stochastic process algebra based software process simulation modeling

Chinese Acad Sci, ISCAS Lab Internet Software Technologies

Modeling of organic light-emitting diodes with graded concentration in the emissive multilayer

We model the electrical behavior of organic light-emitting diodes whose emissive multilayer is formed by blends of an electron transporting material, tris-(8-hydroxyquinoline) aluminum (Alq(3)) and a hole transporting material, N,N-'-diphenyl-N,N-'-bis(1,1(')-biphenyl)-4,4-diamine. The multilayer is composed of layers of different concentration. The Alq(3) concentration gradually decreases from the cathode to the anode. We demonstrate that these graded devices have higher efficiency and operate at lower applied voltages than devices whose emissive layer is made of nominally homogeneous blends. Our results show an important advantage of graded devices, namely, the low values of the recombination rate distribution near the cathode and the anode, so that electrode quenching is expected to be significantly suppressed in these devices.

Cure processing modeling and cure cycle simulation of epoxy-terminated poly(phenylene ether ketone). V: Estimation of temperature distribution during cure process

A numerical method to estimate temperature distribution during the cure of epoxy-terminated poly(phenylene ether ketone) (E-PEK)-based composite is suggested. The effect of the temperature distribution on the selection of cure cycle is evaluated using a suggested alternation criterion. The effect of varying heating rate and thickness on the temperature distribution, viscosity distribution and distribution of the extent of cure reaction are discussed based on the combination of the here-established temperature distribution model and the previously established curing kinetics model and chemorheological model. It is found that, for a thin composite (<=10mm) and low heating rate (<=2.5K/min), the effect of temperature distribution on cure cycle and on the processing window for pressure application can be neglected. Low heating rate is of benefit to reduce the temperature gradient. The processing window for pressure application becomes narrower with increasing thicknesses of composite sheets. The validity of the temperature distribution model and the modified processing window is evaluated through the characterization of mechanical and physical properties of E-PEK-based composite fabricated according to different temperature distribution conditions.

Cure processing modeling and cure cycle simulation of epoxy-terminated poly(phenylene ether ketone) .3. Determination of the time of pressure application

The curing temperature, pressure, and curing time have significant influence on finished thermosetting composite products. The time of pressure application is one of the most important processing parameters in the manufacture of a thermosetting composite. The determination of the time of pressure application relies on analysis of the viscosity variation of the polymer, associated with curing temperature and curing time. To determine it, the influence of the time of pressure application on the physical properties of epoxy-terminated poly(phenylene ether ketone) (E-PEK)-based continuous carbon fiber composite was studied. It was found that a stepwise temperature cure cycle is more suitable for manufacture of this composite. There are two viscosity valleys, in the case of the E-PEK system, associated with temperature during a stepwise cure cycle. The analysis on the effects of reinforcement fraction and defect content on the composite sheet quality indicates that the width-adjustable second viscosity valley provides a suitable pressing window. The viscosity, ranging from 400 to 1200 Pa . s at the second viscosity valley, is the optimal viscosity range for applying pressure to ensure appropriate resin flow during curing process, which enables one to get a finished composite with optimal fiber volume fraction and low void content. (C) 1997 John Wiley & Sons, Inc.

Cure processing modeling and cure cycle simulation of epoxy-terminated poly(phenylene ether ketone) .4. Cure cycle simulation

Epoxy-terminated poly(phenylene ether ketone) (E-PEK) developed in this Institute is a candidate matrix resin for polymer composites as structural materials. Cure cycles for this reaction system were simulated according to the previously established processing model. It is found that for the E-PEK system, the curing process is best completed by a stepwise cure cycle comprising two isothermal processes at different temperatures, T-1 and T-2. The cure cycles over a wide range of processing parameters simulated, based on the established processing model, indicate that the processing window is width-adjustable. Analysis of the mechanical properties of the composite sheets showed that the simulated cure cycles are acceptable and reliable. (C) 1997 John Wiley & Sons, Inc.

Cure processing modeling and cure cycle simulation of epoxy-terminated poly(phenylene ether ketone) .1. DSC characterization of curing reaction

The curing reaction process of epoxy-terminated poly(phenylene ether ketone) (E-PEK) with 4,4'-diaminodiphenyl sulfone (DDS) and hexahydrophthalic acid anhydride (Nadic) as curing agents was investigated using isothermal differential scanning calorimetry (IDSC) and nonisothermal differential scanning calorimetry (DDSC) techniques. It was found that the curing reactions of E-PEK/DDS and E-PEK/Nadic are nth-order reactions but not autoaccelerating. The experimental results revealed that the curing reaction kinetics parameters measured from IDSC and DDSC are not equivalent. This means that, in the curing reaction kinetics model for our E-PEK system, both isothermal and nonisothermal reaction kinetics parameters are needed to describe isothermal and nonisothermal curing processes, The isothermal and nonisothermal curing processes were successfully simulated using this model. A new extrapolation method was suggested. On the basis of this method the maximum extent of the curing reaction (A(ult)) that is able to reach a certain temperature can be predicted. The A(ult) for the E-PEK system estimated by the new method agrees well with the results obtained from another procedure reported in the literature. (C) 1997 John Wiley & Sons, Inc.

Cure processing modeling and cure cycle simulation of epoxy-terminated poly(phenylene ether ketone) .2. Chemorheological modeling

Chemorheology and corresponding models for an epoxy-terminated poly(phenylene ether ketone) (E-PEK) and 4,4'-diaminodiphenyl sulfone (DDS) system were investigated using a differential scanning calorimeter (DSC) and a cone-and-plate rheometer. For this system, the reported four-parameter chemorheological model and modified WLF chemorheological model can only be used in an isothermal or nonisothermal process, respectively. In order to predict the resin viscosity variation during a stepwise temperature cure cycle actually used, a new model based on the combination of the four-parameter model and the modified WLF model was developed. The combined model can predict the resin viscosity variation during a stepwise temperature cure cycle more accurately than the above two models. In order to simplify the establishment of this model, a new five-parameter chemorheological model was then developed. The parameters in this five-parameter model can be determined through very few rheology and DSC experiments. This model is practicable to describe the resin viscosity variation for isothermal, nonisothermal, or stepwise temperature cure cycles accurately. The five-parameter chemorheological model has also successfully been used in the E-PEK systems with two other curing agents, i.e., the diamine curing agent with the addition of a boron trifluride monoethylamine (BF3-MEA) accelerator and an anhydride curing agent (hexahydrophthalic acid anhydride). (C) 1997 John Wiley & Sons, Inc.

Monitoring and simulation of water, heat,and CO2 fluxes in terrestrial ecosystems based on the APEIS-FLUX system

The Integrated Environmental Monitoring (IEM) project, part of the Asia-Pacific Environmental Innovation Strategy (APEIS) project, developed an integrated environmental monitoring system that can be used to detect, monitor, and assess environmental disasters, degradation, and their impacts in the Asia-Pacific region. The system primarily employs data from the moderate resolution imaging spectrometer (MODIS) sensor on the Earth Observation System- (EOS-) Terra/Aqua satellite,as well as those from ground observations at five sites in different ecological systems in China. From the preliminary data analysis on both annual and daily variations of water, heat and CO2 fluxes, we can confirm that this system basically has been working well. The results show that both latent flux and CO2 flux are much greater in the crop field than those in the grassland and the saline desert, whereas the sensible heat flux shows the opposite trend. Different data products from MODIS have very different correspondence, e.g. MODIS-derived land surface temperature has a close correlation with measured ones, but LAI and NPP are quite different from ground measurements, which suggests that the algorithms used to process MODIS data need to be revised by using the local dataset. We are now using the APEIS-FLUX data to develop an integrated model, which can simulate the regional water,heat, and carbon fluxes. Finally, we are expected to use this model to develop more precise high-order MODIS products in Asia-Pacific region.

Modeling gross primary production of alpine ecosystems in the Tibetan Plateau using MODIS images and climate data

The eddy covariance technique provides measurements of net ecosystem exchange (NEE) Of CO2 between the atmosphere and terrestrial ecosystems, which is widely used to estimate ecosystem respiration and gross primary production (GPP) at a number Of CO2 eddy flux tower sites. In this paper, canopy-level maximum light use efficiency, a key parameter in the satellite-based Vegetation Photosynthesis Model (VPM), was estimated by using the observed CO2 flux data and photosynthetically active radiation (PAR) data from eddy flux tower sites in an alpine swamp ecosystem, an alpine shrub ecosystem and an alpine meadow ecosystem in Qinghai-Tibetan Plateau, China. The VPM model uses two improved vegetation indices (Enhanced Vegetation Index (EVI), Land Surface Water Index (LSWI)) derived from the Moderate Resolution Imaging Spectral radiometer (MODIS) data and climate data at the flux tower sites, and estimated the seasonal dynamics of GPP of the three alpine grassland ecosystems in Qinghai-Tibetan Plateau. The seasonal dynamics of GPP predicted by the VPM model agreed well with estimated GPP from eddy flux towers. These results demonstrated the potential of the satellite-driven VPM model for scaling-up GPP of alpine grassland ecosystems, a key component for the study of the carbon cycle at regional and global scales. (c) 2006 Elsevier Inc. All rights reserved.

裂隙/孔隙型弹性介质中地震波场模拟与叠前逆时偏移

With the development of oil/gas seismic exploration, seismic survey for fracture/porosity type reservoir is becoming more and more important. As for China, since it has over 60% store of low porosity and low permeability oil/gas reservoir, it’s more urgent to validly describe fracture/porosity type oil/gas trap and proposing the related, developed seismic technique. To achieve mapping fracture/porosity region and its development status, it demands profound understanding of seismic wave propagation discipline in complex fractured/pored media. Meanwhile, it has profound scientific significance and applied worth to study forward modeling of fracture/porosity type media and pre-stacked reverse time migration. Especially, pre-stacked reverse-time migration is the lead edge technique in the field of seismology and seismic exploration. In this paper, the author has summarized the meaning, history and the present state of numerical simulation of seismic propagation in fractured/pored media and seismic exploration of fractured/pored reservoirs. Extensive Dilatancy Anisotropy (EDA) model is selected as media object in this work. As to forward modeling, due to local limitation of solving spatial partial derivative when using finite-difference and finite-element method, the author turns to pseudo-spectral method (PSM), which is based on the global characteristic of Fourier transform to simulate three-component elastic wave-field. Artifact boundary effect reduction and simulation algorithm stability are also discussed in the work. The author has completed successfully forward modeling coding of elastic wave-field and numerical simulation of two-dimensional and three-dimensional EDA models with different symmetric axis. Seismic dynamic and kinematical properties of EDA media are analyzed from time slices and seismic records of wave propagation. As to pre-stacked reverse-time migration for elastic wave-field in fractured/pored media, based on the successful experience in forward modeling results with PSM, the author has studied pre-stacked reverse-time depth-domain migration technique using PSM of elastic wave-field in two dimensional EDA media induced by preferred fracture/pore distribution. At the same time, different image conditions will bring up what kind of migration result is detailed in this paper. The author has worded out software for pre-stacked reverse-time depth-domain migration of elastic wave-field in EDA media. After migration processing of a series of seismic shot gathers, influences to migration from different isotropic and anisotropy models are described in the paper. In summary, following creative research achievements are obtained:  Realizing two-dimensional and three-dimensional elastic wave-field modeling for fractured/pored media and related software has been completed.  Proposed pre-stacked reverse-time depth-domain migration technique using PSM of elastic wave-field.  Through analysis of the seismic dynamic and kinematical properties of EDA media, the author made a conclusion that collection of multi-component seismic data can provide important data basis for locating and describing the fracture/pore regions and their magnitudes and the preferred directions.  Pre-stacked reverse-time depth-domain migration technique has the ability to reconstruct complex geological object with steep formations and tilt fracture distribution. Neglecting seismic anisotropy induced by the preferred fracture/pore distribution, will lead to the disastrous imaging results.

裂缝性油气藏储层预测方法研究

In this paper, based on the E & P situation in the oilfield and the theory of geophysical exploration, a series researches are conducted on fracture reservoir prediction technology in general，and it especially focus on some difficult points. The technological series which integrated amplitude preserved data processing、interpretation and its comprehensive application research as a whole were developed and this new method can be applied to the other similar oilfield exploration and development. The contents and results in this paper are listed as follows: 1. An overview was given on the status and development of fracture reservoir estimation technique, compare and analyze those geophysical prediction methods. This will be very helpful to the similar reservoir researches. 2. Analyze and conclude the characters of geologies and well logging response of burial hills fracture reservoir, those conclusions are used to steer the geophysical research and get satisfying results. 3. Forward modeling anisotropy seismic response of fracture reservoir. Quantitatively describe the azimuthal amplitude variation. Amplitude ellipse at each incidence angle is used to identify the fracture orientation. 4. Numerical simulation of structure stress based on finite difference method is carried out. Quantitatively describe and analyze the direction and intensity of fracture. 5. Conventional attributes extraction of amplitude preserved seismic data、attributes with different azimuthal angle and different offset are used to determine the relationship between the results and fracture distribution. 6. With spectrum decomposition method based on wavelet transform， the author disclose the reservoir distribution in space. It is a powerful tool to display its anisotropy. 7. Integrated seismic wave impendence、elastic impendence、spectrum decomposition、attribute extraction、fracture analysis result as a whole to identify and evaluate the fracture reservoir. An optimum workflow is constructed. It is used to practical oil&gas production and good results are obtained. This can indicate the wide foreground of this technique series.

基于弹性参数分析的碳酸盐岩储层预测方法研究

Prediction of Carbonate Reservoir Based on the Elastic Parameter Analysis Zhang Guangzhi (Solid Geophysics) Directed by Professor Liu Hong Abstract With the exploration and development of Puguang Oilfield, oil-gas exploration of carbonate rock in China has shown good prospects. Research on earthquake prediction methods for carbonate reservoir becomes the key of oil and gas exploration. Starting with analysis of geological characteristics of carbonate rock, prestack AVO inversion method, prestack elastic impedance inversion and parameter calculation method and seismic attribute extraction and optimization method were studied based on the analysis of rock physics in this work. First, variation characteristic and law of carbonate rock reservoir parameters were studied based on experimental data of rock physics, log data, analysis assay data, mud logging data and seismic data, so as to lay a foundation for the further reservoir identification and description. Then, the structure, type and propagation law of seismic wave field were analyzed through seismic forward modeling of the reservoir, and contact between information from log and geology data with elastic parameters, such as compressional wave and shear wave velocity and density were established, so as to provide a standard for reservoir identification and hydrocarbon detection using seismic reflection characteristics of the research area. Starting with the general concept of inverse problem, through analysis of Zoeppritz equation, three kinds of pre-stack inversion methods were derived and analyzed in detail, the AVO 3-parameter inversion based on Bayesian theory, the prestack AVO waveform inversion method and the simultaneous inversion method, based on the statistical hypothesis of inversion parameters and observation data and the Gauss distribution assumption of noise. The three methods were validated by model data and real data. Then, the elastic wave impedance inversion method of carbonate reservoir was investigated and the method of elastic parameter extraction from elastic impedance data was put forward. Based on the analysis of conventional methods of seismic attribute extraction and optimization, the time-frequency attributes and the wavelet attributes with time and amplitude feature were presented, and the prestack seismic attribute calculation method which can characterize the reservoir rock and fluid characteristic was presented. And the optimization of seismic attribute using the nonlinear KPCA method was also put forward. A series of seismic prediction technologies for carbonate reservoir were presented based on analysis of rock physics and seismic forward simulation technology. Practical application of these technologies was implemented in A oil field of Southern China and good effect has been achieved. Key words: carbonate rock; reservoir prediction; rock physics, prestack seismic inversion; seismic attribute

二氧化碳在孔隙咸水层中多相流动数值模拟研究

There has been a growing concern about the use of fossil fuels and its adverse effects on the atmospheric greenhouse and ecological environment. A reduction in the release rate of CO2 into the atmosphere poses a major challenge to the land ecology of China. The most promising way of achieving CO2 reduction is to dispose of CO2 in deep saline aquifers. Deep aquifers have a large potential for CO2 sequestration in geological medium in terms of volume and duration. Through the numerical simulation of multiphase flow in a porous media, the transformation and motion of CO2 in saline aquifers has been implemented under various temperature and hydrostatic pressure conditions, which plays an important role to the assessment of the reliability and safety of CO2 geological storage. As expected, the calculated results can provide meaningful and scientific information for management purposes. The key problem to the numerical simulation of multiphase flow in a porous media is to accurately capture the mass interface and to deal with the geological heterogeneity. In this study, the updated CE/SE (Space and time conservation element and solution element) method has been proposed, and the Hybrid Particle Level Set method (HPLS) has extended for multiphase flows in porous medium, which can accurately trace the transformation of the mass interface. The benchmark problems have been applied to evaluate and validate the proposed method. In this study, the reliability of CO2 storage in saline aquifers in Daqingzi oil field in Sunlong basin has been discussed. The simulation code developed in this study takes into account the state for CO2 covering the triple point temperature and pressure to the supercritical region. The geological heterogeneity has been implemented, using the well known geostatistical model (GSLIB) on the base of the hard data. The 2D and 3D model have been set up to simulate the CO2 multiphase flow in the porous saline aquifer, applying the CE/SE method and the HPLS method .The main contents and results are summarized as followings. (1) The 2D CE/SE method with first and second –order accuracy has been extended to simulate the multiphase flow in porous medium, which takes into account the contribution of source and sink in the momentum equation. The 3D CE/SE method with the first accuracy has been deduced. The accuracy and efficiency of the proposed CE/SE method have been investigated, using the benchmark problems. (2) The hybrid particle level set method has been made appropriate and extended for capturing the mass interface of multiphase flows in porous media, and the numerical method for level set function calculated has been formulated. (3) The closed equations for multiphase flow in porous medium has been developed, adept to both the Darcy flow and non-Darcy flow, getting over the limitation of Reynolds number to the calculation. It is found that Darcy number has a decisive influence on pressure as well as velocity given the Darcy number. (4) The new Euler scheme for numerical simulations of multiphase flows in porous medium has been proposed, which is efficient and can accurately capture the mass interface. The artificial compressibility method has been used to couple the velocities and pressure. It is found that the Darcy number has determinant effects on the numerical convergence and stability. In terms of the different Darcy numbers, the coefficient of artificial compressibility and the time step have been obtained. (5) The time scale of the critical instability for critical CO2 in the saline aquifer has been found, which is comparable with that of completely CO2 dissolved saline aquifer. (6) The concept model for CO2 multiphase flows in the saline aquifer has been configured, based on the temperature, pressure, porosity as well as permeability of the field site .Numerical simulation of CO2 hydrodynamic trapping in saline aquifers has been performed, applying the proposed CE/SE method. The state for CO2 has been employed to take into account realistic reservoir conditions for CO2 geological sequestration. The geological heterogeneity has been sufficiently treated , using the geostatistical model. (7) It is found that the Rayleigh-Taylor instability phenomenon, which is associated with the penetration of saline fluid into CO2 fluid in the direction of gravity, has been observed in CO2 multiphase flows in the saline aquifer. Development of a mushroom-type spike is a strong indication of the formation of Kelvin-Helmholtz instability due to the developed short wavelength perturbations present along the interface and parallel to the bulk flow. Additional key findings: the geological heterogeneity can distort the flow convection. The ascending of CO2 can induce the persistent flow cycling effects. The results show that boundary conditions of the field site have determinant effects on the transformation and motion of CO2 in saline aquifers. It is confirmed that the proposed method and numerical model has the reliability to simulate the process of the hydrodynamic trapping, which is the controlling mechanism for the initial period of CO2 storage at time scale of 100 years.

三角洲储层孔隙结构模型与剩余油分布研究——以临南油田沙河街组储层为例

The study of pore structure in reservoir was paid attention to in the early reservoir research and now a systematic research methodology is set up. On the limits of tools and conditions, methodologies and technologies on formation condition and distribution laws of pore structure and the relationship between remaining oil distribution and pore structure are uncertain and some knownage about it is also uncertain. As the development of petroleum industry, the characterization of pore structure and the prediction of remaining oil are the hot spot and difficult point in the research of oil development. The author pays a close attention to this subject and has done much research on it. In a case study in Linnan oilfield Huimin sag Jiyang Depression Bohai Bay basin by using a new method, named varied scale comprehensive modeling of pore structure, the author builds pore structure models for delta reservoir, reveals the remaining oil distribution laws in delta facies, and predicts the distribution of remaining oil in Linnan oilfield. By the application of stratigraphy, sedimentology and structure geology. the author reveals the genetic types of sandbody and its distribution laws, builds the reservoir geological models for delta sandstone reservoir in Shahejie group in Linnan oilfield and points out the geological Factors that control the development of pores and throats. Combining petrology and the reservoir sensitive analysis, the author builds the rock matrix models. It is the first time to state that rocks in different sentimental micro facies have different sensitive .response to fluid pressed into the rocks. Normally. the reservoirs in the delta front have weaker sensitivity to fluid than the reservoirs in delta plain, In same subfacies, the microfacies that have fine grain, such as bank and crevasse splay, have stronger reservoir sensitivity than the microfacies that have coarse grains, such as under-water branched channel and debauch bar. By the application of advanced testing, such as imagine analysis, scan electronic microscope, and morphology method, the author classifies the pore structure and set up the distribution models of pore, throat and pore structure. By the application of advanced theory in well-logging geology, the author finds the relationship between microscope pore structure and macroscopic percolation characteristics, and then builds the well-logging interpretation formulae for calculating pore structure parameters. By using the geostatistics methods, the author reveals the spatial correlative characteristics of pore structure. By application of conditional stochastic simulation methods, the author builds the 3D models of pore structure in delta reservoir. It is the base of predicting remaining oil distribution. By a great deal of experiments and theoretical deduction, The author expounds the laws of percolation flow in different pore structures, and the laws by which the pore structure controls the micro distribution of remaining oil, and then, states the micro mechanism of remaining oil distribution. There are two types of remaining oil. They are by-pass flow caused by micro-fingering and truncation caused by non-piston movement. By new method, the author states the different pore structure has different replacement efficiency, reveals the formation condition and distribution laws of remaining oil. predicts the remaining oil distribution in Linnan oil field, and put forward some idea about how to adjust the oil production. The study yielded good results in the production in Linnan oilfield.

改造型盆地油气成藏机理与油气预测－以银根－额济纳旗盆地为例

Reformed basin is a basin that underwent multiple immense reformation after the sedimentary stage, the major geologic elements of the petroleum system in the prototyped basin are destroyed to a certain extent, and their petroleum system has been reconstructed. This type of basin is frequently found in the course of exploration both home and abroad. In China, especially in the western and southern part of China, the basins in which oil explorations have been conducted are mostly reformed basins. The reformed basins from Paleozoic, Late Mesozoic to Cenozoic are widely distributed in West and South China. They are, and moreover, will be a challenge for oil and gas exploration. The conventional investigation and exploration techniques used in the slightly reconstructed basin just don't work well when facing the reformed basin. Therefore, the study on the reformed basin, especially the study on the pool-forming mechanism and reservoir prediction becomes a focus and one of difficulties for the geologists overseas and domestic. Yingen-Ejinaqi Basin is a typical case of the Late Mesozoic and Cenozoic reformed basins in China. It locates in West China and is a exploration frontier with difficulties and no break through is made for years. A comprehensive research on it will be of significance for oil and gas exploration in similar basins of China. The late research for reformed basin in China now is mainly concentrated on basin classification, formation mechanism, geologic features, and survey technique, distribution regularity of oil accumulation and its dominating factors, assessment of oil exploration prospect and target zones, etc. On the other hand, the study on the pool-forming mechanism and reservoir prediction seems insufficient in systematization, and the research is deficient in methodology and combination of qualitative and quantitative studies, as well as the application of the new theory and techniques. The current efforts are mainly directed to structures (faults), sedimentation, the relationship between reservoir evolution and oil accumulation, and some other relevant fields. However, the application of the new theory and techniques seems to be insufficient such as petroleum system, pool-forming dynamics, fluid pressure compartment, and basin simulation, etc. So is the dynamic and integrated research. As a result, incomplete knowledge and understandings derived from the research on pool-forming mechanism and reservoir prediction often do not accord with rea-lity of the basin. The study and exploration under the guidance of this knowledge will inevitably lead to errors and failure. This paper, based on the previous study of the other geologists on reformed basins, with emphasis on "wholeness or systematic, dynamic and integrated" research, presents a reverse thinking of beginning from conserved units in the basin and the combination of qualitative and quantitative study with new theory and technique by building a geological model. The paper also puts forward a new thought for studying the oil & gas accumulation and reservoir prediction , and establishes a new research system for reformed basin. It is verified by the known reservoir and oil accumulation area in the basin and has a practical value for use and reference. The new ideas and achievements in this research are as following: 1.This is the first time that the system for studying the reformed basin and its pool-forming mechanism and reservoir prediction is presented. A reverse thinking and combination of qualitative & quantitative are applied here with emphasis on "wholeness or systematic, dynamic and integrated" research, new theory, techniques & methods comprehensive use and geologic models building. 2. Identifying criterion and methods, classifying schemes, and denominating principles for the conserved units of reformed basins are presented in this paper. The geologic model of conserved units of Yingen-Ejinaqi Basin has been built. It is a practical method when combined with the traditional way for basin survey and the conserved units study. 3.The dynamic sources of basin deformation are believed to be stress, gravity and thermodynamics. The stress and gravity are key factors in basin deformation and pool forming, especially stress. Scientific proof is provided by classifying the functional type, style and range of the stress, gravity and thermodynamics. 4.The pool forming and reservoir distribution of Yingen-Ejinaqi Basin are controlled by multiple factors or geologic conditions or/and co-controlled by both of them. The qualitative and quantitative research on petroleum system and basin modeling will help us understand and determine the pool-forming period of the conserved unit (timing), the oil migrating direction (orientation), the oil accumulating region (location), the oil distributing border (bordering) and the size of oil accumulation (quantification). Thus the pool-forming and distribution zones can be predicted. 5.Three generating modes (reform-succession type, reform-destroyed type and reform-regenerating type or reform-newborn type) of pool forming for reformed basins are presented here, together with the inner relationships between basin deformation type, overlapping style and pool-forming modes. The pool-forming modes are determined by deformation type and overlapping style. Reservoir distribution will be predicted based on the modes and other concrete pool-forming conditions. 6.The evaluation methods of the conserved units and zones and the parameter selection are reliable in optimal selecting of target zones. The technical terms, new ideas and methods for the study of reformed basins, the pool-forming mechanism and reservoir prediction are presented in this paper. The concepts and terms, the identifying criterion, the denominating principles, the generating modes for pool forming, the methods of reservoir prediction, and the evaluation techniques for conserved units and zones can be used for reference in studies on the petroleum exploration of reformed basins in China and abroad. It serves as a typical example for further research of the reformed basins and the geologic regulations of oil accumulation. It has a practical value of use and reference. The future research in the field of pool-forming mechanism of the reformed basins may well be on the process simulation of pool-forming dynamics of the reformed basins. Experimental work has been conducted to simulate the processes by using quantitative and qualitative methods combined. The further study in this field calls for more efforts.