Effect of fabrication conditions on I-V properties for ZnO varistor with high concentration additives by sol-gel technique

Polycrystalline nano-grain-boundary multi-doping ZnO-based nonlinear varistors with higher concentration additives have been fabricated by sol-gel and standard solid-state reaction method, of which the best sample has a very high threshold voltage of E-b = 3300 V/mm. The effect of sintering processes, sintering temperature and sintering time, and that of additive concentration of Bi2O3 on E-b of the samples are systematically investigated. The results show that the great merit of sol-gel method is its high threshold voltage obtained by a lower sintering temperature than the solid-state reaction method. The present work also shows that five phases including solid-state sintering, rich Bi liquid phase formation and ZnO as well as other additive dissolution, ZnO grain growth, the secondary phase sufficient formation and evolution have been experienced at different sintering temperatures. The hole type defect and nonhomogeneity of the microstructure will lead to the decrease of threshold voltage, i.e., the grain size and the homogeneity of the material will be important factors and directly affect the characteristic of the varistor. The sintering characteristic and the influence of Bi2O3 content on the threshold voltage are also discussed. (c) 2004 Elsevier B.V. All rights reserved.

西藏产雪莲花的化学成分研究

本学位论文报道了作为传统藏药材广泛使用的西藏产雪莲花化学成分的研究。论文由五章组成，第一章是三种西藏产雪莲花的化学成分的系统分离纯化和结构鉴定；第二章为西藏产雪莲花化学成分的液-质及串联质谱联用分析；第三章提出了以HPLC和TLC为检测方法的雪莲花药材质量标准草案；第四章给出了对西藏产雪莲花挥发油化学成分的气-质联用分析结果；第五章概述了雪莲花的化学成分及药理研究进展。 第一章包括三个部分。第一部分报道了绵头雪莲花(Saussurea laniceps Hand.-Mazz.)全草乙醇提取物化学成分的分离鉴定。采用正相硅胶柱层析及凝胶柱层析等分离方法，从西藏产绵头雪莲花的乙醇提取物中共分离鉴定出15个化合物。其中11个化合物为首次从该植物中分离得到，当中2个化合物系在凤毛菊属植物中首次发现。第二部分报道了水母雪莲花(Saussurea medusa Maxim.)全草乙醇提取物的化学成分。采用正、反相硅胶柱层析及凝胶柱层析等分离方法，共分离鉴定出15个化合物，其中1个为新化合物，另有4个化合物为首次从该植物中分离得到。新化合物结构通过质谱和一维及二维核磁共振等波谱解析方法及碱水解反应确定为巴豆酰基-高车前苷(M-7)。第三部分报道了三指雪莲花 (Saussurea tridactyla Sch.-Bip. ex Hook. f.)全草乙醇提取物的化学成分。采用正相硅胶柱层析及凝胶柱层析等分离方法，共分离鉴定出7个化合物，其中1个化合物为首次从该植物中分离得到。 第二章也包括三个部分。首先是采用液-质联用(HPLC-DAD-ESI-MSn)分析方法，对7个西藏不同产地的三指雪莲花化学成分进行了分析，通过与标准品的 UV和MS数据比较，共鉴定出14个峰，并对其中8个共有成分进行了定量测定。其次是关于八种西藏产雪莲花化学成分的液-质联用(HPLC-DAD-ESI-MSn)分析，通过与标准品的UV和MS数据比较，共鉴定出15个峰，并对其中8个共有成分进行了定量检测。最后通过对八种西藏产雪莲花主要化学成分的多级串联质谱(ESI-MSn)分析，快速、灵敏地鉴定出10个黄酮和3个香豆素化学成分。 第三章同样包括三个部分。首先是以绵头雪莲花中主要香豆素成分东莨菪素和伞形花内酯为对照品，通过TLC定性检测和HPLC含量测定，草拟出较严谨的药材质量标准。其次是将绵头雪莲花、三指雪莲花和雪兔子作为一个药材看待，草拟了以东莨菪素和伞形花内酯的TLC检测为指标的药材质量标准。最后是针对水母雪莲花，以主要黄酮成分芹菜素-7-O-b-D-葡萄糖苷为对照品作TLC检测，并草拟出该药材的质量标准草案。 第四章报道了西藏产雪莲花挥发油的化学成分分析。采用传统水蒸气蒸馏法分别从八种雪莲花全草中提取挥发油，利用气相色谱-质谱联用技术分别从水母雪莲花、绵头雪莲花、槲叶雪莲花、云状雪兔子、拉萨雪兔子、小果雪兔子、雪兔子和三指雪莲花中分别鉴定出83、83、56、34、21、20、24和20个化学成分，分别占其挥发油总量的70.7%、76.0%、82.2%、55.4%、49.7%、70.4 %、76.2%和 76.7%。 第五章为综述，总结和概括了雪莲花的化学和药理研究进展。 The dissertation reports the investigation of the chemical constituents of the genus Saussurea. Quite a lot of species in this genus are traditional Tibetan medicinal plants, and hence have been widely used in traditional Tibetan medicine. This dissertation consisted of five chapters. The first chapter is on the chemical constituents of three Saussurea plants. The second section is about the analysis of chemical constituents of Saussurea plants using HPLC-MS and ESI-MS/MS. In the third chapter, we proposed quality-control standards for the Genus Saussurea based on TLC (thin layer chromatography) and HPLC. The fourth chapter is about chemical compositions of the essential oil from the whole plant of Saussurea plants. The last chapter reviews the research progress of the Genus Saussurea. The first chapter consists of three parts. The first part is about chemical constituents of ethanol extracts from whole plant of Saussurea laniceps Hand.-Mazz. Fifteen compounds were isolated by column chromatography on normal phase silica gel and Sephadex LH-20. Among them, eleven compounds were isolated from this plant for the first time, and two compounds were isolated from Genus Saussurea for the first time. The second part is about chemical constituents of ethanol extracts from whole plant of Saussurea medusa Maxim. Fifteen compounds were isolated by column chromatography on normal phase, reversed phase silica gel and Sephadex LH-20. Five of them were isolated from this plant for the first time, and there is one new flavonoid glucoside which was identified as 6″-O-crotonoyl-homoplantaginin (M-7) based on the evidence of one- and two-dimensional nuclear magnetic resonance, mass spectrometry analysis, and alkaline hydrolysis reaction. The last part is about chemical constituents of ethanol extracts from whole plant of Saussurea tridactyla Sch.-Bip. ex Hook. f.. Seven compounds were isolated by column chromatography on normal phase silica gel and Sephadex LH-20. There is one compound which was isolated from this plant for the first time. The second chapter consists of three parts. In the first part, we analyzed the chemical constituents of S. tridactyla collected from seven different places in Tibet using HPLC-DAD-ESI-MSn. Fourteen peaks in the HPLC were identified by comparison of UV and MS spectra with those of authentic compounds, among which eight common peaks were quantified. In the second part, we analyzed the chemical constituents of eight Saussurea species using HPLC-DAD-ESI-MSn method. Fifteen peaks in the HPLC were identified by comparison of UV and MS spectra with those of authentic compounds and eight main peaks of them were quantified. In the last part, we analyzed the chemical compounds of the above eight Saussurea plants directly by ESI-MS/MS. Thirteen major compounds, including 10 flavonoids and 3 coumarins were easily rapidly identified. The third chapter consists of three parts. In the first part, we proposed a comparative high quality-control standard for S. laniceps, based on quality detection by TLC and quantity analysis by HPLC using two major compounds (umbelliferone and scopoletin) as standard compounds. In the second part, in viewing S. laniceps, S. tridactyla and S. gossypiphora as the members of one family of medicinal herbs, we suggested a quality-control standard based on the TLC detection of the two major compounds (umbelliferone and scopoletin). In the last part, we proposed a quality-control standard for S. medusa based on the TLC detection of its major component (apigenin 7-O-glucoside). The four chapter analyzed the chemical constituents of essential oil of eight Saussurea species. The essential oils were extracted from the whole plants of these samples with water stream distillation. By GC-MS analysis, we identified eighty-three compounds from S. medusa, eighty-three from S. laniceps, fifty-six from S. quercifolia, thirty-four from S. aster, twenty-one from S. kingii, twenty from S. simpsoniana, twenty-four from S. gossypiphora, and twenty from S. tridactyla respetively, which accounted for 70.7%, 76.0%, 82.2%, 55.4%, 49.7%, 70.4 %, 76.2% and 76.7% of the total essential oil, respectively. The last chapter reviews the research progress of the Genus Saussurea.

5-氟尿嘧啶-β-环糊精结肠靶向前体药物的研究

5-氟尿嘧啶(5-Fluorouracil， 5-FU)是一种抗代谢药物，广泛用于临床治疗结直肠癌、胃癌、乳腺癌等多种癌症，但其首过代谢显著、亲脂性较低，选择性差、毒副作用大。为克服这些缺点人们对5-FU进行了大量的修饰工作，包括小分子修饰以及与各种载体形成微球、微囊、纳米粒、共价前药等。 环糊精(Cyclodextrin，简称CD)，可被结肠中的糖苷酶特异性地降解成小分子糖，而胃和小肠中由于缺乏相应的酶而使环糊精不被降解，这一特性在结肠药物的靶向输送及释放中有重要应用价值。环糊精中含有丰富的羟基，易进行化学修饰，将药物与环糊精通过共价键结合制成前药，使其在胃和小肠中不降解，而在盲结肠中被特异性的酶降解释出药物，达到结肠靶向释药的目的。研究表明，环糊精作为一种前药载体为结肠靶向释药和缓释、控释系统提供了一种有效的手段。 本工作选择5-氟尿嘧啶为模型药物、β-环糊精作为载体，通过中间体5-FU羧酸衍生物的制备及其与β-环糊精的偶联，合成了系列5-FU-β-CD前体药物，并利用紫外、红外、质谱、核磁、元素分析、热分析等手段对其进行结构表征。同时，还研究了前体药物的体外释药性质。具体内容包括： 1. 含有羧基的5-FU衍生物中间体的合成：(5-氟尿嘧啶-1-基)-乙酸(FUAC)、3-(5-氟尿嘧啶-1-基)-丙酸(FUPC)、5-(5-氟尿嘧啶-1-基)-戊酸(FUVC)的合成。 2. 中间体5-FU的羧酸衍生物与β-CD的偶联：分别通过以6-OTs-β-CD为中间体的取代法和活化酯法，合成了第一面取代和第二面取代的5-FU-β-CD大分子前体药物。在二面取代的前体药物制备中，通过改变原料的比例，合成了系列不同取代度(DS)的2-[(5-氟尿嘧啶-1-基)-乙酰基] -β-环糊精结合物。 3. 对上述前体药物进行体外释放研究：分别考察了前体药物在不同pH缓冲溶液中的水解行为及其在小鼠胃肠道人工体液中的酶解行为，并通过UV-Vis及HPLC对前体药物释放情况进行检测分析。 5-Fluorouracil(5-Fu), commonly known as a broad-spectrum antineoplastic drug, has been widely used in the treatment of various kinds of cancer including colon cancer for 40 years. However, this antitumor agent exhibits serious adverse effects, such as their marrow toxicity, gastrointestinal reaction and low selectivity in their clinical use. In order to improve its antitumor activity and reduce its toxicity, the compound was modified in various ways, including the formation of conjugated prodrugs with kinds of carrier, microsphere and nanoparticles etc. Cyclodextrins(CDs) are known to be barely capable of being hydrolyzed and only slightly absorbed in passing through the stomach and small intestine; however they are fermented into small saccharides by colonic microflora and thus absorbed as small saccharides in the large intestine. This biodegradation property of CDs may be useful as a colon-targeting carrier, and thus CD prodrugs may serve as a source of site-specific delivery of drugs to colon. It was demonstrated that prodrugs of CDs can provide a versatile means for construction of not only colon targeted delivery systems, but also delayed release systems. 5-Fluorouracil was taken as a model drug and β-CD as the carrier in this study. Series prodrugs of 5-FU was prepared through the preparation of reactive 5-FU derivatives containing carboxyl group and coupling to hydroxyl groups of CD. The structures of the conjugates were charactered by using IR, UV–vis, ESI-MS, 1H, 13C-NMR spectra, elemental analyses, and thermal analysis. In vitro hydrolysis behavior in aqueous solution and in rat gastrointestinal tract contents of the conjugates were also investigated. The main content of this dissertation includes following aspects: 1. The preparation of 5-FU derivatives containing carboxyl group: 5-Fluorouracil- acetic acid(FUAC)、3-(5-FU-1)-propionic acid (FUPC)、and 5-(5-FU-1)-valeric acid(FUVC). 2. The coupling of 5-FU derivatives to β-CD: 5-FU was selectively conjugated onto the primary or secondary hydroxyl groups of β-CD through an ester linkage, by the substitution of 6-OTs-β-CD and the activated ester method respectively. For the secondary face conjugation, the degree of substitution(DS) can be controlled by changing the mole ratio of the starting materials(FUAC and β-CD). 3. In vitro release behavior of the conjugates in aqueous solution and in rat gastro- intestinal tract contents of the conjugates were investigated, and the reaction was monitored and analyzed by using UV-Vis and HPLC methods.

Low-temperature heat capacities and derived thermodynamic functions of cyclohexane

The low-temperature heat capacities of cyclohexane were measured in the temperature range from 78 to 350 K by means of an automatic adiabatic calorimeter equipped with a new sample container adapted to measure heat capacities of liquids. The sample container was described in detail. The performance of this calorimetric apparatus was evaluated by heat capacity measurements on water. The deviations of experimental heat capacities from the corresponding smoothed values lie within +/-0.3%, while the inaccuracy is within +/-0.4%, compared with the reference data in the whole experimental temperature range. Two kinds of phase transitions were found at 186.065 and 279.684 K corresponding solid-solid and solid-liquid phase transitions, respectively. The entropy and enthalpy of the phase transition, as well as the thermodynamic functions {H-(T)- H-298.15 K} and {S-(T)-S-298.15 K}, were derived from the heat capacity data. The mass fraction purity of cyclohexane sample used in the present calorimetric study was determined to be 99.9965% by fraction melting approach.

Heat capacities and thermodynamic properties of chrysanthemic acid

The heat capacities of chrysanthemic acid in the temperature range from 80 to 400 K were measured with a precise automatic adiabatic calorimeter. The chrysanthemic acid sample was prepared with the purity of 0.9855 mole fraction. A solid-liquid fusion phase transition was observed in the experimental temperature range. The melting point, T-m, enthalpy and entropy of fusion, Delta(fus)H(m), Delta(fus)S(m), were determined to be 390.741 +/- 0.002 K, 14.51 +/- 0.13 kJ mol(-1), 37.13 +/- 0.34 J mol(-1) K-1, respectively. The thermodynamic functions of chrysanthemic acid, H-(T)-H-(298.15), S-(T)-S-(298.15) and G((T))-G((298.15)) were reported with a temperature interval of 5 K. The TG analysis under the heating rate of 10 K min(-1) confirmed that the thermal decomposition of the sample starts at ca. 410 K and terminates at ca. 471 K. The maximum decomposition rate was obtained at 466 K. The purity of the sample was determined by a fractional melting method.

Microencapsulation of n-hexadecane as a phase change material in polyurea

For thermal energy storage application, polyurea microcapsules about 2.5 mum in diameter containing phase change material were prepared using interfacial polycondensation method. In the system droplets in microns are first formed by emulsifying an organic phase consisting of a core material ( n-hexadecane) and an oil-soluble reactive monomer, toluene-2, 4-diisocyanate (TDI), in an aqueous phase. By adding water-soluble reactive monomer, diamine, monomers TDI and diamine react with each other at the interface of micelles to become a shell. Ethylenediamine (EDA), 1, 6-hexane diamine (HDA) and their mixture were employed as water-soluble reactive monomers. The effects of diamine type on chemical structure and thermal properties of the microcapsules were investigated by FT-IR and thermal analysis respectively. The infrared spectra indicate that polyurea microcapsules have been successfully synthesized; all the TG thermographs show microcapsules containing n-hexadecane can sustain high temperature about 300 degreesC without broken and the DSC measurements display that all samples possess a moderate heat of phase transition; thermal cyclic tests show that the encapsulated paraffin kept its energy storage capacity even after 50 cycles of operation. The results obtained from experiments show that the encapsulated n-hexadecane possesses a good potential as a thermal energy storage material.

Synthesis and spectroscopic study of mesoporous aluminum methylphosphonate foam templated by dibutyl methylphosphonate

New types of templates and novel interactive mechanisms between template and framework are very important for creating porous materials. In this work, by using neutral dibutyl methylphosphonate as a template, an inorganic-organic hybrid mesoporous material, aluminum methylphosphonate, was prepared. The as-synthesized material was studied by P-31 magnetic angle spinning nuclear magnetic resonance (MAS NMR), Al-27 MAS NMR, C-13 CP/MAS, FT-IR spectroscopy, thermogravimetry (TG), differential thermal analysis (DTA), and transmission electron microscopy. After thermal treatment at 673 K and 10 mmHg for 2 h, hybrid mesoporous foam was obtained. The transformation process was investigated by FT-IR. TG-DTA results indicate that the methyl group bonded to the framework keeps intact up to 792 K under air and 823 K under nitrogen. The characterization results from nitrogen gas adsorption-desorption measurements show that the BET surface area and the Barrett-Joyner-Halenda desorption cumulative pore volume of the foam are 90 m(2) g(-1) and 0.32 cm(3) g(-1) respectively. (C) 2003 Elsevier Inc. All rights reserved.

Surface-modified Nafion membranes with mesoporous SiO2 layers via a facile dip-coating approach for direct methanol fuel cells

In this study. Nafion (R) 117 membrane is surface-modified with mesoporous silica layers through in situ surfactant-templated sol-gel reaction. The reaction makes use of tetraethyl orthosilicate (TEOS) under acidic condition via dip-coating technique on both sides. Scanning electron microscopy (SEM), Fourier transformation infrared (FTIR), and thermogravimetric analysis (TGA) are employed to characterize the resultant membranes. Proton conductivity and methanol permeability of the membranes are also studied.

Assembly of Seven Supramolecular Compounds with p-Sulfonatocalix[6]arene

Seven supramolecular compounds comprising p-sulfonatocalix[6]arene and transition metals, {[Cu(Imz)-(phen)(H2O)](4)[C6AS]}center dot 10H(2)O (1), {[Cu(Imz)(2)(phen)](2)[Cu(Imz)(phen)(H2O)(2)](2)[C6AS]}center dot 13.3H(2)O (2), {[M(phen)(2)(H2O)]-[(M(phen)(2)](2)[C6AS]}center dot nH(2)O (3 and 4) (3: M = Co and n = 29.6; 4: M = Zn and n = 29.9), {[Cu(phen)(2)](4)[C6AS]}(2)center dot 13H(2)O (5), [H3O](2)[Co(phen)(3)](2)[C6AS]center dot 10.7H(2)O(6), and [Cu(phen)(2)(H2O)](2){[Cu(phen)(2)](2)[C6AS]}center dot 8H(2)O(7)(phen = 1,10-phenanthroline, C6AS = p-sulfonatocalix[6]arene, Imz = imidazole), have been synthesized by a hydrothermal method and structurally characterized by IR spectroscopy, thermogravimetric-differential thermal analysis (TG-DTA), and single crystal X-ray diffraction.

Double-ceramic-layer thermal barrier coatings of La2Zr2O7/YSZ deposited by electron beam-physical vapor deposition

Double-ceramic-layer(DCL) thermal barrier coatings (TBCs) of La2Zr2O7 (LZ) and yttria stabilized zirconia (YSZ) were deposited by electron beam-physical vapor deposition (EB-PVD). The composition, crystal structure, surface and cross-sectional morphologies and cyclic oxidation behavior of the DCL coating were studied. Both the X-ray diffraction (XRD) and thermogravimetric-differential thermal analysis (TG-DTA) prove that LZ and YSZ have good chemical applicability to form a DCL coating. The thermal cycling test at 1373 K in an air furnace indicates the DCL coating has a much longer lifetime than the single layer LZ coating. and even longer than that of the single layer YSZ coating. The failure of the DCL coating is a result of both the bond coat oxidation and the thermal strain between bond coat and ceramic layer generated by the thermal expansion mismatch.

Preparation and luminescence properties of Mn2+-doped ZnGa2O4 nanofibers via electrospinning process

One-dimensional Mn2+-doped ZnGa2O4 nanofibers were prepared by a simple and cost-effective electrospinning process. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), thermogravimetric and differential thermal analysis (TG-DTA), scanning electron microscopy (SEM), energy-dispersive X-ray spectrum (EDS), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), photoluminescence (PL) and cathodoluminescence (CL) spectra as well as kinetic decays were used to characterize the samples. SEM results indicated that the as-formed precursor fibers and those annealed at 700 degrees C are uniform with length of several tens to hundred micrometers, and the diameters of the fibers decrease greatly after being heated at 700 degrees C. Under ultraviolet excitation (246 nm) and low-voltage electron beams (1-3 kV) excitation, the ZnGa2O4:Mn2+ nanofibers presents the blue emission band of the ZnGa2O4 host lattice and the strong green emission with a peak at 505 nm corresponding to the T-4(1)-(6)A(1) transition of Mn2+ ion.

Self-assembled 3D flowerlike Lu2O3 and Lu2O3 : Ln(3+) (Ln = Eu, Tb, Dy, Pr, Sm, Er, Ho, Tm) microarchitectures: Ethylene glycol-mediated hydrothermal synthesis and luminescent properties

Three-dimensional flowerlike Lu2O3 and Lu2O3:Ln(3+) (Ln = Eu, Th, Dy, Pr, Sm, Er, Ho, Tm) microarchitectures have been successfully synthesized via ethylene glycol (EG)-mediated hydrothermal method followed by a subsequent heat treatment process. X-ray diffraction, Fourier transform infrared spectroscopy, energy-dispersive X-ray spectra, thermogravimetric and differential thermal analysis, elemental analysis, inductively coupled plasma atomic absorption spectrometric analysis, ion chromatogram analysis, X-ray photoelectron spectra, scanning electron microscopy, transmission electron microscopy, photoluminescence spectra as well kinetic decays, and cathodoluminescence spectra were used to characterize the samples. Hydrothermal temperature, EG, and CH3COONa play critical roles in the formation of the lutetium oxide precursor microflowers. The reaction mechanism and the self-assembly evolution process have been proposed. The as-formed lutetium oxide precursor could transform to Lu2O3 With their original flowerlike morphology and slight shrinkage in the size after postannealing process.

Polyimides Derived from 1,4-Bis [3-oxy-(N-aminophthalimide)] Benzene

A novel diamine, 1,4-bis [3-oxy-(N-aminophthalimide)] benzene (BOAPIB), was synthesized from 1,4-bis [3-oxy-(N-phenylphthalimide)] benzene and hydrazine. Its structure was determined via IR, H-1 NMR, and elemental analysis. A series of five-member ring, hydrazine-based polyimides were prepared from this diamine and various aromatic dianhydrides via one-step polycondensation in p-chlorophenol. The inherent viscosities of these polyimides were in the range of 0.17-0.61 dL/g. These polymers were soluble in polar aprotic solvents and phenols at room temperature. Thermogravimetric analysis (TGA) showed that the 5% weight-loss temperatures of the polyimides were near 450 degrees C in air and 500 degrees C in nitrogen. Dynamic mechanical thermal analysis (DMTA) indicated that the glass-transition temperatures (T(g)s) of these polymers were in the range of 265-360 degrees C. The wide-angle X-ray diffraction showed that all the polyimides were amorphous.

Coordination-Induced Formation of One-Dimensional Nanostructures of Europium Benzene-1,3,5-tricarboxylate and Its Solid-State Thermal Transformation

Novel one-dimensional europium benzene-1,3,5-tricarboxylate compressed nanorods have been synthesized oil it large scale through direct precipitation in solution phase under moderate conditions without the assistance of any surfactant, catalyst, or template. The obtained nanorods have widths of about 50-100 not, thicknesses of 10-20 nm, and lengths ranging from a few hundred nanometers to several micrometers. X-ray powder diffraction. elemental analysis, Fourier transform infrared Studies, and thermogravimetric and differential thermal analysis show that the nanorods have the structural formula of Eu(1,3,5-BTC)center dot 6H(2)O. Upon UV excitation, these nanorods exhibit a highly efficient luminescence. which comes from the Eu3+ ions. Moreover, Eu2O3 nanorods Could also be obtained via a thermal decomposition method using the corresponding complex as a precursor. This synthetic route is promising for the preparation of other one-dimensional crystalline nanomaterials because of its simplicity and the low cost of the starting reagents.

Y2O3 : Eu3+ microspheres: Solvothermal synthesis and luminescence properties

Y2O3 : Eu3+ microspheres, with an average diameter of 3 mu m, were successfully prepared through a large-scale and facile solvothermal method followed by a subsequent heat treatment. X-ray diffraction, Fourier transform infrared spectroscopy, energy-dispersive X-ray spectra, thermogravimetric and differential thermal analysis, inductive coupled plasma atomic absorption spectrometric analysis, scanning electron microscopy, transmission electron microscopy, photoluminescence spectra, as well kinetic decays, and cathodoluminescence spectra were used to characterize the samples. These microspheres were actually composed of randomly aggregated nanoparticles. The formation mechanisms for the Y2O3 : Eu3+ microspheres have been proposed on an isotropic growth mechanism. The Y2O3 : Eu3+ microspheres show a strong red emission corresponding to D-5(0) -> F-7(2) transition (610 nm) of Eu3+ under ultraviolet excitation (259 nm) and low-voltage electron beams excitation (1-5 kV), which have potential applications in fluorescent lamps and field emission displays.