One-Dimensional InP-Based Photonic Crystal Quantum Cascade Laser Emitting at 5.36μm

An InP-based one-dimensional photonic crystal quantum cascade laser is realized. With photo lithography instead of electron beam lithography and using inductively coupled plasma etching, four-period air-semiconductor couples are defined as Bragg reflectors at one end of the resonator. The spectral measurement at 80K shows the quasi-continuous-wave operation with the wavelength of 5.36μm for a 22μm-wide and 2mm-long epilayer-up bonded device.

Application of step-scan FTIR to the research of quantum cascade lasers

The principle of step-scan Fourier transform infrared （FTIR） spectroscopy is introduced. Double modulation step-scan FTIR technique is used to obtain the quantum cascade laser＇s stacked emission spectra in the time domain. Optical property and thermal accumulation of devices due to large drive current are analyzed.

Room Temperature Operation of Strain-Compensated 5.5μm Quantum Cascade Lasers

Room temperature operation is an important criterion for high performance of quantum cascade lasers. A strain-compensated quantum cascade laser（λ≈5.5μm） with optimized waveguide structure lasing at room temperature is reported. Accurate control of layer thickness and strain-compensated material composition is demonstrated using X-ray diffraction. An output power of at least 45mW per facet is realized for a 20μm-wide and 2mm-long laser at room temperature.

Diffractive microlens with a cascade focal plane fabricated by single mask UV-photolithography and common KOH:H2O etching

A diffractive microlens with a cascade focal plane along the main optical axis of the device is fabricated using a low-cost technique mainly including single mask ultraviolet (UV) photolithography and dual-step KOH:H2O etching. Based on the evolutionary behavior of converse pyramid-shaped microholes (CPSMs) preshaped over a {100}-oriented silicon wafer in KOH etchant, the first-step KOH etching is performed to transfer initial square micro-openings in a SiO2 film grown by plasma enhanced chemical vapor deposition (PECVD) and patterned by single mask UV-photolithography, into CPSMs with needed dimension. After completely removing a thinned SiO2 mask, basic annular phase steps with a relatively steep sidewall and scheduled height can be shaped in the overlapped etching region between the neighboring silicon concave-arc microstructures evolved from CPSMs through the second-step KOH etching. Morphological measurements demonstrate a desirable surface of the silicon microlens with a roughness in nanometer scale and the feature height of the phase steps formed in the submicrometer range. Conventional optics measurements of the plastic diffractive microlens obtained by further hot embossing the fine microrelief phase map over the nickel mask made through a common electrochemical method indicate a highly efficient cascaded focusing performance.

Terahertz Quantum Cascade Laser Operating at 2.94 THz

The development of quantum cascade laser at 2.94 THz is reported. The laser structure is based on a bound-to-continuum active region and a semi-insulating surface-plasmon waveguide. Lasing is observed up to a heat-sink temperature of 70 K in pulsed mode with light power of 4.75 mW at 10 K and 1 mW at 70 K. A threshold current density of 296.5 A/cm(2) and an internal quantum efficiency of 1.57 x 10(-2) per cascade period are also observed at 10 K. The characteristic temperature of this laser is extracted to be T-0 = 57.5 K.

Surface Emitting Distributed Feedback Quantum Cascade Laser around 8.3 mu m

We demonstrate surface emitting distributed feedback quantum cascade lasers emitting at wavelengths from 8.1 mu m at 90 K to 8.4 mu m at 210 K. The second-order metalized grating is carefully designed using a modified coupled-mode theory and fabricated by contact lithography. The devices show single mode behavior with a side mode suppression ratio above 18 dB at all working temperatures. At 90 K, the device emits an optical power of 101 mW from the surface and 199 mW from the edge. In addition, a double-lobe far-field pattern with a separation of 2.2 degrees is obtained in the direction along the waveguide.

Seeding nets with neutral spores of the red alga Porphyra umbilicalis (L.) Kutzing for use in integrated multi-trophic aquaculture (IMTA)

Nets in traditional Porphyra mariculture are seeded with conchospores derived from the conchocelis phase, and spend a nursery period in culture tanks or calm coastal waters until they reach several centimeters in length. Some species of Porphyra can regenerate the foliose phase directly through asexual reproduction, which suggests that the time, infrastructure, and costs associated with conchocelis culture might be avoided by seeding nets with asexual spores. Here, we present work from a short-term mariculture study using nets seeded with asexual spores (neutral spores) of a native Maine species of Porphyra. Porphyra umbilicalis (L.) Kutzing was selected for this proof of concept research because of its reproductive biology, abundance across seasons in Maine, and evidence of its promise as a mariculture crop. We studied the maturation, release, and germination of the neutral spores to develop an appropriate seeding protocol for nets, followed by development of a nursery raceway to provide an easily manipulated environment for the seeded nets. Neutral spores were produced throughout the year on the central Maine coast,however, there was a temporal variability in the number and survival of released neutral spores, depending upon thallus position in the intertidal zone. Small thalli were strictly vegetative, but most thalli reproduced by neutral spores- sexual reproduction was absent. Neutral spores germinated quickly at 10 and 15 'C, but germination was delayed at 5 degrees C. Unlike some algal zygotes and spores, neutral spores of R umbilicalis required light to germinate; however, irradiances of 25 and 100 mu mol photons M-2 S-1 were equally sufficient for germination. Rafts of seeded nets were deployed in Cobscook Bay, Maine, at two distances from salmon aquaculture pens and at a control site on a nearby, fallow aquaculture site (no salmon). There was no difference in nitrogen content of harvested thalli; however, both the density and the surface area of harvested thalli were different among the sites. The possible causes of these differences are discussed in the context of potential use of P umbilicalis in IMTA. (C) 2007 Elsevier B.V. All rights reserved.

Potential of the seaweed Gracilaria lemaneiformis for integrated multi-trophic aquaculture with scallop Chlamys farreri in North China

In this study the red alga, Gracilaria lemaneiformis, was cultivated with the scallop Chlamys farreri in an integrated multi-trophic aquaculture (IMTA) system for 3 weeks at the Marine Aquaculture Laboratory of the Institute of Oceanology, Chinese Academy of Sciences (IOCAS) in Qingdao, Shandong Province, North China. The nutrient uptake rate and nutrient reduction efficiency of ammonium and phosphorus from scallop excretion were determined. The experiment included four treatments each with three replicates, and three scallop monoculture systems served as the control. Scallop density (407.9 +/- 2.84 g m(-3)) remained the same in all treatments while seaweed density differed. The seaweed density was set at four levels (treatments 1, 2, 3, 4) with thallus wet weight of 69.3 +/- 3.21, 139.1 +/- 3.80, 263.5 +/- 6.83, and 347.6 +/- 6.30 g m(-3), respectively. There were no significant differences in the initial nitrogen and phosphorus concentration between each treatment and the control group (ANOVA, p > 0.05). The results showed that at the end of the experiment, the nitrogen concentration in the control group and treatment 1 was significantly higher than in the other treatments. There was also a significant difference in phosphorus concentration between the control group and the IMTA treatments (ANOVA, p < 0.05). Growth rate, C and N content of the thallus, and mortality of scallop was different between the IMTA treatments. The nutrient uptake rate and nutrient reduction efficiency of ammonium and phosphorus changed with different cultivation density and time. The maximum reduction efficiency of ammonium and phosphorus was 83.7% and 70.4%, respectively. The maximum uptake rate of ammonium and phosphorus was 6.3 and 3.3 A mu mol g(-1) DW h(-1). A bivalve/seaweed biomass ratio from 1:0.33 to 1:0.80 (treatments 2, 3, and 4) was preferable for efficient nutrient uptake and for maintaining lower nutrient levels. Results indicate that G. lemaneiformis can efficiently absorb the ammonium and phosphorus from scallop excretion and is a suitable candidate for IMTA.

Modeling trophic positions of the alpine meadow ecosystem combining stable carbon and nitrogen isotope ratios

Stable carbon and nitrogen isotope ratios of single tissues or whole bodies were analyzed to establish trophic positions of main consumers living at the alpine meadow ecosystem in the Tibetan Plateau. The results demonstrated that delta C-13 and delta N-15 values of vertebrates showed great variations and ranged from -26.83 to -22.51 parts per thousand and from 2.33 to 8.44 parts per thousand, respectively. Plateau pika, root vole, plateau hare, infants of rodents and hatchlings of passerine bird species had the lowest delta C-13 and delta N-15 values. delta C-13 and delta N-15 values of omnivorous and insectivorous birds and amphibians showed intermediate. Carnivorous species, steppe polecat and Upland buzzard, and omnivorous Robin accentor and White wagtail possessed extremely higher VC and delta N-15 values. Omnivorous birds captured in earlier year had significantly less negative delta C-13 and greater delta N-15 values than those captured later. Based on steady angular enrichment between trophic levels, an "alpha and vector model" combing delta C-13 and delta N-15 values was introduced to reveal trophic positions, the results indicated that Tibetan sheep, Tibetan yak, plateau pika, root vole, plateau hare, infants of small rodents showed the lowest trophic positions (TP 1.81-2.38). While omnivorous and insectivorous birds, their hatchlings and amphibians showed intermediate trophic positions (TP 2.06-2.89), carnivorous species steppe polecat and Upland buzzard, migrant birds possessed extremely higher trophic positions (TP 2.89-3.05). The isotopic investigation of organisms and the introduced "alpha and vector model" successfully demonstrated the same trophic positions and diet prediction of consumers as nitrogen enrichment model at the alpine meadow ecosystem. Besides of this information, the "alpha and vector model" can also be incorporated into multiple isotope signatures to infer trophic relationships. This angular enrichment model has the potential to address basic ecological questions, such as trophic structure, trophic dynamics, and energy flow in other terrestrial ecosystems of properly handled. (C) 2005 Elsevier B.V. All rights reserved.

Fractals and Scaling in Fracture Induced by Microcrack Coalescence

A numerical model is proposed to simulate fracture induced by the coalescence of numerous microcracks, in which the condition for coalescence between two randomly nucleated microcracks is determined in terms of a load-sharing principle. The results of the simulation show that, as the number density of nucleated microcracks increases, stochastic coalescence first occurs followed by a small fluctuation, and finally a newly nucleated microcrack triggers a cascade coalescence of microcracks resulting in catastrophic failure. The fracture profiles exhibit self-affine fractal characteristics with a universal roughness exponent, but the critical damage threshold is sensitive to details of the model. The spatiotemporal distribution of nucleated microcracks in the vicinity of critical failure follows a power-law behaviour, which implies that the microcrack system may evolve to a critical state.

Catastrophic Rupture Induced Damage Coalescence in Heterogeneous Brittle Media

In heterogeneous brittle media, the evolution of damage is strongly influenced by the multiscale coupling effect. To better understand this effect, we perform a detailed investigation of the damage evolution, with particular attention focused on the catastrophe transition. We use an adaptive multiscale finite-element model (MFEM) to simulate the damage evolution and the catastrophic failure of heterogeneous brittle media. Both plane stress and plane strain cases are investigated for a heterogeneous medium whose initial shear strength follows the Weibull distribution. Damage is induced through the application of the Coulomb failure criterion to each element, and the element mesh is refined where the failure criterion is met. We found that as damage accumulates, there is a stronger and stronger nonlinear increase in stress and the stress redistribution distance. The coupling of the dynamic stress redistribution and the heterogeneity at different scales result in an inverse cascade of damage cluster size, which represents rapid coalescence of damage at the catastrophe transition.