爆炸引起饱和砂地表沉降的试验研究

通过观察，分析模型试验的现象和结果，讨论了爆炸加密饱和砂的机理，研究了药量与地表下沉量的规律，指出在爆炸加密砂基的问题中比药量不是主要的物理参数。总结出了地表下沉量及爆炸作用范围的计算公式。

Electron Beam Surface Remelting of AISI D2 Cold-Worked Die Steel

Electron beam surface remelting has been carried out on AISI D2 cold-worked die steel. The microstructure and hardening behavior of the electron beam surface remelted AISI D2 cold-worked die steel have been studied by means of optical microscopy and Vickers hardness testing. It was found that AISI D2 steel can be successfully surface hardened by electron beam surface remelting. This surface hardening effect can be attributed to microstructural refinement following electron beam surface remelting. (C) 2002 Elsevier Science B.V. All rights reserved.

Turbulence in laminar premixed V-flames

Strong velocity fluctuations had been found in the laminar premixed V-flames. These velocity fluctuations are closely related to the chemical reaction. But the effects of the upstream combustible mixture velocity on the velocity fluctuations inside the flame are quite weak. The probability distribution function (PDF) of the velocity in the centre region of the flame appears "flat top" shaped. By analyzing the experiment results the flame-flow interactions are found to affect the flame not only at large scale in the flow field but also at small scale inside the flame. These effects will give rise to flame generated small scale turbulences.

清江水库茅坪滑坡监测与发展趋势预测

茅坪滑坡位于清江隔河岩水库上游北岸、距水库坝址66km处。是隔河岩水库库区中最大的基岩古滑坡体，其体积约2．35×10^7m^3。自1993年4月10日水库下闸蓄水以来，该滑坡一直产生缓慢变形。滑坡发生整体失稳，则会截断清江，形成“库中坝”，并造成灾难性的恶果。为此，全面掌握该滑坡的变化发展趋势对今后进行防治决策具有十分重要的意义。掌握滑坡发展变化的关键就是对该滑坡进行现场监测。课题组多次现场踏勘，在原有8个地表监测点的基础上增设了29个监测点，使其布置更科学、合理；并对该滑坡进行了1个水文年的监测工作，获得了大量的笫一手资料，认为该滑坡正处于位移加速阶段。通过现场监测，不仅对滑坡体的现状有了新的认识。同时，预测了茅坪滑坡的变化发展趋势，可以为制定该滑坡的防治预案提供参考。

航天器损伤评估和安全管理中的多尺度力学问题

文章指出航天器的安全性涉及到材料、元件、器件、子系统、系统和整机6个层次.虽然预测和防止失效的任务是在整机层次,但是损伤却是起源于材料的微损伤这一最底层.损伤从原子层次到整机层次的在多个尺度层次上的演化诱致了整体的破坏.由此引入多尺度力学,即研究各种不同长度尺度和时间尺度相互耦合现象的科学.文章试图将力学的宏观运动方程和微结构转变的动力学方程组成统一的方程组,从而得到宏观标量损伤D与微损伤数密度n的关系.文章还指出对于航天器的抗辐射加固问题,微损伤成核和发展的特征时间,与宏观特征空间尺度,以及外加载荷的特

爆轰波在弯管内传播过程数值分析

应用基元反应模型和频散可控耗散格式(DCD)对氢氧爆轰波在弯管内的传播过程进行了数值模拟.计算中氢氧混合物化学反应采用了8种组分20个反应方程式.在处理化学反应引起的刚性问题时采用了时间算子分裂的方法.计算结果表明,在弯管小曲率半径壁面附近,由于膨胀稀疏作用,爆轰波强度减弱,在局部出现前导激波与放热反应区的解藕以及二次起爆现象;在弯管大曲率半径壁面上爆轰波在马赫反射和正规反射之间相互转变,使爆轰波加强.弯管内的爆轰现象与弯管曲率半径有关.

Scheme Construction with Numerical Flux Residual Correction (NFRC) and Group Velocity Control (GVC)

For simulating multi-scale complex flow fields like turbulent flows, the high order accurate schemes are preferred. In this paper, a scheme construction with numerical flux residual correction (NFRC) is presented. Any order accurate difference approximation can be obtained with the NFRC. To improve the resolution of the shock, the constructed schemes are modified with group velocity control (GVC) and weighted group velocity control (WGVC). The method of scheme construction is simple, and it is used to solve practical problems.

自适应光学对大气扰动波前的补偿效果研究：I.理论推导

在采用冻结湍流假设和几何光学近似的条件下，得到了经自适应光学系统校正后的剩余波前相位扰动的结构函数，进而根据剩余相位结构函数与系统Ｓｔｒｅｈｌ比的关系，求出自适应光学系统的补偿效果受系统的时空传递函数，大气湍流，光波传播路径上的横向风，观察目标的旋转角速度以及系统时间延迟影响情况的解析表达式。

含热传导的冲击动力学有限元程序的研究与应用

从有限变形的基本框架出发，建立了含热传导的冲击动力学基本控制方程和合适的初边条件。应用变分原理和伽辽金方法得出了控制方程相应的有限元列式，并探讨了数值计算中的几个关键算法，主要包括构型转换、旋转张量的算法、本构算法以及计算流程和程序框图等。利用自行研制的程序，对长脉冲激光辐照下靶目标的变形和破坏、冲击压缩变形及变形局部化等问题进行了数值模拟和研究，所得结果与实验和理论分析相吻合。

固井工程中的流动问题

同井是油气在建过程中的重要工程，一般分下套管和注水泥两个过程．本文结合作者近年来的研究，着重阐述了钻井液、前置液、水泥浆在环形空间中流动的流体力学问题，包括：高温高压下的水泥浆流变性、偏心环形空间中浆液的流动特性、钻井液-前置液和前置液-水泥浆界面的稳定性等，介绍了国内外学者对这些问题的研究进展，提出了今后应深入研究的问题.

Serrated Plastic Flow in a Zr-Based Bulk Metallic Glass During Nanoindentation

We investigate plastic deformation of Zr41.2Ti13.8Cu12.5Ni10Be22.5 bulk metallic glass using depth sensing nanoindentation. Numerous serrations in the load-displacement curves during indentation, shear bands and pile-ups around the indent were observed. The results revealed that the serrated plastic flow behaviour in this alloy depends strongly on the indentation strain rate.

相对性原理及其对自然界定律的协变性要求：机械能守恒定律协变性疑难的解

阐明狭义相对性原理的准确含义，批出它并不要求自然界每条定律都单独协变，但要求每条定律至少属于一个协变集合，给出最小协变集的求法。表明机械能守恒定律满足狭义相对性原理及其对自然界定律的协变性要求，还指出一切社会科学定律也都满足狭义相对性原理。

Thermal mismatch stress in SiC whisker reinforced aluminium composite: new measurement method by X-ray diffraction

A new X-ray diffraction method for characterising thermal mismatch stress (TMS) in SiC_w–Al composite has been developed. The TMS and thermal mismatch strain (TMSN) in SiC whiskers are considered to be axis symmetrical, and can be calculated by measuring the lattice distortion of the whiskers. Not only the average TMS in whiskers and matrix can be obtained, but the TMS components along longitudinal and radial directions in the SiC whiskers can also be deduced. Experimental results indicate that the TMS in SiC whiskers is compressive, and tensile in the aluminium matrix. The TMS and TMSN components along the longitudinal direction in the SiC whiskers are greater than those along the radial direction for a SiC_w–Al composite quenched at 500°C.

Optical fringe multiplication technique with TEM nano-moiré method

In this paper, a nano-moiré fringe multiplication method is proposed, which can be used to measure nano-deformation of single crystal materials. The lattice structure of Si (111) is recorded on a film at a given magnification under a transmission microscope, which acts as a specimen grating. A parallel grating (binary type) on glass or film is selected as a reference grating. A multiplied nano-moiré fringe pattern can be reproduced in a 4f optical filter system with the specimen grating and the prepared reference grating. The successful results illustrate that this method can be used to measure deformation in nanometre scale. The method is especially useful in the measurement of the inhomogeneous displacement field, and can be utilized to characterize nano-mechanical behaviour of materials such as dislocation and atomic bond failure.