ScAlMgO_4晶体的生长缺陷

采用提拉法生长出φ30 mm×55 mm的ScAlMgO4晶体。在晶体生长过程中有轻微的挥发,粉末X射线衍射分析表明:挥发物质为MgO单相。运用扫描电镜、光学显微镜以及高分辨X射线衍射仪对晶体中的包裹物、开裂、生长条纹和小角晶界缺陷进行了研究。结果表明:温度梯度和热应力是形成晶体中缺陷的主要原因。通过合理设计温场,控制固-液界面的形状及冷却过程的降温速率,可以提高晶体的完整性。

导模法和温度梯度法生长r面蓝宝石(英文)

r面(0112)蓝宝石晶体可用作制备非极性GaN薄膜的衬底。采用温度梯度法(temperature gradient technique,TGT)和导模法(edge-defined film-fed crystal growth,EFG)生长了质量良好的r面蓝宝石晶体。利用双晶衍射、光学显微镜、光谱仪观察和分析了晶体的结构和缺陷。结果表明:TGT法生长的r蓝宝石晶体的双晶摇摆曲线对称性好,半高宽值仅为18 rad.s,位错密度为4×103 cm-2,透过率达83%,晶体质量好。与TGT法相比,EFG法生长的r面蓝宝石晶体的结构完整性较差,位错密度为5×105 cm-2,透过率仅为75%。但是EFG法具有晶体生长速度快,后期加工成本低的优点。

Influence of carbon on the thermoluminescence and optically stimulated luminescence of α -Al2O3:C crystals

alpha-Al2O3:C crystal shows excellent thermoluminescence (TL) and optically stimulated luminescence (OSL) properties but the real role carbon plays in this crystal is still not clearly understood so far. In this work, alpha-Al2O3:C crystal doping with different amounts of carbon were grown by the temperature gradient technique, and TL and OSL properties of as-grown crystals were investigated. Additionally, a mechanism was proposed to explain the role of carbon in forming the TL and OSL properties of alpha-Al2O3:C. TL and OSL intensities of as-grown crystals increase with the increasing amount of carbon doping in the crystal, but no shift is found in the glow peak location at 465 K. As the amount of carbon doping in the crystals decreases, OSL decay rate becomes faster. With the increase in heating rate, the integral TL response of as-grown crystals decreases and glow peak shifts to higher temperatures. TL response decrease rate increases with the increasing amount of carbon doping in the crystals. All the TL and OSL response curves of as-grown crystals show linear-sublinear-saturation characteristic, and OSL dose response exhibits higher sensitivity and wider linear dose range than that of TL. The crystal doping with 5000 ppm carbon shows the best dosimetric properties. Carbon plays the role of a dopant in alpha-Al2O3:C crystal and four-valent carbon anions replace the two-valent anions of oxygen during the crystal growth process, and large amounts of oxygen vacancies were formed, which corresponds to the high absorption coefficient of F and F+ centers in the crystals.

α-Al_2O_3:C晶体的热释光和光释光特性

以高纯α-Al2O3和石墨为原料,采用温梯法生长了α-Al2O3:C晶体,使用RisΦTL/OSL-DA-15型热释光和光释光仪研究了其热释光和光释光特性.α-Al2O3:C晶体在462K附近有单一热释光峰,发射波长位于410nm.随着辐照剂量的增加,热释光强度逐渐增强,462K的热释光特征峰位置保持不变.α-Al2O3:C晶体的光释光衰减曲线由快衰减和慢衰减两个部分组成,随着辐照剂量的增加,快衰减部分衰减速率变化不大,而慢衰减部分衰减速率加快.在5×10-6—10Gy剂量范围内,α-Al2O3:C晶体的热释光剂量响应呈现良好的线性关系,30Gy时达到饱和;光释光剂量响应在5×10-6—60Gy剂量范围内呈现良好的线性关系,100Gy时达到饱和.与热释光相比,光释光剂量响应具有更高的灵敏度和更宽的线性剂量响应范围.

Growth of alpha-Al2O3:C crystal with highly sensitive optically stimulated luminescence

In this work. an alpha-Al2O3:C crystal was directly grown by the temperature gradient technique (TGT) using Al2O3 and graphite powders as the raw materials. The optical, optically stimulated luminescence (OSL) properties and dosimetric characteristics of as-grown crystal were investigated. As-grown alpha-Al2O3:C crystal shows strong absorption band at 205, 230 and 256 nm. Three-dimensional thermoluminescence (TL) emission spectrum of the crystal shows a single emission peak at similar to 415 nm. The OSL decay curve can be fitted to two exponentials, the faster component and the slower component. The OSL response of the crystal shows a linear-sublinear-saturation characteristic. As-grown alpha-Al2O3:C crystal shows excellent linearity in the dose range from 5 x 10(-6) to 50 Gy. For doses higher than the saturation dose (100 Gy). the OSL sensitivity decreases as the dose increases. Crown Copyright (C) 2008 Published by Elsevier B.V. All rights reserved.

Study of Al2O3/MgF2 HR coatings at 355 nm

With the present work we tried to study the effective methods to improve the laser-induced damage threshold (LIDT) and reflectance of HR coatings at 355 nm. The work presented in this paper wits part of an ongoing study about vacuum annealing. It was dedicated to study the effects Of Vacuum annealing with different temperature gradients on the structure, optical properties and laser-induced damage threshold (LIDT) of 355nm Al2O3/MgF2HR coatings. A number of samples were prepared by electron beam evaporation using the same deposition process with an optimal deposition temperature of 280 degrees C. After deposition, samples were annealed in the coating chamber for 3 h with different temperature gradients. Morphologies of the samples were observed by Leica-DMRXE. Microscope, Structure of the samples had been characterized by X-ray diffraction (XRD). Transmittance and reflectance of the samples were measured by Lambda 900 Spectrometer, The LIDT of the samples was measured by a 355 nm Nd:YAG laser with a pulse width of 8 ns. It was found that the temperature gradient of vacuum annealing had significant effects on the morphology, structure, absorption, and LIDT of the samples, (c) 2005 Elsevier Ltd. All rights reserved.

Thermodynamic damage mechanism of transparent films caused by a low-power laser

A new model for analyzing the laser-induced damage process is provided. In many damage pits, the melted residue can been found. This is evidence of the phase change of materials. Therefore the phase change of materials is incorporated into the mechanical damage mechanism of films. Three sequential stages are discussed: no phase change, liquid phase change, and gas phase change. To study the damage mechanism and process, two kinds of stress have been considered: thermal stress and deformation stress. The former is caused by the temperature gradient and the latter is caused by high-pressure drive deformation. The theory described can determine the size of the damage pit. (c) 2006 Optical Society of America.

黑龙江嘉荫地区古新世孢粉植物群及古植被、古气候研究

植物是环境变化的重要指示物之一。晚白垩至早第三纪时期，全球生态系统发生了剧烈变化，研究这一时期植物对了解地质历史时期环境变化趋势, 认识和保护当今环境有重要意义。我国黑龙江省嘉荫县有这一时期的地层发育，其中乌云煤矿和白山头是主要的露头剖面。前人曾从地质时代、孢粉及植物化石角度对这两个剖面进行过研究，但是仍有部分问题尚存争议。在本项工作中，我们对两个剖面的孢粉样品进行了系统采样，部分孢粉类型同时在光镜和电镜下进行了拍照。我们还对存在争议的这两个剖面的地质时代进行了讨论。同时，首次用共存分析法对这两个剖面的在沉积时期的气候进行了整体及分段的定量重建。另外，我们结合中其它地点的气候重建工作对不同时期的纬度温度梯度进行了研究。 乌云煤矿和白山头两个乌云组剖面的古新世孢粉植物群的研究结果表明：乌云煤矿孢粉植物群主要是与榛属（Corylus），桤木属（Alnus），桦木属（Betula），榆属（Ulmus）及松属（Pinus）有亲缘关系的植物；白山头剖面的孢粉植物类型与乌云煤矿基本一致，但是其中针叶类植物的花粉所占比重较大。 根据乌云煤矿与白山头剖面的孢粉类型在地层中的分布，以及与其它古新世地层的对比，我们认为乌云煤矿与白山头含孢粉段的地质时代为古新世。 用共存分析法得到乌云组古新世气候参数有两组。孢粉类型的共存结果为：年均温14.8-14.9℃，年降水量816-1389mm；植物化石类型的共存结果为：年均温16.3-16.8℃, 年降水：1124-1623mm。对乌云煤矿与白山头两个剖面孢粉带中的孢粉类型的气候参数分别进行共存，结果表明，除乌云煤矿孢粉第三带到第四带外，乌云地区的年均温在整个沉积时期均呈上升趋势；年均降水量的变化趋势与年均温基本一致。 根据从古新世到现代不同地点气候定量重建的年均温参数，我们计算得到了不同时期纬度温度梯度变化的值：<0.1℃/古纬度（古新世）、 0.1℃/古纬度（始新世）、0.45℃/纬度（中新世）、0.55℃/纬度（上新世）。结合当今全球的平均温度梯度值（0.7℃/纬度），我们得出纬度温度梯度的值从古新世以来呈不断上升的趋势。这一结果显示65Ma 以来赤道与极地间的温度差异逐渐增大，同时也提示了全球温度可能呈下降趋势。

Operational Optimization of GaN Thin Film Growth Employing Numerical Simulation in a Showerhead MOCVD Reactor

A detailed reaction-tran sport model was studied in a showerhead reactor for metal organic chemical vapor deposition of GaN film by using computational fluid dynamics simulation. It was found that flat flow lines without swirl are crucial to improve the uniformity of the film growth, and thin temperature gradient above the suscptor can increase the film deposition rate. By above-mentioned research, we can employ higher h (the distance from the susceptor to the inlet), P (operational pressure) and the rate of susceptor rotation to improve the film growth.

Thermal induced facet destructive feature of quantum cascade lasers

We present a study on the facet damage profile of quantum cascade lasers (QCLs). Conspicuous cascade half-loop damage strips on front facet are observed when QCLs catastrophically failed. Due to the large difference on thermal conductivities between active region and the substrate, dominant heat is compulsively driven to the substrate. Abundant heat accumulation and dissipation on substrate build large temperature gradient and thermal lattice mismatch. Thermal-induced stress due to sequential mismatch leads to the occurrence of the multistep damages on front facet. Good agreement is achieved between the observed locations of damaged strips and the calculated results.

INVESTIGATION OF C-60 SINGLE-CRYSTAL BY X-RAY-METHODS

C-60 Single crystals grown by a single-temperature-gradient technique were characterized by synchrotron radiation white beam x-ray topography and x-ray double crystal diffraction with Cu K-alpha 1 radiation on conventional x-ray source. The results show that the crystal is rather well crystallized, The x-ray topographies give an evidence of dendritic growth mechanism of C-60 Single crystal, and x-ray double crystal diffraction rocking curve shows that there are mosaic structural defects in the sample. A phase transition st 249+/-1.5% K from a simple cubic to a face centered cubic structure is confirmed by in situ observation of synchrotron radiation white beam x-ray topography with the temperature varing from 230 to 295 K.

Ignition of single coal particle in a hot furnace under normal- and micro-gravity condition

An experimental study on ignition and combustion of single particles was conducted at normal gravity (1-g) and microgravity (l-g) for three high volatile coals with initial diameter of 1.5 and 2.0 mm, respectively. The non-intrusive twin-color pyrometry method was used to retrieve the surface temperature of the coal particle through processing the images taken by a color CCD camera. At the same time, a mathematical model considering thermal conduction inside the coal particle was developed to simulate the ignition process. Both experiments and modeling found that ignition occurred homogeneously at the beginning and then heterogeneously for the testing coal particles burning at l-g. Experimental results confirmed that ignition temperature decreased with increasing volatile content and increasing particle size. However, contradicted to previous studies, this study found that for a given coal with certain particle size, ignition temperature was about 50–80 K lower at l-g than that at 1-g. The model predictions agreed well with the l-g experimental data on ignition temperature. The criterion that the temperature gradient in the space away from the particle surface equaled to zero was validated to determine the commence of homogeneous ignition. Thermal conduction inside the particle could have a noticeable effect for determining the ignition temperature. With the consideration of thermal conduction, the critical size for the phase transient from homogeneous to heterogeneous is about 700 lm at ambient temperature 1500 K and oxygen concentration 0.23. 2009 The Combustion Institute. Published by Elsevier Inc. All rights reserved.

Thermocapillary Migration of Deformable Bubbles at Moderate to Large Marangoni Number in Microgravity

Using the level-set method and the continuum interface model, the axisymmetric thermocapillary migration of gas bubbles in an immiscible bulk liquid with a temperature gradient at moderate to large Marangoni number is simulated numerically. Constant material properties of the two phases are assumed. Steady state of the motion can always be reached. The terminal migration velocity decreases monotonously with the increase of the Marangoni number due to the wrapping of isotherms around the front surface of the bubble. Good agreements with space experimental data and previous theoretical and numerical studies in the literature are evident. Slight deformation of bubble is observed, but no distinct influence on the motion occurs. It is also found that the influence of the convective transport of heat inside bubbles cannot be neglected at finite Marangoni number, while the influence of the convective transport of momentum inside bubbles may be actually negligible.

Three-Dimensional Linear Instability Analysis of Thermocapillary Return Flow on a Porous Plane

A three-dimensional linear instability analysis of thermocapillary convection in a fluid-porous double layer system, imposed by a horizontal temperature gradient, is performed. The basic motion of fluid is the surface-tension-driven return flow, and the movement of fluid in the porous layer is governed by Darcy's law. The slippery effect of velocity at the fluid-porous interface has been taken into account, and the influence of this velocity slippage on the instability characteristic of the system is emphasized. The new behavior of the thermocapillary convection instability has been found and discussed through the figures of the spectrum.