Theoretical calculation of Flory-Huggins and scattering interaction parameters by means of the lattice fluid theory for PVME/PSD blends

By fitting the spinodals of poly(vinyl methyl ether)/deuterated polystyrene (PVME/PSD) systems, the adjustable parameters epsilon (12)* and delta epsilon* in the Sanchez-Balasz lattice fluid (SBLF) theory could be determined for different molecular weights. According to these parameters, Flory-Huggins and scattering interaction parameters were calculated for PVME/PSD with different molecular weights by means of the SELF theory. From our calculation, Flory-Huggins and scattering interaction parameters are both Linearly dependent on the reciprocal of the temperature, and almost linearly on the concentration of PSD. Compared with the scattering interaction parameters, the Flory-Huggins interaction parameters decreased more slowly with an increase in the concentration for all three series of blends.

Phase-separation behavior of the system PES/phenoxy: An application of the Sanchez-Lacombe lattice fluid theory

Cloud-point curves reported for the system polyethersulfone (PES)/phenoxy were calculated by means of the Sanchez-Lacombe (SL) lattice fluid theory. The one adjustable parameter epsilon(12)*/k (quantifying the interaction energy between mers of the different components) can be evaluated by comparison of the theoretical and experimental phase diagrams. The Flory-Huggins (FH) interaction parameters are computed based on the evaluated epsilon(12)*/k and are approximately a linear function of volume fraction and of inverse temperature. The calculated enthalpies of mixing of PES/phenoxy blends for different compositions are consistent with the experimental values obtained previously by Singh and Walsh [1].

Epitaxial crystallization of sPP on the (100) lattice plane of HDPE crystals

Crystallization behavior of syndiotactic polypropylene(sPP) on the (100) lattice plane of high-density polyethylene(HDPE) crystals was studied by means of transmission electron microscopy and electron diffraction. The results indicate that sPP crystals can grow epitaxially on the (100) PE lattice plane with their chain directions +/-37 degrees apart from the chain direction of the HDPE substrate. The contact planes are (100) lattice planes for both polymers. This kind of epitaxy is explained in terms of parallel alignment of HDPE chains along the rows formed by the {CH3, CH2,CH3} groups in the (100) lattice plane of the sPP crystals. This implies that in the epitaxial crystallization of sPP with fiber oriented HDPE substrate, not only the (110) but also the (100) HDPE lattice planes can act as the oriented nucleation sites. Furthermore, according to the poor matching between HDPE chains in the (100) lattice plane and the {CH3, CH2, CH3} group rows in the (100) lattice plane of the sPP crystals, it is concluded that the geometric matching is not the only controlling factor for the occurrence of polymer epitaxy.

Application of the Sanchez-Lacombe lattice fluid theory to the system pvme/ps and model calculations

Cloud point curves reported in the literature for five representatives of the system poly(vinyl methyl ether)/polystyrene were evaluated theoretically by means of the Sanchez-Lacombe lattice fluid theory. The measured phase separation behavior can be described within experimental error using only one adjustable parameter (quantifying the interaction between the unlike mers). The Flory-Huggins interaction parameters calculated from this theoretical description depend in good approximation linearly on composition (volume fractions) and on the inverse temperature. An evaluation of these data yields a maximum heat effect which is almost one order of magnitude less (ca. -0.25 J/cm(3)) than obtained via Hess's cycle (dissolution of the components and of the blend) from calorimetric measurements. Model calculations on the basis of the present theory demonstrate that the critical points shift to a different extent upon a certain relative change in the molar mass of the blend components. The sensitivity of the calculated phase diagrams against changes in the scaling parameter decreases in the following order: interaction energies between unlike mers, differences in the scaling temperatures, pressures and densities.

STATISTICAL THERMODYNAMICS IN THE FRAMEWORK OF THE LATTICE FLUID MODEL .1. POLYDISPERSE POLYMERS OF SPECIAL DISTRIBUTION

The Gibbs free energies and equations of state of polymers with special molar mass distributions, e.g., Flory distribution, uniform distribution and Schulz distribution, are derived based on a lattice fluid model. The influence of the polydispersity (or t

STATISTICAL THERMODYNAMICS IN THE FRAMEWORK OF THE LATTICE FLUID MODEL .2. BINARY MIXTURE OF POLYDISPERSE POLYMERS OF SPECIAL DISTRIBUTION

In this paper, the Gibbs free energy, the equation of state and the chemical potentials of polydisperse multicomponent polymer mixtures are derived. For general binary mixtures of polydisperse polymers, we also give the Gibbs free energy, the equation of

STATISTICAL THERMODYNAMICS IN THE FRAMEWORK OF THE LATTICE FLUID MODEL .3. BINARY MIXTURE OF POLYDISPERSE POLYMERS OF SPECIAL DISTRIBUTION WITH STRONG-INTERACTIONS

For a binary mixture of polydisperse polymers with strong interactions, the free energy, the equation of state, the chemical potentials and the spinodal are formulated on the basis of the lattice fluid model. Further, the spinodal curves for the system wi

CALCULATION METHOD OF LATTICE ENERGY ON COMPLEX-CRYSTALS

In this paper, based on the consideration of covalent behavior of adjacent ions in crystals, a calculation formula of lattice energy was proposed. In which, the concept of ionic effective valence and the empirical formula covalent energy were introduced,

STATISTICAL THERMODYNAMICS OF A LATTICE FLUID - PURE POLYMER

A statistical thermodynamics theory of a polydisperse polymer based on a lattice model of a fluid is formulated. The pure polydisperse polymer is completely characterized by three scale factors and the distribution law of the system. The equation of state does not satisfy a simple corresponding state principle, except for the polymer fluid with sufficiently high molecular weight.