用核磁共振方法表征6(8)氨基-3H苯[1,2]氧嗪-1,4-二酮

用一维1HNMR、13CNMR方法研究了6(8)氨基-3H苯[1,2]氧嗪-1,4二-酮的结构,并通过二维1H-1H同核相关谱(COSY)、13C-1H异核相关谱(HMQC)及13C-1H异核远程相关谱(HMBC)进一步确定了该类化合物的1H谱和13C谱中各谱峰的归属,为研究同类化合物表征提供了依据。

填充油的种类对Fe系1,2-聚丁二烯性能的影响

研究了芳烃油和环烷烃油对充油铁系1,2-聚丁二烯橡胶性能的影响。结果表明,基础胶充油后门尼粘度值下降,可塑性增加,混炼行为变佳;填充芳烃油比填充环烷烃油的橡胶在拉伸强度、撕裂强度、伸长率和生胶门尼值等方面均有所提高;充油后虽然硫化胶硬度降低,但是生热和耐磨性能提高。填充芳烃油可适当提高硫化胶的抗湿滑性,但滚动阻力也升高。环烷烃油可降低硫化胶的滚动阻力。充油可适当改善胶料的抗老化性能。

间同立构1,2-聚丁二烯的合成和形态结构研究

间同立构1,2-聚丁二烯自1955年问世以来 ,引起人们的广泛关注 ,但绝大多数研究工作集中在聚合物的合成方面[1～3] ,对其形态结构方面的研究却很少报道[4] ,原因是该聚合物分子侧链含有大量双链 ,在较高温度下 (>150℃ )很容易产生热交联 ,这给结构研究造成了很大困难 .间同立构1,2-聚丁二烯的性能取决于间规度 ,低间规度聚合物呈现弹性体特征 ,而高间规度聚合物则是一种半结晶性塑料 ,其结晶为平面锯齿链正交堆砌 ,Pacm空间群[4] .本文采用一种新的催化体系 ,使合成的1,2-聚丁二烯间规度可以调控.同时首次报道了结晶性间规1,2-聚丁二烯稀溶液浇铸薄膜形成具有单晶取向的板条状片层结构,并应用电子显微学和电子衍射技术确定其晶体结构.1.实验部分1.1样品及试剂　乙酰基丙酮铁 [(Fe(acac) 3)纯度为 99.9% ],使用时配成0.2mol/ L的甲苯溶液 ;三异丁基铝 [Al(i-Bu) 3]由 Aldrich公司提供 ;氢化亚磷酸二乙酯 (DEP)及丁二烯由锦州化学公司提供 ;丁二烯通过蒸馏进行纯化 ;己烷使用前在 Na/ K合金...

结晶性间同立构1,2-聚丁二烯的单晶结构

近十几年来,结晶性间同立构1,2-聚丁二烯引起人们的广泛关注,但绝大多数研究工作集中在聚合物的制备、物理性质和应用方面[1～3],对于其结晶行为和晶体结构则未见报道 .原因是间同立构1,2-聚丁二烯分子侧链含有大量的双键,在较高温度下很容易交联 ,特别是高间规度的聚合物 ,由于其熔融温度高 (>200℃ )则更易产生交联,这给结晶行为和结构研究带来很大困难.结晶性间同立构1,2-聚丁二烯的晶体结构为平面锯齿链正交堆砌,Pacm空间群[4].我们曾报道了结晶性间同立构1,2-聚丁二烯的合成和溶液浇铸膜的板条状结构[5],本文采用薄膜熔体结晶的方法第一次成功地获得了间同立构1,2-聚丁二烯的单晶,并通过电子显微学和电子衍射技术确定了其晶体结构.1 实验部分1.1间同立构1,2-聚丁二烯的制备采用乙酰基丙酮铁 [Fe(acac) ]3、三异丁基铝 [Al(i-Bu)3]和氢化亚磷酸二乙酯 (DEP)的新催化体系制备间同立构1,2-聚丁二烯,具体合成路线参见文献 [5].本文所选用聚合物的1,2单元含量为 89.3 % ,间规度为 ...

Preparation, characterization and quantized capacitance of 3-mercapto-1,2-propanediol monolayer protected gold nanoparticles

Monolayer protected gold nanoparticles (MPCs) are the focus of recent research for their stability and are deemed as the building blocks of bottom-up strategies. In this Letter, 3-mercapto-1,2-propanediol monolayer protected gold nanoparticles (MPD-MPCs) were synthesized and characterized by transmission electron microscopy, UV/Vis spectroscopy, X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. The value of quantized double-layer capacitance (1.13 aF) of MPD-MPCs in aqueous media was obtained by differential pulse voltammograms.

Systematic study of the transfer of amino acids across the water/1,2-dichloroethane interface facilitated by dibenzo-18-crown-6

Facilitated ion transfer reactions of 20 amino acids with di.benzo-18-crown-6 (DB18C6) at the water/1,2-dichloroethane (W/DCE) interfaces supported at the tips of micro- and nano-pipets were investigated systematically using cyclic voltammetry. It was found that there were only 10 amino acids, that is, Leu, Val, Ile, Phe, Trp, Met, Ala, Gly, Cys, Gln (in brief), whose protonated forms as cations can give well-defined facilitated ion transfer voltammograms within the potential window, and the reaction pathway was proven to be consistent with the transfer by interfacial complexation/dissociation (TIC/TID) mechanisms. The association constants of DB 18C6 with different amino acids in the DCE (beta(0)), and the kinetic parameters of reaction were evaluated based on the steady-state voltammetry of micro- or nano-pipets, respectively The experimental results demonstrated that the selectivity of complexation of protonated amino acid by DB18C6 compared with that of alkali metal cations was low, which can be attributed to the vicinal effect arising from steric hindrance introduced by their side group and the steric bulk effect by lipophilic stabilization.

Studies of effect of phase volume ratio on transfer of ionizable species across the water/1,2-dichloroethane interface by a three-electrode setup

The electrochemical behavior of pyridine distribution at the water/1,2-dichloroethane interface with variable phase volume ratios (r=V-0/V-W) was investigated by cyclic voltammetry. The system was composed of an aqueous droplet supported on a Ag/AgCl disk electrode covered with an organic solution or an organic droplet supported on a Ag/AgTPBCl disk electrode covered with an aqueous solution. In this way, a conventional three-electrode potentiostat can be used to study an ionizable compound transfer process at a liquid/liquid interface with a wide range of phase volume ratios (from 0.0004 to 1 and from 1 to 2500). Using this special cell we designed, only very small volumes of both phase were needed for r equal to unity, which is very useful for the investigation of the distribution of ionizable species at a biphasic system when the available amount of species is limited. The ionic partition diagrams were obtained for different phase volume ratios.

Electrochemical recognition of alkali metal ions at the micro-water 1,2-dichloroethane interface using a calix[4]arene derivative

In this paper, a calix[4]arene derivative, 5,11,17,23-butyl-25,26,27,28-tetra-(ethanoxycarbonyl)-methoxy-calix[4]arene (L), is investigated as a host to recognize alkali metal ions (Li+, Na+, K+, Rb+ and Cs+) at the interface between two immiscible electrolyte solutions (ITIES). Well-defined cyclic voltammograms are obtained at the micro- and nano-water \ 1,2-dichloroethane (W \ DCE) interfaces supported at micro- and nano-pipets.

Study of ionizable drugs transfer across the water/1,2-dichloroethane interface with phase volume ratio equal to unity using a three-electrode system

The electrochemical behavior of ionizable drugs (Amitriptyline, Diphenhydramine and Trihexyphenedyl) at the water/1,2-dichloroethane interface with the phase volume ratio (r = V-o/V-w) equal to 1 are investigated by cyclic voltammetry. The system is composed of an aqueous droplet supported at an Ag/AgCl disk electrode and it was covered with an organic solution. In this manner, a conventional three-electrode potentiostat can be used to study the ionizable drugs transfer process at a liquid/liquid interface. Physicochemical parameters such as the formal transfer potential, the Gibbs energy of transfer and the standard partition coefficients of the ionized forms of these drugs can be evaluated from cyclic voltammograms obtained. The obtained results have been summarized in ionic partition diagrams, which are a useful tool for predicting and interpreting the transfer mechanisms of ionizable drugs at the liquid/liquid interfaces and biological membranes.

Novel two-dimensional sodium molybdenum phosphates containing {M(enMe)(2)}(2+) bridging groups (M = Ni, Cu; enMe=1,2-diaminopropane)

Two novel organic-inorganic hybrid compounds, (H(2)enMe)(4)(H3O)[Ni(enMe)(2)].[Na3Mo12O52P8(OH)(10)].5H(2)O (1) and (H(2)enMe)(4)(H3O)[Cu(enMe)(2)].[Na3Mo12O52P8(OH)(10)].5H(2)O (2) (enMe = 1,2-diaminopropane), have been hydrothermally synthesized and characterized by elemental analyses, IR, EPR, XPS, UV-Vis spectra and TG analyses. Single crystal X-ray diffraction shows that 1 and 2 are isostructural compounds. Both the compounds exhibit an unusual two-dimensional (2-D) window-like network consisting of one-dimensional (1-D) chains of sodium molybdenum phosphate anions connected by transition metal coordination complexes cations. Compound 1 and 2 represent the first 2-D molybdenum phosphate skeleton pillared by transition metal complex fragments.

3{1-[2-(-3-羟基-1-甲基-2-亚丁烯氨基)-苯亚氨基]-乙基}4-甲硫基-2,4-戊二烯-2-醇的不对称Schiff碱镍(Ⅱ)配合物的合成、结构和性质

由 5-(2-乙酰基-1-甲硫基-3-羰基-亚丁基)-丙二酸亚异丙酯 (1)与邻苯二胺及乙酸镍()经一步反应合成了3{1-[2-( -3-羟基-1-甲基-2-亚丁烯氨基)-苯亚氨基 ]-乙基} 4-甲硫基-2,4-戊二烯-2-醇(3)的不对称四齿 Schiff碱镍()配合物(2),X射线衍射结果表明,配合物 2属单斜晶系,P21/C空间群.a=1.1476(2)nm,b=1.1782(2)nm,c=1.4810(3)nm;β=111.73(2)°,V=1.8602(7)nm3,Z=4,Rf=0.0535.电化学(循环伏安)测定结果表明,该配合物在测定条件下(阳极峰电位为1.1)发生了不可逆的氧化-还原反应.

Synthesis and structural characterization of organolanthanide complexes with 1,2-dicarba-closo-dodecaborane-1,2-dichalcogenolate ligands

Reactions of anhydrous LnCl(3) (Ln = Nd, Gd, Dy, Er, Yb) with 2 equiv of LiCp' in THF afford the lanthanocene complexes Of CP'(2)Ln(mu-Cl)(2)Li(THF)(2) (CP' = eta(5)-t-BuC5H4, Ln = Nd (1), Gd (2), Dy (3), Er (4), Yb (5); Cp'= 1,3-eta(5)-t-Bu2C5H3, Ln = Nd (6), Gd (7), Dy (8), Er (9), Yb (10)). The molecular structures of 7 and 8 were characterized by X-ray crystallographic analysis. In these complexes, two Cp' ring centroids and two it-bridging chloride atoms around the lanthanide atoms form a distorted tetrahedron. The insertion of elemental chalcogen E (E = S, Se) into Li-C bonds of dilithium o-carborane in THF solution afforded dimers of dilithium. dichalcogenolate carboranes, [(THF)(3)LiE2C2B10H10Li(THF)](2) (E = S (12a), Se (12b)), which were confirmed by a crystal structure analysis. Reactions Of Cp'(2)Ln(mu-Cl)(2)Li(THF)(2) (1-10) with 12a or 12b gave dinuclear complexes of the formula [Li(THF)(4)](2)[Cp'(2)LnE(2)C(2)B(10)H(10)](2) (Cp'= eta(5)-t-BuC5H4, E = S, Ln = Nd (13a), Gd (14a), Dy (15a), Er (16a), Yb (17a); E = Se, Ln = Nd (13b), Gd (14b), Dy (15b), Er (16b), Yb (17b); Cp'= 1,3-eta(5)-t-Bu2C5H3 E = S, Ln = Nd (18a), Gd (19a), Dy (20a), Er (21a), Yb (22a); E = Se, Ln = Nd (18b), Gd (19b), Dy (20b), Er (21b), Yb (22b)). According to the X-ray structure analyses, the dianions of 13a and 13b contain two o-carborane dichalcogenolate bridges, and each CP'2Ln fragment is attached to one terminal and two bridging chalcogen ligands. The central Ln(2)E(2) four-membered ring is not planar, and the direct metal-metal interaction is absent.

Alkali metal ions transfer across a water/1,2-dichloroethane interface facilitated by a novel monoaza-B15C5 derivative

In this paper, a novel monoaza-B15C5 derivative, N-(2-tosylamino)-isopentyl-monoaza-15-crown-5 (L), is used as an ionophore to facilitate alkali metal cations transfer across a water/1,2-dichloroethane (W/DCE) interface. Well-defined voltammetric behaviors are observed at the polarized W/DCE interfaces supported at micro- and nano-pipets except Cs+. The diffusion coefficient of this ionophore in the DCE phase is calculated to be equal to (3.3+/-0.2) x 10(-6) cm(2) s(-1). The experimental results indicate that a 1:1 (metal: ionophore) complex is formed at the interface with a TIC/TID mechanism. The selectivity of this ionophore towards alkali ions follows the sequence Na+ > Li+ > K+ > Rb+ > Cs+. The logarithm of the association constants (log beta(1)(0)) of the LiL+, NaL+, KL+ and RbL+ complexes in the DCE phase are calculated to be 10.6, 11.6, 9.0 and 7.1, respectively. The kinetic parameters are determined by steady-state voltammograms using nanopipets. The standard rate constants (k(0)) for Li+, Na+, K+ and Rb+ transfers facilitated by L are 0.54+/-0.05, 0.63+/-0.09, 0.51+/-0.04 and 0.46+/-0.06 cm s(-1), respectively. The pH values of aqueous solution have little effect on the electrochemical behaviors of these facilitated processes. The results predicate that this new type of ionophore might be useful to fabricate electrochemical sensor of sodium ion.

Synthesis and crystal structure of the dimeric, Ti-O-Ti bridged hydrid form polyoxoanion [alpha-1, 2-PW10Ti2O39](2)(10-)

The reaction of trivacant precursor Nag [A-PW9O34] . 19H(2)O with Ti(SO4)(2) affords the novel dimeric, di-Ti-IV-substituted tungstophosphate K4Na6[alpha-1,2-PW10Ti2O39](2) . 14H(2)O. The X-ray structural determination shows the dimeric, anhydride structure was formed by two Ti-O-Ti bonds linking two di-titanium-substituted Keggin anion [alpha-1,2-PW10Ti2O40]. It was also characterized by elemental analysis, TGA, FT-IR and U-V-vis spectroscopies.

Synthesis and structure of iron complex with 1,2-dithiolate-1,2-dicarba-closo-dodecaborane [Li(THF)(4)][Fe(S2C2B10H10)(2)(THF)]

The crystal of complex [Li(THF)(4)][Fe(S2C2B10H10)(2)(THF)] 3 belongs to monoclinic, space group P2(1) with a = 11.964(2), b = 16.527(3), c = 12.554(3) Angstrom,beta = 108.70(3)degrees, V= 2351.3(8) Angstrom(3), Z = 2, M-r = 835.95, D-c = 1.181 g/cm(3), mu (MoKalpha) = 5.30 cm(-1), f(000) = '874, R = 0.0622 and Rw 0.1538 for 1641 observed reflections with I > 2sigma(I). The ionic complex,of 3 contains the square pyramidal anion of [Fe(S2C2B10H10)(2)(THF)](-) and the tetrahedral cation of [Li(THF)(4)](+). The iron is 5-coordinated and located in the square pyramidal configuration. The iron atom and the four sulfur atoms are almost coplanar. The Lithium atom is coordinated with four oxygen atoms of four THF molecules and located in a tetrahedral configuration.