Alkaline treatment of the cellulose fiber affecting membrane column behaviour for high-performance immunoaffinity chromatography

The original cellulose fibers and those treated by alkaline solution were both used to prepare the acrylic membranes. The two kinds of membranes were packed into the columns for high-performance immunoaffinity chromatography by the immobilization of protein A on them. It was observed that the alkaline treatment of the cellulose fiber decreased the pressure resistance of the membrane to the mobile phases and greatly increased the accessible volume to the proteins, but affected the adsorption capacity of human IgG on the protein A membrane columns less. There is little difference between those two kinds of membranes on the adsorption capacities of HIgG, which means that the alkaline treatment of the cellulose fiber only significantly changes the void volume inter-membrane, and the porosity and surface area of membrane less. Alkaline treatment of the cellulose fiber reduced the membrane-column efficiency significantly. Some typical examples for the immunoaffinity analysis of IgG from human and dog plasma on the protein A membrane columns are illustrated. Copyright (C) 2000 John Wiley & Sons, Ltd.

Heat capacities of Al62.5Cu25Fe12.5 quasicrystals and B2 related crystals

The heat capacities of two Al62.5Cu25Fe12.5 samples containing icosahedral quasicrystals and B2 related crystals respectively were measured with a high-precision automatic adiabatic calorimeter over the temperature range of 75-385 K. The heat capacities of both samples increase with temperature. At the low temperature range, the heat capacity of the quasicrystalline sample is higher than that of the B2 approximate. However, the heat capacity of the B2 sample becomes higher above 254.987 K. (C) 1999 Elsevier Science B.V. All rights reserved.

Enhancement of boron removal in treatment of spent rinse from a plating operation using RO

Boron removal is a critical issue in the production of drinking water and of ultra-pure water in the electronics industry. Boron rejection in a RO process is typically in the range of 40-60%. The objective of this study was to distinguish the factor contributing to enhanced boron rejection in reclamation of a spent rinse stream from a plating operation. The effects of different known components used in the feed on boron removal were investigated in the laboratory. The results indicated that glycolic acid and antifoulants could not individually enhance boron rejection in a RO process. A high boron rejection of 95% was achieved as the concentration of iron in the feed was 10 times higher than that of boron, which might be due to formation of a complex between iron oxide and boron. The finding was confirmed in a pilot study.

Low temperature heat capacity of (S)-ibuprofen

Molar heat capacities of ( S)-ibuprofen were precisely measured with a small sample precision automated adiabatic calorimeter over the temperature range from 80 to 370 K. Experimental heat capacities were fitted into a polynomial equation of heat capacities ( C-p,C- m) with reduced temperature ( X), [ X = f(T)]. The polynomial equations for ( S)-ibuprofen were C-p,C- m(s) = - 39.483 X-4 - 66. 649 X-3 + 95. 196 X-2 + 210. 84 X + 172. 98 in solid state and C-p,C- m(L) = 7. 191X(3) + 4. 2774 X-2 + 56. 365 X + 498. 5 in liquid state. The thermodynamic functions relative to the reference temperature of 298. 15 K, H-T - H-298.15 and S-T - S-298.15, were derived for the( S)-ibuprofen. A fusion transition at T-m = (324. 15 +/- 0. 02) K was found from the C-p - T curve. The molar enthalpy and entropy of the fusion transition were determined to be (18. 05 +/- 0. 31) kJ.mol(-1) and (55. 71 +/- 0. 95) J.mol(-1).K-1, respectively. The purity of the ( S)-ibuprofen was determined to be 99. 44% on the basis of the heat capacity measurement. Finally, the heat capacities of ( S)-ibuprofen and racemic ibuprofen were compared.

Measurements of the heat capacity of an azeotropic mixture of water and n-butanol from 78 to 320 K

Molar heat capacities of n-butanol and the azeotropic mixture in the binary system [water (x=0.716) plus n-butanol (x=0.284)] were measured with an adiabatic calorimeter in a temperature range from 78 to 320 K. The functions of the heat capacity with respect to thermodynamic temperature were established for the azeotropic mixture. A glass transition was observed at (111.9 +/- 1.1) K. The phase transitions took place at (179.26 +/- 0.77) and (269.69 +/- 0.14) K corresponding to the solid-liquid phase transitions of. n-butanol and water, respectively. The phase-transition enthalpy and entropy of water were calculated. A thermodynamic function of excess molar heat capacity with respect to temperature was established, which took account of physical mixing, destructions of self-association and cross-association for n-butanol and water, respectively. The thermodynamic functions and the excess thermodynamic ones of the binary systems relative to 298.15 K were derived based on the relationships of the thermodynamic functions and the function of the measured heat capacity and the calculated excess heat capacity with respect to temperature.