典型人类活动对边坡变形及稳定性的影响研究

China is a mountainous country in which geological hazards occurred frequently, especially in the east of China. Except the geology, topography and extreme climate, the large scale human activities have become a major factor to landslides. Typical human activities which induced landslides are fill, cut and underground mining. On the topic of the deformation mechanism and slope stability, taking three different man-made slopes as examples, deformation mechanism and slope stability were studied by several methods, such as field work, numerical modeling and monitor. The details are as following: (1) The numerical modeling approach advantages over other conventional methods such as limit methods, so the numerical modeling is the major tool in this thesis. So far, there is no uniform failure criterion for numerical simulation. The failure criterion were summarized and analyzed firstly, subsequently the appropriate criterion was determinated. (2) Taking 220kV Yanjin transformation substation fill slope as example, the deformable characteristic, unstable mode and laboratory tests were studied systematically. The results show: the slope deformation was probably caused by a combination effect of unfavorable topographic, geological and hydro geological conditions, and external loading due to filling. It was concluded that the creep deformation of the slope was triggered by external loading applied at the back of the slope. In order to define the calculating parameters, a set of consolidated drained (CD) tests, consolidated undrained (CU) tests, repeated direct shear tests and UCS tests were carried out. The stability of the slope before and after reinforcement was assessed using 3D numerical modeling and shear strength reduction technique. The numerical modeling results showed: the factor of safety (FOS) of the slope was 1.10 in the natural state, and reduced to 1.03 after fill, which was close to the critical state and it caused creeping slip or deformation under rainfall. The failure surface in the slope is in active shear failure, whereas tensile failure occurs at the slope crest. After the site was reinforced with piles, the FOS was 1.27. Therefore, the slope is stable after reinforcement measures were taken. (3) The cut slope stability is a complex problem. Taking the left cut slope of Xiangjiaba as example in this thesis, the deformation and slope stability were studied systematically by numerical modeling and monitor methods. The numerical results show: the displacement is gradually increasing along with the cutting, and the largest displacement is 27.5mm which located at the bench between the elevation 340 and 380. Some failure state units distribute near the undermining part and there is no linked failure state occurred from crest to bottom during cutting. After cutting, some failure units appeared at the ground surface between elevation 340 and 360. The increasing tense stress made the disturbed rock failed. The slope is stable after cutting by the monitor method, such as surface monitor, multipoint displacement meter, inclinometer and anchor cable tensometer. (4) The interaction between underground mining and slope stability is a common situation in mountainous. The slope deformation mechanism induced by underground mining may contributed significantly to slope destabilization. The Mabukan slope in xiangjiaba was analyzed to illustrate this. Failure mechanism and the slope stability were presented by numerical modeling and residual deformation monitor. The results show: the roof deformed to the free face and the floor uplift lightly to the free face. The subsidence basin is formed, but the subsidence and the horizontal movement is small, and there is no failure zone occurred. When the underground mining is going on, the roof deformation, subsidence and the horizontal movements begin increasing. The rock deformation near the free face is larger than the ground surface, and the interaction between these coal seams appeared. There are some tensile failures and shear failures occurred on the roof and floor, and a majority of failure is tensile failure. The roof deformation, subsidence and the horizontal movements increased obviously along with the underground mining. The failure characteristic is shear failure which means the tensile stress transformed to the compressive stress. So the underground mining will induced tensile stress first which lead to structure crack, subsequently the compressive stress appeared which result in slippage. The crest was subjected to horizontal tension which made the rock crack along with the joint. The long term residual deformation monitor demonstrates that the slope is stable after the underground mining stopped.

准噶尔盆地南缘台13井区侏罗系油藏表征与建模

Junggar Basin has a large amount of recoverable reserves, However, due to the unfavorable factors, such as bad seismic data quality, complex structure with many faults and less wells, the exploration of oil and gas is still relatively limited, so advanced theoretical guidance and effective technical supports are desirable. Based on the theories of sedimentology, as well as comprehensive studies of outcrops, seismic data, drilling data and setting of this area, the paper establishes the isochronous correlation framework, and analyzes the sedimentary facies types and provenance direction, and obtains the profile and plain maps of the sedimentary facies combined with the logging constrained inversion. Then the paper analyzes the reservoir controlling factors, reservoir lithology attribute, 4-property relationship and sensibility based on the sedimentary facies research, and sets up a 3D geological model using facies controlled modeling. Finally, the paper optimizes some target areas with the conclusions of reservoir, structure and reservoir formation.Firstly, the paper establishs the isochronous correlation framework by the seismic data, drilling data and setting of this area. The sedimentary facies in Tai13 well block are braided river and meandering river according to the analysis of the lithology attribute, logging facies and sedimentary structure attribute of outcrop. The concept of “wetland” is put forward for the first time. The provenance direction of Badaowan and Qigu formation is obtained by the geology setting, sedimentary setting and paleocurrent direction. The paper obtains the profile and plain maps of the sedimentary facies from the sand value of the wells and the sand thickness maps from the logging constrained inversion. Then, this paper takes characteristics and control factors of the Jurassic reservoirs analysis on thin section observation, scanning transmission electron microscope observation and find out the petrology characteristics of reservoir, space types of reservoir and lithofacies division. In this area, primary pores dominate in the reservoir pores, which believed that sedimentation played the most important roles of the reservoir quality and diagenesis is the minor factor influencing secondary porosity. Using stochastic modeling technique，the paper builds quantitative 3-D reservoir Parameter. Finally, combined the study of structure and reservoir formation, the reservoir distribution regularity is concluded: (a) structures control the reservoir formation and accumulation. (b) Locating in the favorable sedimentary facies belt. And the area which meets these conditions mentioned above is a good destination for exploration.

安塞油田三叠系延长组长10油层组沉积相研究

Ordos basin is a large-scale craton overlapping basin, which locates in western North China platform and possesses abundant hydrocarbon resources. Ansai area in 2007 to extend the head of Chang10 of Yangchang Formation has made breakthrough progress in the region, long a high of Gao52 was Chang10 industrial oil flow, for oil exploration Ansai Oil Field opened a new chapter. in 2008, high of Gao52, Wang519, Gao34 producing wells area of building and found the existence of Chang10 great potential for the discovery of Chang10 Reservoir, Ansai Oil Field for a new direction, showing a good exploration development prospects.The study of occurrence and distribution features of hydrocarbon should be made by new theories and evolutions of sedimentology, sequence stratigraphy, reservoir sedimentology and petroleum geology form different angles on the base of regional geology background. Ansai Oil Field is in mid Shanbei Slope, which is a considerable producing zone of Ordos basin. Chang10 of Yangchang Formation is an important oil-bearing series, which sedimentary formation was formed in Indosinian orogeny, Late Triassic, sedimentary background is a momentary uplifting in Ordos basin, and exploration and exploitation of hydrocarbon in this area is very important. To further descripte disciplinarian of accumulation hydrocarbon, carefully study on sedimentary facies, reservoir type and disciplinarian of accumulation hydrocarbon of Chang10 of Yangchang Formation in study area is needed. By collecting date of field profile, outcrop, core and many other geological, through sedimentary and oil geological analysis, sedimentary facies types were identified, distributing of sedimentary facies and extension of sand body were analyzed too. Finally, the main controlling factors of hydrocarbon and the favorable areas were found out by deeply studying sedimentary system and disciplinarian of accumulation oil&gas in Chang10 of Yangchang Formation, Late Triassic in Ansai Oil Field. Chang10 of Yangchang Formation is main study formation, which is divided into three members (Chang101, Chang102 and Chang103), Chang101 is subdivided into three (Chang1011, Chang1012and Chang1013) reservoirs. By defining Layered borderline between every member and detailed describing rock and electro characteristic, member zonation become more reasonable and accurate also sedimentary facies and disciplinarian of accumulation oil&gas in study area are confirmed Through researching sedimentary facies, reservoir sand and hydrocarbon migration, accumulation, distribution, hydrocarbon accumulation models of Chang10 of Yangchang Formation in study area is pointed out, which is lithologic hydrocarbon reservoir and tectonic-lithologic hydrocarbon reservoir. Different play is formed by different processes and factors. Through analysis of reservoir property, trap type and accumulation model, several favorable exploration areas can be found out in Chang 10 reservoirs （Chang1011, Chang1012and Chang1013） of the Ansai Oil Field.

乍得西南部中新生代火山作用与盆地演化

Located in the Central and West African, Chad, which is not well geological explored, is characterized by Mesozoic- Cenozoic intra-continental rift basins. The boreholes exposed that, during Mesozoic-Cenozoic times, volcanic activities were intense in these basins, but study on volcanic rocks is very weak, especially on those embedded in rift basins, and so far systematic and detailed work has still no carried out. Based on the project of China National Oil and Gas Exploration and Development Corporation, “The analysis of reservoir condition and the evaluation of exploration targets of seven basins in block H in Chad”, and the cooperative project between Institute of Geology and Geophysics, CAS and CNPC International (Chad) Co. Ltd., “Chronology and geochemistry studies on Mesozoic-Cenozoic volcanic rocks from southwestern Chad Basins”, systematic geochronology, geochemistry and Sr-Nd-Pb isotopic geochemistry studies on volcanic rocks from southwestern Chad basins have been done in the thesis for the first time. Detailed geochronological study using whole-rock K-Ar and Ar-Ar methods shows the mainly eruption ages of these volcanic rocks are Late Cretaceous- Paleogene. Volcanic rocks in the well Nere-1 and Figuier-1 from Doba basin are products of the Late Cretaceous which majority of the K-Ar (Ar-Ar) ages fall in the interval 95-75 Ma, whereas volcanic rocks in the well Ronier-1 from Bongor Basin and the Well Acacia-1 from Lake Chad Basin formed in the Paleogene which the ages concentrated in 66-52Ma. Two main periods of volcanic activity can be recognized in the study area, namely, the Late Cretaceous period and the Paleogene period. Volcanic activities have a general trend of south to north migration, but this may be only a local expression, and farther future studies should be carried on. Petrology study exhibits these volcanic rocks from southwestern Chad basins are mainly tholeiitic basalt. Major- and trace elements as well as Sr-Nd-Pb isotopic geochemistry studies show that the late Cretaceous and the Paleogene basalts have a definitely genetic relationship, and magmas which the basalts in southwestern Chad basins derived from were produced by fractional crystallization of olivine and clinopyroxene and had not do suffered from crustal contamination. These basalts are prominently enriched light rare earth elements (LREE), large-ion lithophile elements (LILE) and high field strength elements (HFSE) and depleted compatible elements. They have positive Ba, Pb, Sr, Nb, Ta, Zr, Hf anomalies and negative Th, U, P,Y anomalies. It is possible that the basalts from southwestern Chad basins mainly formed by mixing of depleted mantle (DM) and enriched mantle (EMⅡ) sources. The late Cretaceous basalts have higher (87Sr/86Sr)i ratios than the Paleogene basalts’, whereas have lower (143Nd/144Nd)i ratios than the latter, showing a significant temporal evolution. The mantle sources of the Late Cretaceous basalts may have more enriched mantle(EMⅡ) compositions, whereas those of the Paleogene basalts are relatively more asthenospheric mantle (DM) components. The mantle components with temporal change observed in basalts from Chad basins were probably correlated with the asthenospheric mantle upwelling and lithospheric thinning in Central and Western Africa since Mesozoic. Mesozoic- Cenozoic Volcanism in Chad basins probably is a product of intra- plate extensional stress regime, corresponded to the tectonic setting of the whole West and Central African during Cretaceous. Volcanism is closely correlated with rifting. As time passed from early period to late, the basaltic magma of Chad basins, characterized with shallower genetic depth, higher density and smaller viscosity, probably indicates the gradual strengthening evolution of the rifting. In the initial rife stage, volcanic activities are absent in the study area. Volcanic activities are basiccally corresponded with the strong extensional period of Chad basins, and the eruption of basalts was slightly lagged behind the extensional period. In the post-rift stage (30-0Ma), these basins shifted to the thermal sag phase, volcanic activities in the study area significantly decreased and then terminated.

急倾斜金属矿体开采岩体移动规律与变形趋势预测研究

Rockmass movement due to mining steep metallic ore body is a considerable question in the surface movement and deformation issue caused by underground mining. Research on coal mining induced rockmass movement and its prediction problem have been performed for a long-term, and have achieved great progress at home and abroad. However, the rockmass movement caused by mining steep metal mine is distinctivly different from coal seam mining.. Existing surface movement laws and deformation prediction methods are not applicable to the rockmass movement caused by mining steep metal mine. So far the home and abroad research to this theory is presently at an early stage, and there isn’t mature theory or practical prediction method, which made a great impact on production. In this paper, the research object—Jinchuan nickel mine, which is typical steep metal mine, characterized by complex geological conditions, developed faults, cracked rockmass, high geostress, and prominent engineering stability problems. In addition, backfill mining method is used in the mine, the features of rockmass movement caused by this mining method are also different from other mining methods. In this paper, the laws of rock mass movement, deformation and destroy mechanism, and its prediction were analyzed based on the collection of data, detailed in-sit engineering geology survey, ground movement monitoring by GPS, theoretical analysis and numerical simulation. According to the GPS monitoring of ground surface movement, ground subsidence basin with apparent asymmetry is developing, the influence scope is larger in the upper faulted block than in the lower faulted block, and the center of ground movement is moving along the upper faulted block direction with increasing depth of mining. During the past half and seven years, the largest settlement has amounted to 1287.5mm, and corresponding horizontal displacement has amounted to 664.6mm. On the ground surface, two fissure belts show a fast-growing trend of closure. To sum up, mining steep metal mine with backfill method also exist the same serious problem of rockmass movement hazards. Fault, as a low intensity zone in rockmass, when it located within the region of mining influence, the change of potential energy mainly consumed in fault deformation associated with rockmass structure surface friction, which is the essence of displacement and stress barrier effects characterized by fault rupture zone. when steep fault located in the tensile deformation region incurred by underground excavation, no matter excavation in hangingwall or in footwall of the fault, there will be additional tensile stress on the vertical fault plane and decrease in the shear strength, and always showing characteristics of normal fault slip, which is the main reason of fault escarpment appeared on the ground surface. The No.14 shaft deformation and failure is triggered by fault activation, which showed with sidewall move, rupture, and break down features as the main form of a concentrated expression of fault effects. The size and orientation of principal stress in surrounding rock changed regularly with mining; therefore, roadway deformation and damage at different stages have different characteristics and distribution models. During the process of mining, low-intensity weak structures surface always showed the most obvious reaction, accompany with surface normal stress decrease and shear strength bring down, to some extent, occurred with relative slide and deformation. Meanwhile, the impact of mining is a relatively long process, making the structure surface effect of roadway deformation and damage more prominent than others under the influence of mining. Roadway surrounding rockmass deformation caused by the change of strain energy density field after excavation mainly belongs to elastic deformation, and the correspondented damage mainly belongs to brittle rupture, in this circumstance, surrounding rockmass will not appear large deformation. The large deformation of surrounding rockmass can only be the deformation associated with structure surface friction or the plastic deformation of itself, which mainly caused by the permanent self-weigh volume force，and long-term effect of mining led to the durability of this deformation Good pitting fill effect and supporting effect of backfill, as well as the friction of rockmass structure surface lead to obvious macro-rockmass movement with long-lag characteristics. In addition, the loss of original intensity and new structure surface arisen increased flexibility in rockmass and fill deformation in structure surface, which made the time required for rockmass potential energy translate into deformation work associated with plastic deformation and structure surface friction consumed much, and to a large extent, eliminated the time needed to do those plastic work during repeated mining, all of which are the fundamental reason of rockmass movement aftereffect more significant than before. Mining steep deposits in high tectonic stress area and in gravity stress area have different movement laws and deformation mechanism. The steep deposit, when the vertical size of the mining areas is smaller than the horizontal size of the orebody, no matter mining in gravity stress area or in high tectonic stress area, they have similar features of ground movement with mining horizontal orebody; contrarily, there will appear double settlement centers on the ground surface under the condition of mining in high tectonic stress area, while there will always be a single center under the other condition. Meanwhile the ground movement lever, scale of mining influence area and macro features of ground movement, deformation and fracture are also different from mining in gravity stress area, and the fundamental reason lies in the impact of orientation of the maximum principal stress on rock movement features in in-site rock stress field. When mining thick and steep deposit, the ground surface movement and deformation characteristic curves are significantly different from excavating the horizontal ore bed and thin steep deposit. According to the features of rockmass movement rate, the development process of mining-induced rockmass movement is divided into three stages: raising stage, steadily stage and gradually decay stage. Considering the actual exploitation situation, GPS monitoring results and macro-characteristics of surface movement, the current subsidence pattern of Jinchuan No.2 mine is in the early stage of development. Based on analysis of surface movement rate, surface subsidence rate increase rapidly when mining in double lever at the same time, and reach its peak until the exploitation model ended. When double lever mining translate into single, production decreased, surface subsidence rate suddenly start to reduce and maintain a relatively low value, and the largest subsidence center will slowly move along with the hangingwall ore body direction with increasing depth of mining, at the same time, the scope and extent of subsidence in footwall ore body will begin magnify, and a sub-settlement center will appear on ground surface, accompanied with the development and closure trend of ground fissure, the surrounding rockmass of shaft and roadway will be confronted to more frequent and severe deformation and failure, and which will have a negative impact on the overall stability of No.2 mine mining. On the premise of continuity of rockmass movement, gray system model can be used in ground rockmass movement prediction for good results. Under the condition of backfill mining step by step, the loose effect of compact status of the hard, broken rockmass led to lower energy release rate, although surrounding rockmass has high elastic energy, loose and damage occurred in the horizontal ore body, which made the mining process safety without any large geological hazards. During the period of mining the horizontal ore body to end, in view of its special “residual support role”, there will be no large scale rockmass movement hazards. Since ground surface movement mainly related to the intensity of mining speed and backfill effect, on the premise of constant mining speed, during the period of mining the horizontal ore body to end, the rate of ground surface rockmass movement and deformation won’t have sudden change.

南海北部大陆边缘盆地深部地热特征用地球动力学演化

This report is a conclusion of the major research outcome during my post-doctoral residence of research and work. Its content covers the researches of the deep thermal characteristic and dynamics evolution beneath the northern margin basin of South China Sea. In this report, the each other action and effect between lithosphere ad mantle convection were regarded by the combine of deep and shallow study, subdivision from whole to part, and pay equal attention to determine the nature and fixed quantity. The investigative method we used in this report is geothermal and gravity methods. By the help of geological model and geophysics modeling, we calculated lithosphere thermal structure, rheology structure and mantle convection. Firstly, the report introduces concisely the purpose and the previous achievement to this research. Then, it analyzed the characteristic of heat flow on South China Sea. The structure of deep temperature and thermal has been calculated in some models of heat generation and conduction. The rock rheology structure also was computed by the relationship between temperature and viscosity. All these calculations were finished under the guidelines of combine with geology and geophysics. Meanwhile, the fields both deep mantle convection and small scale upper mantle convection are computed. Beside, the density and temperature disorder resulted by mantle convection were also computed with the convection field. After these, the report bring the contribution of local field of mantle convection, thermal construct and effective viscosity beneath the northern margin basin of South China Sea. And, base on the tectonic background and evolution feature, this report discussion the evolution mechanism of south China Sea and its northern margin basin. The end of this report, the main conclusion of this research was summarized and brings out.

中国东部上第三系硬粘土的工程地质特性及边坡开挖工程环境效应研究

The engineering geological properties of Neogene hard clays and related engineering problems are frontiers in the fields of Engineering Geology, Soil Mechanics and Rock Mechanics. Recently, it has been recognized that Neogene hard clay is the intermediate type of material between the soil and the rock. Many aspects of them, such as sampling, testing, calculating and engineering process, are special, which could not be researched by means of theories and methods of traditional Soil Mechanics of Rock Mechanics. In order to get real knowledge and instruct the engineering practice, intersect studying of multiple disciplines, including Engineering Geology, Soil Mechanics and Rock Mechanics, etc., is necessary. Neogene hard clay is one of the important study objects of regional problem rocks & soils in our country, which extensively distributed in China, especially in Eastern China. Taking the related areas along the middle line of the Project of Transferring Water from the South to the North (e.g. Nanyang basin, Fangcheng-Baofeng area and Handan-Yongnian area), South-west of Shandong, Xu-Huai area and Beijing area, etc. as main study areas, the paper divided Neogene hard clays into reduction environment dominated origin and oxidation environment dominated origin, which distributed on areas western and eastern to Mount Taihangshan respectively. Intermediate types are also existed in some areas, which mainly distribute near the edges of depositional basins; they are usually of transitions between diluvial and lacustrine deposits. As to Neogene hard clays from Eastern China, the clay particle content is high, and montmorillonite or illite/montmorillonite turbostratic mineral is the dominating clay mineral. The content of effective montmorillonite is very high in each area, which is the basis for the undesirable engineering properties of Neogene hard clays. For hard clays from the same area, the content of effective montmorillonite in gray-greenish hard clay is much higher than that in purple-brownish or brown-yellowish hard clay, which is the reason why the gray-greenish hard clay usually has outstanding expansive property. On the other hand, purple-brownish or brown-yellowish hard clay has relatively less montmorillonite, so its property is better. All of these prove that the composition (clay mineral) of Neogene hard clay is the control factor for the engineering properties. Neogene hard clays have obvious properties such as fissured, overconsolidated and expansive, which are the main reasons that many engineering problems and geological harzards usually occur in Neogene hard clays. The paper systematically elaborates the engineering properties of Neogene hard clays from Eastern China, analyses the relationships between engineering properties and basic indexes. The author introduces the ANN method into the prediction of engineering property indexes of hard clays, which provides a new way for quantitatively assessment and prediction of engineering property indexes. During investigation in the field, the author found that there exists obvious seam-sheared zone between different hard clays in Miocene Xiacaowan formation in Xu-Huai area. Similar phenomenon also exists near the borderline between Neogene hard clays and underlying coal measures in the Southwest of Shandong province, which could be observed in the cores. The discovery of seam-sheard zone has important theoretical and practical significance for engineering stability analysis and revealing the origin of fissures in Neogene hard clays. The macrostructure, medium structure and microstructure together control the engineering properties of hard clays. The author analyses and summarizes the structural effects on hard clays in detail. The complex of the strength property of hard clays is mostly related to the characteristics of fissures, which is one of the main factors that affect the choice of shear strength parameters. So structure-control theory must be inseparably combined with composition-control theory during the engineering geological and rock/soil mechanics research of hard clays. The engineering properties, such as fissured, overconsolidated and expansive, control the instability of engineering behaviors of Neogene hard clays under the condition of excavation, i.e. very sensitive to the change of existence environment. Based on test data analysis, the author elaborates the effects of engineering environment change on the engineering properties. Taking Nanyang basin as example, the author utilizes FEM to study the effects of various factors on stability of cutting canal slopes, than sets forth the characteristics, development laws and formation mechanism of the deformation and failure of hard clay canal slopes, summarizes the protection and reinforcement principles, as well as the protection and remedy steps. On the basis of comparison of engineering properties of domestic and foreign Neogene muddy deposits, in the view of whole globe and associated with the geological characteristics of China, the paper demonstrates that the intermediate type of the material between the soil and the rock, named "hard clay/soft rock", which can not be separated abruptly, really exists in China. The author has given a preliminary classification based on its geological origin and distribution law, which is very significant for promoting the mixture of Engineering Geology, Soil Mechanics and Rock Mechanics. In the course of large scales engineering construction in China, many engineering experiences and testing data are gained, summarizing these testing results and automatically managing them with computer technology are very necessary. The author develops a software named "Hard Clay-Soft Rock Engineering Geological Information Management and Analysis System (HRGIMS)", realizes the automatic and visual management of geo-engineering information, on the basis of information management, the functions of test data analysis and engineering property prediction are strengthened. This system has well merits for practice and popularization.

孤东油田馆陶组河流相储层流动单元模型与剩余油分布规律研究

Since C.L. Hearn presented the concept of flow unit in 1984, its generation mechanisms and controlling factors have been studied in many aspects using different methods by researchers. There are some basic methods to do the research, and there are several concepts and classification standards about flow unit. Based on previous achievements and using methodologies from sedimentary geology, geophysics, seismic stratigraphy, and reservoir engineering, the author systemically studies the factors controlling flow unit, puts forward a series of methods for recognition, classification and evaluation of flow unit. The results obtained in this paper have important significance not only for understanding the flow unit, but also for revealing the distribution of remaining oil. As a case, this paper deals with the reservoir rocks in Guantao Group of Gudong Oilfield. Zhanhua Sag, Jiyang Depression in Bohaiwan Basin. Based on the study of stratigraphic, depositional and structural characteristics, the author establishes reservoir geological models, reveals the geological characteristics of oil-bearing reservoir of fluvial facies, points out the factors controlling flow unit and geological parameters for classification of flow unit. and summarizes methods and technologies for flow unit study when geological, well-logging and mathematical methods are used. It is the first attempt in literatures to evaluate reservoir by well-logging data constrained by geological conditions, then a well-logging evaluation model can be built. This kind of model is more precise than ever for calculating physical parameters in flow unit. In a well bore, there are six methods to recognize a flow unit. Among them, the activity function and intra-layer difference methods are the most effective. Along a section, the composition type of flow unit can be located according amplitude and impedance on seismic section. Slice method and other methods are used to distinguish flow unit. In order to reveal the distribution laws of flow unit in space, the author create a new method, named combination and composition of flow unit. Based on microscopic pore structure research, the classification methods of flow unit are developed. There are three types of flow unit in the reservoir of fluvial facies. They have their own lithology, petrophysics and pore structure character. Using judgement method, standard functions are built to determine the class of flow unit of fluvial facies. Combining reservoir engineering methods, the distribution laws of remaining oil in different types, or in different part of a flow unit are studied. It is evident that the remaining oil is controlled by the type of flow unit. The author reveals the relationship between flow unit and remaining oil distribution, builds the flowing models, predicts the variation of reservoir parameters in space, put forward different methods developing remaining oil in different flow unit. Especially, based on the results obtained in this paper, some suggestions for the adjustment of the developing flow units have been applied in Districts No.4 and No.7, and good results have been yielded. So, the results of this paper can guide oil field development. They are useful and significant for developing the remaining oil and enhancing the oil recovery efficiency.

松辽盆地南部岩性油藏成藏模式与分布规律

According to the basic geologic conditions, the paper is directed by the modem oil-gas accumulation theory and petroleum system in which typical oil pools are analyzed and the shape of lithologic trap and geologic factors are pointed out. The process during which oil and gas migrate from source rock to lithologic trap is rebuilt, and the accumulation model of oil pool is set up. With the comprehensive application of seismic geologic and log data and paying attention to the method and technology which is used to distinguish lithologic accumulation. Promising structural-lithofacies zones are got and the distribution rule of various lithologic accumulation is concluded. With making use of the biologic mark compound, different reservoirs are compared. As a result, the oil and gas in HeiDimiao come from Nenjiang Group's source rocks; in SaErTu from QingShenkou Group's and Nenjiang Group's, and in PuTaohua. GaoTaizi and FuYang from QingShankou Group's. According to the development and distribution of effective source rock, oil distribution and the comparison in the south of SongLiao basin, the characteristic of basin structure and reservoir distribution is considered, and then the middle-upper reservoir of SongLiao basin south are divided into two petroleum system and a complex petroleum system. Because of the characteristic of migration and accumulation, two petroleum systems can furtherly be divided into 6-7 sub-petroleum systems,20 sub-petroleum systems in all. As a result of the difference of the migration characteristic, accumulation conditions and the place in the petroleum system, the accumulation degree and accumulation model are different. So three accumulation mechanism and six basic accumulation model of lithologic trap are concluded. The distribution of lithologic pools is highly regular oil and gas around the generation sag distribute on favorable structural-lithofacies zones, the type of lithological pool vary regularly from the core of sandstone block to the upper zone. On the basic of regional structure and sedimentary evolution, main factors which control the form of trap are discovered, and it is the critical factor method which is used to discern the lithologic trap. After lots of exploration, 700km~2 potential trap is distinguished and 18391.86 * 10~4 tons geologic reserves is calculated. Oil-water distribution rule of pinch-out oil pool is put up on plane which is the reservoirs can be divided into four sections. This paper presented the law of distribution of oil and water in updip pinch-out reservoir, that is, hydrocarbon-bearing formation in plane can be divided into four zones: bottom edge water zone, underside oil and water zone, middle pure oil zone and above residual water zone. The site of the first well should be assigned to be middle or above pure oil zone, thus the exploration value of this type of reservoir can be recognized correctly. In accordance with the characteristics of seism and geology of low permeability thin sandstone and mudstone alternation layer, the paper applied a set of reservoir prediction technology, that is: (1)seism multi-parameter model identification; (2) using stratum's absorbing and depleting information to predict reservoir's abnormal hydrocarbon-bearing range. With the analysis of the residual resource potential and the research of two petroleum system and the accumulation model, promising objective zones are predicted scientifically. And main exploration aim is the DaRngZi bore in the west of ChangLin basin, and YingTai-SiFangZi middle-upper assembly in Honggang terrace.

三角洲储层孔隙结构模型与剩余油分布研究——以临南油田沙河街组储层为例

The study of pore structure in reservoir was paid attention to in the early reservoir research and now a systematic research methodology is set up. On the limits of tools and conditions, methodologies and technologies on formation condition and distribution laws of pore structure and the relationship between remaining oil distribution and pore structure are uncertain and some knownage about it is also uncertain. As the development of petroleum industry, the characterization of pore structure and the prediction of remaining oil are the hot spot and difficult point in the research of oil development. The author pays a close attention to this subject and has done much research on it. In a case study in Linnan oilfield Huimin sag Jiyang Depression Bohai Bay basin by using a new method, named varied scale comprehensive modeling of pore structure, the author builds pore structure models for delta reservoir, reveals the remaining oil distribution laws in delta facies, and predicts the distribution of remaining oil in Linnan oilfield. By the application of stratigraphy, sedimentology and structure geology. the author reveals the genetic types of sandbody and its distribution laws, builds the reservoir geological models for delta sandstone reservoir in Shahejie group in Linnan oilfield and points out the geological Factors that control the development of pores and throats. Combining petrology and the reservoir sensitive analysis, the author builds the rock matrix models. It is the first time to state that rocks in different sentimental micro facies have different sensitive .response to fluid pressed into the rocks. Normally. the reservoirs in the delta front have weaker sensitivity to fluid than the reservoirs in delta plain, In same subfacies, the microfacies that have fine grain, such as bank and crevasse splay, have stronger reservoir sensitivity than the microfacies that have coarse grains, such as under-water branched channel and debauch bar. By the application of advanced testing, such as imagine analysis, scan electronic microscope, and morphology method, the author classifies the pore structure and set up the distribution models of pore, throat and pore structure. By the application of advanced theory in well-logging geology, the author finds the relationship between microscope pore structure and macroscopic percolation characteristics, and then builds the well-logging interpretation formulae for calculating pore structure parameters. By using the geostatistics methods, the author reveals the spatial correlative characteristics of pore structure. By application of conditional stochastic simulation methods, the author builds the 3D models of pore structure in delta reservoir. It is the base of predicting remaining oil distribution. By a great deal of experiments and theoretical deduction, The author expounds the laws of percolation flow in different pore structures, and the laws by which the pore structure controls the micro distribution of remaining oil, and then, states the micro mechanism of remaining oil distribution. There are two types of remaining oil. They are by-pass flow caused by micro-fingering and truncation caused by non-piston movement. By new method, the author states the different pore structure has different replacement efficiency, reveals the formation condition and distribution laws of remaining oil. predicts the remaining oil distribution in Linnan oil field, and put forward some idea about how to adjust the oil production. The study yielded good results in the production in Linnan oilfield.

新第三纪红河盆地特征及红河断裂活动对其形成与发育的控制

Based on geodynamic analysis of sedimentary basins, combined sedimentology with structural geology and other methods, the author studied the Honghe basin located in Yunnan province of Southwestern China. Sandstone slice grain size analysis, combined with field geology and indoors study indicate that a set of inland alluvial fan diposits, fluvial deposites, delta deposits and some lacustrine sediments are in Honghe basin. Studying on shape of the Honghe basin, sedimentary and structural characteristic and distribution of different kinds of conglomerate and its structural significance, we hold the idea that the formation and evolution of Honghe basin are controlled by the activity of Red River faut. Correlation of lithostratic cross section in Honghe basin and studying on activity of Red River fault indicate that Honghe basin was formed in two stages. It is a complex basin constitutes of the first-stage trans-releasing basin and the second-stage trans-downfaulted basin. Due to the uplift of Qinghai-Xizang plateau and deformation of orogeny, the western Yunnan and adjacent area move to SE direction as a result of Tectonic Escape. Right lateral strike slip occurred along Red River fault, trans-releasing basin formed at the bend part of the fault due to stress relexation. As the block escaping, it moves away from the other block of the Red River fault, the upper block move down obliquely and trans-downfaulted basin formed. Combined the age of phytolite and regional structural events, we think the first-stage transreleasing basin was formed in late Miocene, on the other words, the dextral strike slip of Red River fault may began in late Miocene (10-7Ma). The second-stage trans-downfaulted basin may be formed in early stage of Pliocene (about 4.7Ma). Subsequently, the bilateral faults dipping to the inside of the plateau and thrusting outwards occurred in the marginal region of Qinghai-Xizang plateau during its uplifting as a fan-shaped mountain body, this results in the uplift of the strata to the east of Red River fault and supply large quantity of provenance for the Honghe basin. In last Pliocene (about 3Ma), strong uplift of Qinghai-Xizang plateau leads to massive clastic sediment entered Honghe basin and causes its closure. As a kind of trans-tentional basin, trans-releasing basin is different to pull-apart basin. The author compared the Mosha trans-releasing basin with Jinggu pull-apart basin in SW Yunan, China, and described their character correspondingly. Otherwise, the author combined the predecessors' studding with conclusion of own study, discussed the kinematics of Ailaoshan-Red River belt in Cenozoic, and the relationship between the formation of Honghe basin and uplifting of Qinghai-Xizang plateau.

大别山碰撞造山带逆冲推覆构造运动学和动力学研究

Since the discovery of coesite-bearing eclogites in Dabie and Sulu region over ten years ago, the Dabie collisional orogen has been the "hot-spot" across the world. While many great progresses have been made for the last decade in the researches on the Dabie and Sulu UHP metamorphic rocks in the following fields, such as, petrology, mineralogy, isotope chronology, and geochemistry, the study of the structural geology on the Dabie orogen is still in great need. Thrust and nappe tectonics commonly developed in any collisional orogenic belt during the syncollisional process of the orogen. It is the same as the Dabic collisional orogen is concerned. The paper put much stress on the thrust and nappe tectonics in the Dabic orogenic belt, which have been seldom systematically studied before. The geometric features including the division and the spatial distribution of various thrust and nappe tectonics in the Dabie orogen have been first studied, which is followed by the detailed studies on their kinematic characteristics in different scales varying from regional tectonics to microtectonics. In the thesis, new deformation ages have been obtained by the isotopic methods of ~(40)Ar-~(39)Ar, Sm-Nd and Rb-Sr minerals-whole rock isochrons on the mylonites formed in three ductile shear zones which bounded three different major nappes in the Dabie collisional orogenic belt. And the petrological, geochemical characteristics of some metamorphic rocks as well as the geotectonics of their protoliths, which have also deformed in the ductile shear zone, are analyzed and discussed. In the paper, twelve nappes in the Dabie orogen are first divided, which are bounded by various important NWW or NW-strike faults and three NNE-strike faults. They are Shangcheng Nappe, Huoshan Nappe, Yuexi Nappe, Yingshanjian-Hengzhong Nappe, Huangzhen Nappe, Xishui-Huangmei Nappe, Zhoudang Nappe, Suhe-Huwan Nappe, Xinxian Nappe, Hong'an Nappe, Mulan Nappe and Hhuangpi-Susong Nappe. In the Dabie orogen, three types of thrust and nappe tectonics belonging to two stages have been confirmed. They are: (1) early stage ductile thrust -nappe tectonics which movement direction was top-to-the-south; (2) late stage brittle to ductile-brittle thrust-nappe tectonics which are characterized by double-vergence movement, including top-to-the-north and top-to-the-south; (3) the third type also belongs to the late stage which also characterized by double-vergence movement, including top-to-the-east and top-to-the-west, and related to the strike-slip movement. The deformation ages of both Wuhe-Shuihou ductile shear zone and Taihu-Mamiao ductile shear zone have been dated by ~(40)Ar-~(39)Ar method. ~(40)Ar/~(39)Ar plateau ages of biotite and mica from the mylonites in these two shear zones are 219.57Ma and 229.12Ma. The plateau ages record the time of ductile deformation of the ductile shear zones, which made the concerned minerals of the mylonites exhume from amphibolite facies to the middle-upper crustal conditions by the early stage ductile thrust-nappe tectonics. The mineral isochons of Sm-Nd and Rb-Sr dating on the same mylonite sample of the metamafic rocks are 156.5Ma and 124.56Ma respectively. The two isochron ages suggest that the mylonitic rock strongly deformed in the amphilbolite facies at 156Ma and then exhumed to the upper crustal green schist condition at 124Ma with the activities of the Quiliping-Changlinggang ductile shear zone which bounded to the southen edge of Xinxian Nappe. Studies of the petrological and geochemical characteristics of some meta-mafic rocks and discussion on the geotectonics of their protoliths indicate that their protoliths were developped in an island arc or back-arc basin or active continental margin in which calc-alkline basalts formed. This means that arc-accretion orogeny had evolved in the margins of North china plate and/or Yangtze plate before these two plates directly collided with each other during the evolution process of Dabie orogen. Three-stage evolution of the thrust-nappe tectonics in Dabie collisional orogen has been induced based on the above-mentioned studies and previous work of others. And a possible 3-stage exhumation model (Thrust-Positive Flower Structure Model) has also been proposed.

塔里木盆地轮南地区三叠系油气地质模型及油气预测研究

As an important measure to understand oil and gas accumulation during petroleum exploration and development, Petroleum geological model is an integrated system of theories and methods, which includes sedimentology, reservoir geology, structural geology, petroleum geology and other geological theories, and is used to describe or predict the distribution of oil and gas. Progressive exploration and development for oil and gas is commonly used in terrestrial sedimentary basin in China for the oil and gas generation, accumulation and exploitation are very intricate. It is necessary to establish petroleum geological model, adaptive to different periods of progressive exploration and development practice. Meanwhile there is lack of an integrated system of theories and methods of petroleum geological model suitable for different exploration and development stages for oil and gas, because the current different models are intercrossed, which emphasize their different aspects. According to the characteristics of exploration and development for the Triassic oil and gas pool in Lunnan area, Tarim Basin, the Lunnan horst belt was selected as the major study object of this paper. On the basis of the study of petroleum geological model system, the petroleum geological models for different exploration and development stages are established, which could be applied to predict the distribution of oil and gas distribution. The main results are as follows. (1) The generation-accumulation and exploration-development of hydrocarbon are taken as an integrated system during the course of time, so petroleum exploration and development are closely combined. Under the guidance of some philosophical views that the whole world could be understood, the present writer realizes that any one kind of petroleum geological models can be used to predict and guide petroleum exploration and development practice. The writer do not recognize that any one kind of petroleum geological models can be viewed as sole model for guiding the petroleum exploration and development in the world. Based on the differences of extents and details of research work during various stage of exploration and development for oil and gas, the system of classification for petroleum geological models is established, which can be regarded as theoretical basis for progressive petroleum exploration and development. (2) A petroleum geological model was established based on detailed researches on the Triassic stratigraphy, structure, sedimentology and reservoir rocks in the Lunnan area, northern Tarim Basin. Some sub-belt of hydrocarbon accumulation in the Lunnan area are divided and the predominate controlling factors for oil and gas distribution in the Lunnan area are given out. (3) Geological models for Lunnan and Jiefangqudong oil fields were rebuilt by the combinations of seismology and geology, exploration and development, dynamic and static behavior, thus finding out the distribution of potential zones for oil and gas accumulations. Meanwhile Oil and gas accumulations were considered as the important unit in progressive exploration and development, and the classification was made for Lunnan Triassic pools. Petroleum geological model was created through 3D seismic fine interpretation and detailed description of characteristics of reservoir rocks and the distribution of oil and gas, especially for LN3 and LN26 well zones. The possible distribution of Triassic oil traps and their efficiency in the Lunnan area has been forecasted, and quantitative analysis for original oil(water) saturation in oil pools was performed. (4) The concept of oil cell is proposed by the writer for the first time. It represents the relatively oil-rich zones in oil pool, which were formed by the differences of fluid flows during the middle stage of reservoir development. The classification of oil cells is also given out in this paper. After the studies of physical and numerical modeling, the dominant controlling factors for the formation of various oil cells are analyzed. Oil cells are considered as the most important hydrocarbon potential zones after first recovery, which are main object of progressive development adjustment and improvement oil recovery. An example as main target of analysis was made for various oil cells of Triassic reservoir in the LN2 well area. (5) It is important and necessary that the classification of flow unit and the establishment of geological model of flow unit based on analysis of forecast for inter-well reservoir parameters connected with the statistical analysis of reservoir character of horizontal wells. With the help of self-adaptive interpolation and stochastic simulation, the geological model of flow units was built on the basis of division and correlation of flow units, with which the residual oil distribution in TIII reservoir in the LN2 well area after water flooding can be established.

温度、压力耦合背景下多相流体运移的数学模型研究

The Mathematical modeling of multiphase fluid flow is an important aspect of basin simulation, and also is a topic of geological frontier. Based on coupling relation of temperature, pressure and fluid flow, this dissertation discusses the modeling which conform to geological regularities of fluid migration. The modeling that is multi-field and multiphase includes heat transport equation, pressure evolvement equation, solution transport equation and fluid transport equation. The finite element method is effective numerical calculation methods. Author applies it to solve modeling and implements the finite element program, and the modeling is applied to Ying-Qiong Basin. The channels of fluid vertical migration are fault, fracture and other high penetrability area. In this thesis, parallel fracture model and columnar channel model have been discussed, and a characteristic time content and a characteristic space content been obtained to illustrate the influences of stratigraphic and hydrodynamic factors on the process. The elliptoid fracture model is established and its approximately solution in theory is gotten. Three kinds of modeling are applied to analyze the transient variation process of fluid pressure in the connected permeable formations. The elliptoid fracture model is the most similar geology model comparing with the other fracture models so the research on this fracture model can enhance the understanding to fluid pressure. In the non-hydrodynamic condition, because of the difference between water density and nature gas density, nature gas can migrate upon by float force. A one-dimension mathematical model of nature gas migration by float force is established and also applied to analyze the change in the saturation of gas. In the process of gas migration its saturation is non-continuous. Fluid flow is an important factor which influences the distribution of the temperature-field, the change of temperature can influence fluid property (including density, viscidity, and solubility),a nd the temperature field has coupling relations to the fluid pressure field. In this dissertation one-dimension and two-dimension thermal convection modeling is developed and also applied to analyze convective and conductive heat transfer. Author has established one-dimension and two-dimension mathematical modeling in which fluid is a mixture of water and nature gas based on the coupling relation between temperature and pressure, discussed mixture fluid convection heat transfer in different gas saturation, and analyzed overpressure form mechanism. Based on geothermal abnormity and pore pressure distribution in Dongfong 1-1, Yinggehai Basin, South China Sea, one-dimension mathematical modeling of coupling temperature and pressure is established. The modeling simulates the process that fluid migrates from deep to shallow and overpressure forms in shallow. When overpressure is so large that fractures appear and overpressure is released. As deep fluid flow to shallow, the high geothermal then forms in shallow. Based on the geological characteristics in Ya13-1, two-dimension mathematical modeling of coupling temperature and pressure is established. Fluid vertically flows in fault and then laterally migrates in reservoir. The modeling simulates the geothermal abnormity and pore pressure distribution in reservoir.

流体地球化学：成因、流动和流体-岩石相互作用及塔里木盆地实例研究

Geofluid in sedimentary basins is related to petroleum generation, migration, accumulation and preservation, and is a topic of geological frontier. By integrating the multi-discipline methods of petroleum geochemistry, sedimentology, hydrogeology, petroleum geology and experimental geochemistry, the thesis has carried out experiments of microcline dissolution in solutions with organic acids, crude oil, brines with high total dissolved solids (TDS), and has dealt with Al distribution between the crude oil and the brines after the experiments. Cases for study includes Central Tarim, Hetianhe Gas Field and Kucha forland basin with data containing fluid chemistry and isotopic compositions, thin sections of sandstones and carbonates, homogenization temperatures and salinities of fluid inclusions, isotopic compositions of bulk rock and autigenic minerals. The aims are to elucidate fluid origin and flow in the three areas, effect of hydrocarbon emplacement on diagenesis, and to show occurrence of microbe-mediated, and thermochemical sulfate reduction in the Tarim Basin. Microcline dissolution experiments show that after 100 hour, part of the dissolved Al distributes in the crude oil, and the Al concentrations in the crude oil rise when organic acids are added. The result can be used to explain that most oilfield waters in the Tarim Basin are characterized by less than 3mg/L Al. Crude oil added to the solutions can enhance microcline dissolution, which is also observed in the case - Silurian sandstones with early crude oil emplacement in the Central Tarim. Al and Si have higher concentrations in the experiments of oxalic acid than of acetic acid under the same pH conditions, suggesting that there exist Al-oxalate and Si-oxalate complexes. Presence of acetate can enhance the activity of Ca and Al, but Al concentrations have not been increased significantly due to formation of small Al-acetate complex during the experiments. Relationships between δD and δ~(18)O in conjunction with chemistry of oilfield waters show that the waters are evaporated connate waters, which subsequently mixed with meteoric water, and were influenced by water-rock interactions such as salt dissolution, dolomitization of calcite, albitization of feldspar. In the Hetianhe Gas Field where salt dissolution took place, δD and δ~(18)O values can be used to trace nicely meteoric water recharge area and flow direction, but TDS can not. Part of the waters have high TDS but very light δD and δ~(18)O. When combined with paleo-topography, or fluid potentials, meteoric water is suggested to flow eastward in the Hetianhe Gas Field, which is the same with the Central Tarim. Whist in the Kuche forland basin, meteoric water may have permeated Cambrian-Ordovician strata. Relationship between ~(87)Sr/~(86)Sr and 1/Sr can be used to indicate migration and mixing of brines from carbonate strata (low ~(87)Sr/~(86)Sr ratio but high Sr content), clastic strata (high ~(87)Sr/~(86)Sr ratio but low Sr content) and crystalline basement (high ~(87)Sr/~(86)Sr ratio and heavy δ~(18)O value). Using this approach, it can be found that ~(87)Sr-depleted brine from Ordovician carbonates have migrated up to and mixed with ~(87)Sr-enriched waters from Silurian and Carboniferous sandstones, and that Silurian brines have mixed with meteoric water. In the Kuche forland basin, brines from the Cambrian and Ordovician carbonates have higher ~(87)Sr/~(86)Sr ratios than those from the overlying sandstones, when combined with chemistry, δ~(15)N and ~3He/~4He ratios of the coexisting natural gases, suggesting that the brines were derived from the basement. There exists some debate on the effect of hydrocarbon emplacement on mineral diagenesis. Case-study from Silurian sandstones in the Central Tarim show that quartz has kept overgrowing secondarily when oil saturation was decreased by meteoric water flushing subsequently to hydrocarbon emplacement. Silicon precipitates on the water-wet quartz surface, leading to decreased Si concentration close to the surface. A Si grads can result in Si diffusion, which supplies Si for quartz overgrowth. Hydrocarbon oxidation-sulfate reduction is an important type of organic-inorganic interaction. Not only can it make secondary alteration of hydrocarbons, but generate H_2S and CO_2 gases which can improve reservoir property. Thermochemical sulfate reduction took place at the temperatures more than 125 ℃ to 140 ℃ in the Cambrian-Ordovician carbonates, the products - H_2S and CO_2 gases migrated up to the Silurian, and precipitated as pyrite and calcite, respectively. The pyrite has an average δ~(34)S value close to those of Ordovician seawater and anhydrite, and calcite has δ~(13)C value as low as -21.5‰. In the Hetianhe Gas Field, sulfate reduction bacteria carried by meteoric water flowing eastward may have preferentially depleted ~(12)C of light hydrocarbon gases, and results in heavier δ~(13)C values of the residual hydrocarbon gases and higher molar CO_2 in the natural gases in the west than in the east. Coexisting pyrite has δ~(34)S values as low as -24.9‰.