209 resultados para Relative intensity
Resumo:
We have found that the optical power of a laser diode (LD) does not change with the injected light intensity that is modulated when its injection current is at some specific values. The amplitude of optical power change of the LD varies periodically with the increase of the injection current. It is made clear through theoretical analysis that these phenomena are caused by gain compression and interband carrier absorption of the LD that depend on longitudinal mode competition, bandgap-shrinkage effects, thermal conduction, and so on. Our experimental results make it easy to eliminate optical power change of LDs. We only need to choose a proper value of the injection current. (c) 2005 Optical Society of America.
Resumo:
We proposed a new method of measuring the degree of collimation of laser beam using axial intensity information near paraxial focus. Preceding methods for collimation testing are mainly either based on self-imaging or interferometric techniques. The new method is to employ the diffraction behavior of noncollimated wave in circular aperture diaphragm. The principle of the proposed method and experiment results are presented. Due to simplicity of the method and its low cost, it is a promising method for checking the collimation of laser beam. (c) 2005 Published by Elsevier GmbH.
Resumo:
In this paper, we propose a novel method for measuring the coma aberrations of lithographic projection optics based on relative image displacements at multiple illumination settings. The measurement accuracy of coma can be improved because the phase-shifting gratings are more sensitive to the aberrations than the binary gratings used in the TAMIS technique, and the impact of distortion on displacements of aerial image can be eliminated when the relative image displacements are measured. The PROLITH simulation results show that, the measurement accuracy of coma increases by more than 25% under conventional illumination, and the measurement accuracy of primary coma increases by more than 20% under annular illumination, compared with the TAMIS technique. (c) 2007 Optical Society of America.
Resumo:
In the sinusoidal phase modulating interferometer technique, the high-speed CCD is necessary to detect the interference signals. The reason of ordinary CCD's low frame rate was analyzed, and a novel high-speed image sensing technique with adjustable frame rate based on ail ordinary CCD was proposed. And the principle of the image sensor was analyzed. When the maximum frequency and channel bandwidth were constant, a custom high-speed sensor was designed by using the ordinary CCD under the control of the special driving circuit. The frame rate of the ordinary CCD has been enhanced by controlling the number of pixels of every frame; therefore, the ordinary of CCD can be used as the high frame rate image sensor with small amount of pixels. The multi-output high-speed image sensor has the deficiencies of low accuracy, and high cost, while the high-speed image senor with small number of pixels by using this technique can overcome theses faults. The light intensity varying with time was measured by using the image sensor. The frame rate was LIP to 1600 frame per second (f/s), and the size of every frame and the frame rate were adjustable. The correlation coefficient between the measurement result and the standard values were higher than 0.98026, and the relative error was lower than 0.53%. The experimental results show that this sensor is fit to the measurements of sinusoidal phase modulating interferometer technique. (c) 2007 Elsevier GmbH. All rights reserved.
Resumo:
On the basis of the space-time Wigner distribution function (STWDF), we use the matrix formalism to study the propagation laws for the intensity moments of quasi-monochromatic and polychromatic pulsed paraxial beams. The advantages of this approach are reviewed. Also, a least-squares fitting method for interpreting the physical meaning of the effective curvature matrix is described by means of the STWDF. Then the concept is extended to the higher-order situation, and what me believe is a novel technique for characterizing the beam phase is presented. (C) 1999 Optical Society of America [S0740-3232(99)001009-1].
Resumo:
By means of the Huygens-Fresnel diffraction integral, the field representation of a laser beam modulated by a hard-edged aperture is derived. The near-field and far-field transverse intensity distributions of the beams with different bandwidths are analyzed by using the representation. The numerical calculation results indicate that the amplitudes and numbers of the intensity spikes decrease with increasing bandwidth, and beam smoothing is achieved when the bandwidth takes a certain value in the near field. In the far field, the radius of the transverse intensity distribution decreases as the bandwidth increases, and the physical explanation of this fact is also given. (c) 2005 Optical Society of America.
Resumo:
The propagation expression of a broadband laser passing through a dispersive wedge is derived on the basis of the Huygens-Fresnel diffraction integral, Smoothing effects caused by the phase perturbation of the dispersive wedge on the intensity profiles are investigated in detail. The phase perturbation of the dispersive wedge induces a relative transverse position shift between the diffraction patterns of different frequency components. The relative transverse position shift is of great benefit to the fill of the intensity peaks of some patterns in the valleys of others when these patterns are overlapped and thus the smoothing effect is achieved. (c) 2006 Elsevier B.V. All rights reserved.
Resumo:
Starting from the Huygens-Fresnel diffraction integral and the Fourier transform, the propagation expression of a chirped pulse passing through a hard-edged aperture is derived. Using the obtained expression, the intensity distributions of the pulse with different chirp in the near and far fields are analyzed in detail. Due to the modulation of the aperture, many intensity peaks emerge in the intensity distributions of the chirped pulse in the near field. However, the amplitudes of the intensity peaks decrease on increasing the chirp, which results in the smoothing effect in the intensity distributions. The beam smoothing brought by increasing the chirp is explained physically. Also, it is found that the radius of the intensity distribution of the chirped pulse decreases when the chirp increases in the far field. (c) 2005 Elsevier GmbH. All rights reserved.
Resumo:
We propose a new method to increase the resolution of an optical system by modifying part of the spatial-frequency spectrum, viz., displacing the lower-frequency light to a high-frequency band, which makes the central maximum in the diffraction pattern narrower and increases the depth of focus. Simulation results show that this kind of apodizer (the term apodization was originally used to describe ways to reduce the sidelobes of the PSF, but in this paper, we use it in a wider sense) is superior to the phase-shifting ones. (C) 2001 Society of Photo-Optical Instrumentation Engineers.
Resumo:
The three-dimensional distribution of light intensity that is modulated by a pure phase-shifting apodizer is studied. Results show that the Strehl ratio can be altered by the proposed apodizer and by the waist width of incident Gaussian beams. By changing geometrical parameters of the proposed apodizer, we can increase the focal depth to several times that of the original system. The proposed apodizer can also be used to realize focal splitting and local minimum of intensity, which may be advantageous for constructing an optical trap. Furthermore, the local minimum of intensity number is tunable by changing the parameters of the apodizer. (c) 2005 Optical Society of America
Resumo:
采用有损耗介质和色散介质的二维时域有限差分方法,数值模拟了以光波长514.5 nm的p偏振基模高斯光束为入射光源,激发Kretschmann型表面等离子体共振,并通过探针的局域场增强效应实现纳米光刻的新方法——探针诱导表面等离子体共振耦合纳米光刻.分别就探针与记录层的间距以及探针针尖大小,模拟分析了不同情况下探针的局域场增强效应和记录层表面的相对电场强度振幅分布.结果表明,探针工作在接触模式时,探针的局域场增强效应最明显,记录层表面的相对电场强度振幅的对比度最大;当探针针尖距记录层5 nm时,针尖下方记录层表面的相对电场强度振幅大于光刻临界值的分布宽度与针尖尺寸相近.
Resumo:
Partially end-pumped slab laser is an innovative solid state laser, namely InnoSlab. Combining the hybrid resonator with partially end-pumping, the output power can be scaled with high beam quality. In this paper, the output intensity distributions are simulated by coordinate transformation fast Fourier transform (FFT) algorithm, comparing the thermal lens influence. As the simulated curves showed, the output mode is still good when the thermal lens effect is strong, indicating the good thermal stability of InnoSlab laser. Such a new kind of laser can be designed and optimized on the base of this simulation.