Scattering of linear water waves by a fixed and infinitely long rectangular structure parallel to a vertical wall in oblique seas

The scattering of linear water waves by an infinitely long rectangular structure parallel to a vertical wall in oblique seas is investigated. Analytical expressions for the diffracted potentials are derived using the method of separation of variables. The unknown coefficients in the expressions are determined through the application of the eigenfunction expansion matching method. The expressions for wave forces on the structure are given. The calculated results are compared with those obtained by the boundary element method. In addition, the influences of the wall, the angle of wave incidence, the width of the structure, and the distance between the structure and the wall on wave forces are discussed. The method presented here can be easily extended to the study of the diffraction of obliquely incident waves by multiple rectangular structures.

Response amplitude and hydrodynamic force for a buoy over a convex

A buoy as an offshore structure is often placed over a convex such as a caisson or a submerged island. The hydrodynamic fluid/solid interaction becomes more complex due to the convex compared with that on the flat. Both the buoy and the convex are idealized as vertical cylinders. Linear potential theory is used to investigate the response amplitude and the hydrodynamic force for a buoy over a convex due to diffraction and radiation in water of finite depth. These are derived from the total velocity potential. A set of theoretical added mass, damping coefficient, and exciting force expressions have been proposed. Analytical results of the response amplitude and hydrodynamic force are given. Finally, the numerical results show that the effect of the convex on the response amplitude and hydrodynamic force for the buoy is ignored if the size of the convex is relatively smaller.

单向流作用下近壁面圆柱的流向振动

在单向流水槽中对近壁面圆柱体的流向振动进行了实验模拟.分析了圆柱流向振动位移时程曲线,探讨了圆柱振动频率随水流速度的变化特征.研究了圆柱振动幅值和频率的变化特性,结合圆柱尾迹涡的变化规律,分析了流向振动的起因.实验结果表明:随着流速的增加,圆柱流向振动经历了发生、发展和消失的变化过程,振动频率呈现出缓慢增长的趋势;在流向振动触发初期和后期衰退时,流向振动频率存在多值现象,频谱中呈现多个谱峰:圆柱流向振动所对应的约减速度范围明显小于横向涡激振动所对应的范围.

PREDICTION OF VORTEX-INDUCED VIBRATION OF FLEXIBLE RISER USING AN IMPROVED WAKE-OSCILLATOR MODEL

Based on improving the wake-oscillator model, an analytical model for vortex-induced vibration (VIV) of flexible riser under non-uniform current is presented, in which the variation of added mass at lock-in and the nonlinear relationship between amplitude of response and reduced velocity are considered. By means of empirical formula combining iteration computation, the improved analytical model can be conveniently programmed into computer code with simpler and faster computation process than CFD so as to be suitable to application of practical engineering. This model is validated by comparing with experimental result and numerical simulation. Our results show that the improved model can predict VIV response and lock-in region more accurately. At last, illustrative examples are given in which the amplitude of response of flexible riser experiencing VIV under action of non-uniform current is calculated and effects of riser tension and flow distribution along span of riser are explored. It is demonstrated that with the variation of tension and flow distribution, lock-in region of mode behaves in different way, and thus the final response is a synthesis of response of locked modes.

INVESTIGATING A NEAR-BED SUBMARINE PIPELINE IN A CURRENT

This paper considers the lift forces acting on a pipeline with a small gap between the pipeline and the plane bottom or scoring bottom. A more reasonable fluid force on the pipeline has been obtained by applying the knowledge of modified potential theory (MPT), which includes the influences of the downstream wake. By finite element method, an iteration procedure is used to solve problems of the nonlinear fluid-structure interaction. Comparing the deflection and the stress distributions with the difference sea bottoms, the failure patterns of a spanning pipeline have been discussed. The results are essential for engineers to assess pipeline stability.

Numerical simulation of thermal loading produced by shaped high power laser onto engine parts

Recently a new method for simulating the thermal loading on pistons of diesel engines was reported. The spatially shaped high power laser is employed as the heat source, and some preliminary experimental and numerical work was carried out. In this paper, a further effort was made to extend this simulation method to some other important engine parts such as cylinder heads. The incident Gaussian beam was transformed into concentric multi-circular patterns of specific intensity distributions, with the aid of diffractive optical elements (DOEs). By incorporating the appropriate repetitive laser pulses, the designed transient temperature fields and thermal loadings in the engine parts could be simulated. Thermal-structural numerical models for pistons and cylinder heads were built to predict the transient temperature and thermal stress. The models were also employed to find the optimal intensity distributions of the transformed laser beam that could produce the target transient temperature fields. Comparison of experimental and numerical results demonstrated that this systematic approach is effective in simulating the thermal loading on the engine parts. (C) 2009 Elsevier Ltd. All rights reserved.

Design of a 7 T Superconducting Magnet for Lanzhou Penning Trap

A penning trap system called LPT (LANZHOU PENNING TRAP) is now being developed for precise mass measurements in IMP (Institute of Modern Physics). The most key component of LPT is a superconducting magnet. A Phi 156 mm warm bore and two cylinder good field regions with a distance of 220 mm are required for trapping ions and measurements. As the required homogeneity is better than 0.5 ppm, several complicated coaxial coils are used to produce such a magnetic field. The size and position of these coils are optimized by using a method combining linear program with multiobjective optimization. Superconducting shim coils and passive shim pieces are used to eliminate inevitable winding tolerances and environmental influence. The fringe field is decreased to 5 Gs at 2 m line from the center of the magnet by active shielding coils. The designs of the mechanical structure, the quench protection system are also introduced in this paper.

AlCl_3对细颗粒泥沙絮凝沉降的影响

铝类絮凝剂对细颗粒泥沙絮凝沉降有重要作用 ,常应用于浑水澄清、农业污水处理等研究中。在AlCl3 浓度为 0～ 1 7mmol/L ,泥沙浓度为 1 0g/L时 ,用吸管法研究了AlCl3 对细颗粒泥沙絮凝沉降的影响 ,结果表明 :在液面下同一深度 ,泥沙浓度随时间呈指数衰减 ;悬液经多次搅拌后再沉降 ,其沉速减缓 ;当AlCl3 浓度为 0 9～ 1 7mmol/L时 ,出现明显的清浑水交界面 ,交界面随时间等速下降 ,平均沉速为 4 75 6cm/min ,对应的絮团平均粒径为 0 0 31 5mm ;土娄土絮凝临界粒径为 0 0 2 7mm。

有机质对细颗粒泥沙静水絮凝沉降特性的影响

在CaCl2 和MgCl2 浓度为 0～ 1.0mmol L ,泥沙浓度为 10g L时 ,本文用吸管法研究了有机质对细颗粒泥沙絮凝沉降的影响 ,结果表明 :在液面下同一深度 ,有机质并不影响泥沙浓度随时间呈指数衰减的变化规律。但去除有机质后 ,细颗粒泥沙絮凝的最佳电解质浓度降低 ;对于相同的电解质浓度 ,其絮凝沉降加快 ,泥沙平均沉速明显增大

Polymer Crystallization Influenced by Initial Orientation of Cylindrical Diblock Copolymers in Thin Films

The effect of the initial states (disordered perpendicular cylinder structure vs. parallel cylinder structure) on the crystallization of polystyrene-block-poly(ethylene oxide) (PS-b-PEO) thin films during cyclohexane annealing was investigated. The cylindrical domains perpendicular or parallel to the surface were obtained by controlling the film thickness. During solvent annealing, for the film with the perpendicular cylinders, the ordering degree of cylinders was increased.

Chiral metallo-supramolecular complexes selectively recognize human telomeric G-quadruplex DNA

Here, we report the first example that one enantiomer of a supramolecular cylinder can selectively stabilize human telomeric G-quadruplex DNA. The P-enantiomer of this cylinder has a strong preference for G-quadruplex over duplex DNA and, in the presence of sodium, can convert G-quadruplexes from an antiparallel to a hybrid structure. The compound's chiral selectivity and its ability to discriminate quadruplex DNA have been studied by DNA melting, circular dichroism, gel electrophoresis, fluorescence spectroscopy and S1 nuclease cleavage.

Order-Order Transition of C -> sdG -> sL -> S in ABC Triblock Copolymer Thin Film Induced by Solvent Vapor

The morphology transition of polystyrene-block-poly(butadiene)-block-poly(2-vinylpyridine) (SBV) triblock thin film induced in benzene vapor showing weak selectivity for PS is investigated. The order-order transitions (OOT) in the sequence of core-shell cylinders (C), sphere in 'diblock gyroid' (sdG), sphere in lamella (sL) and sphere (S) are observed. The projection along (111) direction in Gyroid phase (sdG(111)) is found to epitaxially grow from C(001) in the film.

Effect of Shear Flow on the Formation of Ring-Shaped ABA Amphiphilic Triblock Copolymer Micelles

We have investigated the effect of Shear flow on the formation of rill.-shaped ABA triblock copolymer (P4VP(43)-b-PS260-b-P4VP(43)) micelles. The results reveal that Shear flow Plays an important role in the formation of the rings Both ring size and its, distribution are found to be dependent sensitively on the stirring rate. Sizable rings are more likely to be formed at moderate stirring rate, Interestingly, the ring formation mechanism is also dependent oil the Shear flow. Copolymers are likely to form rings via end-to-end cylinder connection at low stirring rates, whereas they tend to form rings via the pathway of the rod-sphere-vesicle-ring it high stirring rates.

Formation of Two Kinds of Hexagonally Arranged Structures in ABC Triblock Copolymer Thin Films Induced by a Strongly Selective Solvent Vapor

An order-order transition (OOT) in the sequence of a hexagonally arranged core-shell cylinder to a double-hexagonally arranged dot in polystyrene-block-poly(butadiene)-block-poly(2-vinylpyridine) (SBV) triblock copolymer thin films is reported to be induced upon exposure to a solvent vapor that: is strongly selective for the two end blocks. These two kinds of hexagonally arranged structures could form when the film thickness is 44, 3.23, and 223 nm. When the film thickness is decreased to 13 nm, the ordered structure is absent. The sizes of the cylinder structures formed with the same annealing time in films of different thickness are compared to address the effects of film thickness on the phase structure. The mechanism is analyzed from the total surface area of the blocks and the effective interaction parameter in the solvent vapor.

Self-assembly of diblock copolymer mixtures in confined states: A Monte Carlo study

The self-assembly of diblock copolymer mixtures (A-b-B/A-b-C or A-b-B/B-b-C mixtures) subjected to cylindrical confinement (two-dimensional confinement) was investigated using a Monte Carlo method. In this study, the boundary surfaces were configured to attract blocks A but repel blocks B and C. Relative to the structures of the individual components, the self-assembled structures of mixtures of the diblock copolymers were more complex and interesting. Under cylindrical confinement, with varying cylinder diameters and interaction energies between the boundary surfaces and the blocks, we observed a variety of interesting morphologies. Upon decreasing the cylinder's diameter, the self-assembled structures of the A(15)B(15)/A(15)C(15) mixtures changed from double-helix/cylinder structures (blocks B and C formed double helices, whereas blocks A formed the outer barrel and inner core) to stacked disk/cylinder structures (blocks B and C formed the stacked disk core, blocks A formed the outer cylindrical barrel), whereas the self-assembled structures of the A(15)B(7)/B7C15 mixtures changed from concentric cylindrical barrel structures to screw/cylinder structures (blocks C formed an inside core winding with helical stripes, whereas blocks A and B formed the outer cylindrical barrels) and then finally to the stacked disk/cylinder structures.