PHOTOLUMINESCENCE AND SURFACE PHOTOVOLTAIC SPECTRA OF STRAINED INP ON GAAS

A high energy shift of the band-band recombination has been observed in the photoluminescence (PL) spectra of the strained InP epilayer on GaAs by metalorganic chemical vapor deposit. The strain determined by PL peak is in good agreement with calculated thermal strain. The surface photovoltalic spectra gives the information about energy gap, lattice mismatching, and composition of heteroepilayers, diffusion length, surface, and interface recombination velocity of minority carriers of heteroepitaxy layers.

Growth of SiGe by D-UHV/CVD at Low Temperature

The temperature is a key factor for the quality of the SiGe alloy grown by D-UHV/CVD. In conventional conditions,the lowest temperature for SiGe growth is about 550℃. Generally, the pressure of the growth chamber is about 10~(-5) Pa when liquid nitrogen is introduced into the wall of the growth chamber with the flux of 6sccm of the disilane gas. We have succeeded in depositing SiGe films at much lower temperature using a novel method. It is about 10.2 Pa without liquid nitrogen, about 3 magnitudes higher than the traditional method,leading to much faster deposition rate. Without liquid nitrogen,the SiGe film and SiGe/Si superlattice are grown at 485℃. The DCXRD curves and TEM image show that the quality of the film is good. The experiments show that this method is efficient to deposit SiGe at low temperature.

High-mobility Ga-polarity GaN achieved by NH3-MBE

GaN epilayers were grown on (0001) sapphire substrates by NH3-MBE and RF-MBE (radio frequency plasma). The polarities of the epilayers were investigated by in-situ RHEED, chemical solution etching and AFM surface examination. By using a RF-MBE grown GaN layer as template to deposit GaN epilayer by NH3-MBE method, we found that not only Ga-polarity GaN films were repeatedly obtained, but also the electron mobility of these Ga-polarity films was significantly improved with a best value of 290 cm(2)/V.s at room temperature. Experimental results show it is an easy and stable way for growth of high quality Ga-polarity GaN films.

沉积物中导热体周围水合物分解范围研究

沉积物水合物在热源周围的分解范围是水合物热开采以及相关灾害分析的重要基础数据.该文针对平面内边界有恒温热源的水合物热分解范围问题进行了理论分析和四氢呋喃水合物沉积物模型实验,并将两者结果进行了对比.结果表明:沉积物水合物最大分解范围主要取决于热源与环境温度的温差;热源周围水合物热分解最大范围的理论值与实验值接近,误差小于5%

液化土层中桶形基础承载力弱化的数值模拟

对动冰载作用下饱和砂土层液化过程中桶形基础承载力的弱化规律进行了数值模拟。建立液化土层的简化计算模型,采用FLAC3D软件分析了等效动冰载作用下土层不同位置的液化度及其主要影响因素;进而将具一定液化度土层的抗力作用等效为沿桶壁的不同刚度的非线性弹簧作用,在给定的位移破坏标准下确定不同液化度土层中桶形基础的承载力,分析液化土层中桶形基础承载力的弱化特征。在文中荷载条件和计算模型下,当土层顶面液化度为0.60、底面液化度为0.06时,土层中桶形基础的承载力降低12%。

粉土地层中桶形基础水平动载响应的离心机实验研究

对动载作用下分层土中单桶基础动承载特性、四桶基础动承载特性进行了离心机实验模拟,并对动载后桶基静承载力进行了模拟。结果表明:桶顶与粘土面相同时,有上覆粘土层条件下的桶基动力响应较无上覆粘土层条件下的孔压增长小,但沉陷大;桶顶与粘土层下的砂土面相同时比与粘土面相同时的响应大。桶基在动载后的静承载力得到提高。由于液化区的滤波和对动载的衰减作用,发生沉降的范围有限,离桶壁约一倍桶高距离。超孔隙水压从桶基边沿水平向逐渐衰减,从土面开始往下逐渐衰减到零。桶基周围砂土完全液化的厚度随载荷幅值的增加而增加,最大值约为桶高的40%。

角蟾科（Megophryidae; Anura）蝌蚪的形态多样性和生态适应

角蟾科（Megophryidae）是以角蟾属（Megophrys Kuhl and Van Hasselt, 1822）为模式属而建立的，隶于无尾目（Anura），变凹型亚目（Anomocoela）。角蟾科包括2 亚科11 属142 种，分布于东洋界，从巴基斯坦、中国西部向东直到菲律宾和苏达群岛；中国有9 属75 种分布于华中和华南地区。角蟾科被认为是原始的两栖动物之一，其分类学、系统学、生态学、动物地理学的研究均深受中外科学家的瞩目。近年来，通过形态学、古生物学、细胞学、生态学、支序系统学的研究，角蟾科的分类与系统学研究取得了较大进展。与成体形态和分子系统学研究结果相比较，蝌蚪的研究存在更多的问题和挑战，尚需深入研究：（1）角蟾科蝌蚪的形态多样性分析；（2）角蟾科的系统发育关系与蝌蚪的演化，以及口漏斗的起源；（3）角蟾科蝌蚪表型分化与栖息环境和觅食行为的适应演化。针对上述问题，本文对角蟾科9 属30 种蝌蚪的形态特征，包括外部宏观形态和口器外部结构特征、口器内部显微结构、唇齿和角质颌的亚显微结构作了深入细致、多层次的比较研究；通过12s rRNA 和cytochrome b 基因构建最大简约树，采用贝叶斯系统发育进行分析，蝌蚪型的演化采用祖先性状的重建方法分析；得到如下结论：1）初步将角蟾科蝌蚪分为4 种类型；并且建立了2 种新的角蟾科蝌蚪类型。A 型：拟髭蟾型蝌蚪，该型蝌蚪包括拟髭蟾属、髭蟾属、齿蟾属和齿突蟾属的物种；B 型：新类型，掌突蟾型蝌蚪，该型蝌蚪在本文中包括掌突蟾属、小臂蟾属的物种；C 型：新类型，短腿蟾型蝌蚪，一种特化类型，该型蝌蚪在本文中仅包括短腿蟾属的物种；D 型：角蟾型蝌蚪，该型蝌蚪在本文中包括无耳蟾属、小口拟角蟾属和异角蟾属的物种。2）对角蟾科的分类进行了修订：（1）支持角蟾科两个亚科的分类系统；（2）角蟾亚科包括拟角蟾属、异角蟾属、无耳蟾属和短腿蟾属；该亚科形态差异小，系统学关系比较复杂，暂不作族级分类的再划分；（3）拟髭蟾亚科分为2 个族：拟髭蟾族，该族物种具有类型A 的蝌蚪，包括4 个属：拟髭蟾属、髭蟾属、齿蟾属、齿突蟾属；掌突蟾族，该族物种具有类型B 的蝌蚪，包括2 个属：掌突蟾属和小臂蟾属。3）结合分子系统进化关系探讨了4 种蝌蚪类型的演化。（1）角蟾科蝌蚪的最近共同祖先来自于一类具有拟髭蟾型蝌蚪性状的蝌蚪；（2）掌突蟾型蝌蚪和角蟾亚科的蝌蚪是由具有拟髭蟾型蝌蚪性状的祖先蝌蚪分别演化而来；（3）短腿蟾型蝌蚪是角蟾型蝌蚪的一种特化类型；（4）外群蝌蚪具有与拟髭蟾型蝌蚪相似的性状，进一步印证了类拟髭蟾型蝌蚪是角蟾科蝌蚪的最近共同祖先的假说；（5）具有口漏斗的蝌蚪类型是由不具口漏斗的蝌蚪类型演化而来，在角蟾科中口漏斗是一种衍生性状。4）分析了角蟾科四种蝌蚪类型与栖息环境的适应演化。（1）角蟾科蝌蚪的口部和体形的变化反映了该科蝌蚪由缓流向类似静水生境的回水凼的渐变式适应，角蟾科蝌蚪的形态显示了多方面的适应变化；（2）随着蝌蚪类型由A 向D的演化，当水速较大时，拟髭蟾型的蝌蚪营流水攀吸型生活方式；当水速递减时，掌突蟾型蝌蚪营流水附着型生活方式；当水速进一步递减时，具有较小口漏斗的短腿蟾型蝌蚪和具有大漏斗的角蟾型蝌蚪营流水浮泳型生活。角蟾科蝌蚪对于水流递减的适应演化说明蝌蚪的生态学适应是具有进化意义的；（3）蝌蚪口器内部结构的分化揭示了蝌蚪和食性的适应关系，蝌蚪以口部的唇齿与角质颌刮取或吞吸水中的物质，然后，通过口乳突有选择地过滤进入口腔中食物。拟髭蟾亚科蝌蚪的唇齿多而窄，唇齿间距宽，颌鞘粗而稀，反映了其植食性为主的特点；它们的舌前乳突一般为指状，在口腔入口处所占面积小，其机械过滤的作用很多被唇齿和角质颌分担了；而角蟾亚科的蝌蚪，其角质颌弱，其舌前乳突一般为匙状，几乎填满了口腔入口处，因此舌前乳突起了主要的机械过滤作用。The family Megophryidae is the largest and most diverse families inArchaeobatrachia, and most of its species occur in India, Pakistan, and eastward intoChina, Southeast Asia, Borneo and the Philippines to the Sunda Islands. Currently thefamily includes 142 species have been grouped into two subfamilies, Megophryinaeand Leptobrachiinae. The mountains of central and southern China are rich in speciesof Megophryidae, 75 species belong to 9 genera and two subfamilies.The family was supposed to be ideal materials of studies in many fields of biology,such as taxonomy, evolution, systematics, ecology, and biogeography. Recently, therehave a great development in taxonomy and systematics of megophryids throughstudied by morphology, paleontology, cytology, ecology, and cladistics. However,larvae of megophryids were generally unknown, although the tadpoles might be veryimportant for above studies.In this paper, we examined the evolutionary scenario of the tadpoles’ morphologyin the context of a phylogenetic framework. Our objectives are (1) to evaluate thedivergence of larval body shape and oral discs in the family Megophryidae, (2) toexplore the evolutionary trends of the larvae in megophryidae, and test if thefunnel-shaped oral disc is apomorphic, and (3) to explore the relationship of the larvalstructure, diet and microhabitat.We examined larval morphology of 30 megophryid species, the larval body shape,oral discs, the buccopharyngeal cavity, and jaw sheaths and denticles of the Chinesemegophryid frogs were re-examined. We constructed a phylogeny of the species on thebasis of published mitochondrial cytochrome b and 16S rRNA gene segments usingpartitioned Bayesian analyses. Furthermore, hypothetical changes of larval morphologywere inferred using parsimony principle on the phylogeny. The results showed that:1) Four tadpole types in Megophryidae. The larval morphological charactersseries in Chinese megophryids fall into four general categories according to the bodyshape and oral discs: (A) Leptobrachiini type, species from genera Leptobrachium,Oreolalax, Scutiger and, Vibrissaphora share this type of tadpoles. (B) Leptolalax type,species of genus Leptolalax have this type of tadpoles. (C) Brachytarsophrys type,species of the genus Brachytarsophrys have this type of tadpoles. (D) Megophryinitype, species of the genera Atympanophrys, Ophryophryne, and Xenophrys share this type of tadpoles. Of which B and C are two novel types.2）Taxonomic implications. The present study leads us to reconsider the generalclassification of tribes attributed to members of Megophryidae. More specifically,concerning the phylogenetic relationships and the two novel tadpole types describedherein, we propose a provisional taxonomy for the family but suggest that further taxasampling of other megophryids be performed to confirm this taxonomic change. TheMegophryidae is composed of two subfamilies (Leptobrachiinae and Megophryinae).The Leptobrachiinae was recogonized the two tribes: (1) tribe Leptobrachiini sensuDubois, corresponding to the tadpole of type A, including four genera, i.e.,Leptobrachium, Oreolalax, Scutiger and, Vibrissaphora; (2) tribe Leptolalaxini,corresponding to the tadpole of novel type B, including two genera, i.e., Leptolalaxand Leptobrachella. However, the relationships among the genera of Megophryinaewere largely unresolved, they recognized no monophyletic groups above the generalevel. A more thorough sampling will likely foster a better taxonomic solution.3) The larval evolutionary scenario in Megophryidae.Type A is characteristicof normal-mouthed with multiple tooth rows, representing the tadpole type of theMRCA of Chinese megophryids. Type B is characteristic of normal-mouthed withreduced tooth rows, prolonging labium, and integumetary glands. Type C ischaracteristic of no labial teeth and smaller umbeliform oral disc. Type D ischaracteristic of no labial teeth, enlarged umbeliform oral disc, representing the tadpoleof the MRCA of subfamily Megophryinae. A previous hypothesis, referring tofunnel-shaped oral discs as an apomorphy, is supported.4) The larval adaptation to habitats in Megophryidae. Tadpoles generallyadhere to substrates using their mouths, and the microhabitat that the tadpoles occupyreflects the degree of adhesion and oral complexity. The morphological changes inmegophryid tadpoles virtually allow a progressive adaptation to a changing habitatfrom faster water to slower water. Within the tadpoles of Type A to type D, the TOTbecomes smaller and smaller, and the oral disc orientates from anteroventral toumbelliform upturned, and eye position orientates from dorsal to lateral, and the trunkis more and more depressed and tail becomes relatively longer and slender. Within therunning water, the normal-mouthed with multiple tooth rows of Leptobrachiini tadpoles are correlated with lotic-suctorial, benthic feeders with anteroventral oraldisc and the largest body. With the water’s velocity decreasing, the lotic-adherentfeeders of Leptolalax tadpoles have tube-shaped labium with reduced tooth rows andintegumetary glands. And then, the smaller umbeliform in Brachytarsophrys tadpolesand the enlarged umbeliform oral disc in the Megophryini tadpoles are inhabitmicrohabitats of non-flowing backwaters of rivers, indicative of adaptive traits oflotic-neustonic surface feeders. The scheme of megophryid tadpoles andmicrohabitats provided the first clear evidence which congruent with the hypothesis ofAltig and Johnston (1989). The ecological divergence plays a general role in thedivergence and evolution of megophrid larvae. There is a definite correlation amongthe buccopharyngeal cavity, diet and feeding mechanisms, the tadpole graze orswallow the food particles, then through papillae which like a sieve and sort out foodparticles to the oesophagus. The tadpole of Leptobrachiinae possess multiple toothrows, wide intertooth distance as well as thick and sparse jaw sheath, these tadpolesinhabit bottom of the streams and graze on epiphyton or major detritus of organicmatter on the substrates, their prelingual papillae like single finger, the mechanicalpurpose of papillae served share in by tooth and jaw. The tadpoles of Megophryinaeoccur near the water surface of small streams and are the filter feeder, their dietincludes plankton and organic debris floating on the water surface, those tadpolepossess weak jaw, their prelingual papillae like spoon, the mechanical purpose ofpapillae served mostly for sieve.

The level and distribution of chromosomal aberration of tomato seeds at different penetration depths of carbon ions

The relationship between the penetration depth and the level and distribution of chromosomal aberration of the root tip cells were investigated by exposure of the superposed tomato seeds to 80 MeV/u carbon ions. The results showed that on the entrance of the beam the chromosomal aberration level was low. Damage such as breaks and gaps were dominant. At the Bragg peak, the chromosomal aberration level was high. The yields of dicentrics, rings and disintegrated small chromosomes increased but the yields of breaks and gaps decreased. These results are consistent with the distribution of the physical depth dose pro. le of carbon ions. It is effective to deposit the Bragg peak on the seeds to induce hereditary aberration in the mutation breeding with heavy ions.

the ebb-tidal delta of the venice lagoon,Italy

Very high-resolution seismic lines were collected offshore the Venice Lagoon in the framework of the Co.Ri.La'New very high resolution seismic methods to study the Venice Lagoon subsoil' project. The 140 km boomer profiles led to the identification of a convex-upward,lens-shaped body just outside the Lido inlet,one of the three lagoon inlets,which has been interpreted as an ebb-tidal delta.The comparison between the scismostratigraphic setting og this deposit, as revealed by the seismic lines,and the analyses of historicalbathymetric maps highlighted the key role of human interventions in the formation and evolution of the Lido inlet cbb-tidal delta.To preserve the lagoon environment but also to ensure a navigable way, human interventions at the Lidoinlet,performed since the fourteenth centtury, caused profound variations in the inlet dynamics,ldading to a progressive increase in the sediment dispersion from the lagoon interior towards the sea. The ebb-tidal delta of the Lido nilet is thus a very recent feature compared with the formation of the Venice lagoon and formed mainly as a consequence of the construction of the two jetties that have bound the inlet form AD 1886 to the present day.

从沙尘暴看黄土的沉积及黄土高原的形成

以近年来我国西北地区多发的沙尘暴现象为缘起 ,对沙尘暴的特征、发生机制等进行了讨论 ;论述了沙尘暴引起的降尘与黄土的堆积和沉积的过程 ;黄土堆积沉积的年龄、颗粒成分等 ;以及沙尘暴与黄土高原的形成之间的关系 ,同时论述了黄土高原的环境变迁 .认为高空均质粉尘的降落是不均匀的 ;高空降尘是突发的 ,而风及流水对堆积粉尘的改造是长期和连续的

Electrochemical preparation of silver nanostructure on the planar surface for application in metal-enhanced fluorescence

We introduce a fast and simple method, named the potentiostatic electrodeposition technique, to deposit metal particles on the planar surface for application in metal-enhanced fluorescence. The as-prepared metallic surfaces were comprised of silver nanostructures and displayed a relatively homogeneous morphology. Atomic force microscopy and UV-visible absorption spectroscopy were used to characterize the growth process of the silver nanostructures on the indium tin oxide (ITO) surfaces. A typical 20-fold enhancement in the intensity of a nearby fluorophore, [Ru(bpy)(3)](2+), could be achieved on the silvered surfaces. In addition, the photostability of [Ru(bpy)(3)](2+) was found to be greatly increased due to the modification of the radiative decay rate of the fluorophore. It is expected that this electrochemical approach to fabricating nanostructured metallic surfaces can be further utilized in enhanced fluorescence-based applications.

Simple and convenient preparation of Au-Pt core-shell nanoparticles on surface via a seed growth method

Au-Pt core-shell nanoparticles were prepared on glass surface by a seed growth method. Gold nanoparticles were used as seeds and ascorbic acid-H2PtCL6 solutions as growth solutions to deposit Pt shell on the surface of gold nanoparticles. These core-shell nanoparticles and their growth process were examined by UV-Vis spectroscopy, X-ray photoelectron spectroscopy, atomic force microscopy and field-emission environmental scanning electron microscopy and the results indicated that the deposition speed was fast and nanoparticles with obvious core-shell structure could be obtained after 2 min. Moreover, this seed growth method for preparation of the core-shell nanoparticles is simple and convenient compared with other seed growth methods with NH4OH as a mild reductant. In addition, electrochemical experiments indicated that these Au-Pt core-shell nanoparticles had similar electrochemical properties to those of the bulk Pt electrode.

Electrochemical Metalloimmunoassay Based on Enlargement of Gold Nanoparticle Label Treated with Ag Enhancement System

A novel sensitive electrochemical immunoassay with colloidal gold as the antibody labeling tag and subsequent signal amplification by silver enhancement is described. Colloidal gold was treated by a light-sensitive silver enhancement system which made silver deposit on the surface of colloidal gold(form Au/Ag core-shell structure), followed by the release of the metallic silver atoms anchored on the antibody by oxidative dissolution of them in an acidic solution and the indirect determination of the dissolved Ag+ ions by anodic stripping voltammetry(ASV) at a carbon fiber microelectrode. The electrochemical signal is directly proportional to the amount of analyte(goat IgG) in the standard or a sample. The method was evaluated by means of a noncompetitive heterogeneous immunoassay of immunoglobulin G(IgG) with a concentration as low as 0.2 ng/ mL. The high performance of the method is related to the sensitive ASV determination of silver(I) at a carbon fiber microelectrode and to the release of a large number of Ag+ ions from each silver shell anchored on the analyte(goat IgG).

Carbon ceramic electrodes modified with sub-micron particles of new methylene blue (NMB) intercalated alpha-zirconium phosphate

New methylene blue-intercalated a-zirconium phosphate (NMBZrP) was synthesized in the presence of n-butylamine and characterized by powder XRD, FTIR, TEM and elemental analysis. Sub-micron particles of NMBZrP in deionized water were apt to deposit onto the surface of graphite powder to yield graphite powder-supported NMBZrP, which was subsequently dispersed into methyltrimethoxysilane-derived gels to fabricate surface-renewable, stable, rigid carbon ceramic electrodes containing new methylene blue. Cyclic voltammetric studies revealed that peak currents of the NMBZrP-modified electrode were surface-confined at low scan rates but diffusion-controlled. at high scan rates. In addition, NMBZrP immobilized in a carbon ceramic matrix presented a two-electron, three-proton redox process in acidic aqueous solution in the pH range from 0.52 to 3.95.

Isochiral form II of syndiotactic polypropylene produced by epitaxial crystallization

Epitaxial crystallization of syndiotactic polypropylene (sPP) on 2-quinoxalinol (2-Quin) yields, in the lower part of the crystallization range, the less common and metastable form II based on the packing of isochiral helices, rather than the stable antichiral form I. The contact plane is (110)(II). Form II exits only as a thin layer (< 50 nm) near the substrate surface. During further growth away from the surface, a transition takes place to the disordered form I, observed in "conventional" thin film growth. The epitaxial relationship rests only partly on dimensional matching with the chain axis repeat distance (which would be valid for both forms I and II) and on interchain distances. Whereas a better dimensional match would be achieved with form I, selection of the isochiral form II results from better correspondence of the surface topographies of the deposit (110)(II) sPP and substrate 2-Quin (001) contact faces.