Resonant two-photon cross-section calculations for transitions to 4f5d state in Pr3+: YAG using density matrix theory

The density matrix resonant two-photon absorption (TPA) theory is applied to a rare-earth ion-doped laser crystal. TPA cross sections for transitions from the ground state to the first 4f5d state in Pr3+:YAG are calculated. The results indicate the density matrix TPA theory is attractive in studying TPA in laser crystals. (C) 2000 Elsevier Science B.V. All rights reserved.

Seismic profiles across the middle Tan-Lu fault zone in Laizhou Bay, Bohai Sea, eastern China

The stratigraphic architecture, structure and Cenozoic tectonic evolution of the Tan-Lu fault zone in Laizhou Bay, eastern China, are analyzed based on interpretations of 31 new 2D seismic lines across Laizhou Bay. Cenozoic strata in the study area are divided into two layers separated by a prominent and widespread unconformity. The upper sedimentary layer is made up of Neogene and Quaternary fluvial and marine sediments, while the lower layer consists of Paleogene lacustrine and fluvial facies. In terms of tectonics, the sediments beneath the unconformity can be divided into four main structural units: the west depression, central uplift, east depression and Ludong uplift. The two branches of the middle Tan-Lu fault zone differ in their geometry and offset: the east branch fault is a steeply dipping S-shaped strike-slip fault that cuts acoustic basement at depths greater than 8 km, whereas the west branch fault is a relatively shallow normal fault. The Tan-Lu fault zone is the key fault in the study area, having controlled its Cenozoic evolution. Based on balanced cross-sections constructed along transverse seismic line 99.8 and longitudinal seismic line 699.0, the Cenozoic evolution of the middle Tan-Lu fault zone is divided into three stages: Paleocene-Eocene transtension, Oligocene-Early Miocene transpression and Middle Miocene to present-day stable subsidence. The reasons for the contrasting tectonic features of the two branch faults and the timing of the change from transtension to transpression are discussed. Crown Copyright (C) 2008 Published by Elsevier Ltd. All rights reserved.

On SAR wind speed ambiguities and related geophysical model functions

Recent investigations show that normalized radar cross sections for C-band microwave sensors decrease under high wind conditions with certain incident angles instead of increase, as is the case for low to moderate wind speeds. This creates the problem of ambiguities in high wind speed retrievals from synthetic aperture radar (SAR). In the present work, four geophysical model functions (GMFs) are studied, namely the high wind C-band model 4 (CMOD4HW), C-band model 5 (CMOD5), the high wind vertical polarized GMF (HWGMF_VV), and the high wind horizontal polarized GMF (HWGMF_HH). Our focus is on model behaviours relative to wind speed ambiguities. We show that, except for CMOD4HW, the other GMFs exhibit the wind speed ambiguity problem. To consider this problem in high wind speed retrievals from SAR, we focus on hurricanes and propose a method to remove the speed ambiguity using the dominant hurricane wind structure.

Embryology of Swertia (Gentianaceae) relative to taxonomy

The embryological features of three species of Swertia (s.l.) - S. erythrosticta, S. franchetiana, and S. tetraptera were characterized, and the observations were used, together with previously gathered data on other species, to evaluate a recently proposed polyphyly, based on molecular data, of Swertia s.l. Comparisons of species within the genus showed that they have diversified embryologically, and there are significant between-species differences. Notable features that vary between species include the number of cell layers that form the anther locule wall, the construction of the wall of the mature anther, tapetum origin, the cell number in mature pollen grains, the structure of the fused margins of the two carpels, the ovule numbers in placental cross-sections, the shape of the mature embryo sac, the degree of ovule curvature, antipodal variation and the presence of a hypostase, and seed appendages. They share characters that are widely distributed in the tribe Gentianeae, such as a dicotyledonous type of anther wall formation, a glandular tapetum with uninucleate cells, simultaneous cytokinesis following the meiosis of the microsporocytes, tetrahedral microspore tetrads, superior, bicarpellary and unilocular ovaries, unitegmic and tenuinucellar ovules, Polygonum-type megagametophytes, progamous fertilization, nuclear endosperm, and Solanad-type embryogeny. The presence of variation in embryological characters amongst the species of Swertia s.l. strongly supports the view that Swertia s.l. is not a monophyletic group. Frasera is better separated from Swertia s.l. as an independent genus, and is only distantly related to Swertia s. s. judging from the numerous differences in embryology. Swertia tetraptera is very closely related to Halenia, as they show identical embryology. (C) 2007 The Linnean Society of London, Botanical Journal of the Linnean Society, 2007, 155, 383-400.

环渤海地区地壳和上地幔地震层析成像研究

In Circum-Bohai region (112°~124°E, 34°~42°N ), there exists rich gas-petroleum while inner-plate seismic activity is robust. Although the tectonic structure of this region is very complicated, plenty of geological, geophysical and geochemical researches have been carried out.In this paper, guided by the ideas of "One, Two, Three and Many" and "The depth controls the shallow, the regional constrains the local", I fully take advantage of previous results so as to establish a general image of this region. After collecting the arrival-time of P-wave phases of local events and tele-seismic events recorded by the stations within this region from 1966 to 2004, I process all these data and build an initial model. Then, a tomography image of crust and upper-mantle of this region is obtained. With reference to previous results, we compare the image of various depths and five cross-profiles traverse this region along different direction. And finally, a discussion and conclusion is made.The principle contents is listed as below: 1) in the first chapter, the purpose and meaning of this thesis, the advance in seismic tomography, and the research contents and blue-print is stated; 2) in the second chapter, I introduce the regional geological setting of Circum-Bohai region, describe the tectonic and evolutionary characteristics of principle tectonic units, including Bohai Bay Basin, Yanshan Fold Zone, Taihangshan Uplifted Zone, Jiao-Niao Uplifted Zone and Luxi Uplifted Zone, and primary deep faults; 3) In the third chapter, the previous geophysical researches, i.e., gravity and geomagnetic characters, geothermal flow, seismic activity, physical character of rocks, deep seismic sounding, and previous seismic tomography, are discussed; 4) in the fourth chapter, the fundamental theory and approach of seismic tomography is introduced; 5) in the fifth chapter, the technology and approaches used in this thesis, including collecting and pre-processing of data, the establishment of initial velocity model and relocation of all events; 6) in the sixth chapter, I discuss and analyze the tomography image of various depth and five cross-sections; 7)in the seventh chapter, I make a conclusion of the results, state the existing problems and possible solutions.

Investigation of kerosene combustion characteristics with pilot hydrogen in model supersonic combustors

Experimental investigations on the ignition and combustion stabilization of kerosene with pilot hydrogen in Mach 2.5 airflows were conducted using two test combustors, with cross sections of 30.5 x 30 and 51 x 70 mm, respectively. Various integrated modules, including the combinations of different pilot injection schemes and recessed cavity flameholders with different geometries, were designed and tested. The stagnation pressure of vitiated air varied within the range of 1.1-1.8 NiPa, while the stagnation temperature varied from 1500 to 1900 K. Specifically, effects of the pilot hydrogen injection scheme, cavity geometry, and combustor scaling on the minimally required pilot hydrogen equivalence ratio were systematically examined. Results indicated that the cavity depth and length had significant effects on the ignition and flameholding, whereas the slanted angle of the aft wall was relatively less important. Two cavities in tandem were shown to be a more effective flameholding mechanism than that with a single cavity. The minimally required pilot hydrogen equivalence ratio for kerosene ignition and stable combustion was found to be as low as 0.02. Furthermore, combustion efficiency of 80% was demonstrated to be achievable for kerosene with the simultaneous use of pilot hydrogen and a recessed cavity to promote the ignition and global burning.

K418与42CrMo异种金属的激光穿透焊接

实验研究了连续波Nd：YAG激光焊接速度、侧吹保护气流量和离焦量等参量对激光穿透焊接K418和42CrMo焊缝成形的影响。结果表明，K418与42CrMo激光穿透焊接有X形和T形两种典型的焊缝形貌，且焊缝形貌是不对称的。随着焊接速度的提高，焊接线能量降低，焊缝尺寸变小，且焊缝上部尺寸变化比下部尺寸变化慢，焊缝形貌由X形过渡到T形。当离焦量在瑞利长度范围内时，焊缝正面宽度变化很小；当离焦量超出瑞利长度范围时，在足够高的激光功率密度下，焊缝正面宽度快速增加。在激光功率为3kW，侧吹保护气角度为35°条件下，通过优化焊接速度、侧吹保护气流量和离焦量等参量可以得到最佳焊缝质量。

A Novel Inverse Method For Determining The Refractive Indices Of Medium And Dispersed Particles Simultaneously By Turbidity Measurement

The refractive indices of particles and dispersion medium are important parameters in many colloidal experiments using optical techniques, such as turbidity and light scattering measurements. These data are in general wavelength-dependent and may not be available at some wavelengths fitting to the experimental requirement. in this Study we present a novel approach to inversely determine the refractive indices of particles and dispersion medium by examining the consistency of measured extinction cross sections of particles with their theoretical values using a series of trial values of the refractive indices. The colloidal suspension of polystyrene particles dispersed in water was used as an example to demonstrate how this approach works and the data obtained via such a method are compared with those reported in literature, showing a good agreement between both. Furthermore, the factors that affect the accuracy of measurements are discussed. We also present some data of the refractive indices of polystyrene over a range of wavelengths smaller than 400 nm that have been not reported in the available literature. (C) 2008 Elsevier Inc. All rights reserved.

Toward an understanding of the turbidity measurement of fleterocoagulation rate constants of dispersions containing particles of different sizes

Our previous studies have shown that the determination of coagulation rate constants by turbidity measurement becomes impossible for a certain operating wavelength (that is, its blind point) because at this wavelength the change in the turbidity of a dispersion completely loses its response to the coagulation process. Therefore, performing the turbidity measurement in the wavelength range near the blind point should be avoided. In this article, we demonstrate that the turbidity measurement of the rate constant for coagulation of a binary dispersion containing particles of two different sizes (heterocoagulation) presents special difficulties because the blind point shifts with not only particle size but also with the component fraction. Some important aspects of the turbidity measurement for the heterocoagulation rate constant are discussed and experimentally tested. It is emphasized that the T-matrix method can be used to correctly evaluate extinction cross sections of doublets formed during the heterocoagulation process, which is the key data determining the rate constant from the turbidity measurement, and choosing the appropriate operating wavelength and component fraction are important to achieving a more accurate rate constant. Finally, a simple scheme in experimentally determining the sensitivity of the turbidity changes with coagulation over a wavelength range is proposed.

The size-dependent bending elastic properties of nanobeams with surface effects

A theoretical model is presented to investigate the size-dependent bending elastic properties of a nanobeam with the influence of the surface relaxation and the surface tension taken into consideration. The surface layer and its thickness of a nanostructure are defined unambiguously. A three-dimensional (3D) crystal model for a nanofilm with n layers of relaxed atoms is investigated. The four nonzero elastic constants of the nanofilm are derived, and then the Young's modulus for simple tension is obtained. Using the relation of energy equilibrium, the size-dependent effective elastic modulus and effective flexural rigidity of a nanobeam with two kinds of cross sections are derived, and their dependence on the surface relaxation and the surface tension is analysed.

Evaluation of influence of multiple scattering effect in light-scattering-based applications

The extinction cross sections of a system containing two particles are calculated by the T-matrix method, and the results are compared with those of two single particles with single-scattering approximation. The necessity of the correction of the refractive indices of water and polystyrene for different incident wavelengths is particularly addressed in the calculation. By this means, the volume fractions allowed for certain accuracy requirements of single-scattering approximation in the light scattering experiment can be evaluated. The volume fractions calculated with corrected refractive indices are compared with those obtained with fixed refractive indices which have been rather commonly used, showing that fixed refractive indices may cause significant error in evaluating multiple scattering effect. The results also give a simple criterion for selecting the incident wavelength and particle size to avoid the 'blind zone' in the turbidity measurement, where the turbidity change is insensitive to aggregation of two particles.

Short-surface waves radiated by a partially-immersed 3-dimensional oscillating body

The short-surface waves generated by a 3-D arbitrarily oscillating body floating onwater are discussed. In the far-field off the body, the phase and the amplitude functions ofthe radiated waves are determined by the ray method. An undetermined constant is includ-ed in the amplitude function. From the result of Ref. [1], the near-field boundary layersolution near the body waterline is obtained. The amplitude of this solution depends on thewhole wall shape of the body and the slope at the body waterline on the cross-sections per-pendicular to the waterline. By matching the far-field solution with the near-field bound-ary layer solution, the undetermined constant in the amplitude function of the far-fieldradiated waves is determined. For the special case of a half-submerged sphere which per-forms vertical oscillating motion, the result obtained in this paper is in agreement withthat of Ref. [ 2 ].

Interface Fracture Behavior Of Electroplated Coating On Metal Substrate Under Compressive Strain

The inducement of interface fracture is crucial to the analysis of interfacial adhesion between coating and substrate. For electroplated coating/metal substrate adhering materials with strong adhesion, interface cracking and coating spalling are difficult to be induced by conventional methods. In this paper an improved bending test named as T-bend test was conducted on a model coating system, i.e. electroplated chromium on a steel substrate. After the test, cross-sections of the coated materials were prepared to compare the failure behaviors under tensile strain and compressive strain induced by T-bend test. And the observation results show that coating cracking, interface cracking and partial spalling appear step by step. Based on experimental results, a new method may be proposed to rank the coated materials with strong inter-facial adhesion. (C) 2008 Elsevier B.V. All rights reserved.

Upconversion luminescence and optical power limiting effect based on two- and three-photon absorption processes of ZnO crystal

Near-infrared to UV and visible upconversion luminescence was observed in single-crystalline ZnO under an 800 nm infrared femtosecond laser irradiation. The optical properties of the crystal reveal that the UV and VIS emission band are due to the exciton transition (D0X) bound to neutral donors and the deep luminescent centers in ZnO, respectively. The relationship between the upconversion luminescence intensity and the pump power of the femtosecond laser reveals that the UV emission belongs to three-photon sequential band-to-band excitation and the VIS emission belongs to two-photon simultaneous defect-absorption induced luminescence. A saturation phenomenon and polarization-dependent effect are also observed in the upconversion process of ZnO. A very good optical power limiting performance at 800 nm has been demonstrated. The two- and three-photon absorption coefficients of ZnO crystal were measured to be 0.2018 cm GW(-1) and 7.102 x 10(-3) cm(3) GW(-2), respectively. The two- and three-photon cross sections were calculated to be 1.189 x 10(-51) cm(4) s and 1.040 x 10(-80) cm(6) s(2), respectively. (c) 2007 Elsevier B.V. All rights reserved.

Large three-photon absorption and intramolecular charge transfer of the bis-donor fluorene-based molecules

Three-photon absorption (3PA) of two fluorene-based molecules with D-pi-D structural motifs (abbreviated as BPAF and BCZF) has been determined by using a Q-switched Nd: YAG laser pumped with 38 ps pulses at 1064 nm in DMF. The measured 3PA cross-sections are 222 and 140 x 10(-78) cm(6) s(2) for BPAF and BCZF, respectively. AM1 calculations show that attaching different donors changes the charge density distribution of the fluorene skeleton, and it is observed that the 3PA cross-section can be enhanced with increasing intramolecular charge transfer character, measured by the parameter Delta p(1)/Delta p(2)/Delta p(1)'. (c) 2005 Elsevier B.V. All fights reserved.