PREDICTION OF VORTEX-INDUCED VIBRATION OF FLEXIBLE RISER USING AN IMPROVED WAKE-OSCILLATOR MODEL

Based on improving the wake-oscillator model, an analytical model for vortex-induced vibration (VIV) of flexible riser under non-uniform current is presented, in which the variation of added mass at lock-in and the nonlinear relationship between amplitude of response and reduced velocity are considered. By means of empirical formula combining iteration computation, the improved analytical model can be conveniently programmed into computer code with simpler and faster computation process than CFD so as to be suitable to application of practical engineering. This model is validated by comparing with experimental result and numerical simulation. Our results show that the improved model can predict VIV response and lock-in region more accurately. At last, illustrative examples are given in which the amplitude of response of flexible riser experiencing VIV under action of non-uniform current is calculated and effects of riser tension and flow distribution along span of riser are explored. It is demonstrated that with the variation of tension and flow distribution, lock-in region of mode behaves in different way, and thus the final response is a synthesis of response of locked modes.

捷安肽素对采后柑桔青绿霉菌抑制效果及作用机理研究

捷安肽素是一种由枯草芽孢杆菌（Bacillus subtilis）ZK 产生的抗真菌多肽。本文以柑桔青霉菌（Penicillium italicum）和绿霉菌（Penicillium digitaum）为供试真菌，研究了捷安肽素的抑菌性能及作用机理，为捷安肽素开发为有效的生物杀菌剂提供理论依据。全文共分两部分：第一部分：捷安肽素对柑桔青霉菌和绿霉菌抑制效果研究。采用琼脂扩散法测定捷安肽素对柑桔青霉菌和绿霉菌的抑菌活性。53.9 µg/mL 捷安肽素对绿霉菌和青霉菌的抑菌圈直径分别为26.7mm 和24.1mm。结果表明捷安肽素能够抑制柑桔青绿霉菌的生长，柑桔绿霉菌比青霉菌对捷安肽素敏感。在柑桔果实上，研究了不同浓度、不同接入时间的捷安肽素对柑桔青霉病和绿霉病的防治效果，并与常用化学杀菌剂抑霉唑、咪鲜胺、甲基硫菌灵和多菌灵作比较。53.9 µg/mL捷安肽素处理柑桔果实，柑桔青霉病和绿霉病发病率分别为5.0 %和5.3 %,比对照低95.0 %和94.7 %；柑桔青霉病和绿霉病的病情指数分别为1.87 和2.18，比对照低73.73 和97.82。结果表明，捷安肽素能够有效地防治柑桔青绿霉病。与对照相比，捷安肽素先于或后于柑桔青绿霉菌接入时，对柑桔青绿霉菌均有抑制作用，但抑制效果随接入间隔时间的增长而降低。第二部分：捷安肽素对绿霉菌作用机理研究。首先在光学显微镜和透射电镜下观察捷安肽素处理后绿霉菌菌丝表面形态结构与菌丝体内超微结构的变化。形态观察发现，捷安肽素处理24h以内，绿霉菌菌丝结构无变化。捷安肽素作用36h后，绿霉菌菌丝不规则缢缩和膨大。48h后，在绿霉菌菌丝顶端、中部、末端的多处细胞均可发生畸形的球状结构，这种畸变结构随处理的延长而增加，致使细胞成为捻珠状。处理72 h后，畸变球形细胞开始断裂离解。处理96h后，镜下几乎无完整菌丝，成单个的球状细胞，部分细胞出现破裂。而对照菌丝表面光滑，结构完整。通过透射电镜观察发现，与对照相比，捷安肽素处理后，绿霉菌细胞壁、细胞膜轮廓模糊不清，细胞质外泄。推测捷安肽素能够使绿霉菌细胞膜通透性发生改变。进一步实验利用紫外-可见分光光度计检测捷安肽素作用后绿霉菌胞外液紫外吸光度的变化，表明捷安肽素作用于绿霉菌菌丝后，细胞内蛋白质、核酸缓慢泄漏。通过Atomscan Advantage单道扫描等离子体发射光谱仪(ICP)测定捷安肽素作用后菌丝体内K+浓度的改变，结果表明捷安肽素作用于柑桔绿霉菌1h内，菌丝体内K+含量迅速下降，为对照绿霉菌K+含量的37.53 %，1 h后菌丝体内K+含量变化趋于平缓。K+的迅速泄漏，以及蛋白质、核酸的泄漏表明捷安肽素通过迅速改变绿霉菌细胞膜通透性，使绿霉菌菌丝生长受到抑制。Jiean-peptide produced by Bacillus subtilis ZK has broad-spectrumresistance to plant pathogens. In this study, we investigated the antifungal propertyand the possible antifungal mechanism of jiean-peptide against two commonphytopathogenic fungi of citrus fruits: blue molds (P. italicum) and green molds (P.digitatum).The paper involved two parts:Part 1 is the study of the antifungal property of jiean-peptide against blue moldsand green molds of citrus fruits. The in vitro inhibition effect of jiean-peptide againstblue molds and green molds was detected by agar diffusion method. The diameters ofinhibition zones of green molds and blue molds are 26.7mm and 24.1mm respectivelyby treating with 53.9 µg/mL jiean-peptide. It shows that jiean-peptide effectivelyinhibits the both phytopathogenic fungi, and it is more effective for inhibiting greenmolds than blue molds. The effectiveness of jiean-peptde to inhibit green molds andblue molds in vivo was investigated compared with four conventional fungicides thatare imazalil, prochloraz, carbendazin and methylthiophanate. The result is that the incidences of the blue mold disease and green mold disease are 5.0 % and 5.3 %, thedisease severities are 1.87 and 2.18 respectively when citrus are inoculated with 53.9µg/ml jiean-peptide. The decay incidences and disease severities were significantlyreduced by treating with jiean-peptide compared with the control. The results indicateJiean-peptide is effective for controlling blue molds and green molds on citrus. Theoptimized inoculation time was also investigated. When inoculated with jiean-peptideat 0 h, 6 h, 12 h, 24 h and 48 h before or after pathogens’ inoculation, Jiean-peptidecan suppress the occurrence of blue molds and green molds compared with the control, but the effect of later inoculation decreases compared with the inoculation at the sametime.In Part 2, we investigated the possible antifungal mechanism against greenmolds of citrus. At first, we observed the exterior morphological changes andultrastructural changes of blue molds under light microscopy (LM) and transmissionelectron microscopy (TEM). Compared with untreated control cells which aregenerally uniform in shape, the appearances of treated hyphae change obviously. Itshows that some cells of hyphae irregularly shrink or enlarge when cultured for 36h.When the treating time of jiean-peptide increases, the aberrance of the hyphaebecomes more obvious, and hyphae exhibit the moniliform appearances. Finally, thereis no intact hypha leaved except only single cells, and some of which appear fractured.By transmission electron microscopy (TEM) observation, we find that the outline ofthe cell wall and the cell membrane of hyphae are blurry, and the cytoplasma oozesout. The observation result under LM and TEM suggests that jiean-peptide mightchange the permeability of the cell membrane. So we conducted further experiment todetect the change of permeability when the cells of blue molds were treated withjiean-peptide. And the effect of jiean-peptide on non-growing cells of blue molds wastested. By the spectrophotometer measurement, we found that compounds with lightabsorption at 260 nm and 280 nm were released and amounts increased within 12 hcompared with the control. Moreover, by the ICP measurement, the leakage of K+occurred immediately in the presence of jiean-peptide within 1 h, but with nearly nofurther change after 1 h. All these results indicate that jiean-peptide could change themembrane permeability of blue molds immediately and result in leaking nucleotides,proteins and K+ from cells.

Pre-irradiation with low-dose C-12(6+) beam significantly enhances the efficacy of AdCMV-p53 gene therapy in human non-small lung cancer

The combination of ionizing radiation and gene therapy has been investigated. However, there are very few reports about the combination of heavy-ion irradiation and gene therapy. To determine if the pre-exposure to low-dose heavy ion beam enhances the suppression of AdCMV-p53 on non-small lung cancer (NSLC), the cells pre-irradiated or non-irradiated were infected with 20, 40 MOI of AdCMV-p53. Survival fraction and the relative biology effect (RBE) were determined by clonogenic assay. The results showed that the proportions of p53 positive cells in C-12(6+) beam induced AdCMV-p53 infected cells were more than 90%, which were significantly more than those in gamma-ray induced AdCMV-p53 infected cells. The pre-exposure to low-dose 12C6+ beam significantly prevented the G(0)/G(1) arrest and activated G(2)/M checkpoints. The pre-exposure to C-12(6+) beam significantly improved cell to apoptosis. RBEs for the C-12(6+)+ AdCMV-p53 infection groups were 30%-60%,20% -130% and 30%-70% more than those for the C-12(6+)_irradiated only, AdCMV-p53 infected only, and gamma-irradiation induced AdCMVp53 infected groups, respectively. The data suggested that the pre-exposure to low-dose C-12(6+) beam significantly promotes exogenous p53 expression in NSLC, and the suppression of AdCMV-p53 gene therapy on NSLC.

玉米冠层对喷灌水量的再分配

通过喷灌玉米田间试验,研究了喷灌水经玉米冠层再分配后的分布状况。结果表明:在玉米全生育期,茎秆下流水量占灌水量的均值为44%左右,棵间穿透水量占灌水量的均值为48%左右,冠层截留量在0.8￣2.9mm之间变化。一次灌水中,喷灌水在地表的分布很不均匀,43.2%的灌水量经茎秆下流到根区,在距离茎秆7cm,15cm,25cm和32.5cm处,地表接收的水量占总灌水量的比例分别为18.9%、43.5%、66.9%和84.5%。灌水量、种植密度、株高和叶面积指数等都影响着喷灌水在地表的分布。

Effect of ancillary ligands on the properties of heteroleptic green iridium dendrimers functionalized with carbazole dendrons

A series of heteroleptic green iridium dendrimers functionalized with carbazole dendrons, such as G2(pic) and G2(acac), have been synthesized, in which picolinic acid and acetylacetone are used as the ancillary ligands, respectively. Compared with the corresponding homoleptic iridium dendrimer G2 (8%), these heteroleptic ones can be prepared under mild conditions with total yields as high as 55-67%. Both the dendrimer G2(pic) and G2(acac) display bright green emissions with photoluminescence quantum yields higher than 0.80 in toluene solution. As a result, a maximum external quantum efficiency of 7.1% (21.0 cd/A) for G2(pic) and 7.7% (25.8 cd/A) for G2(acac) has been realized based on non-doped device configuration. The state-of-art performance indicates that the heteroleptic dendrimers can be promising candidates used for non-doped electrophosphorescent devices, especially when the ease of synthesis in a large scale is considered.

Evaluation of ferricyanide effects on microorganisms with multi-methods

In this study, we report the effects of ferricyanide on organisms based on the changes in physiological state and morphology of Escherichia coli (E coli) DH 5 alpha after being pretreated by ferricyanide. The impact on bacterial cell growth and viable rate of exposure to different concentrations of ferricyanide was determined, and the morphology change of E. coli was studied by atomic force microscopy (AFM). Finally, recovery test was used to evaluate the recovery ability of injured cells. The results showed that the effects on growth and morphology of E. coli were negligible when the concentration of ferricyanide was below 25.0 mM. While the results showed 50.8% inhibition of growth in the presence of 50.0 mM ferricyanide for 3 h, 89.6% viability was detected by flow cytometry (FCM) assay. AFM images proved that compact patches appeared on the bacterial surface and protected the bacterial viability. Furthermore, the results revealed that deterioration of bacterial surface closely related to the incubation time from 0.5 to 3 h at 100.0 mM ferricyanide. In the recovery test, microbial cell population and dissolved oxygen individually decreased 36.7% and 28.3% with 25.0 mM ferricyanide.

Direct oxidation of benzene to phenol on manganese pyrophosphate with hydrogen peroxide

A solid catalyst manganese pyrophosphate based on non-sieves to oxidize benzene to phenol with oxidant hydrogen peroxide has shown good conversion with good selectivity in CH3CN at 65 degrees C investigating water contact angle data of three manganese salts, it is found manganese pyrophosphate has certain repulsive water character. It is further to be confirmed by benzene and phenol adsorption experiments onto catalyst surface by GC. With benzene/H2O2 ratio of 1, the benzene conversion of 13.8% with phenol selectivity of 85.0% was achieved. It is noteworthy that no any products are obtained using manganese pyrophosphate as catalyst in the oxidation of phenol in CH3CN solvent.

Characterization and properties of the neutral and doped blends of poly(3-dodecylthiophene) with low-density polyethylene

In this paper, the structures and properties of the neutral and doped blends of poly(3-dodecylthiophene) (P3DDT) with low-density polyethylene (LDPE) were investigated. Wide-angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), Fourier transform infrared spectra (FTIR), and scanning electron microscopy (SEM) were used to characterize the structures and morphologies of the blends, and conductivity was also measured. It was found that separate crystallizations occur between P3DDT and LDPE. When the amount of P3DDT is small in the blend, it has the effect of a nucleation reagent and has some influence on the crystal structure. After doping, the interaction force between the molecular chains increases, and leads to a more compact packing and a more uniform dispersion in morphology. Through blending, the thermal stability of pure component could be greatly improved, especially when the P3DDT content is 5 wt %. The conductivity measurements indicate that the conductivity increases with the increase of the P3DDT composition and doping time.

基于介电泳的电极阵列电场仿真研究

介电泳方法被广泛地应用于微纳颗粒的分离和操纵中,实现介电泳操作的关键是设计满足所需电场分布的电极阵列。针对目前在微电极阵列设计中尚缺乏简单有效的电场解析方法的现状,提出一种基于格林公式的电极阵列电场的解析方法。首先介绍了传统介电泳和行波介电泳的概念和计算模型,分析了介电泳过程与电极上所施加的交变电压的频率和幅度的关系,然后在确立电极电势的边界条件的基础上,采用基于格林公式的电场解析方法,建立了非均匀电场的解析模型,得出不同条件下的电极阵列电场分布的仿真结果,最后利用FEMLAB有限元仿真软件对解析模型进行了对比仿真,验证了该解析模型的可行性。基于格林公式的电场解析求解方法能够有效地提高电极阵列设计中的针对性以及缩短电极设计的时间。

消除采集脚印的处理方法研究

Seismic technique is in the leading position for discovering oil and gas trap and searching for reserves throughout the course of oil and gas exploration. It needs high quality of seismic processed data, not only required exact spatial position, but also the true information of amplitude and AVO attribute and velocity. Acquisition footprint has an impact on highly precision and best quality of imaging and analysis of AVO attribute and velocity. Acquisition footprint is a new conception of describing seismic noise in 3-D exploration. It is not easy to understand the acquisition footprint. This paper begins with forward modeling seismic data from the simple sound wave model, then processes it and discusses the cause for producing the acquisition footprint. It agreed that the recording geometry is the main cause which leads to the distribution asymmetry of coverage and offset and azimuth in different grid cells. It summarizes the characters and description methods and analysis acquisition footprint’s influence on data geology interpretation and the analysis of seismic attribute and velocity. The data reconstruct based on Fourier transform is the main method at present for non uniform data interpolation and extrapolate, but this method always is an inverse problem with bad condition. Tikhonov regularization strategy which includes a priori information on class of solution in search can reduce the computation difficulty duo to discrete kernel condition disadvantage and scarcity of the number of observations. The method is quiet statistical, which does not require the selection of regularization parameter; and hence it has appropriate inversion coefficient. The result of programming and tentat-ive calculation verifies the acquisition footprint can be removed through prestack data reconstruct. This paper applies migration to the processing method of removing the acquisition footprint. The fundamental principle and algorithms are surveyed, seismic traces are weighted according to the area which occupied by seismic trace in different source-receiver distances. Adopting grid method in stead of accounting the area of Voroni map can reduce difficulty of calculation the weight. The result of processing the model data and actual seismic demonstrate, incorporating a weighting scheme based on the relative area that is associated with each input trace with respect to its neighbors acts to minimize the artifacts caused by irregular acquisition geometry.

南海北部陆缘深水区构造－热演化与烃源岩成熟度史研究

Abstract In order to provide basic data for evaluation of the petroleum potential in the deep water area of the northern margin of the South China Sea (SCS), present-day thermal regime and basin tectonothermal evolution are reconstructed and the maturation history of the Cenozoic major source rocks in the study area is derived. The present-day geothermal regime in the deep water area of the northern margin of SCS is defined according to the geothermal gradient, thermal properties and heat flow data. Tectonic subsidence history is reconstructed based on borehole and seismic data, and accordingly the stretching episodes are determined from the subsidence pattern. Heat flow history in the deep water area of the northern margin of SCS is estimated on a finite time, laterally non-uniform and multi-episode stretching model. Maturation history of the main source rocks in the study area is estimated through EASYRo% kinetic model and thermal history, and the potential of petroleum in the deep water area of the northern margin of SCS is evaluated based on the data above. The results show that the present-day geothermal regime in the deep water area of the northern margin of SCS is characterized by “hot basin” with high geothermal gradient (39.1±7.4℃/km) and high heat flow (77.5±14.8 mW/m2), and that the Qiongdongnan Basin (QDNB) underwent three stretching episodes and consequently suffered three heating episodes (Eocene, Oligocene and Pliocene time) with highest paleo-heat flow of 65～90 mW/m2 at the end of the Pliocene, that the Pearl River Mouth Basin (PRMB) two stretching and two heating episodes (Eocene, Oligocene time) with highest paleo-heat flow of 60～70 mW/m2 at the end of the Oligocene, and that the source rocks matured drastically responding to the heating episodes. There are four hydrocarbon generation kitchens in the deep water area of the northern margin of SCS which are favor of its bright petroleum perspective. Tectonothermal analysis indicates that the present-day geothermal regime which is characterized with “hot basin” in the deep water area of the PRMB resulted mainly from the Cenozoic stretching as well as faulting and magmatic activities during the Neotectonic period, and that the Pliocene heating episode of the QDNB is coupled with the transition from sinistral to dextral gliding of the Red Rive fault, and that the deep water basins in the northern margin of SCS are typical of multiple rifting which caused multi-episode heating process.

接收函数方法与中国及邻区上地幔间断面的研究

The receiver function method applied in researching the discontinuities in upper mantle was systematically studied in this paper. Using the theoretical receiver functions, the characteristics of P410S and P660S phases were analyzed, and the influencing factors for detection of these phases were discussed. The stability of receiver function was studied, and a new computational method of receiver function, RFSSMS (Receiver Function of Stack and Smooth of Multi seismic-records at a Single station), was put forward. We built initial reference velocity model for the media beneath each of 18 seismic stations respectively; then estimated the buried depths of 410-km and 660-km discontinuities(simply marked as '410' and '660') under the stations by using the arrive time differences of P410S and P660S with P. We developed a new receiver function inversion method -PGARFI (Peeling-Genetic Algorithm of Receiver Function Inversion), to obtain the whole crust and upper mantle velocity structure and the depths of discontinuities beneath a station. The major works and results could be summarized as follows: (1) By analysis of the theoretical receiver functions with different velocity models and different ray parameters, we obtain the knowledge: The amplitudes of P410S and P660S phases are decreasing with the increasing of epicentral distance A , and the arrival time differences of these phases with P are shorter as A is longer. The multiple refracted and/or reflected waves yielded on Moho and the discontinuities in the crust interfere the identification of P410S. If existing LVZ under the lithosphere, some multiple waves caused by LVZ will interfere the identification of P410S. The multiple waves produced by discontinuity lied near 120km depth will mix with P410s phase in some range of epicentral distance; and the multiple waves concerned with the discontinuity lied near 210km depth will interfere the identification of P660S. The epicentral distance for P4i0s identification is limited, the upper limit is 80° . The identification of P660S is not restricted by the epicenter distance obviously. The identification of P410S and P6gos in the theoretical receiver functions is interfered weakly from the seismic wave attenuation caused by the media absorption if the Q value in a reasonable range. (2) The stability of receiver function was studied by using synthetic seismograms with different kind of noise. The results show that on the condition of high signal-noise-ratio of seismic records, the high frequency background noise and the low frequency microseism noise do not influence the calculating result of receiver function. But the media "scattering noise" influence the stability of receiver function. When the scattering effect reach some level, the identification of P4iOs and P66os is difficult in single receiver function which is yielded from only one seismic record. We provided a new method to calculate receiver function, that is, with a group of earthquake records, stacking the R and Z components respectively in the frequency domain, and weighted smooth the stacked Z component, then compute the complex spectrum ratio of R to Z. This method can improve the stability of receiver function and protrude the P4i0s and P66os in the receiver function curves. (3) 263 receiver functions were provided from 1364 three component broadband seismograms recorded at 18 stations in China and adjacent areas for the tele-earthquakes. The observed arrival time differences of P410S and P660S with P were obtained in these receiver functions. The initial velocity model for every station was built according to the prior research results. The buried depths of '410' and '660' under a station were acquired by the way of adjusting the depths of these two discontinuities in the initial velocity model until the theoretical arrival time differences of P410S and P660S with P well conformed to the observed. The results show an obvious lateral heterogeneity of buried depths of ' 410' and (660' . The depth of '410' is shallower beneath BJI, XAN, LZH and ENH, but deeper under QIZ and CHTO, and the average is 403km . The average depth of '660' is 663km, deeper under MDJ and MAJO, but shallower under QIZ and HYB. (4) For inversing the whole crust and upper mantle velocity structure, a new inversion method -PGARFI (Peeling-Genetic Algorithm of Receiver Function Inversion) has- been developed here. The media beneath a station is divided into segments, then the velocity structure is inversed from receiver function from surface to deep successively. Using PGARFI, the multi reflection / refraction phases of shallower discontinuities are isolated from the first order refraction transform phase of deep discontinuity. The genetic algorithm with floating-point coding was used hi the inversion of every segment, and arithmetical crossover and non-uniform mutation technologies were employed in the genetic optimization. 10 independent inversions are completed for every segment, and 50 most excellent velocity models are selected according to the priority of fitness from all models produced in the inversion process. The final velocity structure of every segment is obtained from the weighted average of these 50 models. Before inversion, a wide range of velocity variation with depth and depth range of the main discontinuities are given according to priori knowledge. PGARFI was verified with numerical test and applied in the inversion of the velocity structure beneath HIA station down to 700km depth.