蒸汽引射稠油输送新技术

摘要：管线输送是稠油输运的一种主要手段。由于我国一些油田原油粘度高，常温下流动性差，管输需采用特殊工艺。根据粘度随温度沿指数下降的规律，与其它工艺比较，加热输送工艺有更大的潜力。该文提出了一种蒸汽引射直接加热稠油输送的新技术。为研究其有效性，进行了性能分析，并在辽河油田φ80mm，300m输油管线上进行了现场实验，测量了三种工况下该方法对稠油的温度、压降和含水串的影响。实验结果表明该文提出的方法是可行的。

用于稠油输送的新蒸汽引射器

介绍一种自行研制的蒸汽引射器，蒸汽以自由射流形式注入到输油管中，利用蒸汽释放的热量提高稠油温度以降低黏度，从而达到低输送压降的目的。该引器具有加热效率高，防止稠油堵塞管线等优点，引射器已在辽河油田输油管线上进行了现场实验，取得了很好的效果。

Coflow jets with large velocity difference - a new aerodynamic principle of flame stabilization and combustion intensification

A new aerodynamic principle of flame stabilization and combustion intensification, the coflow jets with large velocity difference, is described. One or more small high-velocity jets of air or steam, injected off the axis and in the same direction as the low-velocity main fuel-air flow into the combustor, create a large recirculation zone of high turbulence intensity in which the combustibles and high temperature gases are effectively mixed, so that stable and intensive combustion can be maintained even for fuels with poor ignition. A pulverized coal combustor based on the principle mentioned above is shown to be characteristic of excellent combustoom and a simple structure. A number of precombustors of this type are in operation at some power stations and industrial boilers of China. Using such precombustor, successtul startups and part-load operation of the boilers have become available under conditions of unpreheated air and low-grade coal with volatiles as low as 15% and ash content as high as 30%. This principle shows good promise as an attractive new technology of combustion.

注蒸汽井套管应力的数值计算与工业应用

在注蒸汽吞吐井的井筒应力模型中引入井筒温度场，利用ANSYS软件对不同约束条件下井简的应力场进行了计算．结果表明，最大热应力发生在套管内壁，超过了N80套管的弹性屈服极限，最大热膨胀发生在温度过渡区．当套管周围掏空时，热应变远大于材料的弹性极限应变，是诱发热采井套管变形损坏的主要原因．为此提出了相应的套管损坏防治措施，在油田现场采用厚壁合金钢TP120TH套管完井，试验结果验证了防治措施的有效性．

水蒸气对氧化钙脱氯效率影响的实验研究

本文采用实验方法,在一个流化床反应器中研究160～750℃下水蒸气的存在对HCl脱除效率(RE)的影响.实验结果表明:在低温区,水蒸气对RE的影响不明显;380℃时水蒸气的存在抑制反应进行;580℃和750℃时,脱除效率先下降,当水蒸气含量达到15%时,又呈现上升趋势.对于水蒸气含量为5%、10%和15%情况下,580℃的脱氯效率最高.最后通过对暴露的反应物表面积和HCl气体穿越产物层扩散过程的分析解释实验得到的规律.

Design and Operation of A 5.5 MWe Biomass Integrated Gasification Combined Cycle Demonstration Plant

The design and operation of a 5.5 MWe biomass integrated gasification combined cycle (IGCC) demonstration plant, which is located in Xinghua, Jiangsu Province of China, are introduced. It is the largest complete biomass gasification power plant that uses rice husk and other agricultural wastes as fuel in Asia. It mainly consists of a 20 MWt atmospheric circulating fluidized-bed gasifier, a gas-purifying system, 10 sets of 450 kW(e) gas engines, a waste heat boiler, a 1.5 MWe steam turbine, a wastewater treatment system, etc. The demonstration plant has been operating since the end of 2005, and its overall efficiency reaches 26-28%. Its capital cost is less than 1200 USD/kW, and its running cost is about 0.079 USD/kWh based on the biomass price of 35.7 USD/ton. There is a 20% increment on capital cost and 35% decrease on the fuel consumption compared to that of a 1 MW system without a combined cycle. Because only part of the project has been performed, many of the tests still remain and, accordingly, must be reported at a later opportunity.

Study on the technology of thermal cracking of paraffin to alpha olefins

Alpha olefins are mainly produced from paraffin cracking in China, but their quality is not good because of bad quality of cracking feed and outdated technology. The technology of paraffin once-through cracking, paraffin recycle cracking of removing the heavy fraction after wax vaporizing and that of removing the heavy fraction before wax vaporizing were investigated in this paper. It was found that the technology of paraffin recycle cracking of removing the heavy fraction before wax vaporizing is new and better under the same operating conditions. Using hard paraffin (mp 54-56 degrees C) as feed, the high-quality alpha olefins products (C-5-C-21) containing more than 97 wt% of olefins and more than 88 wt% of alpha olefins are produced under optimum process conditions, which are a steam to paraffin ratio of 15 wt%, process temperature of 600 degrees C, low hydrocarbon partial pressure and residence time of 2 s. In addition, with the technology of the second injecting steam in ethylene cracking used in paraffin cracking, producing coke in paraffin cracking furnace has been markedly reduced.

Periodic bubble emission and appearance of an ordered bubble sequence (train) during condensation in a single microchannel

Condensation of steam in a single microchannel, silicon test section was investigated visually at low flow rates. The microchannel was rectangular in cross-section with a depth of 30 pm, a width of 800 mu m and a length of 5.0 mm, covered with a Pyrex glass to allow for visualization of the bubble formation process. By varying the cooling rate during condensation of the saturated water vapor, it was possible to control the shape, size and frequency of the bubbles formed. At low cooling rates using only natural air convection from the ambient environment, the flow pattern in the microchannel consisted of a nearly stable elongated bubble attached upstream (near the inlet) that pinched off into a train of elliptical bubbles downstream of the elongated bubble. It was observed that these elliptical bubbles were emitted periodically from the tip of the elongated bubble at a high frequency, with smaller size than the channel width. The shape of the emitted bubbles underwent modifications shortly after their generation until finally becoming a stable vertical ellipse, maintaining its shape and size as it flowed downstream at a constant speed. These periodically emitted elliptical bubbles thus formed an ordered bubble sequence (train). At higher cooling rates using chilled water in a copper heat sink attached to the test section, the bubble formation frequency increased significantly while the bubble size decreased, all the while forming a perfect bubble train flowing downstream of the microchannel. The emitted bubbles in this case immediately formed into a circular shape without any further modification after their separation from the elongated bubble upstream. The present study suggests that a method for controlling the size and generation frequency of microbubbles could be so developed, which may be of interest for microfluidic applications. The breakup of the elongated bubble is caused by the large Weber number at the tip of the elongated bubble induced by the maximum vapor velocity at the centerline of the microchannel inside the elongated bubble and the smaller surface tension force of water at the tip of the elongated bubble.