Morphological studies of polyamide 1010/polypropylene blends

Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to examine the morphology of blends of PA1010 and polypropylene (PP) compatibilized with polypropylene grafted with glycidyl methacrylate (PP-g-GMA). It is found that the morphologies are dependent on the content of glycidyl methacrylate in PP-g-GMA and the mixing time. The size of the dispersed PP particles decreases as the content of GMA in the PP-g-GMA increases for binary blends of PA1010 and PP-g-GMA. Similar results are obtained for changing the mixing time. Ternary blends of PA1010, PP, and PP-g-GMA indicate that morphologies depend on the content of glycidyl metyacrylate in the PP-g-GMA and the miscibility of PP and PP-g-GMA. By changing the content of GMA in PP-g-GMA, it was possible to introduce significant changes of morphology. A matrix removal TEM method is used to investigate the interfacial structure of PA1010/PP blends containing PP-g-GMA as a compatibilizer. This technique shows the reaction product between PA1010 and PP-g-GMA to be located at interface as a surrounding layer around domain particles. SEM observation on the interface shows that the adhesion between PA1010 and pure PP is very weak and their interface boundary is sharp. For the samples of PA1010 and PP-g-GMA, it was found that the interface was not so obvious, and the reaction between PA1010 and PP-g-GMA strengthens the interface significantly. (C) 1997 Elsevier Science Ltd.

Binary alloys of nylon 1010 and ethylene-propylene copolymer: Chemical, morphological, and mechanical analysis

The modification of ethylene-propylene copolymer (EPM) has been accomplished by melt grafting of maleic anhydride (MAH) molecules promoted by radical initiators. The resulting EPM-g-MAH and EPM have been used to obtain binary nylon 1010/EPM or nylon 1010/EPM-g-MAH blends by melt mixing. It was found that the EPM-g-MAH copolymer used as the second component has a profound effect upon the properties of the resulting blends. This behavior has been attributed to a series of chemical and physicochemical interactions taking place between the two components. The interactions are due to the presence of the anhydride functionality on the copolymer and do not occur when this functionality is absent. The interaction has been confirmed by Fourier-transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, and scanning electron microscopic.

Morphological, thermal, and mechanical properties of polypropylene/polycarbonate blend

This work deals with the effect of compatibilizer on the morphological, thermal, rheological, and mechanical properties of polypropylene/polycarbonate (PP/ PC) blends. The blends, containing between 0 to 30 vol % of polycarbonate and a compatibilizer, were prepared by means of a twin-screw extruder. The compatibilizer was produced by grafting glycidyl methacrylate (GMA) onto polypropylene in the molten state. Blend morphologies were controlled by adding PP-g-GMA as compatibilizer during melt processing, thus changing dispersion and interfacial adhesion of the polycarbonate phase. With PP-g-GMA, volume fractions increased from 2.5 to 20, and much finer dispersions of discrete polycarbonate phase with average domain sizes decreased from 35 to 3 mu m were obtained. The WAXD spectra showed that the crystal structure of neat PP was different from that in blends. The DSC results suggested that the degree of crystallization of PP in blends decreased as PC content and compatibilizer increased. The mechanical properties significantly changed after addition of PP-g-GMA. (C) 1997 John Wiley & Sons, Inc.

Morphological studies on a novel poly(aryl ether ketone)

The morphology of a novel poly(aryl ether ketone) [PEDEKmK] was investigated via polarizing optical microscopy (POM), TEM, DSC, SAXS and electron diffraction (ED). A distinct change in lamellar thickness, orientation, and spherulitic morphology was observed due to crystal melting and recrystallization. However, the crystal packing mode is found to be identical before and after the recrystallization process.

Larval metamorphosis and morphological characteristic analysis of triploid shrimp Fenneropenaeus chinensis (Osbeck, 1765)

Both MI and MII triploids were successfully produced by heat shock in Chinese shrimp Fenneropenaeus chinensis. The inducing conditions for MI and MII triploids were optimized. The highest inducing rate obtained for MI triploids reached more than 90%, and that for MII triploids reached nearly 100% at the nauplius stage as evaluated using flow cytometry. Comparisons of survival rates at larval stages between triploids and diploids or diploids experiencing treatment and diploids without treatment were performed. At larval stage from nauplii to postlarvae, heat shocks lowered survival at larval stages even if the ploidy was not changed. Ploidy did not affect shrimp larvae survival, and no significant difference was found in the survival of shrimp larvae between MI and MII triploids. Highly significant differences were observed in the morphology of triploids and diploids, and no apparent difference was found in the morphology of MI and MII triploids at the grow-out stages. Discriminating formulae for triploid and diploid shrimp at grow-out stage were developed and could be used to distinguish triploids from diploids based on morphological parameters. MI and MII triploids of shrimp have the potential to be used in aquaculture.

Estimates of genetic parameters for growth traits of the sea urchin, Strongylocentrotus intermedius

Heritabilities and genetic and phenotypic correlations were estimated for body weight, test diameter, and test height of the sea urchin from measurements on progeny resulting from 11 sires and 33 dams by artificial fertilization of 3 females by single males, and measurements at 8, 10, and 12 months after metamorphism. Point estimate for heritabilities based on the sire components of variance were moderate to high for body weight (0.21-0.49), test diameter (0.21-0.47), and test height (0.22-0.37). Genetic correlations were significant for body weight with test diameter (0.30similar to0.65) and test height (0.30similar to0.54) and test diameter with test height (0.31similar to0.65). Genetic correlation estimates, derived the nested design and half-sib correlation analysis used in this study, appear to provide reliable estimates. Significant phenotypic correlations were found for body weight with test diameter (0.82similar to0.86) and test height (0.49similar to0.83), and test diameter with test height (0.47similar to0.84). The phenotypic correlations for test height with body weight (0.491) and test diameter (0.467) at 12 months' of age were smaller than those earlier sampling periods.(C) 2004 Published by Elsevier B.V.

Quantitative traits correlative analysis and growth comparison among different populations of bay scallop, Argopecten irradians

The shell traits and weight traits are measured in cultured populations of bay scallop, Argopecten irradians. The results of regression analysis show that the regression relationships for all the traits are significant (P < 0.01). The correlative coefficients between body weight, as well as tissue weight with shell length, shell height and shell width are significant (P < 0.05). But the correlative coefficients between the anterior and posterior auricle length with body weight as well as tissue weight are not significant (P > 0.05). The multiple regression equation is obtained to estimate live body weight and tissue weight. The above traits except anterior and posterior auricle length are used for the growth and production comparison among three cultured populations, Duncan's new multiple range procedure analysis shows that all the traits in the Lingshuiqiao (LSQ) population are much more significant than those of the other two populations (P < 0.01), and there is no significant difference between the Qipanmo (QPM) and Dalijia (DLJ) populations in all traits (P > 0.05). The results indicate that the LSQ population has a higher growth rate and is expected to be more productive than the other two populations.

Dietary-morphological relationships of fishes in Liangzi Lake, China

Species in Liangzi Lake were clustered into four trophic groups: Hemiramphus kurumeus and Hemiculter bleekeri bleekeri fed predominantly on terrestrial insects; Carassius auratus auratus and Abbottina rivularis on non-animal food; Hypseleotris swinhonis, Ctenogobius giurinus, Pseudorasbora parva and Toxabramis swinhonis on cladocerans or copepods; Culterichthys erythropterus on decapod shrimps. Gut length, mouth width, mouth height, gill raker length and gill raker spacing, varied widely among species. With the exception of three species pairs (H. swinhonis, C. glurinus; C. erythropterus, H. kurumeus; T. swinhonis, H. bleekeri bleekeri), principal components analysis of morphological variables revealed over-dispersion of species. Canonical correspondence analysis of dietary and morphological data revealed five significant dietary-morphological correlations. The first three roots explained > 85% of the total variance. The first root reflected mainly the relationship of gut length to non-animal feud, with an increase in gut length associated with an increase in non-animal food. The second root was influenced strongly by the relationship of the gill raker spacing to consumption of copepods, with an increase in gill raker spacing associated positively with copepods in the diet. The third root was influenced by the relationship of mouth gape to consumption of fish and decapod shrimps, with an increase in mouth gape associated with more fish and decapod shrimps in the diet. These significant dietary-morphological relationships supported the eco-morphological hypotheses that fish morphology influence food use, and morphological variation is important in determining ecological segregation of co-existing fish species. (C) 2001 The Fisheries Society of the British Isles.

Morphological and phylogenetic analysis of a Gymnodinium-like species from the Chinese Coast

A Gymnodinium-like species was studied with light microscopy (LM) and scanning electron microscopy (SEM). Also, the internal transcribed spacers (containing 5.8S rDNA) and large ribosomal subunit DNA (D1-D2) sequences were obtained by PCR amplification, and then sequenced to explore the relationships within our isolate, Gymnodinium and other Gymnodinium-like species, including Karenia, Gyrodinium, Karlodinium and Symbiodinium. The LM observation showed that the species was characterized by moving in a levorotatory direction, visible hypocone, epicone and transverse groove, all of which are typical for Gymnodinium. In addition, two flagella could be found under SEM. The phylogenetic analysis revealed that the isolate grouped with Symbiodium, rather than other relevant dinoflagellates. All results showed our isolate belongs to Symbiodium. The strain was isolated from a red tide water sample, denoting that Symbiodium may be causative species for algal bloom.

Short-term morphological changes after sand-digging during a sand sculpture activity

The morphology of the beach backshore and foreshore at Huiquan Bay, Qingdao, China, is characterized by a single intertidal sandbar system with a spring tide range of 4.59 m. The beach was measured with a laser total station of Leica TPS402. Contours of the beach were generated using data collected in March and November 2005. The survey method provided 2 mm measuring accuracy and 4-10 m horizontal spacing. The net accretion volume of the foreshore was about 11, 215 m(3) from March to November. After sand sculpture activity, the axis of the sand trough migrated onshore from about 3.5 m to 17.5 m on the foreshore beach in November. At the same time, the axis of the sandbar crest migrated onshore no more than 42.25 m on the northwest foreshore; and it migrated offshore no more than 23.75 m on the southeast foreshore. On the northwest and southeast foreshore beach, two strips of erosion areas with a thickness of 0-0.2 m appeared on the sandbar crest. Accretion occurred at the bottom of the sand trough with a thickness of similar to 0.2-0.6 m. The sandbar height decreased after sand sculpture activity, and it was no more than 0.7 m in March and 0.6 m in November. Human activities, such as sand digging on the sandbar crest during sand sculpture activity, also can disturb the beach morphology of intertidal bar systems. This phenomenon also was validated by comparison of beach morphology, the results of a color artificial tracer experiment and a sediment transportation trend prediction.

Phylogenetic position and morphology of thecae and cysts of Scrippsiella (Dinophyceae) species in the East China Sea

Resting cysts of the marine phytoplanktonic dinoflagellate Scrippsiella spp. are encountered in coastal habitats and shallow seas all over the world. Identification of Scrippsiella species requires information on cyst morphology because the plate pattern of the flagellated cell is conserved. Cysts from sediments of the East China Sea were identified based on traits from both the cysts and the thecal patterns of germinated cells. Calcareous cysts belonged predominantly to S. trochoidea (F. Stein) A. R. Loebl., S. rotunda J. Lewis, and S. precaria Montresor et Zingone. The former two species also produced smooth and noncalcified cysts in the field. A new species, S. donghaienis H. Gu sp. nov, was obtained from six noncalcified cysts with organic spines. These cysts are spherical, full of pale white and greenish granules with a mesoepicystal archeopyle. The vegetative cells consist of a conical epitheca and a round hypotheca with a plate formula of po, x, 4', 3a, 7 '', 6c (5c + t), 6 s, 5''', 2'''' and are morphologically indistinguishable from S. trochoidea. Results of internal transcribed spacer (ITS) sequence comparisons revealed that S. donghaienis was distinct from the S. trochoidea complex and appeared nested within the Calciodinellum/Calcigonellum clade. Culture experiments showed that the presence of a red body in the cyst and the shape of the archeopyle were constant within cell lines from one generation to the next, while the morphological features of the cyst wall, such as calcification and spine shape, appeared to be phenotypically plastic.

Morphological and ultrastructural characterization of the coelomocytes in Apostichopus japonicus

The coelomocytes suspended in the coelomic fluid and occurring in the coelomic epithelial layer of the sea cucumber Apostichopus japonicus (Selenka) (Holothuroidea: Aspidochirota: Stichopodidae) function as mediators of the immune system, trephocytic cells and nutrient transport cells. Types of coelomocytes are characterized based on their morphological and ultrastructural features. Flow cytometry plus light and electron microscopic analyses were conducted in order to characterize the coelomocytes of A. japonicus. Six types of coelomocytes were identified: lymphocytes, morula cells, amoebocytes, crystal cells, fusiform cells and vibratile cells. Within these major categories, several distinctive cell types occurred that might represent developmental stages. The mean +/- SD coelomocyte concentration in the individuals (body length: 10 to 15 cm; weight: 100 to 150 g) was (3.79 +/- 0.65) X 10(6) cells ml(-1). The coelomic fluid contained mainly hyalinocytes (76.69%) and granulocytes (23.31 %).

Feeding, morphological changes and allometric growth during starvation in miiuy croaker larvae

We investigated the effects of the timing of first feeding (larvae in F0, F1, F2, F3 and S were first fed on day 3, 4, 5, 6 days after hatching (DAH) and unfed, respectively) on feeding, morphological changes, survival and growth in miiuy croaker larvae at 24A degrees C. The fed larvae initiated feeding on 3 DAH and reached point of no return (PNR) on 6 DAH. Larvae in F0 and F1 groups survived apparently better than F2 group at the end of the experiment on 36 DAH. High larval mortality occurred from 3 to 7 DAH in all feeding groups, accounting for 40% (F0, F1 and F2 groups) to 90% (F3 and S groups) of the total mortality. Larvae in F0 and F1 groups grew better than F2 group throughout the experiment. Eye diameter, body height, head height and mouth gape of the first feeding larvae were more sensitive to starvation than other morphometrics and could be used as indicators for evaluating their nutritional status. Results indicated that delayed first feeding over 1 day after yolk exhaustion could lead to poor larval survival and growth. To avoid starvation and obtain good growth in culturing, larvae feeding should be initiated within 1 day after yolk exhaustion at 24A degrees C.

Morphological and genetic study of Prorocentrum donghaiense Lu from the East China Sea, and comparison with some related Prorocentrum species

In this paper, the detailed morphology of Prorocentrum donghaiense Lu from both field samples and cultures was examined, and a taxonomic comparison was made between P donghaiense and some related Prorocentrum spp. using morphological and molecular data and other published information. There were distinct differences among these species in morphological characteristics that historically have been presented as conservative features. The discrepancies extended beyond that of individual variations within the same species due to environmental factors. Therefore, these morphological features may not be conservative but, rather, polymorphic depending on environmental conditions. Based on this analysis, we suggest that the high-biomass bloom-forming species in the East China Sea, previously reported as Prorocentrum dentatum Stein, is P donghaiense Lu. The species reported from the East China Sea and Japanese and Korean waters appear to be the same species. Molecular data also suggest that P. dentatum (CCMP1517) and P. donghaiense are genetically identical. Therefore, the geographic distribution of P. donghaiense may be much wider than expected. (C) 2004 Elsevier B.V. All rights reserved.

Feeding resumption, morphological changes and mortality during starvation in Japanese flounder larvae

Japanese flounder Paralichthys olivaceus larvae established first feeding 3 days after hatching (DAH) at c. 17degreesC. Non-fed fish reached irreversible starvation at age 5 DAH. Non-fed fish showed similar feeding rate and feeding intensity as the fed fish when they were provided with prey before 5 DAH, after which the starved larvae did not feed even when prey became available. None of the six morphological measurements examined (total length, body height, eye height, head height, gut height and myotome height) showed significant differences between the non-fed and fed larvae until 5 DAH. Normal development continued only in the fed group, and the non-fed larvae showed reverse growth or body collapse after 5 DAH. Owing to the shrinkage and collapse at the top of head due to starvation, head height could be a sensitive indicator of starvation in Japanese flounder larvae. In the fed treatments, high mortality occurred from first feeding (3 DAH) to irreversible starvation (5 DAH), accounting for about two-thirds to three-quarters of the overall mortality (46-52%) throughout the experiments. This mortality was not prey density or larval density dependent. Mortality during the same period in the non-fed larvae accounted for about a third of the overall mortality (100%). (C) 2002 The Fisheries Society of the British Isles. Published by Elsevier Science Ltd. All rights reserved.