鲜甘薯快速乙醇发酵条件的初步研究

本文对不同菌种（酵母菌和运动发酵单胞菌）快速生产燃料乙醇的条件进行了研究，实现了鲜甘薯快速转化为燃料乙醇。全文分为两部分： 第一部分：酵母菌快速生产燃料乙醇的条件研究。通过单因素试验，酵母菌快速生产燃料乙醇的条件为：发酵方式采用边糖化边发酵（SSF），蒸煮温度为85 ℃，料水比2:1（初始糖浓度 210 g/kg），糖化酶用量0.75 AGU/g 鲜甘薯，接种量10%（v/w）。在最优条件下，经过24 h发酵，乙醇浓度可达97.44 g/kg, 发酵效率为92%，发酵强度为4.06 g/kg/h。由于采用了低温蒸煮和SSF，可以大大节约能耗，从而降低乙醇生产的成本。同时，利用摇瓶优化的条件，进行了10 L，100 L，500 L发酵罐的放大试验，由于发酵罐初期可以人为通氧，使菌体能迅速积累，发酵时间缩短2 h，发酵效率在90%以上。 第二部分：运动发酵单胞菌快速生产燃料乙醇条件研究。通过单因素试验和正交试验获得了发酵的最佳参数：初始pH值6.0-7.0，硫酸铵5.0 g/kg，糖化酶量1.6 AUG/kg淀粉，初始糖浓度200 g/kg，接种量12.5%（v/w）。经过21 h发酵，乙醇浓度为95.15 g/kg，发酵效率可达94%。同时对不灭菌发酵也进行了研究，发酵效率可达92%。为鲜甘薯运动发酵单胞菌燃料乙醇的工业化生产打下基础。 对发酵结束后的残糖进行了研究。通过薄层层析和葡萄氧化酶测定证明：无论是酵母菌还是运动发酵单胞菌发酵结束后的发酵液中都不含葡萄糖。经过HPLC进一步分析残糖说明：发酵液中已没有葡萄糖成分；经糖化酶水解后仍没有葡萄糖出现；但经酸水解后又出现了葡萄糖，说明结束后的残糖是一些低聚糖结构。有关残糖的结构需要进一步研究。可以通过开发高效的低聚糖水解酶来降低发酵液的残糖，提高原料的利用率。 A new technology for rapid production fuel ethanol from fresh sweet potato by different microorganisms (Saccharomyces cerevisiae and Zymomonas mobilis) was gained in this research. The paper involved two parts: Part 1: The study on fuel ethanol rapid production from fresh sweet potato by Saccharomyces cerevisiae. The following parameters of Saccharomyces cerevisiae was investigated by a series of experiments: fermentation models, cooking temperature, initial sugar concentration and glucoamylase dosage. The results showed that SSF (simultaneous saccharification and fermentation) not only reduced the fermentation time (from 30 to 24h) but also enhanced the ethanol concentration (from 73.56 to 95.96 g/kg). With low-temperature-cooking (85 ℃) using SSF, the Saccharomyces cerevisiae was able to produce ethanol 97.44 g/kg which the fermentation yield could reach to 92% and ethanol productivity 4.06 g/kg/h from sweet potato enzymatic hydrolysis. Furthermore, the savings in energy by carrying out the cooking (85 ℃) and saccharification (30 ℃) step at low temperature had been realized. The results were also verified in 10 L, 100 L and 500 L fermentor. The fermentation yield was no less than 90%. The fermentation time of fermenter was shorter than Erlenmeyer flask. This may be that the aeration in the early fermentation period is available, which lead to the rapidly commutations of biomass. Part 2: The technology of ethanol rapid production with simultaneous saccharification and fermentation ( SSF ) by Zymomonas mobilis，using fresh sweet potato as raw material was studied. The effects of various factors on the yield of ethanol were investigated by the single factor and the orthogonal experiments. As a result, the optimal technical conditions were obtained from those experiments：initial pH value 6.0-7.0, nitride 5.0 g/kg，(NH4)2SO4, glucoamylase 1.6 AUG/kg starch, inoculums concentration 12.5% (v/w). The Zymomonas mobilis was able to produce ethanol 95.15 g/kg, with 94% of the theoretical yield, from fresh sweet potato after 24 h fermentation. The fermentation efficiency of non-sterilized was also reach to 92%. We also analyzed the final fermentation residual sugars of Saccharomyces cerevisiae and Zymomonas mobilis. When the residual sugars were analyzed by thin-layer chromatogram and glucose oxidase, there was no glucose. The analysis of reducing sugars by HPLC showed that there was no glucose existed in the fermentation liquor. However, the glucose appeared after being hydrolyzed by acid. It is indicated that the residual sugars in the final fermentation liquor were the configuration of oligosaccharide, which was linked by the special glycosidic bonds. It was feasible for reducing residual sugars to develope the enzyme that can degradation the oligosaccharide.

红发夫酵母发酵虾青素的研究

红发夫酵母分离于北美西部高山地区和日本一些岛屿上落叶树的渗出液中，因其所产主要色素为在水产养殖、食品和医药工业有广阔应用前景的虾青素而成为研究的热点。本论文对红发夫酵母Phaffia rhodozyma 的生长特性、培养参数与培养基组分对生长和虾青素积累的影响及其优化、虾青素合成的调节控制、虾青素的提取测定及红发夫酵母耐高温菌种的诱变进行了系统的研究。 虾青素是红发夫酵母的胞内色素，要对其进行分析首先要对红发夫酵母进行破壁处理，实验发现二甲亚砜是最有效的破壁溶剂，用氯仿和丙酮可以有效地把类胡萝卜素从二甲亚砜破壁后的红发夫酵母细胞中提取出来。 在固定摇床转速为200 rpm，温度为20 ℃的条件下，当种龄为36 h，以10％的接种量接入装液量为30 mL的250 mL三角瓶，初始pH为5.5时最有利于红发夫酵母的生长及类胡萝卜素的合成。 本实验中红发夫酵母最佳利用碳、氮源分别为蔗糖和蛋白胨，但蛋白胨价格昂贵，不适宜作单一氮源，因此使用硫酸铵和酵母膏作为复合氮源。 本论文采用了BP神经网络结合遗传算法的方法来优化红发夫酵母的发酵培养基，得到红发夫酵母发酵培养基的最佳配比为：蔗糖45.10 g/L、硫酸铵3.00 g/L、硫酸镁0.80 g/L、磷酸二氢钾1.40 g/L、酵母膏3.00 g/L、氯化钙0.50 g/L，使用优化后的培养基发酵类胡萝卜素产量达到8.20 mg/L，干重达到9.47 g/L，类胡萝卜素的产量比起始培养基提高了95.90%，干重提高了89.40%。 从代谢途径出发对红发夫酵母合成虾青素调控调控，选择谷氨酸、乙醇、VB1作为添加剂，通过正交试验设计得出三者添加水平分别为0.2 g/L，0.1% (V/V)，10 mg/L时，类胡萝卜素产量提高了25.73%，达到了10.31mg/L。 通过上述优化培养，本论文中红发夫酵母的虾青素产量从1.33 mg/L提高到9.12 mg/L，产量提高了6.86倍；总类胡萝卜素产量从4.23 mg/L提高到10.31 mg/L，产量提高了2.44倍；细胞干重从5.00 g/L提高到11.35 g/L，提高了2.27倍，总体提高效果显著。 红发夫酵母属于中低温菌，本论文采用紫外复合诱变的方式，通过高温筛选，得到一株能在35 ℃下能生长的突变株，但所产类胡萝卜素中虾青素所占比例很小，可能是诱变改变了红发夫酵母的代谢途径，阻断了虾青素的合成。 Phaffia rhodozyma is a heterobasidiomyceteous yeast that was originally isolated from the slime fluxes of brich tree wounds in mountain regions of northern Japan and southern Alaska. Phaffia rhodozyma produces astaxanthin as its principal carotenoid pigment, which has potential applications in acquaculture, food and pharmaceutical industry. This paper researched ways to break cell, analysis of astaxanthin, characteristics of growth, culture parameters and the effects of components of medium on growth and astaxanthin formation , optimization of culture medium, control of astaxanthin synthesis and mutagenesis of Phaffia rhodozyma. It is necessary to disrupt the yeast cell for extracting astaxanthin considering the yeast accumulating carotenoids in cell. Dimethyisulphoxide was the most effective solvent for breaking the yeast cell; acetone and chloroform were effective to extract carotenoids out of the disrupted cell. The optimum pH for growth and carotenoids synthesis is 5.5, the optimum medium volume is 30 mL (in 250 mL flask), the optimum culture time of inoculum is 36 h, the optimum inoculum concentration is 10%. The research on culture medium showed: sucrose is the best one of 6 carbon sources for growth and astaxanthin synthesis. Peptone is the best nitrogen source for growth and astaxanthin synthesis. Uniform Design was used for trial design of the formula medium components, then back-propagation neural network was established to modeling the relationships between the carotenoid yield and the concentration of medium components. Genetic algorithm (GA) was used for global optimization of the model. The optimum combination of the medium was obtained: sucrose 45.10 g/L, ammonium sulfate 3.00 g/L, magnesium sulfate 0.80 g/L, potassium dihydrogen phosphate 1.40 g/L, yeast extract 3.00 g/L, calcium chloride 0.50 g/L. The yield of carotenoid reached 8.20 mg/L, which was 95.90% higher than that of the original medium. Glu, VB1 and ethanol were selected as fermentation addictives, after Orthogonal Test, the carotenoid contents increased by 25.73% when adding 0.16 g/L Glu, VB1 10 mg/L and ethanol 0.1% (V/V). After the above optimization, the astaxanthin content increased 6.86 folds, which is 9.12 mg/L. The carotenoids content increased 2.44 folds, which is 10.31 mg/L. The biomass increased 2.27 folds, which is 11.35 g/L. Phaffia rhodozyma grows in the mild temperature range of 0 to 27 ℃, in this work, a thermotolerant mutant was selected through UV-irradiation. It can grows at 35 ℃, and showed increased carotenoid content. The optimal growth temperature for this mutant is 30 ℃. But the mutant can only produce carotenoids with little astaxanthin accumulation.

酿酒酵母和运动发酵单胞菌木薯乙醇发酵条件研究

本文结合我国燃料乙醇发展的方针政策，以酿酒酵母和运动发酵单胞菌为菌种研究其在非粮能源作物木薯中乙醇发酵的情况，为木薯原料更好地应用于生产中提供了理论依据。 酿酒酵母木薯高浓度乙醇发酵的研究。实验采用的木薯干淀粉含量约70-75%。以酿酒酵母为菌种进行高浓度乙醇发酵的工艺条件研究，最佳条件为：木薯干粉碎细度为35目，料水比1：2，α-淀粉酶用量0.09 KNU/g淀粉，蒸煮温度85 ℃，蒸煮时间15 min。采用30 ℃同步糖化发酵工艺，糖化酶用量为3.4 AGU/g淀粉，发酵时间30 h。在10 L发酵罐中，乙醇质量比达127.88 g/kg，发酵效率为88.28%，发酵强度4.263 g/kg/h，100 L中试研究中乙醇浓度为127.75 g/kg，发酵强度4.258 g/kg/h。利用高效液相色谱对发酵液中残糖进行了分析，证明葡萄糖、果糖等单糖已完全被菌体利用，剩余糖为二糖，三糖等不可发酵的低聚糖。 运动发酵单胞菌快速乙醇发酵的研究。对实验室保藏的8株运动发酵单胞菌进行比较，选择发酵速度最快的Zymomonas mobilis232B进行研究。该菌在纯葡萄糖中的最佳发酵条件为：葡萄糖浓度18%，起始pH 6-7，发酵温度30 ℃，发酵时间18 h，乙醇浓度88 g/kg。在以木薯为底物同步糖化快速乙醇发酵中，采用Full Factorial设计和最速上升实验确定了培养基成分中的2个显著性因子及其最适浓度：酵母粉4 g/kg，硫酸铵0.8 g/kg。在最适培养基条件下，对木薯料水比和糖化酶用量进行了优化，得到Z.mobilis232B木薯乙醇发酵最佳料水比1：3，糖化酶浓度4 AGU/g淀粉，乙醇发酵4.915 g/kg/h。利用高效液相色谱对发酵液中残糖进行了分析，剩余糖为二糖，三糖等，但成分较酵母发酵后复杂。 According to the fuel ethanol development plans and policies in our country, the ethanol production from cassava by Saccharomyces cerevisiae and Zymomonas mobilis was studied. It provided theoretical basis for ethanol fermentation by cassava in industry. Part 1 is the study of VHG (very high gravity) ethanol fermentation by Saccharomyces cerevisiae. The content of starch in cassava was 70-75%. Compared with the performances under different experimental conditions, the following optimal conditions for VHG fermentation were obtained: Granule size of dry cassava 35 mashes, hydromodulus of cassava to water at 1:2, α-amylase enzyme dosage 0.09 KNU/g starch, cooking temperature 85 ℃ for 15 min, using the SSF process (simultaneous saccharification and fermentation) and the amount of glucoamylase 3.4 AGU/g starch. Accordingly, the final ethanol concentration was up to 127.88 g/kg; the ethanol yield reached 88.28%, and ethanol productivity was 4.263 g/kg/h after 30 h. When the fermentation scale expanded to 100 L, the final ethanol concentration was 127.75 g/kg, and the ethanol productivity was 4.258 g/kg/h in 30 h. The residual sugar was analyzed by high performance liquid chromatography, and proved that there was no glucose and fructose. The residual reducing sugar was some unfermentable oligosaccharide Part 2 is the study of the rapid ethanol production by Zymomonas mobilis. Compare with other seven stains, Zymomonas mobilis 232B was selected for research. The optimum condition in glucose medium was as follow: glucose concentration 18%, initial pH 6-7, and fermentation temperature 30 ℃. The ethanol concentration was 88g/kg in 18 h. After that, rapid ethanol production from cassava in SSF by Zymomonas mobilis 232B was studied. Through a series of experiments aided by Full Factorial Design and steepest ascent search, the optimal concentration yeast extract and ammonium sulfate were determined: 4 g/kg and 0.8 g/kg, each. Under optimum medium conditions, the optimal hydromodulus of cassava to water and glucoamylase dosages were obtained: hydromodulus of cassava to water at 1:3 and glucoamylase dosages 4 AGU/g starch. The ethanol production reached 4.915 g/kg/h. The residual sugar was analyzed by HPLC, and proved that the residual reducing sugar was some unfermentable oligosaccharide，but the components were more complex than that fermentation by Saccharomyces cerevisiae.

非粮原料燃料乙醇发酵关键技术的研究

生物质燃料乙醇是一种高度清洁的交通液体燃料，是减少温室气体排放，缓解大气污染的最佳技术选择。以非粮原料生产燃料乙醇可以在进行能源生产的同时保证粮食安全，有利于产业的可持续发展。在众多的非粮原料中，甘薯是我国开发潜力最大的生物质能源作物之一。我国占世界甘薯种植总面积和产量的90％。同时，甘薯的单位面积燃料乙醇产量远大于玉米和小麦。其成本是目前酒精中最低廉的，因此利用甘薯生产乙醇是发展生物质燃料乙醇的首要选择。目前采用薯类全原料主要采用分批发酵生产乙醇，其技术水平低，发酵强度低，一般在0.7－2.5g/（L•h），乙醇浓度低，甘薯发酵乙醇为6－8％(v/v)，能耗高，环境负荷大，污染严重。针对上述问题，本文从菌株选育、原料预处理、中试放大、残糖成分分析等方面进行研究。 为了研究乙醇发酵生产规模扩大过程中，大型发酵罐底部高压条件下，CO2对酵母乙醇发酵的影响，我们通过CO2 加压的方法进行模拟试验，研究结果表明，发酵时间随压强的升高而逐渐延长，高压CO2 对乙醇发酵效率影响不大，在0.3 MPa 以下时，发酵效率均可达到90%以上。高压CO2 对发酵的抑制作用是高压和CO2 这两个因素联合作用的结果。高压CO2 条件下，酵母胞外酶和胞内重要酶类的酶活均表现出特征性。0.2 MPa 下，酶活性的变化趋势和0.1 MPa 条件下的较为一致。而0.3 MPa 下的酶活变化趋势与0.4 MPa 下的酶活更为接近。通过全基因表达分析发现在CO2 压力为0.3 MPa 下，乙醇发酵途径中多个基因表达量下调，同时海藻糖合成酶和热激蛋白基因表达量上调。 筛选耐高温的乙醇酵母菌株能够解决糖化温度和发酵温度不协调的矛盾，实现真正意义上的边糖化边发酵。高温发酵还能够降低发酵时的冷却成本，实现乙醇的周年生产。本研究筛选出一株高温发酵菌株Y-H1，进而我们对该菌株的胞外酶和胞内乙醇代谢重要酶类的酶活性进行了分析。结果表明Y-H1 能够在40 ℃条件下正常进行乙醇发酵，发酵33h，最终乙醇浓度达到10.7%（w/w），发酵效率达到90%以上。同时发酵液最终pH 在3.5 左右，显示菌株具有一定的耐酸性能力。同时观察到40 ℃下，菌株的胞外酶和胞内乙醇代谢重要酶类的酶活性发生了变化，乙醇发酵途径中关键酶基因表达下调，而海藻糖合成酶与热激蛋白基因表达量上调，这些结果为进一步研究酵母菌耐热调控机理提供了依据。 糖蜜是一种大规模工业生产乙醇的理想原料，本研究利用选育高浓度乙醇发酵菌株结合配套的发酵稳定剂，研究了糖蜜高浓度乙醇发酵情况。结果表明采用冷酸沉淀预处理糖蜜溶液，采用分批补料的发酵方式，乙醇浓度最高达到了10.26% (w/w)，发酵时间为42 h。同时观察到在糖蜜发酵中，乙醛含量与乙醇浓度存在一定的相关性。 快速乙醇发酵对于缩短乙醇生产周期、降低乙醇生产成本、减少原料腐烂损失具有重要意义。本研究诱变和筛选得到了一株快速乙醇发酵菌株10232B。在优化后的发酵条件下，采用10L 发酵罐进行分批乙醇发酵，经过18h,乙醇的最终浓度达到88.5g/L,发酵效率93.6%，平均乙醇生产速度达到4.92 g/L/h。此菌株在保持较高乙醇生产浓度的同时，拥有快速生产乙醇的能力，适合作为快速乙醇发酵生产菌种。 由于鲜甘薯具有粘度大的特点，传统液化糖化处理很难在短时间内充分糖化原料；高粘度的醪液也难以进行管道输送，容易堵塞管路；同时，也会降低后续的乙醇发酵效率。 本文采用了快速粘度分析法对鲜甘薯糊化粘度特性进行了分析，进而对预处理条件进行了研究，在最佳预处理条件下，糖化2h 后，醪液葡萄糖值最高可达99.3，粘度4.5×104 mPa.s，而采用传统糖化工艺，醪液DE 值仅为85.8，粘度大于1.0×105 mPa.s。 此预处理方法也可用于快速糖化不加水的醪液。后续的乙醇发酵试验表明，通过此预处理方法获得的糖化醪液对乙醇发酵无负面影响。 在前期已实现了实验室水平的鲜甘薯燃料乙醇快速乙醇发酵基础上，进一步将发酵规模扩大到500L，在中试水平上对甘薯乙醇发酵进行了研究。结果表明在500L 中试规模，采用边糖化边发酵（SSF）工艺，在料液比为3∶1，发酵醪液最高粘度为6×104mPa.s 条件下，发酵37h，乙醇浓度达到了12.7%（v/v），发酵效率91%，发酵强度为2.7 g/（L•h）。与目前国内的薯类乙醇发酵生产技术水平具有明显的优越性。 为研究甘薯、木薯乙醇发酵中残糖的组成，采用了高效液相色谱—蒸发光散射检测法，对乙醇发酵残糖进行了分析。结果表明，甘薯、木薯乙醇发酵残糖均为寡聚糖，主要由葡萄糖、木糖、半乳糖、阿拉伯糖和甘露糖构成。随着发酵时间延长，寡聚糖中的葡萄糖、半乳糖、甘露糖可被缓慢的水解释放。提高糖化酶量仅在一定程度上降低残糖，过量的糖化酶反而会导致残糖增加。同时发现3, 5-二硝基水杨酸法不能准确测定甘薯、木薯乙醇发酵中的残总糖含量。进一步筛选了两株残糖降解菌株，对甘薯乙醇发酵残糖的降解利用率均达到了40%以上，而且还能显著降低发酵醪液粘度。经形态学和rRNA ITS 序列分析，确定这两株菌分别属于为木霉属和曲霉属黑曲霉组。 通过对以甘薯原料为代表的非粮原料发酵技术研究开发，以期形成乙醇转化率高，能耗低，生产效率高、季节适应性好，原料适应性广，经济性强，符合清洁生产机制的燃料乙醇高效转化技术，为具有我国特色的燃料乙醇发展模式提供技术支持。 Sweet potato is one of the major feedstock for the fuel ethanol production in China. The planting area and the yield in China take 90% of the world. Sweet potato is an efficient kind of energy crops. The energy outcome per area is higher than corn or wheat. And the manufacture cost of ethanol is the lowest, compared with corn and wheat. So sweet potato is the favorable crop for the bioethanol production in China. However, the low-level fermentation technology restricts the development of ethanol production by sweet potato, including slow ethanol production rate, low ethanol concentration and high energy cost. To solve these problems, we conducted research on the strain breeding, pretreatment, pilot fermentation test and residual saccharides analysis. To study the impact of hyperbaric condition at bottom of the large fermentor on yeast fermentation, high pressure carbon dioxide (CO2) was adopted to simulate the situation. The results showed that the fermentation was prolonged with the increasing pressure. The pressure of CO2 had little impact on the ethanol yield which could reach 90% under the pressure below 0.3 MPa. The inhibition was combined by the high pressure and CO2. Under the high CO2 pressure, the extracellular and important intracellular enzyme activities were different from those under normal state. The changes under 0.1 MPa and 0.2 MPa were similar. The changes under 0.3 MPa were closer to those under 0.4 MPa. The application of thermotolerance yeast could solve the problem of the inconsistent temperature between fermentation and saccharificaton and fulfill the real simultaneous saccharification and fermentation. And it could reduce the cooling cost. A thermotolerance strain Y-H1 was isolated in our research. It gave high ethanol concentration of 10.7%（w/w）at 40 ℃ for 33 h. The ethanol yield efficiency was over 90%. At 40 ℃, the extracellular and important intracellular enzyme activities of Y-H1 showed the difference with normal state, which may indicate its physiological changes at the high temperature. Molasses is another feedstock for industrial ethanol production. By our ethanol-tolerance strain and the regulation reagents, the fermentation with high ethanol concentration was investigated. In fed-batch mode combined with cold acid deposition, the highest ethanol concentration was 10.26% (w/w) for 42h. The aldehyde concentration in fermentation was found to be related to ethanol concentration. The development of a rapid ethanol fermentation strain of Zymomonas mobilis is essential for reducing the cost of ethanol production and for the timely utilization of fresh material that is easily decayed in the Chinese bioethanol industry. A mutant Z. mobilis strain, 10232B, was generated by UV mutagenesis. Under these optimized conditions, fermentation of the mutant Z. mobilis 10232B strain was completed in just 18 h with a high ethanol production rate, at an average of 4.92 gL-1h-1 per batch. The final maximum ethanol concentration was 88.5 gL-1, with an ethanol yield efficiency of 93.6%. This result illustrated the potential use of the mutant Z. mobilis 10232B strain in rapid ethanol fermentation in order to help reduce the cost of industrial ethanol production. As fresh sweet potato syrup shows high viscosity, it is hard to be fully converted to glucose by enzymes in the traditional saccharification process. The high-viscosity syrup is difficult to be transmitted in pipes, which may be easily blocked. Meanwhile it could also reduce the later ethanol fermentation efficiency. To solve these problems, effects of the pretreatment conditions were investigated. The highest dextrose equivalent value of 99.3 and the lowest viscosity of 4.5×104 mPa.s were obtained by the most favorable pretreatment conditions, while those of 85.8 and over 1.0×105 mPa.s was produced by traditional treatment conditions. The pretreatment could also be applied on the material syrup without adding water. The later experiments showed that the pretreated syrup had no negative effect on the ethanol fermentation and exhibited lower viscosity. The fuel ethanol rapid production from fresh sweet potato was enlarged in the 500L pilot scale after its fulfillment on the laboratory level. The optimal ratio of material to water was 3 to 1 in 500L fermentor. With low-temperature-cooking (85 ℃) using SSF, the Saccharomyces cerevisiae was able to produce ethanol 97.44 g/kg for 37h, which reached 92% of theoretical yield. The average ethanol production rate was 4.06 g/kg/h. And the maximum viscosity of syrup reached 6×104mPa.s. The results showed its superiority over current industrial ethanol fermentation. The compositions of the residual saccharides in the ethanol fermentation by sweet potato and cassava were analyzed by high performance liquid chromatography coupled with evaporative light-scattering detector. The results showed that all the residual saccharides were oligosaccharides, mainly composed of glucose, xylose, galactose, arabinose and mannose. The glucose, galactose and mannose could be slowly hydrolyzed from oligosaccharides in syrup during a long period. To increase the glucoamylase dosage could lower the residual saccharides to a certain extent. However, excess glucoamylase dosage led to more residual saccharides. And the method of 3, 5-dinitrosalicylic acid could not accurately quantify the residual total saccharides content. Two residual saccharides degrading strains were isolated, which could utilize 40% of total residual saccharide and lower the syrup viscosity. With the analysis of morphology and internal transcribed spacer sequence, they were finally identified as species of Trichoderma and Aspergillus niger.

组合白腐真菌预处理木质纤维素原料的研究

木质纤维素原料种类多、分布广、数量巨大，通过燃料乙醇生产技术、厌氧沼气发酵技术将其转化成乙醇、沼气等二次能源，一定程度上可以缓解化石能源的不断消耗所带来的能源危机，也解决了农林废弃物引起的环境污染问题。其中以木质纤维素原料生产燃料乙醇，还可以避免以淀粉类和糖类原料生产燃料乙醇时带来的“与人争粮”等一系列问题。因此具有重要的经济效益、环境效益和社会效益。 然而，木质纤维素原料结构致密，木质素包裹在纤维素、半纤维素外围，导致其很难被降解利用，必须进行适当的预处理，去除木质素，打破原有的致密结构，利于原料的后续利用。因此，预处理成为木质纤维素原料能源化利用的关键。而目前预处理环节的费用过于昂贵，于是寻找一种高效、低成本的预处理方法是当今研究的热点。 本论文采用组合白腐真菌对木质纤维素原料进行生物预处理研究，与其他物理化学法相比，该法有着专一性较强、反应温和、不造成环境污染、成本低等优势。白腐真菌主要通过分泌木质素降解酶对木质素进行降解，从而破坏原料的致密结构，提高后续利用效率。所以木质素降解酶酶活的高低是影响原料预处理效果的一个关键因素。于是本论文首先通过将白腐真菌进行组合的方式提高木质素降解酶（漆酶，Lac）酶活；接着对组合菌的菌株相互作用机理进行研究，阐明组合菌Lac 酶活提高的原因，为菌株组合提高Lac 酶活这种方法的应用提供理论依据，同时也为后续组合白腐真菌预处理木质纤维素原料提供指导；进一步采用固态发酵和木质素降解酶两种方式对木质纤维素原料进行预处理研究，最大化去除木质素成分，破坏原料的致密结构；最终对预处理后原料的酶解糖化进行初步研究，为原料后续的能源化应用奠定基础。具体研究结果如下： （1） 以实验室保存的三株主要分泌Lac 的白腐真菌为出发菌株，筛选得到一组Lac 酶活明显提高的组合菌55+m-6，其中菌株55 为Trametes trogii sp.，m-6 为Trametes versicolor sp.，组合后Lac 酶活较单菌株分别提高24.13倍和4.07 倍。组合菌的最适产酶条件为pH 6.5、C/N 16:1、Tween 80 添加量为0.01%，在该条件下组合菌的Lac 酶活峰值比未优化时提高4.11倍。 （2） 对组合菌55+m-6 菌株间相互作用机理进行研究，发现菌株之间不存在抑制作用；平板培养时，菌丝交界处Lac 酶活最高并分泌棕色色素；液体培养时，菌株m-6 对组合后Lac 酶活的提高起着更为重要的作用：菌株m-6的菌块、过滤灭菌胞外物以及高温灭菌胞外物均能明显刺激菌株55 的Lac产生；菌株55、m-6 进行组合后，同工酶种类未发生增减，但有三种Lac同工酶浓度有所提高；对菌株胞外物进行薄层层析和质谱分析，结果表明组合前后菌株胞外物中各物质在浓度上存在较大的变化。推测组合菌Lac酶活的明显提高，主要是由于菌株m-6 胞外物中的一些物质能刺激菌株55 分泌大量Lac 进行代谢，且这些刺激物质并非菌株m-6 特有，菌株55自身也可以代谢生成，但是适当的浓度才能刺激Lac 的大量分泌。 （3） 将组合菌55+m-6 用于固态发酵预处理木质纤维素原料，发现其对玉米秆的降解程度最大，在粉碎度40 目、含水率65%的最优处理条件下，处理至第15d，秸秆失重率为41.24%，其中木质素、纤维素、半纤维素均有降解，且Lac 和纤维素酶（CMC）酶活以及还原糖量均达到峰值。 （4） 对玉米秆进行木质素降解酶预处理，发现Lac/1-羟基苯并三唑（HBT）系统对玉米秆木质素的降解效果最好，在最优处理条件时，即HBT 用量0.2%、处理时间1d、Lac 用量50U/g，木质素降解率可达12.60%。预处理后玉米秆的致密结构被破坏，比表面积增大，利于后续酶与纤维素、半纤维素成分的结合。 （5） 对预处理后的玉米秆进行酶解糖化，其中组合菌固态发酵预处理后玉米秆的糖化率比对照高4.33 倍；Lac/HBT 系统预处理后玉米秆的糖化率比对照高2.99％，糖化液中主要含有木糖、葡萄糖两种单糖。 There are many kinds and large quantities of lignocellulosic biomass widely distributed on the earth. They can be converted into secondary energy such as fuel ethanol, biogas, et al., which can relieve the energy crisis caused by consumption of fossil energy resources and solve the problem of environmental pollution caused by agriculture and forestry waste. Meanwhile, the production of fuel ethanol from lignocellulosic biomass can ensure food supply to human kind instead of starch- and sugar-containing raw materials. So the energy conversion of lignocellulosic biomass contributes considerable economic, environment and social benefits. However, lignocellulosic biomass has the compact structure, in which lignin surrounds cellulose and hemicellulose, so it must be pretreated before energy usage and pretreatment is one of the most critical steps in the energy conversion of lignocellulosic biomass. At present, the cost of pretreatment is too expensive, so looking for an efficient and low-cost pre-treatment method is one of recent research hot spots. In this research, combined white rot fungi pretreatment method was used, which had some advantages in low cost, high specificity, mild reacting conditions and friendly environmental effects compared with the other physical and chemical methods. White rot fungi secrete lignin degrading enzymes to degrade the content of lignin and damage the contact structure of lignocellulosic biomass, so the activity of the lignin degrading enzymes is the key factor to the degradation effect of raw materials. Firstly, the combined fungi with high laccase activity were screened; secondly, the interaction mechanism between strains was studied, and the cause of higher laccase activity after strains combination was also preliminary clarified; under the guidance of the mechanism, lignocellulosic biomass was pretreated by the combined fungi; lastly, the enzymatic hydrolysis of pretreated lignocellulosic biomass was also preliminary studied; all of the researches could lay the foundation for the energy application of lignocellulosic biomass. The specific research results were as follows: (1) The combined fungi 55+m-6 with significant higher laccase activity were screened from the three white rot fungi stored in our lab which mainly secreted laccase. Strain 55 and strain m-6 were Trametes trogii sp. and Trametes versicolor sp., respectively. The laccase activity of combined fungi was 24.13 and 4.07-fold than strain 55 and strain m-6, respectively. The optimized condition for laccase production of the combined fungi in liquid medium was pH 6.5, C/N 16:1 and Tween 80 0.01%. In this optimized condition, the laccase activity of combined fungi was 4.11-fold higher comparing with which in non-optimized medium. (2) The interaction mechanism between strain 55 and strain m-6 was further studied, and no inhibition effect was observed. Brown pigment was secreted on the junction of the two strains on the plate, where the highest laccase activity was detected. Strain m-6 was much important to boost laccase activity of combined fungi in liquid medium, and strain 55 was stimulated by fungal plug, filter sterilized extracellular substances and high temperature sterilized extracellular substances of strain m-6 to produce laccase. The types of laccase isozymes did not change after combining strain 55 and strain m-6, but the concentrations of three types increased. Mass Spectrometry and TLC analysis of extracellular substances of each strain showed that concentration of some substances considerably changed after strains were combined. It was supposed that the cause of higher laccase activity of combined fungi was mainly due to some extracellular substances of strain m-6 with the appropriate concentration which stimulated laccase secretion of strain 55 and generated not only by strain m-6 but also by strain 55. (3) Combined fungi 55+m-6 were used to lignocellulosic biomass pretreatment with the type of solid-state fermentation. The highest degree of degradation of corn straw was obtained, including the rate of weight loss was 41.24% and the lignin, cellulose and hemicellulose were degraded partially under the optimized condition of 40 mesh, 65% water content on 15th day. Laccase, CMCase activities and content of reducing sugar reached the maximum value on that day. (4) Lignin degrading enzymes from combined fungi 55+m-6 were used for corn straw pretreatment. The most remarkable degradation of lignin in corn straw with Lac/1-hydroxybenzotriazole (HBT) system was observed, and the 12.60% lignin degradation was obtained under the optimized condition of 0.2% HBT, 50 U/g laccase for 1 d. After pretreated by Lac/HBT, the tight structure of corn straw was demolished and specific surface area increased, which had advantages for accessible of enzyme to cellulose and hemicellulose. (5) The corn straws pretreated by combined fungi 55+m-6 with the type of solid-state fermentation and Lac/HBT were used for enzymatic hydrolysis, and the saccharification rates of each pretreatment type were 4.33 times and 2.99% higher than CK, respectively. The enzymatic hydrolysis liquid of corn straw pretreated by Lac/HBT mainly contained xylose and glucose.

一株丝状真菌对半纤维素利用的初步研究

本文筛选出一株能利用木糖产乙醇的丝状真菌Z7，对其利用木糖和半纤维素水解产物产乙醇的发酵条件进行了研究，并对Z7 利用玉米芯产木聚糖酶的条件进行了优化。全文分为三部分： 第一部分：目标微生物筛选、纯化及系统发育分析。以木糖为唯一碳源，采用梯度稀释和平板化线法从高温、中温酒曲中分离到16 株能利用木糖良好生长的丝状真菌；通过发酵试验复筛，获得一株能产乙醇的丝状真菌Z7；综合形态学和ITS 序列分析，初步鉴定为Aspergillus flavus。 第二部分：Z7 的乙醇发酵条件研究。以木糖为碳源，通过单因素试验确定最佳氮源和发酵温度；通过正交试验及SPSS 软件分析得到了不同N、P、K 成分对乙醇、残糖和菌体干重的影响。获得最佳的发酵条件为：（g/L）木糖50，尿素1, NH4NO3 1, K2HPO4 2 , KCl 0.5 , MgSO4.7H2O 0.5 , NaNO3 1 , pH 自然，培养温度33 ℃。以玉米芯半纤维素稀酸水解液为底物进行乙醇发酵，根据稀酸水解的单糖释放量和乙醇产量，确定115 ℃，1 h 为最佳玉米芯预处理条件；结合最佳发酵条件，添加1 g/L 的吐温20 能获得最大的乙醇浓度8.31 g/L。因此，Aspergillus flavus Z7 能利用半纤维素水解产物产乙醇，其中木糖的利用率80%以上。 第三部分：Z7 利用玉米芯产木聚糖酶条件优化。Aspergillus flavus Z7 在具有产乙醇能力的同时还具有产木聚糖酶的能力。本文通过单因素和正交试验得到最佳产酶培养基组分为：(g/L)玉米芯20，尿素2, 酵母膏2.5, K2HPO4 5，NaNO31, MgSO4.7H2O 1。单因素试验表明，用纱布代替塑料布密封摇瓶封口能显著提高产酶量；Z7 在碱性条件下具有更强的产酶性能。在最优条件下发酵，能产生最大木聚糖酶活122.23IU/mL。通过薄层分析，验证了Z7 产生的木聚糖酶具有水解木聚糖生成木糖及木寡糖的能力。 A strain of filamentous fungus which can produce ethanol by using the xylose was isolated in this research. The ethanol fermention conditions from xylose and dilute-acid hydrolyzate of the corn core were studied. The conditions of xylanase production by Z7 were also optimized. The paper involved three parts. Part1: Isolation, purification and phylogenetic analysis of the microbe. By using xylose as the single carbon source and the pla te streaking method, several filamentous fungi were isolated from the wine starter; through the fermentation test, a filamentous fungus Z7 which can produce ethanol was further recognized; furthermore, according to the morphologic observation and ITS seque nces analysis, Z7 was identified as Aspergillus flavus at the first step. Part2: Research on the condition of ethanol fermentation by Z7. By single factor experiment, the optional nitrogen resource and temperature of the fermentation were fixed; meanwhile, through the orthogonal array tests and the analysis of statistic software SPSS, the optional component of the culture medium and the fermentation condition were organized as follows: (g/L) xylose 50, urea 1, NH4NO3 1, K2HPO4 2, KCl 0.5 , MgSO4.7H2O 0.5, NaNO31, pH nature, temperature 33℃. Based on these optimal parameters, the fermentation of dilute-acid hydrolyzate of the corn core was carried on by Z7. According to the quantities of released sugar monomers and content of the ethanol, 115℃ in 1h is the best pretreatment condition; the maximal ethanol content can be obtained when 1g/L Tween 20 was added to. Therefore, the filamentous fungus Aspergillus flavus can use the hydrolysate of hemicellulose to produce ethanol, and the rate of xylose utilization was over 80%. Part3: Optimization of Z7’s xylanase producing condition from corn core. Aspergillus flavus Z7, which can utilize xylose or the hydrolysate of hemicellulose to produce ethanol, also had the ability of xylanase production. The optional component of the culture medium were fixed by the single factor experiment and the orthogonal array tests, and they were organized as follows: (g/L) corn core 20, Urea 2, Yeast extract 2.5, K2HPO4 5, NaNO31, MgSO4.7H2O 1; it was testified by the single factor experiment that sealing the shaking flasks with pledget other than plastic paper can obviously increase the xylanase activity; moreover, Z7 showed better xylanase production ability when in the alkali environment. Under the optional fermentation condition, the maximal xylanase activity 122.23IU/mL was proved. Through the analysis of thin- layer chromatography (TLC), the ability of xylanase from Z7, which can hydrolyze xylan to xylose monomer and oligomer, was vividly displayed.

Experimental studies of the dissociative recombination of CD3CDOD+ and CH3CH2OH2+

Aims. We determine branching fractions, cross sections and thermal rate constants for the dissociative recombination of CD3CDOD+ and CH3CH2OH2+ at the low relative kinetic energies encountered in the interstellar medium. Methods. The experiments were carried out by merging an ion and electron beam at the heavy ion storage ring CRYRING, Stockholm, Sweden. Results. Break-up of the CCO structure into three heavy fragments is not found for either of the ions. Instead the CCO structure is retained in 23 +/- 3% of the DR reactions of CD3CDOD+ and 7 +/- 3% in the DR of CH3CH2OH2+, whereas rupture into two heavy fragments occurs in 77 +/- 3% and 93 +/- 3% of the DR events of the respective ions. The measured cross sections were fitted between 1-200 meV yielding the following thermal rate constants and cross-section dependencies on the relative kinetic energy: sigma(E-cm[eV]) = 1.7 +/- 0.3 x 10(-15)(Ecm[eV])(-1.23 +/- 0.02) cm(2) and k(T) = 1.9 +/- 0.4 x 10(-6)(T/300)-0.73 +/- 0.02 cm(3) s(-1) for CH3CH2OH2+ as well as k(T) = 1.1 +/- 0.4 x 10(-6)(T/300)(-0.74 +/- 0.05) cm(3) s(-1) and s(Ecm[eV]) = 9.2 +/- 4 x 10(-16)(Ecm[eV])-1.24 +/- 0.05 cm(2) for CD3CDOD+

Performance comparison of low-temperature direct alcohol fuel cells with different anode catalysts

Low-temperature polymer electrolyte membrane fuel cells directly fed by methanol and ethanol were investigated employing carbon supported Pt, PtSn and PtRu as anode catalysts, respectively. Employing Pt/C as anode catalyst, both direct methanol fuel cell (DMFC) and direct ethanol fuel cell (DEFC) showed poor performances even in presence of high Pt loading on anode. It was found that the addition of Ru or Sn to the Pt dramatically enhances the electro-oxidation of both methanol and ethanol. It was also found that the single cell adopting PtRu/C as anode shows better DMFC performance, while PtSn/C catalyst shows better DEFC performance. The single fuel cell using PtSn/C as anode catalyst at 90degreesC shows similar power densities whenever fueled by methanol or ethanol. The cyclic voltammetry (CV) and single fuel cell tests indicated that PtRu is more suitable for DMFC while PtSn is more suitable for DEFC. (C) 2003 Elsevier B.V. All rights reserved.

Effects of zirconia phase on the synthesis of higher alcohols over zirconia and modified zirconia

The catalytic performances of ZrO2-based catalysts were evaluated for the synthesis of higher alcohols from synthesis gas. The crystal phase structures were characterized by X-ray diffraction (XRD) and UV Raman. The results indicated that ZrO2 and Pd modified ZrO2 catalysts were effective catalysts in the synthesis of ethanol or isobutanol, and their selectivities basically depended on the crystal phase of ZrO2 surface. The ZrO2 with surface tetragonal crystal phase exhibited a high activity to form ethanol, while the ZrO2 with surface monoclinic crystal phase exhibited a high activity to form isobutanol. Temperature-programmed desorption (TPD) experiment indicated that the high activity of isobutanol formation from synthesis gas over monoclinic zirconia was due probably to the strong Lewis acidity of Zr4+ cations and the strong Lewis basicity of O2- anions of coordinative unsaturated Zr4+-O2- pairs on the surface of monoclinic ZrO2. (C) 2003 Elsevier B.V. All rights reserved.

Thermodynamic investigation on properties of gasohol

The heat capacities (C-p) of three types of gasohol (which consisted of 20 wt % ethanol and 80 wt % unleaded gasoline 93(#) (system S1), 30 wt % ethanol and 70 wt % unleaded gasoline 931 (system S2), 40 wt % ethanol and 60 wt % unleaded gasoline 930 (system S3), where "93(#)" denotes the octane number) were measured by adiabatic calorimetry in the temperature range of 80320 K. A glass transition was observed at 94.24, 95.15, and 95.44 K for system S1, S2, and S3, respectively. A solid-solid phase transition and solid-liquid phase transition were observed at 135.18 and 151.30 K for system S1, 131.82 and 152.10 K for system S2, and 121.29 and 155.09 K for S3, respectively. The polynomial equations for C, with respect to the thermodynamic temperature (T), and with respect to the content of ethanol (x), were established through the least-squares fitting. The thermodynamic functions and the excess thermodynamic functions of the three samples were derived using these thermodynamic relationships and equations.

Influence of drying method on morphology and properties of asymmetric cellulose hollow fiber membrane

Using a dry/wet spinning process, asymmetric cellulose hollow fiber membranes (CHFM) were prepared from a dope composed of cellulose/N-methylmorpholine-N-oxide/water. The formation mechanism for the finger-like macrovoids at the inner portion of as-spun fibers was explained. Naturally drying and three solvent exchange drying methods were tried to investigate their influence on morphology and properties of CHFM. It was found that the ethanol-hexane exchange drying was an appropriate method to minimize morphology change of the as-spun CHFM, whereas the naturally drying caused the greatest shrinkage of the fibers that made the porous membrane become dense. The result, CHFM from ethanol-hexane exchange drying performed the highest gas permeation rate but gas permeation of the naturally dried membrane could not be detectable. The resultant CHFM from the ethanol-hexane exchange drying also showed acceptable, mechanical properties, thus it was proposed to be an appropriate method for gas separation purpose. The experimental results supported the proposed drying mechanism of CHFM. The free water would evaporate or be replaced by a solvent that subsequently would evaporate but the bonded water would remain in the membrane. What dominated the changes of membrane morphology during drying should be. the molecular affinities of cellulose-water, water-solvent and solvent-solvent. (C) 2004 Elsevier B.V. All rights reserved.

Study of an electroosmotic pump for liquid delivery and its application in capillary column liquid chromatography

A packed-bed electroosmotic pump (EOP) was constructed and evaluated. The EOP consisted of three capillary columns packed in parallel, a gas-releasing device, Pt electrodes and a high-voltage power supply. The EOP could generate output pressure above 5.0 MPa and constant flow rate in the range of nl/min to a few mul/min for pure water, pure methanol, 2 mM potassium dihydrogenphosphate buffer, the buffer-methanol mixture and the pure water-methanol mixture at applied potentials less than 20 W The composition of solvent before/after pumping was quantitatively determined by using a gas chromatograph equipped with both flame ionization detector and thermal conductivity detector. It was found that there were no apparent changes in composition and relative concentrations after pumping process for a methanol-ethanol-acetonitrile mixture and a methanol-water mixture. Theoretical aspect of the EOP was discussed in detail. An capillary HPLC system consisting of the EOP, an injection valve, a 15 cm x 320 mum i.d., 5 mum Spherigel C(18) stainless steel analytical column, and an on-column UV detector was connected to evaluate the performance of the EOP. A comparative study was also carried out with a mechanical capillary HPLC pump on the same system. The results demonstrated that the reproducibility of flow rate and the pulsation-free flow property of the EOP are superior to that of mechanical pump in capillary HPLC application. (C) 2004 Elsevier B.V. All rights reserved.

Difference of ZSM-5 zeolites synthesized with various templates

ZSM-5 zeolites with similar SUM ratio were synthesized successfully using various templates (n-butylamine (BTA), ethylamine (ETA), isopropylamine (IPA), ethylenediamine (EDA), ethanol (ETL), ethanol-ammonium (ETL-AM) and no template (NT)) under hydrothermal conditions. The samples were characterized by XRD, SEM, XRF, NH3-TPD and BET surface area measurements in order to understand the template effects and the differences of the ZSM-5 samples. The synthesis of ZSM-5 with organic templates was relatively easier than those with inorganic templates and without template. SEM results revealed that ZSM-5 synthesized with different templates had different morphology and particle size. The Si/Al ratio and BET specific surface area of the sample with ethanol as template was the lowest. NH3-TPD results showed that the sample synthesized without template had fewer strong acid sites than others. n-Hexane cracking reaction was carried out over the samples to evaluate the catalytic properties. All ZSM-5 zeolites were effective in n-hexane cracking reaction, especially for the sample synthesized without template. (C) 2004 Elsevier B.V. All rights reserved.

Synthesis and surface characteristics of zirconia and modified zirconia: Performance of CO hydrogenation

ZrO2-A and ZrO2-B catalysts were prepared by two different coprecipitation methods and their performance of CO hydrogenation was studied. The results indicated that ZrO2 and Li-, Pd- and Mn-modified ZrO2 catalysts exhibited good selectivity and high STY to higher alcohols. The surface characteristics of ZrO2-A and ZrO2-B samples were investigated by means of BET, NH3-TPD, XRD and UV Raman technique. The tetragonal zirconia on the surface region of ZrO2-A and Li-Pd-Mn/ZrO2-A catalysts may be responsible for the high selectivity towards ethanol, while the monoclinic zirconia on the surface of ZrO2-B and Li-Pd-Mn/ZrO2-B catalysts may be crucial to the high isobutanol selectivity.

Capillary electrochromatographic separation of enantiomers on chemically bonded type of cellulose derivative chiral stationary phases with a positively charged spacer

Positively charged chiral stationary phases (CSPs) were prepared for capillary electrochromatography (CEC) separation of enantiomers by chemically immobilizing cellulose derivatives onto diethylenetriaminopropylated silica (DEAPS) with tolylene-2,4-diisocyanate (TDI) as a spacer reagent. Anodic electroosmotic mobility was observed in both nonaqueous and aqueous mobile phases due to the positively charged amines on the surface of the prepared CSPs. For comparison, the traditionally used 3-aminopropyl silica (APS) was also adopted as the base material instead of DEAPS to prepare CSP. It was observed that the EOF on the DEAPS-based CSP was 18%-60% higher than that on the APS-based CSP under nonaqueous mobile phase conditions. Separation of enantiomers in CEC was performed on the positively charged CSPs with the nonaqueous mobile phases of pure ethanol or mixture of hexane-alcohol and the aqueous phases of acetonitrile-water or 95% ethanol. Fast separation of enantiomers was achieved on the newly prepared CSPs.