Preparation of functionalized montmorillonites and their application in supported zirconocene catalysts for ethylene polymerization

Ethylene polymerization was carried out with zirconocene catalysts supported on montmorillonite (or functionalized montmorillonite). The functionalized montmorillonite was from simple ion exchange of [CH3O2CCH2NH3](+) (MeGlyH(+)) ions with interlamellar cations of layered montmorillonites. The functionalized montmorillonlites [high-purity montmorillonite (MMT)-MeGlyH(+)] had larger interlayer spacing (12.69 Angstrom) than montmorillonites without treatment (9.65 Angstrom). The zirconocene catalyst system [Cp2ZrCl2/methylaluminoxane (MAO)/MMT-MeGlyH(+)] had much higher Zr loading and higher activities than those of' other zirconocene catalyst systems (Cp2ZrCl2/MMT, Cp2ZrCl2/MMT-MeGlyH(+), Cp2ZrCl2/MAO/MMT, [CP2ZrCl](+)[BF4]/MMT, [Cp2ZrCl][BF4](-)/MMT-MeGlyH(+), [CP2ZrCl](+)[BF4](-)/MAO/MMT-MeGlyH(+), and [Cp2ZrCl](+)[BF4](-)/MAO/MMT). The polyethylenes with good bulk density were obtained from the catalyst systems, particularly (CP2ZrCl2/MAO/MMT-MeGlyH(1)). MeGlyH(+) and MAO seemed to play important roles for preparation of the supported zirconocenes and polymerization of ethylene. The difference in Zr loading and catalytic activity among the supported zirconocene catalysts is discussed.

M-HMS的合成、表征及在苯酚羟化反应中的催化性能

以同晶取代方法合成了 M-HMS(M=Fe、Cu、Co、V,HMS:Hexagonal Mesoporous Silicates)中孔分子筛 .经 XRD、IR、ESP表征 ,证明过渡金属离子已进入 HMS骨架中 .在苯酚羟化反应中考察了 M-HMS的催化性能 .结果表明 ,M-HMS的催化性能明显高于相对应的 M/Si O2 负载型催化剂 .依据引入 HMS骨架的过渡金属离子是苯酚羟化反应的活性中心 ,以及 H+ 和 OH- 可能参与反应的结果提出了可能的反应机理

Infrared and MAS NMR spectroscopic studies of Al18B4O33

The IR spectrum and B-11 and Al-27 MAS NMR spectra of Al18B4O33 are presented and discussed in relation to the possible existence of boron atoms substituting for aluminum atoms. The IR spectrum shows that the strong vibrations of the BO3 groups are present in the 1 500 similar to1 200 cm(-1) region, and very weak bands of BO4 units art present in the region from 1 000 to 1 100 cm(-1). B-11 MAS NMR spectrum indicates that the strong signal for BOB units appears in the region from delta +5 to delta +20, and the very weak signal for BO4 units is at about delta -1, while Al-27 MAS NMR spectrum shows five peaks at about delta +62, +42.1, +14, -4.7 and -6.4, originating from AlO4, AlO4, AlO5, AlO6 and AlO6, respectively, These results reveal that there are minor BO4 units in Al18B4O33, indicating that a small amount of B atoms substitute for Al atoms in the 4-fold coordination.

Fabrication and electrochemical behavior of a sol-gel-derived carbon ceramic composite electrode entrapping 2 : 18-molybdodiphosphate

A new type of inorganic-organic hybrid material incorporating carbon powder and alpha -type 2:18-molybdodiphosphate (P2Mo18) in a methyltrimethoxysilane (MTMOS) based gel has been produced by a sol-gel process and used to fabricate a chemically modified electrode. The P2Mo18-doped carbon ceramic composite electrode was characterized using SEM and cyclic voltammetry. Square-wave voltammetry with an excellent sensitivity was exploited to conveniently investigate the dependence of current and half-wave potential (E-1/2) on pH. The chemically modified electrode has some advantages over the modified film electrodes constructed by the conventional methods, such as long-term stability, reproducibility, and especially repeatability of surface-renewal by simple polishing in the event of surface fouling or dopant leaching. In addition, the modified electrode shows a good catalytic activity for the electrochemical reduction of bromate in an acidic aqueous solution. (C) 2000 Elsevier Science B.V. All rights reserved.

Synthesis and luminescence properties of organic-inorganic hybrid thin films doped with Eu(III)

In this study, silica-based transparent organic-inorganic hybrid films were prepared by the sol-gel method. Tetraethoxysilane and 3-(trimethoxysilyl)propyl methacrylate were used as the inorganic and organic compounds, respectively. Lanthanide complexes [Eu(phen)(2)]Cl-3 were incorporated into the organically modified silicates (ORMOSIL) and the luminescence properties of the resultant hybrid films (ORMOSIL:[Eu(phen)(2)]Cl-3) were characterized. The relative quantum efficiency was observed higher and the lifetimes were longer in hybrid films than those in pure silica films. Furthermore, thermal stability of hybrid films incorporating various concentration of Eu(III) complex was studied. (C) 2001 Elsevier Science B.V. All rights reserved.

Luminescence and energy transfer between Ce3+ and Mn2+ in alkaline earth borates

The luminescence of Ce3+ and Ce3+, Mn2+ co-doped BaB8O13 and SrB4O7 prepared in air is studied. The results show that tetravalent cerium ion can he reduced to trivalent state in the hosts and gives rise to efficient luminescence. Energy transfer between Ce3+ and Mn2+ is possible. Mn2+ ions can be efficiently sensitized by Ce3+ and exhibit green and red emissions which implied that Mn2+ occupied the crystallographic sites of cations and boron sites of the anoins, respectively. The intensity ratio of red to Been emission in matrix increases with the increasing of manganese concentration.

Formation of epsilon-FeXN/BN magnetic nanocomposite and its thermodynamic and kinetic analyses

A nanocomposite of nanometer-sized magnetic granular epsilon-FeXN embedded in a nonmagnetic amorphous boron nitride matrix was prepared by ball milling mixture of alpha-Fe and hexagonal boron nitride in argon atmosphere. The grain size of the epsilon-FeXN alloy was about 10-20 nm. The nitrogen concentration in the epsilon-FeXN alloy increases with extending milling time. Both thermodynamic calculation and the present experiment show that iron and nitrogen atoms have higher alloying driving force than iron and boron atoms. Analyses of thermodynamics and kinetics about formation of the epsilon-FeXN alloy suggested that the formation of the epsilon-FeXN alloy is related to amorphization of the hexagonal boron nitride and refinement of the alpha-Fe. II was found from the present experiment that a critical grain size of the alpha-Fe reacting with nitrogen in the amorphous boron nitride is about 8 nm.

Cure processing modeling and cure cycle simulation of epoxy-terminated poly(phenylene ether ketone) .2. Chemorheological modeling

Chemorheology and corresponding models for an epoxy-terminated poly(phenylene ether ketone) (E-PEK) and 4,4'-diaminodiphenyl sulfone (DDS) system were investigated using a differential scanning calorimeter (DSC) and a cone-and-plate rheometer. For this system, the reported four-parameter chemorheological model and modified WLF chemorheological model can only be used in an isothermal or nonisothermal process, respectively. In order to predict the resin viscosity variation during a stepwise temperature cure cycle actually used, a new model based on the combination of the four-parameter model and the modified WLF model was developed. The combined model can predict the resin viscosity variation during a stepwise temperature cure cycle more accurately than the above two models. In order to simplify the establishment of this model, a new five-parameter chemorheological model was then developed. The parameters in this five-parameter model can be determined through very few rheology and DSC experiments. This model is practicable to describe the resin viscosity variation for isothermal, nonisothermal, or stepwise temperature cure cycles accurately. The five-parameter chemorheological model has also successfully been used in the E-PEK systems with two other curing agents, i.e., the diamine curing agent with the addition of a boron trifluride monoethylamine (BF3-MEA) accelerator and an anhydride curing agent (hexahydrophthalic acid anhydride). (C) 1997 John Wiley & Sons, Inc.

INVESTIGATION ON THE LUMINESCENCE PROPERTIES OF DY-3+ AND EU-3+ IN ALKALINE-EARTH BORATES

In this paper, the yellow-to-blue intensity ratio of Dy3+ (Y/B) and the red-to-orange intensity ratio of Eu3+ (R/O) were studied in relation to the compositions and structures of alkaline-earth borates. The dependence of the energy of the Eu3+ charge-transfer band (CTB) and of the emission intensity of Dy3+ on the alkaline-earth ions and the boron content of the hosts is discussed.

大洋有孔虫微量元素研究

The most novel aspect of this thesis is the combination analysis of the boron isotopes and trace elements. What’s more, it also provides a reliable analytical technique, which is suitable for both boron isotopes and trace elements. Al/Ca values can be used to monitor the clay removal during the sample preparation. It is found that when Al/Ca>100 mol/mol, the measured boron isotopic compositions are always several permil lower than those properly cleaned. B/Ca ratios can be used to calculate the exact boron loaded for each sample. Otherwise, too much loading will lead to too long time for the whole analytical sequence, and too less loading might incur serious blank problem. One other benefit besides those discussed above is that the combination analysis of boron isotopes and trace elements on the same sample allows reconstruction of the marine carbonate system and atmospheric pCO2 without assumption of the other parameter. In the marine carbonate system, with the seawater pH from the foraminiferal 11B, one has to make an assumption on the other variable to obtain the rest four variables. A series studies found that U/Ca and B/Ca are potential proxies for seawater [CO32-]and [HCO3-], respectively. Since they are measured on the same sample with boron isotopes, hence, there is no spatial or temporal ambiguity in the incorporation of the two controlling parameters. With 11B and U/Ca, the reconstructed atmospheric pCO2 variations match the atmospheric pCO2 record from the Vostok ice core within ±20 ppm. The incorporations of U and B into foraminiferal carbonates are controlled by the overall growth rate of individual foraminifers and other possible factors. The reliable application of these proxies still require further calibrations. In a similar fashion, the combination analysis of boron isotopes and Mg/Ca also has great advantages. Mg/Ca has been proved to be a reliable proxy for the surface seawater temperature. With the combination analysis, one can determine the phase between changes in atmospheric pCO2 and surface seawater temperature, thus explore the cause and mechanism of the changes in atmospheric pCO2. .

潜山油藏裂缝分布规律研究－－以辽河盆地大民屯凹陷潜山油藏为例

With the example of Damintun Depression, Liaohe Oilfield, different methods to study fracture distribution were propsosed, i.e. combined crop, core, log, with seismic attribute and paleo-stress field to predict fractural reservoir. The following conclusions are drawn: 1. Secondary fracture and dissolution pore are the main reservoir space of fractured reservoir in Damintun buried hills through observing more than 270 meters core in 27 wells. Among them, structural fracture is the main reservoir spcace in Archaean metamorphism whose main mineral are silicates, while dissolution pore and structural fracture are the main reservoir space in Protozoic carbonate which has been proved with high dissolution. Structural fracture is not only the main reservoir space but also the influent path. 2. Actual core observation and log identification proved that the formation of buried hills have the following zone: weathering crust, fracturaed zone and compact zone, among which the weathering crust and fractured zone are the main reservoir. 3. The mineralogical component of rock is the inner factor and the tectonization is the outer factor, which control the development of structural fracture. The content of brittle material in rock influences the development of structural fracture. Dissolution, chemical eluviations, weathering and fill-up affect the development of structural fracture. 4. Basement faults control the distribution of structural fracture in Damintun Depression. The trend of fracture is consistent with that of faults and there is often large-scale fractural zone around faults. 5. Based on log response, the fracture is identified with core observation, imaging well log and ANN, which can provide geological basis for optimized perforation. 6. The methods for predicting fracture with structure restoration, seismic inversion and paleo-stress simulation aiming at different types of buried-hills reservoir, and then the spatial distribution of the fracture and density is obtained, which can provide geological basis for well site adjustment.

利用MC-ICP-MS测定硼同位素及其在西藏地热和盐湖中的初步应用

Based on previous studies, boron can be separated from aqueous samples with Amberlite IRA-743 resin. Experiments on the elute temperature, elute volume and the dynamic resin exchange capacity have been performed in this study. Results show that the dynamic exchange capacity of the resin is 4.2mg B/g and at room temperature, boron fixed on the resin within this capacity level can be extracted quantitatively by using 5ml 2%HNO3. A new procedure has been developed for the measurement of boron isotope ratios in water samples using a Neptune MC-ICP-MS, after resolving the memory effect, which is a key problem, and investigating the impacts of mass bias and Si matrix effect. Using this method, it usually takes 20 min to perform one measurement on 0.1ppm boron solution with a precision of 0.23‰ (SD). If the relative deviation between a sample and the standard is large, the washout time needs to be doubled to achieve a higher precision. δ11B values of water samples from Yangbajing geothermal field vary from -10.53 to -9.13‰. Owing to the large difference B concentration and the small B isotope difference between deep geothermal water and surface water, B isotope ratios of the shallow geothermal fluids are dominated by the deep end member rather than the shallower one in the mixing process. As a consequence, δ11B-B relation is indicative basically of a dilution process. Vapor-liquid separation and calcite scaling also greatly influence B isotope fractionation. δ11B values of water samples from Dagejia geothermal field are from -15.98‰ to -11.67‰. Boron in Changma River near the field has two sources, freshwater lakes (Dajiamang Lake and Canke Lake) and geothermal waters. Finally, a preliminary discussion is included on boron geochemical characteristics of the salt lakes in Shuanghu area and other geothermal fields, to provide information for future studies on boron isotope geochemistry of geothermal systems and salt lakes in Tibet.

中国北方表沙无机碳储量及次生碳酸盐固碳潜力研究

This paper selected the Taklamakan Desert and the Badain Jaran Desert as the research areas, tested the carbonate content of surface-sand samples of dunes using Eijkelkamp carbonate goniophotometer, and analyzed the spatial-distribution characteristics of carbonate and estimated the carbonate-stock and secondary carbonate-stock in 1m depth of surface sand in the Taklamakan Desert and the Badain Jaran Desert. In addition, the paper test XRD, SEM, TDA, stable carbon isotope and radioactive strontium isotope of lacustrine deposits in the Taklamakan Desert and carbonates, such as kunkar, root canal, lacustrine deposits, sinter and calcrete, in the Badain Jaran Desert. Resting on the achievements by our predecessors, it analyzed the mineral-composition differences of the carbonates, calculated the contents of secondary carbonate and, furthermore, evaluated their potential of sequestration of CO2 in the atmosphere. The overall goal of this study was to increase our understanding of soil carbonate in the context of carbon sequestration in the arid region in China. That is, to advance our understanding about whether or not secondary carbonate in desert is a sink for atmospheric CO2. The following viewpoints were obtained: 1 Carbonate contents of surface-sand samples decend from the south to the north of the Taklamakan Desert. The minimum lies in the south and the maxmum in the mid. Carbonate content of surface-sand of megadunes in the Badain Jaran Desert has low value generally in the dune-crest and the base of slope, and large value in the mid. The average of Carbonate contents of all sorts of collected samples in the same area of the Taklamakan Desert has small diffetences. The average is about 9%. 2 Using carbonate contents as key parameters, calculate the carbon-stock of carbonates in 1m depth of surface sand in the Taklamakan Desert and the Badain Jaran Deser.They are 1.13Pg and 0.19 Pg respectively. There are 0.53Pg and 0.088Pg carbon-stock of secondary-carbonates in 1m depth of surface sand in the Taklamakan Desert and the Badain Jaran Desert. 3 Through testing data from XRD （X-ray diffraction）and TAD ( Thermal Analysis Data), the most significant conclusion derived from is that the main mineral ingredient is calcite in different carbonate substances in arid regions, From the SEM(Scanning electron microscopy ) images, can obtains the information about the micro environment of different carbonate forms in which they can grow. 4 Selected gas by termal cracking and traditional phosphoric acid method, their δ13C show that δ13C is a good parameter to indicate the micro environment in which different secondary carbonate forms. From the δ13C of the same type samples, if the redeposit degree is hard, theδ13C is light, the redeposit degree is weak, the δ13C is heave. and the δ13C of the different type samples, δ13C is mainly controlled by the micro environment in which secondary formed. if the procedure is characterized by redeposit and dissolve of marine facies carbonate, δ13C is heavy, it is characterized by CO2 which produced by plant respiration,δ13C is light. 5 From the δ13C of lacustrine deposit in the different grain size, there exsit certain differences in their micro environment and secondary degree among different grain size in the same grade. 6 The secondary carbonate content of lacustrine deposits in Taklimakan Desert is 47.26%. And those of root canal, sinter, calcrete, kunkar, lacustrine deposit and surface sand in Badain Jaran Desert are 91.74%, 78.46%, 76.26%, 87.87%, 85.37%and 46.49%, respectively. Of different grain size samples, the secondary carbonate contents of coarse fraction (20-63μm), sub-coarse fraction (5-20μm) and fine fraction (<5μm) are 80.10%, 47.2%and 50.07%, respectively. 7 There is no obvious relevance betweenδ13C of secondary carbonate and the content of secondary carbonate,theδ13C of secondary carbonate mainly reflects the parameters of secondary process, the content of secondary carbonate reflects difference of secondary degree.. 8 Silicates potentially supply 3.4 pencent calcium source during forming process of lacustrine deposits in Taklimakan Desert. If calcium source is mainly supplied by goundwater, it can be calculated that about 5.18 %, 6.13%, 5.68%, 5.64 % and 6.82% silicates supply calcium source respectively for root canal, kunkar, lacustrine deposit, calcrete and sinter, during the forming process of different kinds of carbonates in Badain Jaran Desert.

内陆湖沼相和近海沼泽相沉积环境煤中微量元素和矿物的对比研究—以辽宁北票、江西建新和桥头煤研究为例

Using knowledge of geology, geochemistry, coal petrology, mineralogy, by means of a variety of advanced measuring methods such as inductively coupled plasma mass spectrometry (ICP-MS), inductively coupled atomic emission spectrometry (ICP-AES), X-ray powder diffraction (XRD), scanning electron microscopy with energy-dispersive spectrometer(SEM-EDS), sequential chemical extract and density fractions, the characteristics of trace elements and minerals in Jurassic Beipiao coal mine under inland limnetic sedimentary environment and in late Permian Jianxin and Qiaotou coal mines under paralic swamp sedimentary environment were studied. Compared with the average concentration in the world bituminous coals, the Beipiao coal was characterized by relatively high contents of Sc, Ti, Cr, Co, Ni, Zn, Se, Sr, Zr, Y, Ba, REE and Th, and lower contents of V, Rb, Cd, Sn, Pb, Bi and U; while the Jianxin coal was relatively enriched in Li, Sc, Ga, Sr, Y, Nb, Sb, Th and U, with low concentration of Be, Co, Ni, Cu, Ge, Zr, Mo, Cd, Cs, Ba, Pb and Bi; and the Qiaotou coal was enriched in Li, Sc, Sr, Nb, Ta, Zr, REE, Hf, Th and U, with low concentration of Be, V, Co, Ni, Cu, Ge, Mo, Cd, Cs, Ba, Tl, Pb and Bi. The concentrations of Ca, Mg and K in Beipiao coal are higher than those in Jianxin coal and Qiaotou coal, while Fe, S and Ti in Beipiao coal are lower than those in Jianxin coal and Qiaotou coal. The proximate analysis of coal samples was carried out, which indicated that Beipiao coal was medium- to high- ash (5.92-60.68%) with low sulphur coal, and Jianxin coal and Qiaotou coal was medium to high ash (8.85-46.33%) with high sulphur. The reflectivity was measured, which explained that Beipiao coal belonged to high volatile bituminous coal, Jianxin coal was low volatile bituminous coal and Qiaotou coal was low volatile anthracite. Quantitative maceral analyses were studied. The characteristics of rare earth elements (REE) were investigated, which showed that the total contents of REE were higher than that of the world's average content. With the increase of coal's metamorphic grade, the total contents of REE decreased from 98.5 X 10"6 of Beipiao coal to 94.2 X 10"6 of Jianxin coal, and to 75.9 X 10"6 of Qiaotou coal, and 5Eu reduced which indicated that the element Eu depleted. The characteristics of REE was controlled by the metamorphic grade of coal. And REE were mainly absorbed in clay minerals in Beipiao coal samples, while in Jianxin and Qiaotou coal mines, REE were primarily related to clay mineral and pyrite. The variation of trace elements in vertical direction of coal seams was studied, and the results showed that different trace elements differed greatly. The correlation between trace elements and ash were determined. Four major trace elements (aluminium-silicates, sulphide, carbonate and phosphate) accounted for the occurrence and distribution of most elements studied were determined. Coal samples were separated by density fraction, which showed that Cr, Cu, Mo and Pb were closely related to inorganic matters mainly distributed in P >2.6 and dropped remarkably in the density fractions P <2.3 . The occurrences of Co, Cr, Ni, As, Se, Mo, U were studied directly and quantitatively using sequential chemical extract with six steps, which showed that Co. Ni, Mo and U were mainly in the form of mineral, and As, Se chiefly in the form of organic state, while Cr mostly in the form of organic state and mineral. Major mineral phases presented in the Beipiao coal were Kaolinite, illite, quartz, calcite, and small amount of siderite, barite. While major mineral phases in Jianxin and Qiaotou coal were pyrite, kaolinite, and small amount of marcasite, rutile, sphalerite. This is the first time that the chromite in the coal was discovered in China, which indicates that Cr occurrence appeared in the form of chromite. The ratio of Sr/Ba, Sr/Ca and V/Ni in Beipiao coal mine under inland limnetic is smaller than that of in Jianxin and Qiaotou coal mines under paralic swamp. The ratio of K/Na and Th/U of Beipiao coal mine is higher than that of Jianxin and Qiaotou coal mine, which proved that Beipiao coal was not affected by sea water and Jianxin and Qiaotou coal were affected by sea water. Trace elements such as Cr, Ni, Mo in minerals were analyzed by SEM-EDS. The factors controlling the enrichment of trace elements can be divided into syngenetic stage factors and epigenetic stage factors.

黄土高原风成沉积和风化作用对黄土一古土壤地球化学组成的控制

Geochemical analyses have been carried out on the samples taken from the last 250 ka wind-blown loess-paleosol sequences at Huanxian, Xifeng, Changwu, and Lantian in central Chinese Loess Plateau. The result shows: 1) that major changes in chemical composition of the loess-paleoso! sequences are due to leaching and reprecipitation of carbonates, and resulted from dust grain size changes rather than chemical weathering of silicates; 2) that Si/Ti, Si/AI, and Si/Fe ratios can be used as a proxy of dust deposition intensity, and Na/AI ratio can also be used as indicator of climatic changes in genera! rather than of the summer monsoon intensity. Our results show that chemical composition was controlled by dust deposition and weathering, and imply changes of climate and environment in the Loess Plateau during last 250,000 years.