Dye-Sensitized Solar Cells with a High Absorptivity Ruthenium Sensitizer Featuring a 2-(Hexylthio)thiophene Conjugated Bipyridine

We conjugated 2-(hexylthio)thiophene with bipyridine to construct a new heteroleptic polypyridyl ruthenium sensitizer exhibiting a charge-transfer band at 550 nm with a molar extinction coefficient of 18.7 x 10(3) M-1 cm(-1). In contrast to its analogues Z907 and C101, a mesoporous titania film stained with this new sensitizer featured a short light absorption length, allowing for the use of a thin photoactive layer for efficient light-harvesting and conversion of solar energy to electricity. With a preliminary testing, we have reached 11.4% overall power conversion efficiency measured at the air mass 1.5 global conditions. Transient photoelectrical decays and electrical impedance spectra were analyzed to picture the intrinsic physics of temperature-dependent photovoltage and photocurrent.

An Extremely High Molar Extinction Coefficient Ruthenium Sensitizer in Dye-Sensitized Solar Cells: The Effects of pi-Conjugation Extension

We report a heteroleptic ruthenium complex (007) featuring the electron-rich 5-octyl-2,2'-bis(3,4-ethylenedioxythiophene) moiety conjugated with 2,2-bipyridine and exhibiting 10.7% power conversion efficiency measured at the AM1.5G conditions, thanks to the enhanced light-harvesting that is closely related to photocurrent. This C107 sensitizer has an extremely high molar extinction coefficient,of 27.4 x 10(3) M-1 cm(-1) at 559 nm in comparison to its analogue C103 (20.5 x 10(3) M-1 cm(-1) at 550 nm) or Z907 (12.2 x 10(3) M(-1)cm(-1) at 521 nm) with the corresponding 5-hexyl-3,4-ethylenedioxythiopliene- or nonyl-substituted bipyridyl unit. The augmentation of molar extinction coefficients and the bathochromic shift of low-energy absorption peaks along with the pi-conjugation extension are detailed by TD-DFT calculations. The absorptivity of mesoporous titania films grafted with Z907, C103, or C107 sublinearly increases with the molar extinction coefficient of sensitizers, which is consistent with the finding derived from the surface coverage measurements that the packing density of those sensitizers decreases with the geometric enlargement of ancillary ligands.

Solid-state dye-sensitized solar cells using TiO2 nanotube arrays on FTO glass

Highly ordered, vertically oriented TiO2 nanotube arrays were prepared by potentiostatic anodization of titanium on FTO-coated glass substrate and for the first time successfully applied in the fabrication of solid-state dye sensitized solar cells (SSDSCs), giving a power conversion efficiency of 1.67% measured under an irradiation of air mass 1.5 global (AM 1.5 G) full sunlight. Furthermore, 3.8% efficiency was reached with a 2.8 mu m thin TiO2 nanotube array film based on a metal free organic dye using ionic liquid electrolyte.

Toward high-performance polymer solar cells: The importance of morphology control

Polymer solar cells have the potential to become a major electrical power generating tool in the 21st century. R&D endeavors are focusing on continuous roll-to-roll printing of polymeric or organic compounds from solution-like newspapers-to produce flexible and lightweight devices at low cost. It is recognized, though, that besides the functional properties of the compounds the organization of structures on the nanometer level-forced and controlled mainly by the processing conditions applied-determines the performance of state-of-the-art polymer solar cells. In such devices the photoactive layer is composed of at least two functional materials that form nanoscale interpenetrating phases with specific functionalities, a so-called bulk heterojunction. In this perspective article, our current knowledge on the main factors determining the morphology formation and evolution is introduced, and gaps of our understanding on nanoscale structure-property relations in the field of high-performance polymer solar cells are addressed. Finally, promising routes toward formation of tailored morphologies are presented.

Organic photovoltaic cells with near infrared absorption spectrum

Organic photovoltaic cells with a strong absorption spectrum in the near infrared region were fabricated with the structure of indium tin oxide (ITO)/zinc phthalocynine (ZnPc)/lead phthalocynine (PbPc)/C-60/Al. PbPc has a broad and strong absorption, while the organic films of PbPc/C-60 showed an additional new absorption peak at 900 nm. The absorption in the near infrared region can harvest more photons to invert into photocurrent. Moreover, the introduction of ZnPc thin layer between ITO and PbPc further improved the new absorption peak and the collection of hole carriers at the electrode ITO, which increased the power conversion efficiencies to 1.95% and short-circuit current density to 9.1 mA/cm(2) under AM 1.5 solar spectrum.

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton-exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2'-bis(p-aminophenoxy)-1,1'-binaphthyl-6,6'-disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30-80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film-forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945-0.161 S/cm) at 20-80 degrees C in liquid water. The membranes exhibited methanol permeability from 9 x 10(-8) to 5 X 10(-7) cm(2)/s at 20 degrees C, which was much lower than that of Nafion (2 x 10(-6) cm(2)/s). The copolymers were thermally stable up to 300 degrees C. The sulfonated polyimide copolymers with 30-60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability.

Preparation and properties of sulfonated poly(ether ether ketone)s (SPEEK)/polypyrrole composite membranes for direct methanol fuel cells

Polypyrrole (Ppy) was successfully introduced into methyl substituted sulfonated poly(ether ether ketone) (SPEEK) membranes by polymerization in SPEEK solutions to improve their methanol resistance. Uniform polypyrrole (Ppy) distributed composite membranes were formed by this method by the interaction between SPEEK and Ppy. The properties of the composite membranes were characterized in detail. The composite membranes show very good proton conductive capability (25 degrees C: 0.05-0.06s cm(-1)) and good methanol resistance (25 degrees C: 5.3 x 10(-7) 1.1 x 10(-6) cm(2) s(-1)). The methanol diffusion coefficients of composite membranes are much lower than that of pure SPEEK membranes (1.5 x 10(-6) cm(2) s(-1)). The composite membranes show very good potential usage in direct methanol fuel cells (DMFCs).

Synthesis, characterization and electrical properties of the new solid electrolyte materials Ce6-xErxMoO15-delta (0.0 < x < 1.5)

A new series of oxides, Ce6-xErxMoO15-delta (0.0 less than or equal to x less than or equal to 1.5), was synthesized using wet-chemistry techniques. The precursors and resultant oxide powders were characterized by differential thermal analysis/thermogravimetry, x-ray diffraction, and IR, Raman and x-ray photoelectron spectroscopy. The formation temperature of the powders was found to be as low as 350degreesC. Ce6-xErxMoO15-delta crystallized to a fluorite-related cubic structure. The electrical conductivity of the samples was investigated by using ac impedance spectroscopy. This showed that the presence of Er was related to the oxygen-ion conductivity, and that the highest oxygen-ion conductivity was found in Ce6-xErxMoO15-delta (x = 0.4), ranging from 5.9 x 10(-5) S cm(-1) at 300degreesC to 1.26 x 10(-2) S cm(-1) at 700degreesC, respectively. This kind of material shows a potential application in intermediate-temperature solid oxide fuel cells.

Efficient green electroluminescent cells using a poly(p-phenylene vinylene) multiblock copolymer sandwiched between carrier-transporting layers

With a newly synthesized poly(p-phenylene vinylene) (PPV) multiblock copolymer used in a triple-layer structure, efficient green light-emitting diodes with low driving voltage have been fabricated. The devices are turned on at 2.5 V, the brightness at 5 V is above 100 cd/m(2) and at 7 V is about 1650 cd/m(2), with an external quantum efficiency of about 1%. (C) 1998 Elsevier Science S.A. All rights reserved.

Study on the GABA gated channels in the neurosecretory cells of MTXO in the eyestalks of Eriocheir sinensis

The responses to rapid application of gamma-aminobutyric acid (GABA) and the GABA receptor characteristics of MTXO neurosecretory cells in the eyestalks of Chinese mitten-handed crab (Eriocheir sinensis) were examined by whole-cell patch clamp. Under current clamp mode, the depolarization and hyperpolarization were evoked from the three types of neurosecretory cells in response to the GABA (0.1 mmol/L) depending on the Nernst Cl- potential. Under voltage clamp mode, the inward Cl- channel currents (I-GABA) were resolved from all three types of neurosecretory cells in response to GABA (0.01similar to5 mmol/L). The GABA currents were activated within 1 200 ms and peaked within 800 ms. No obviously desensitization was observed during GABA application. The dose-response curve showed usual S-shape, with a just-discernible effect at 0.01 mmol/L and near-saturation at 0.5 mmol/L. The GABA currents had reversal potentials that followed Nernst Cl- potentials when [Cl-] was varied. The pharmacological results revealed that the GABA receptor of the crab neurosecretory cells was sensitive to the Cl- channel blockers picrotoxin and niflumic acid (0.5 mmol/L), insensitive to GABA(A) receptor antagonist bicuculline and GABA(C) receptor agonist cis-4-aminocrotonic acid (CACA 1 mmol/L) and trans-4-aminocrotonic (TACA 1 mmol/L).

Rapid optimization of process conditions for cultivation of transgenic Laminaria japonica gametophyte cells in a stirred-tank bioreactor

Batch cultivation for transgenic kelp gametophyte cells was investigated in an online controlled 5 L stirred-tank photo-bioreactor to rapidly optimize the process conditions by monitoring the rate of increase of pH. The transgenic kelp gametophytes with heterologous gene encoding hepatitis B surface antigen (HBsAg) could rapidly grow in the bioreactor. Optimal temperature and agitation rate for bioreactor cultivation of gametophytes were 15 degrees C and 200 rpm. Optimal incident light intensities depended on the initial cell densities. (c) 2006 Elsevier B.V. All fights reserved.

Molecular structure and expression patterns of flounder (Paralichthys olivaceus) Myf-5, a myogenic regulatory factor

Myf-5, a member of the myogenic regulatory factors (MRF), has been shown to be expressed in muscle precursors in early stage zebrafish embryos. The MRFs, including MyoD, Myf-5, Myogenin and MR-F4, belong to the basic Helix-Loop-Helix transcription factors that contain a conserved basic Helix-Loop-Helix (bHLH) domain. To better understand the role of Myf-5 in the development of fish muscles, we have isolated the Myf-5 genomic sequence and cDNA from Flounder (Paralichthys olivaceus), and analyzed its structures and patterns of expression. Promoter analysis identified several putative transcription factor binding sites such as an E-box, NF-Y sites that might confer muscle-specific expression. Myf-5 transcripts were first detected in the paraxial mesoderm that gives rise to slow muscles. During somitogenesis, Myf-5 expression was found in developing somites. Myf-5 expression decreased gradually in somites in the anterior region, but remained strong in the newly formed somites. In the hatching stage, the expression was also detected in other muscle cells such as head muscle and fin muscle. In the growing fish, RT-PCR results showed that Myf-5 was expressed in the skeletal muscle and intestine. (c) 2006 Elsevier Inc. All rights reserved.

Inhibition of egg hatching success and larvae survival of the scallop, Chlamys farreri, associated with exposure to cells and cell fragments of the dinoflagellate Alexandrium tamarense

We report an apparently novel toxic effect of the dinoflagellate Alexandrium tamarense, manifested by inhibition of the egg hatching success of the scallop, Chlamys farreri. The hatching rate of C. farreri approached only 30% of controls when its fertilised eggs were exposed for 36 h to A. tamarense cells or cellular fragments at a concentration of 100 cells/ml, and the hatching rate was just 5% after exposure to A. tamarense of 500 cells/ml. Similar exposures of the fertilised scallop eggs to two other algal species, the diatom Phaeodactylum tricornutum and the raphidophyte Heterosigma carterae, resulted in no such toxicity or inhibitory effects.. Likewise, exposure of eggs to standard STX toxin. as well as to A. tamarense cell contents (supernant of re-suspended algal cells following ultrasonication and centrifugation), did not elicit this inhibitory response. However, exposure of the scallop eggs to cell cultures, intact algal cells, or cell fragments of A. tamarense produced marked toxicity. The alga also influenced larvae at early D-shape stage of scallop. The survival rates began to decrease significantly after exposed for 6 days at concentration of 3000 cells/ml and above: no larvae could survive after 14-day exposure to A. tamarense at 10,000 cells/ml or 20-day at 5000 cells/ml. The results indicated the production of novel substances from A. tamarense which can cause adverse effects on egg hatching and survival of the scallop larvae, The experiment also found that the developmental stages before blastula was the developmental period most sensitive to the A. tamarense toxin(s) and the alga at early exponential stage had the strongest effect on egg hatching comparing with other growth phases. The adverse effect of A. tamarense on early development of scallops may cause decline of shellfish population and may have further impact on marine ecosystem. (C) 2001 Elsevier Science Ltd. All rights reserved.

Proteomic detection of changes in protein expression induced by cordycepin in human hepatocellular carcinoma BEL-7402 cells

The nucleoside analogue cordycepin (3'-deoxyodenosine, 3'-dA), one of the components of cordyceps militaris, has been shown to inhibit the growth of various tumor cells. However, the probable mechanism is still obscure. In this study, the inhibition of cell growth and changes in protein expression induced by cordycepin were investigated in BEL-7402 cells. Using the MTT assay and flow cytometry, we found that cordycepin inhibits cell viability and induces apoptosis in BEL 7402 cells. Additionally. the proteins were separated using two-dimensional polyacrylamide gel electrophoresis, and eight proteins were found to be significantly, affected by cordycepin compared to untreated control; among them, two were downregulated and six were upregulated. Of the eight proteins, six were identified with peptide mass fingerprinting using matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS) after in-gel trypsin digestion. These proteins are involved in various aspects of cellular metabolism. It is suggested that the effect of cordycepin on the growth of tumor cells is significantly related to the metabolism-associated protein expression induced by cordycepin. Copyright 2008 Prous Science, S.A.U. or its licensors. All rights reserved.