侧面抽运国产Nd∶YAG陶瓷棒的激光特性

实验研究了激光二极管阵列(LDA)侧向抽运国产Nd∶YAG陶瓷棒的准连续及被动调Q激光输出特性。该陶瓷激光器采用LDA侧面紧密环绕均匀排布的抽运结构,陶瓷棒抽运区域长度为20 mm,其总尺寸为3 mm×35 mm,掺杂原子数分数为~1%。在千赫兹准连续运转条件下,当平-平谐振腔的输出耦合镜透过率为47.3%时,获得最大平均功率23 W的1064 nm激光输出,光束发散角为4.5 mrad,斜率效率达12%。在谐振腔内插入Cr4+∶YAG晶体作为被动调Q开关,成功地实现了陶瓷激光器千赫兹重复频率调Q激光脉冲输出,当Cr4+∶YAG晶体初始透过率为60%时,输出激光脉冲宽度(半峰全宽)可窄至14.5 ns,调Q动静比约为40%。

种子光功率对脉冲双包层光纤放大器性能的影响

采用国产的大模场面积双包层光纤和(2+1)×1多模泵浦耦合器，研制出近衍射极限输出的MOPA式脉冲光纤放大器。基于该放大器，发现种子光输出平均功率对放大性能有一定的影响。在泵浦功率一定的情况下，为保证脉冲光纤放大器稳定可靠地运行，对种子光功率来讲，存在一个特定的取值范围。种子光输出平均功率70 mW时，对该脉冲光纤放大器的放大性能进行了研究。

基于RS编码及网格编码调制的光PPM通信纠错技术

分析了RS（Reed-Solomon）纠错码和网格编码调制（Trellis Coded Modulation，TCM）技术在光脉冲位置调制通信中的应用．在此基础上，提出了以RS码作为外码，以网格编码调制技术作为内码，用于光脉冲位置调制通信的新编码方案，能以几乎不减少通信速率的优势，提高传统RS码系统在时变带限光信道中的通信性能．模拟研究了在不同空间光信道条件下，传统RS码的符号正确传输率和误码率，并对网格编码调制的编码增益、RS码与网格编码调制级联时的编码增益进行了仿真研究，证实了本方案的有效性．

20-W average power, high repetition rate, nanosecond pulse with diffraction limit from an all-fiber MOPA system

In this article, we report an all-fiber master oscillator power amplifier (MOPA) system, which can provide high repetition rate and nanosecond pulse with diffraction-limit. The system was constructed using a (2 + 1) X 1 multimode combiner. The Q-Switched, LD pumped Nd:YVO4 solid-state laser wets used (is master oscillator. The 976-nm fiber-coupled module is used as pump source. A 10-m long China-made Yb3+-doped D-shape double-clad large-mode-area fiber was used as amplifier fiber. The MOPA produced as much as 20-W average power with nanosecond pulse and near diffraction limited. The pulse duration is maintained at about 15 its during 50-175 kHz. The system employs a simple and compact architecture and is therefore suitable for the use in practical applications such as scientific and military airborne LIDAR and imaging. Based oil this system. the amplification performances of. the all fiber amplifier is investigated. (C) 2008 Wiley Periodicals, Inc.

新型掺铒离子氧氟碲酸盐玻璃的光谱性质

探求新的具有优良的热学和光学性能的基质玻璃系统，是获得具有宽带宽和增益平坦的掺Er^3＋光纤放大器（EDFA）的一种有效途径。制备了一种新型氧氟碲酸盐玻璃TeO2-BaF2-LaF3，并对其热学性能和光学性质进行了测试。应用乍得-奥菲尔特（Judd-Ofelt）理论计算了Er^3＋离子的J-O理论参量和荧光寿命r。探讨了氟化物的引入对碲酸盐玻璃结构的改变的影响，并分析了其对玻璃的热学性质和光学性质的影响。实验发现，获得的氧氟碲酸盐玻璃具有优良的热学稳定性（△T=156.6C），宽的荧光半峰全宽（72nm）

基于上转换发光技术的生物传感器及其应用

为实现对特定生物分子的高灵敏度快速检测与分析。采用上转换发光材料作为标记物，研制成功一台基于上转换发光技术的新型光学免疫生物传感器。该传感器利用上转换发光材料在红外光激发下发射可见磷光的特性，通过对免疫层析试纸条上经生物反应而结合上去的上转换发光材料颗粒的含量进行检测，计算出被测样品中特定生物分子的浓度。实验结果表明，该传感器具有较好的生物特异性，对兔抗鼠疫免疫球蛋白(IgG)标准样品的检测灵敏度达到ng／ml量级，并在200～6000ng／ml浓度范围内具有良好的线性响应特性，相关系数R^2≥0．95；

Sites structure and spectroscopic properties of Yb-doped and Yb, Na-codoped CaF2 laser crystals

For the first time, the effect of Na+ on crystal structure, valence state of Yb ions, spectroscopic properties of YbF3-doped CaF2 system was systematically studied. Na+ can greatly suppress the deoxidization of Yb3+ to Yb2+. Absorption and emission spectra showed codoping Na+ with different Na:Yb ratios can modulate the spectroscopy and photoluminescence properties of Yb3+ ions in CaF2 lattice in a large scope. The emission lifetime and quantum efficiency of Yb3+ in CaF2 were greatly enhanced by the codopant of Na+. The potential laser performances of the new Yb, Na-codoped CaF2 crystals were predicted. (c) 2005 Elsevier B.V. All rights reserved.

背投显示技术及其用光学薄膜

对比了背投领域几种主要技术的原理和性能特点，同时介绍了多媒体投影系统所需要的各类光学薄膜的作用，参数和光学性能；并针对该领域国内外最新研究状况进行了调研，给出了现在所面临的关键技术难题并对其发展前景做了预测。

Control of polarization for a broadband dichroic filter at 45 degrees incidence

A method for the control of polarization for a broadband dichroic filter was reported and some design examples were elaborated. This method could be applied over a wide range of wavelengths and a wide range of polarizations in the transmission region. A nonpolaiizing broadband dichroic filter and a broadband dichroic filter with certain polarization were designed and fabricated by electron beam evaporation with ion beam assisted deposition. The experimental spectral performances showed good agreement with their theoretical curves. In addition, the application of the method was discussed. (c) 2007 Optical Society of America

Optimization of thin-film design for multi-layer dielectric grating

Thin-film design used to fabricate multi-layer dielectric (MLD) gratings should provide high transmittance during holography exposure, high reflectance at use wavelength and sufficient manufacturing latitude of the grating design making the MLD grating achieve both high diffraction efficiency and low electric field enhancement. Based on a (HLL)H-9 design comprising of quarter-waves of high-index material and half-waves of low-index material, we obtain an optimum MLD coating meeting these requirements by inserting a matching layer being half a quarter-wave of Al2O3 between the initial design and an optimized HfO2 top layer. The optimized MLD coatings exhibits a low reflectance of 0.017% under photoresist at the exposure angle of 17.8 degrees for 413 nm light and a high reflectance of 99.61% under air at the use angle of 51.2 degrees for 1053 nm light. Numerical calculation of intensity distribution in the photoresist coated on the MLD film during exposure shows that standing-wave patterns are greatly minimized and thus simulation profile of photoresist gratings after development demonstrates smoother shapes with lower roughness. Furthermore, a MLD gratings with grooves etched into the top layer of this MLD coating provides a high diffraction efficiency of 99.5% and a low electric field enhancement ratio of 1.53. This thin-film design shows perfect performances and can be easily fabricated by e-beam evaporation. (c) 2006 Elsevier B.V. All rights reserved.

水生植物凤眼莲的种内基因型差异与入侵模式

原产于亚马逊河流域的水生植物凤眼莲（Eichhornia crassipes）在花部结构上有三种花型（L、M和S），故其配殖系统（mating system）为典型的三型花柱（tristyly）。但在入侵地区，它却常只有M和L两种花型，其中尤以M型占据绝对优势，使有性繁殖水平大为下降。为了解释凤眼莲在入侵过程中，花型频率为何发生变化以及该变化对其在入侵地的适应性进化上有何影响，作者在中国西南的两个居群中连续两年开展了野外生长和人工授粉实验，对比分析水面和泥地两类不同生境中M和L在克隆生长、生物量积累以及有性繁殖水平等方面的异同，并利用RAPD、 ISSR片段比较了具M型和L型花植物个体间的遗传变异水平。对三型花柱这一长期引人注目的遗传模式的分子位点也尝试了连锁片段的克隆和测序。 克隆生长的对比实验发现，在2004年，漂浮生长的M个体平均克隆分株数为25.37，L为21.20，前者显示较强的克隆生长能力（t＝2.252， P< 0.05）;2005年的实验再次证实M（每个个体19.83个分株）比L（每个个体15.53分株）表现出了显著较强的克隆优势（t＝2.631，P<0.001）。M较L多产生克隆约24%。 但在岸边泥地上固着生长时，2004年L个体平均克隆分株为16.20，M 为10.17个分株。L表现出了更强的克隆生长能力（t＝4.788，p<0.001），与漂浮生长状况下的情形恰恰相反，暗示M与L个体可能存在一定的生态位分化。这种分化可能是在入侵过程中形成的，也可能反映了原产地亚马孙流域旱涝交替造成的固着生长与漂浮生长交替发生的种内适应性。 生物量（干重）的对比分析发现，M个体在漂浮生长和固着生长的情况下都比L有着更高的生物量积累（漂浮生长实验：t＝6.173，p<0.005（2004年）;t＝6.99，p<0.001（2005年）。固着生长实验：t＝4.029，p<0.001）。生物量对凤眼莲的竞争和过冬有着一定的作用，因此较大的生物量积累可能是M个体在当地气候和环境中逐渐适应的一个结果。 有性繁殖的实验包括了实验个体的花序数与花朵数、自交与异交人工授粉的结实情况以及种子萌发率等方面的对比分析。结果表明，虽然M和L个体在花序数和花朵数上不存在显著差异，但是M个体在自交和异交的种子产量上比L略高，尤其是自交的种子产量，M显著高于L（M平均每个蒴果的自交种子产量为139.8，L为76.2）。以各100粒种子进行萌发实验，发现两花型之间在种子萌发率上不存在显著差异。对于M而言，其自交种子产量远大于异交种子产量 （139.8 vs. 93.3），且种子萌发率也略大于异交的种子萌发率（自交种子萌发率45.47％，异交种子萌发率 30.73％）。结合以上的实验结果，本文认为M基因型优势的形成可能与M个体与当地环境长期适应导致的生长与繁殖 上的优势有关。M的本地适应性是建立在特定的遗传背景上时，异交反而会破坏这种遗传组合，造成远交衰退。 对40个M和30个L个体进行20个RAPD引物和20个ISSR引物的遗传分析时发现，所有个体在RAPD表型上没有区别，但是在M中出现了3个ISSR表型，在L中出现了2个ISSR表型。本文还尝试利用RAPD技术扫描与三型花柱的遗传位点连锁的DNA片段。在146个RAPD随机引物中，初步发现两个候选片段，一个750bp，另一个2 000bp;已对它们进行了克隆、测序。 这些初步实验表明凤眼莲在我国的入侵可能伴随着基因型的差异表现和居群遗传分化，这种基因型的差异表现对该植物的成功入侵具有作用。其中，花型为M的个体的优势生长解释了该花型在中国分布区内的主导地位。推测该生长优势的遗传基础可能来源于基因组内较高的杂合子水平和在入侵地较长的适应历史，但最终结论尚有待进一步的实验证据。

Feeding rates affect heat shock protein levels in liver of larval white sturgeon (Acipenser transmontanus)

A two-week trial was conducted to study the effect of feeding rates on heat shock protein levels in larval white sturgeon. The larvae (30 day post hatch, 230 mg initial body weight) were fed a commercial feed (12.6% moisture, 49.5% crude protein. 20.7% Crude fat, and 8.6% ash) at 5, 15. or 25% body weight per clay (BW d(-1)). Liver heat shock proteins (Hsp) were measured before and after the larvae were subjected to a heat shock from 18 to 26 degrees C at 1 degrees C/15 min and maintained at 26 degrees C for 4 h thereafter. Before heat shock, larvae fed 5% BW d(-1) had significantly (P<0.05) lower final body weight, RNA/DNA ratio, whole body lipid and protein content, and Hsp60 and Hsp70 levels but higher protein efficiency ratio, and whole body moisture content than larvae fed the two higher feeding rates. Heat shock significantly induced Hsp60 and Hsp70 levels in the liver of all fish but they were lower in larvae fed the 5% than those fed 15 and 25% BW d(-1). Hsp70 level increased much more than Hsp60 after the heat shock Suggesting that Hsp70 is a more sensitive biomarker under our experimental conditions. (c) 2008 Elsevier B.V. All rights reserved.

Effects of micronutrients on biological treatment efficiency of textile wastewater

Micronutrients play a very important role in biological processes for wastewater treatment. Many industrial wastewaters lack in nutrients (macronutrients and micronutrients) required for microbial growth, and this is one of the main problems at many activated sludge plants treating industrial wastewater. The microbial community structure is one of the important factors controlling the pollutant-degrading capacity of biological wastewater treatment system. In this study, the concentrations of micronutrients of the textile wastewater discharged from a textile plant were determined, and the effects of micronutrients on treatment efficiency and microorganism community structure of the biological treatment system were studied. The results showed that the optimal concentrations of magnesium, molybdenum, zinc, thiamine and niacin in the textile wastewater were 5.0, 2.0, 1.0, 1.0 and 1.0mg/L, respectively. The COD removal rates when magnesium, molybdenum, zinc, thiamine and niacin were added individually to the wastewater in their optimal concentrations were 1.8, 1.4, 1.3, 1.6 and 2.2 times of that of the control, respectively. The improving effects of combinations of zinc and thiamine, zinc and niacin, thiamine and niacin were better than single micronutrient. The diversity of quinones (DQ) changed significantly after the micronutrient was added into the wastewater treatment system. This indicated that there was probably a feasibility of optimizing the biological treatment performances and microorganism community structure of textile wastewater treatment system through micronutrient supplement.

Differentiate performance of eight filter media in vertical flow constructed wetland: Removal of organic matter, nitrogen and phosphorus

A comparative study was conducted to reveal the differentiate effects of eight different filter media including gravel, zeolites, anthracite, shale, vermiculite, ceramic filter media, blast furnace steel slag and round ceramsite. The study mainly related to the eight different filter media's removal performances of organic matter, nitrogen and phosphorus in the vertical flow constructed wetland simulated system, which treating wastewater at hydraulic loading rate of 1000-2500 mm/d. The results indicated that the removal effects were closely related to the physical and chemical properties of medium materials. Anthracite-filled system had the highest removal rate for the total organic carbon (TOC), up to 70%, and the removal rates of other systems ranged from 20% to 30%. As for the five-day biochemical oxygen demand (BOD5), anthracite-filled and steel slag-filled systems had the highest removal rates, also up to 70%, as well as other systems all exceeded 50%. At the same time, for the total nitrogen (TN) and NH4(+)-N, the zeolites-filled and ceramic-filled systems had the best performances with the removal rates of more than 70%, the other way round, the removal rates of other systems were only about 20%. The distinguishable effects were also observed in removal performances of total phosphorus (TP) and total dissoluble phosphorus (TDP). The removal rates of TP and TDP in steel slag-filled systems were more than 90%, a much higher value, followed by that of the anthracite-filled system, more than 60%, but those of other systems being the less. Our study provided a potential mechanism to optimize the filter media design for the vertical flow constructed wetlands.

Photosynthetic recovery of desiccated intertidal seaweeds after rehydration

Intertidal seaweeds experience periodical desiccation and rehydration to different extents due to the tidal cycles and their vertical distributions. Their photosynthetic recovery process during the rehydration may show different patterns among the seaweeds from different zonations or depths at intertidal zone. In this study 12 species of seaweeds collected from the upper, middle, lower and sublittoral zones were examined. The relationship of the photosynthetic recovery to vertical distribution was assessed by comparing their patterns of photosynthetic and respiratory performances after rehydration following desiccation. Both the photosynthesis and dark respiration declined during emersion, showing certain degrees of recovery after re-immersion into seawater for most species, but the extents were markedly different from one species to the other. The species from upper intertidal zone after being rehydrated for 1 hour, following 2 hours of desiccation, achieved 100 % recovery of their initial physiological activity, while most of the lower or sublittoral species did not achieve full recovery. It is the ability to withstand desiccation stress (fast recovery during rehydration), but not that to avoid desiccation (water retaining ability) that determines the distribution of intertidal seaweeds. Such physiological behavior during rehydration after desiccation reflects the adaptive strategy of intertidal seaweeds against desiccation and their capability of primary production in the process of rehydration.