Microstructures and tensile properties of Mg-8Gd-0.6Zr-xNd-yY (x+y=3, mass%) alloys

Mg-8Gd-0.6Zr-xNd-yY (mass%) alloys which containing different Nd:Y mass ratio of 3:0, 2:1, 1:2 and 0:3 with a constant x + y = 3 were prepared by metal mould casting method, and the microstructure, aging behaviour and tensile properties have been investigated. The fibrous eutectic areas along the boundaries enlarge clearly in the as-cast alloys containing Y element, and the fine grain boundaries and dispersed precipitation are observed in the aged alloys. The Mg-8Gd-0.6Zr-2Nd-Y alloy exhibits notably age-hardening behaviour and the highest mechanical property. The ultimate tensile strength and yield strength of Mg-8Gd-0.6Zr-2Nd-Y alloy in the peak aged hardness are 293 and 221 MPa at room temperature, 248 and 191 MPa at 230 degrees C. The improvement of age-hardening response and tensile properties is mainly attributed to the quadrate-like stable Mg5RE precipitate, which forms readily and orderly in aged Mg-8Gd-0.6Zr-2Nd-Y alloy.

Hydrothermal synthesis and crystal structure of a novel compound: [Ni(phen)(3)](2)[(SiMo10V2O40)-O-IV((VO)-O-IV)2]center dot 2H(2)O

A novel compound [Ni(phen)(3)](2)[(SiMo10V1/2O40)-O-V((VO)-O-IV)(2)] . 2H(2)O has been hydrothermally synthesized and structurally characterized by single-crystal X-ray diffraction. The compound crystallizes in the triclinic, system, space group P-1, a = 12.378(4) Angstrom, b = 14.148(5) Angstrom, c = 14.316(2) Angstrom, alpha = 105.91(2)degrees, beta = 95.31(2)degrees, gamma = 96.89(3)degrees, V = 2373.0(12) Angstrom(3), Z = 1, (lambdaMo(Kalpha)) = 0.71073 Angstrom, R1 (wR2) = 0.0869(0.2174). Data were collected on a Siemens P4 four-circle diffractometer at 293 K in the range of 1.51 < theta < 22.50degrees using the omega-scan technique. Empirical absorption correction (psi scan) was applied. The structure was solved by the direct method and refined by the Full-matrix least-squares on F-2 using the SHELXL-97 software. X-ray crystallographic study showed that the title compound contained a bi-capped alpha-Kegin-type [(SiMo10V2O40)-O-IV((VO)-O-IV)(2)](4-) polyoxoanion.

Hydrothermal synthesis and crystal structure of an unusual compound: [Cu(en)(2)](4)[(SiMo8V4O40)-O-V((VO)-O-IV)(2)][MoO4](2)center dot 5H(2)O

A novel compound [Cu(en)(2)](4)[(SiMo8V4O40)-O-v(V-IV O)(2)] [MoO4](2) . 5H(2)O has been hydrothermally synthesized and structurally characterized by single-crystal X-ray diffraction. Black crystals crystallize in the tetragonal. system, space group 14/m, a = b = 14.019(2) Angstrom, c = 20.341(4) Angstrom, V = 3997.9(11) Angstrom(3), Z = 2, lambda(MoKalpha) = 0.71073 Angstrom (R(F) = 0.0443 for 1819 reflections). Data were collected on a Siemens P4 four-circle diffractometer at 293 K in the range of 1.76 < theta < 24.98degrees using the omega-scan technique. The structure was solved by the direct method and refined by the full-matrix least squares on F-2 method using the SHELXL-97 software. X-ray crystallographic study showed that the title compound contained a bicapped alpha-Keggin fragment [SiMo8 (V4O40)-O-v((VO)-O-IV)(2)](4-) polyoxoanion.

Hydrothermal synthesis and crystal structure of [{Cu(2,2 '-bpy)(2)}(2)Mo8O26]: a beta-octamolybdate cluster covalently bonded to two {Cu(2,2 '-bpy)(2)}(2+) coordination complexes via bridging oxo groups

An organic-inorganic hybrid solid, (Cu(2,2'-bpy)(2))(2)Mo8O26, has been hydrothermally synthesized and structurally characterized by single-crystal X-ray diffraction. Dark green crystals crystallize in the orthorhombic system, space group Pna21, a = 24.164(5), b = 18.281(4), c = 11.877(2) Angstrom, alpha = 90 degrees, beta = 90 degrees, gamma = 90 degrees, V= 5247(2) Angstrom (3), Z = 4, lambda (MoK alpha) = 0.71073 Angstrom (R(F) = 0.0331 for 5353 reflections). Data were collected on a Siemens P4 four-circle diffractometer at 293 K in the range 1.69 degrees < theta < 25.04 degrees using the omega -scan technique. The structure was solved by the direct method and refined by full-matrix least squares on F-2 using SHELXL-93. The structure of this compound consists of discrete (Cu(2,2'-bpy)(2))(2)Mo8O26 clusters, constructed from beta -octamolybdate subunits ((Mo8O26)(4-)) covalently bonded to two (Cu(2,2'-bpy)(2))(2+) coordination complexes via bridging oxo groups that connect two adjacent molybdenum sites. (C) 2001 Academic Press.

Experimental measurement of polyethylene chain modulus by scanning force microscopy

Nanoindentation technique and scanning force microscopy have been used to measure directly the polyethylene modulus along the chain axis. Single crystals of polyethylene were employed in order to obtain well-aligned chain segments. To minimize effects of scanner creep, a Z scan rate of 3 Hz was employed. The "X Rotate" value of 25 degrees was selected to eliminate effects of lateral tip motion. The results were analyzed by the Oliver -Pharr method for which direct observation and measurement of the contact area are not required. Considering the influence of tip roundness on the projected contact area, the nanoindentation results were analyzed by the Sawa method. The chain modulus obtained from the thinner polyethylene single crystal sample was 204 +/- 21 GPa by the Oliver-Pharr method and 168 +/- 17 GPa by the Sawa method. The lower values than expected were due to substrate effects and anisotropy of chain deformation during nanoindentation. An extrapolation of the chain modulus obtained by various strains to zero nanoindentation eliminated the effect of substrate and anisotropy of chain deformation. The corresponding chain modulus obtained from the thicker sample was 278 GPa by the Oliver-Pharr method and 267 GPa by the Sawa method, respectively, in better agreement with the value of 340 Cpa determined theoretically. (C) 2001 Elsevier Science Ltd. All rights reserved.

Preparation of the phosphor BaMgAl10O17 : Eu2+ by the surface diffusion method

A surface diffusion method was proposed and applied to prepare blue phosphor BaMgAl10O17:Eu2+. The results show that, compared with the direct synthesis method by common high temperature solid state, the concentration of Eu2+ in the phosphor BaMgAl10O17:Eu2+ prepared by the surface diffusion method can be greatly reduced owing to the activator Eu2+ ions distributed mainly over the surface of the phosphor. It is possible to reduce the cost of this kind of the luminescent materials with the aid of the surface diffusion method.

STUDIES ON ORGANOLANTHANIDE COMPLEXES .40. SYNTHESIS AND X-RAY STRUCTURE OF BIS (2-METHOXYETHYLCYCLOPENTADIENYL) YTTRIUM AND YTTERBIUM TETRAHYDROBORATES

New bis (2-methoxyethylcyclopentadienyl) yttrium and ytterbium tetrahydroborates (Ln = Y, 1; Yb, 2) have been synthesized in good yield by the reaction of bis (2-methoxyethylcyclopentadienyl) lanthanide chlorides (Ln = Y, Yb) with sodium borohydride in THF at room temperature. The title complexes were characterized by elemental analyses, MS, H-1 NMR and IR spectra. The crystal structures of 1 and 2 have been determined by X-ray diffraction. 1 crystallizes from THF-n-Hexane in space group Pna2(1) with unit cell parametert: a = 1.2390(3), b = 1.1339(2), c = 1.1919 (2) nm and V = 1.6745(6) nm3 with z = 4 for D(c) = 1.39 g.cm-3.The structure was solved by direct method and refined to final R = 0.061 (for 1730 observed reflections). The Space group of 2 is Pna2(1) with unit cell parameters: a = 1.2399(6), b = 1.1371(5), c = 1.1897(2) nm and V = 1.6773(1) nm3 with z = 4 for D(c) = 1.72 g.cm-3, R = 0.038 (for 2157 observed reflections). The X ray structures and IR reveal the bidentate yttrium and ytterbium tetrahydroborate complexes with the intramolecular coordination bonds between lanthanide metal and ligand oxygen atoms.

Preparation of porous chitosan/agarose microsphere and its R-phycoerythrin release properties

The chitosan microspheres (CS-CL) were prepared by suspension crosslinking method and used as carriers of R-phycoerythrin (R-PE). In this study, R-PE was loaded in the microspheres and released in vitro. The effects of pH value, temperature, ionic strength, and R-PE concentration on loading efficiency and release behavior were discussed. A novel microsphere that contained agarose (CS-AR MP) was prepared and the basic loading and releasing behavior for R-PE of this kind of new micro-spheres were also investigated. The results showed that all these chitosan microspheres have the ability to control-release R-PE. The addition of agarose may somewhat accelerate the release rate of R-PE from microspheres and reduce the capacity of adsorption for R-PE. (c) 2006 Wiley Periodicals, Inc.

Ship-board measurements and estimations of air-sea fluxes in the western tropical Pacific during TOGA COARE

Direct air-sea flux measurements were made on RN Kexue #1 at 40 degrees S, 156 degrees E during the Tropical Ocean Global Atmosphere (TOGA) Coupled Ocean-Atmospheric Response Experiment (COARE) Intensive Observation Period (IOP). An array of six accelerometers was used to measure the motion of the anchored ship, and a sonic anemometer and Lyman-alpha hygrometer were used to measure the turbulent wind vector and specific humidity. The contamination of the turbulent wind components by ship motion was largely removed by an improvement of a procedure due to Shao based on the acceleration signals. The scheme of the wind correction for ship motion is briefly outlined. Results are presented from data for the best wind direction relative to the ship to minimize flow distortion effects. Both the time series and the power spectra of the sonic-measured wind components show swell-induced ship motion contamination, which is largely removed by the accelerometer correction scheme, There was less contamination in the longitudinal wind component than in the vertical and transverse components. The spectral characteristics of the surface-layer turbulence properties are compared with those from previous land and ocean results, Momentum and latent heat fluxes were calculated by eddy correlation and compared to those estimated by the inertial dissipation method and the TOGA COARE bulk formula. The estimations of wind stress determined by eddy correlation are smaller than those from the TOGA COARE bulk formula, especially for higher wind speeds, while those from the bulk formula and inertial dissipation technique are generally in agreement. The estimations of latent heal flux from the three different methods are in reasonable agreement. The effect of the correction for ship motion on latent heat fluxes is not as large as on momentum fluxes.

Simultaneous enumeration of diatom, protozoa and meiobenthos from marine sediments using Ludox-QPS method

The Ludox-QPS method is a newly developed technique, which combines the Ludox HS 40 density centrifugation and quantitative protargol stain, to enumerate marine ciliates with good taxonomic resolution. We tested the method for simultaneous enumeration of diatoms, protozoa and meiobenthos and compared its extraction efficiency for meiobenthos with that of the routine Ludox-TM centrifugation and a modified protocol using Ludox HS 40. We conducted the evaluation with a sample size of 8.3 ml each from sandy, muddy-sand and muddy sediments collected from the intertidal area of the Yellow Sea in summer 2006 and spring 2007. The Ludox-QPS method not only produced high extraction efficiencies of 97 +/- 1.3% for diatoms and 97.6 +/- 0.8% for ciliates, indicating a reliable enumeration for eukaryotic microbenthos, but also produced excellent extraction efficiencies of on average 97.3% for total meiobenthos, 97.9% for nematodes and 97.8% for copepods from sands, muddy sands and mud. By contrast, the routine Ludox-TM centrifugation obtained only about 74% of total meiobenthos abundance with one extraction cycle, and the modified Ludox HS 40 centrifugation yielded on average 93% of total meiobenthos: 89.4 +/- 2.0% from sands, 93 +/- 4.1% from muddy sands and 97.1 +/- 3.0% from mud. Apart from the sediment type, sample volume was another important factor affecting the extraction efficiency for meiobenthos. The extraction rate was increased to about 96.4% when using the same modified Ludox centrifugation for a 4 ml sediment sample. Besides the excellent extraction efficiency, the Ludox-QPS method obtained higher abundances of meiobenthos, in particular nematodes, than the routine Ludox centrifugation, which frequently resulted in an uncertain loss of small meiobenthos during the sieving process. Statistical analyses demonstrated that there were no significant differences between the meiobenthos communities revealed by the Ludox-QPS method and the modified Ludox HS 40 centrifugation, showing the high efficiency of the Ludox-QPS method for simultaneous enumeration of diatom, protozoa and meiobenthos. Moreover, the comparatively high taxonomic resolution of the method, especially for diatoms and ciliates, makes it feasible to investigate microbial ecology at community level.

2,3,5-triphenyl-2H-tetrazolium chloride and 2,4,6-tri(2-pyridyl)-s-triazine on the corrosion of mild steel in HCl

Electrochemical measurement, quantum chemical method, and scanning electron microscopy (SEM) were performed to investigate the inhibitive effect of 2,3,5-triphenyl-2H-tetrazolium chloride (TTC) and 2,4,6-tri(2-pyridyl)-s-triazine(TPT) on the corrosion of mild steel in 1mol.L-1 HCl at room temperature. Impedance spectroscopy measurement showed that the polarization resistance increased and that double layer capacitance decreased with the increase in the inhibitive concentration, and the results of potentiodynamic polarization showed that the inhibitors suppressed both cathodic and anodic processes of steel corrosion without change in the mechanism. Higher the orbital density distribution strength of the lowest unoccupied molecular orbital, higher is the molecule dipole, and lower energy gap between the energy of the highest occupied molecular orbital and the energy of the lowest unoccupied molecular orbital resulted in higher inhibitory efficiency. The results of SEM analysis showed that the metal was protected from aggressive corrosion by the addition of TTC and TPT.

Analysis of primary aromatic amines using precolumn derivatization by HPLC fluorescence detection and online MS identification

2-(2-Phenyl-1H-phenanthro-[9,10-d]imidazole-1-yl)-acetic acid (PPIA) and 2-(9-acridone)-acetic acid (AAA), two novel precolumn fluorescent derivatization reagents, have been developed and compared for analysis of primary aromatic amines by high performance liquid chromatographic fluorescence detection coupled with online mass spectrometric identification. PPIA and AAA react rapidly and smoothly with the aromatic amines on the basis of a condensation reaction using 1-ethyl-3-(3dimethylaminopropyl)-carbodiimide (EDC) as dehydrating catalyst to form stable derivatives with emission wavelengths at 380 and 440 nm, respectively. Taking six primary aromatic amines (aniline, 2-methylaniline, 2-methoxyaniline, 4-methylaniline, 4-chloroaniline, and 4-bromoaniline) as testing compounds, derivatization conditions such as coupling reagent, basic catalyst, reaction temperature and time, reaction solvent, and fluorescent labeling reagent concentration have also been investigated. With the better PPIA method, chromatographic separation of derivatized aromatic amines exhibited a good baseline resolution on an RP column. At the same time, by online mass spectrometric identification with atmospheric pressure chemical ionization (APCI) source in positive ion mode, the PPIA-labeled derivatives were characterized by easy-to-interpret mass spectra due to the prominent protonated molecular ion m/z [M + H](+) and specific fragment ions (MS/MS) m/z 335 and 295. The linear range is 24.41 fmol-200.0 pmol with correlation coefficients in the range of 0.9996-0.9999, and detection limits of PPIA-labeled aromatic amines are 0.12-0.21 nmol/L (S/N = 3). Method repeatability, precision, and recovery were evaluated and the results were excellent for the efficient HPLC analysis. The most important argument, however, was the high sensitivity and ease-of-handling of the PPIA method. Preliminary experiments with wastewater samples collected from the waterspout of a paper mill and its nearby soil where pollution with aromatic amines may be expected show that the method is highly validated with little interference in the chromatogram.

Global negative vegetation feedback to climate warming responses of leaf litter decomposition rates in cold biomes

Whether climate change will turn cold biomes from large long-term carbon sinks into sources is hotly debated because of the great potential for ecosystem-mediated feedbacks to global climate. Critical are the direction, magnitude and generality of climate responses of plant litter decomposition. Here, we present the first quantitative analysis of the major climate-change-related drivers of litter decomposition rates in cold northern biomes worldwide. Leaf litters collected from the predominant species in 33 global change manipulation experiments in circum-arctic-alpine ecosystems were incubated simultaneously in two contrasting arctic life zones. We demonstrate that longer-term, large-scale changes to leaf litter decomposition will be driven primarily by both direct warming effects and concomitant shifts in plant growth form composition, with a much smaller role for changes in litter quality within species. Specifically, the ongoing warming-induced expansion of shrubs with recalcitrant leaf litter across cold biomes would constitute a negative feedback to global warming. Depending on the strength of other (previously reported) positive feedbacks of shrub expansion on soil carbon turnover, this may partly counteract direct warming enhancement of litter decomposition.

一种新的角加速度估计方法及其应用

首先提出了一种新的基于卡尔曼滤波及牛顿预测的角加速度估计方法,在已知电机驱动系统位置信息的情况下,利用卡尔曼滤波实时估计系统的角加速度;同时采用牛顿预测方法解决估计算法的滞后问题,进一步提高了估计加速度的响应频带．以此为基础,本文进一步分析了利用估计加速度进行反馈控制以增强系统对外扰动的鲁棒性问题,提出了加速度反馈控制策略的设计准则并分析了稳定性．在一个直接驱动机器人关节上针对上述加速度估计及控制方法进行了实验研究:将估计加速度的实验结果与实测加速度(利用加速度计)的实验结果进行了比较分析,从而定量地揭示出估计加速度及其反馈控制在实际系统中的可行性及有效性．

典型人类活动对边坡变形及稳定性的影响研究

China is a mountainous country in which geological hazards occurred frequently, especially in the east of China. Except the geology, topography and extreme climate, the large scale human activities have become a major factor to landslides. Typical human activities which induced landslides are fill, cut and underground mining. On the topic of the deformation mechanism and slope stability, taking three different man-made slopes as examples, deformation mechanism and slope stability were studied by several methods, such as field work, numerical modeling and monitor. The details are as following: (1) The numerical modeling approach advantages over other conventional methods such as limit methods, so the numerical modeling is the major tool in this thesis. So far, there is no uniform failure criterion for numerical simulation. The failure criterion were summarized and analyzed firstly, subsequently the appropriate criterion was determinated. (2) Taking 220kV Yanjin transformation substation fill slope as example, the deformable characteristic, unstable mode and laboratory tests were studied systematically. The results show: the slope deformation was probably caused by a combination effect of unfavorable topographic, geological and hydro geological conditions, and external loading due to filling. It was concluded that the creep deformation of the slope was triggered by external loading applied at the back of the slope. In order to define the calculating parameters, a set of consolidated drained (CD) tests, consolidated undrained (CU) tests, repeated direct shear tests and UCS tests were carried out. The stability of the slope before and after reinforcement was assessed using 3D numerical modeling and shear strength reduction technique. The numerical modeling results showed: the factor of safety (FOS) of the slope was 1.10 in the natural state, and reduced to 1.03 after fill, which was close to the critical state and it caused creeping slip or deformation under rainfall. The failure surface in the slope is in active shear failure, whereas tensile failure occurs at the slope crest. After the site was reinforced with piles, the FOS was 1.27. Therefore, the slope is stable after reinforcement measures were taken. (3) The cut slope stability is a complex problem. Taking the left cut slope of Xiangjiaba as example in this thesis, the deformation and slope stability were studied systematically by numerical modeling and monitor methods. The numerical results show: the displacement is gradually increasing along with the cutting, and the largest displacement is 27.5mm which located at the bench between the elevation 340 and 380. Some failure state units distribute near the undermining part and there is no linked failure state occurred from crest to bottom during cutting. After cutting, some failure units appeared at the ground surface between elevation 340 and 360. The increasing tense stress made the disturbed rock failed. The slope is stable after cutting by the monitor method, such as surface monitor, multipoint displacement meter, inclinometer and anchor cable tensometer. (4) The interaction between underground mining and slope stability is a common situation in mountainous. The slope deformation mechanism induced by underground mining may contributed significantly to slope destabilization. The Mabukan slope in xiangjiaba was analyzed to illustrate this. Failure mechanism and the slope stability were presented by numerical modeling and residual deformation monitor. The results show: the roof deformed to the free face and the floor uplift lightly to the free face. The subsidence basin is formed, but the subsidence and the horizontal movement is small, and there is no failure zone occurred. When the underground mining is going on, the roof deformation, subsidence and the horizontal movements begin increasing. The rock deformation near the free face is larger than the ground surface, and the interaction between these coal seams appeared. There are some tensile failures and shear failures occurred on the roof and floor, and a majority of failure is tensile failure. The roof deformation, subsidence and the horizontal movements increased obviously along with the underground mining. The failure characteristic is shear failure which means the tensile stress transformed to the compressive stress. So the underground mining will induced tensile stress first which lead to structure crack, subsequently the compressive stress appeared which result in slippage. The crest was subjected to horizontal tension which made the rock crack along with the joint. The long term residual deformation monitor demonstrates that the slope is stable after the underground mining stopped.