether amide)s (HPEA) from multihydroxyl primary amines and (meth)acryloyl chloride has been developed. The chemical structures of the HPEAs were confirmed by IR and NMR spectra. Analyses of SEC (size exclusion chromatography) and viscosity characterizations revealed the highly branched structures of the polymers obtained. The resultant hyperbranched polymers contain abundant hydroxyl groups. The thermoresponsive property was obtained from in situ surface modification of abundant OH end groups with N-isopropylacrylamide (NIPAAm). The study oil temperature-dependent characteristics has revealed that NIPAAm-g-HPEA exhibits an adjustable lower critical solution temperature (LCST) of about 34-42 degrees C depending on the grafting degree. More interestingly, the work provided an interesting phenomenon where the HPEA backbones exhibited strong blue photoluminescence.

Preparation of poly (styrene-co-4-vinyl pyridine) /silica nanoscale hybrids supported cyclopentadienyltitanium trichloride (CpTiCl3) catalyst and styrene polymerization

To obtain a novel support with practical value for metallocene catalyst (eta -C5H5)TiCl3 (CpTiCl3), poly (styrene-co-4-vinylpyridine) /SiO2 nanoscale hybrid material (SrP/SiO2) was firstly produced as support. After pretreatment by methylaluminoxane (MAO), the hybrid materials reacted with CpTiCl3. The results from SAXS, SEM and TEM indicated the morphology and structure of organic/inorganic hybrid materials, and the size of inorganic particle in hybrid was nanoscale. The results from IR and XPS showed that there were two possible cationic active species in the hybrid-supported catalyst, the polymerization results of styrene proved this possibility.

Phase transition and transition kinetics of a thermotropic poly(amide-imide) derived from 70% pyromellitic dianhydride, 30% terephthaloyl chloride, and 1,3-bis[4-(4 '-aminophenoxy)cumyl]benzene

The phase transition and transition kinetics of a liquid crystalline copoly(amide-imide) (PAI37), which was synthesized from 70 mol% pyromellitic dianhydride, 30 mol% terephthaloyl chloride, and 1,3-bis[4-(4'-aminophenoxy)cumyl]benzene, was characterized by differential scanning calorimetry, polarized light microscopy, X-ray diffraction, and rheology. PAI37 exhibits a glass transition temperature at 182 degreesC followed by multiple phase transitions. The crystalline phase starts to melt at similar to 220 degreesC and forms smectic C (S-C) phase. The Sc phase transforms into smectic A (S-A) phase when the temperature is above 237 degreesC. The S-C to S-A transition spans a broad temperature range in which the S-A phase vanishes and forms isotropic melt. The WARD fiber pattern of PAI37 pulled from the anisotropic melt revealed an anomalous chain orientation, which was characterized by its layer normal perpendicular to the fiber direction. The transition kinetics for the mesophase and crystalline phase formation was also studied.

Crystal structure and mechanism of (Z)-1-[2-(phenyl-bromide-chloride)vinyl]-1-cyclohexanol

The crystal structure and mechanism of the title molecule are described. This crystal is orthorhombic, belonging to space group PC21/B with a=1,002 1(2) nm, b=1.483 0(3) nm, c=2.173 6(4) nm, V=3.230 39(2) nm(3), Z=2, D-c=1.80 g/cm(3), R=0.069 3. The structure was solved by direct method. The tin atom of the title compound exists in two distorted-trigonal-bipyramidal geometry, defined by two carbon, one bromide, one chloride and one oxygen atoms leading to a five-membered chelate ring. In the structure, the five-membered ring containing the intermolecular O-->Sn has a half chair conformation.

THE COMPATIBILITY AND CRYSTALLIZATION OF THE MIXTURES OF POLY (TETRAHYDROFURAN-b-METHYL METHACRYLATE) DIBLOCK COPOLYMER WITH POLYVINYL CHLORIDE HOMOPOLYMER

The compatibility and crystallization behaviour of the mixtures of poly (tetrahydrofuran-methyl methacrylate) diblock copolymer (PTHF-b-PMMA) with polyvinyl chloride has been studied. We found that the compatibility of these blends, in which there is special interaction between the homopolymer and the PMMA block of the copolymer, is much better than that of the AB/A type blends; and that the crystallization rate and crystallinity of PTHF microdomain changed greatly due to the swollen by PVC homopolymer. In this paper, these changes in cryatallization are well explained according to the theories of block copolymer blends and the density gradient model presented by JIANG Ming.

MISCIBILITY OF POLY(N-VINYL-2-PYRROLIDONE) WITH POLY(ETHER SULFONE) AND 2 PHENOLPHTHALEIN-BASED POLYMERS

Blends of poly(N-vinyl-2-pyrrolidone) (PVP) with poly(ether sulphone) and two phenolphthalein-based polymers, viz. phenolphthalein poly(ether ether sulphone) and phenolphthalein poly(ether ether ketone) were prepared by casting from a common solvent and studied by differential scanning calorimetry. It was found that all the PVP blends are miscible and show a single, composition-dependent glass transition temperature (T(g)). The T(g)-composition dependence has been analysed by the use of the Gordon-Taylor equation. The values of the k parameter in the Gordon-Taylor equation obtained are all not high for the three pairs, in accordance with the fact that there is no strongly specific interaction between PVP and any of the other polymers.

ISOPOLYMOLYBDIC ACID-POLY(4-VINYL)PYRIDINE FILM MODIFIED ELECTRODE

Electrochemical polymerization of 4-vinylpyridine produced a uniform poly(4-vinyl)pyridine(PVP) film on the glassy carbon (GC) electrode surface. The isopolymolybdic acid-PVP film-modified electrode was prepared by soaking the PVP/GC electrode in the 0.05 M H2SO4 aqueous solution containing 0.005 M isopolymolybdic acid (H4Mo8O26). The latter (catalyst) is incorporated and held in the PVP film electrostatically. The electrochemical behavior and electrocatalytic properties of this H4Mo8O26-PVP/GC electrode was described. The results indicate that this modified electrode has good stability and electrocatalytic activity on the reduction of chlorate and bromate ions in aqueous solution. The catalytic process is regarded as an EC mechanism.