Synthesis and temperature-dependent near-band-edge emission of chain-like Mg-doped ZnO nanoparticles

Chain-like Mg-doped ZnO nanoparticles were prepared using a wet chemical method combined with subsequent heat treatment. The blueshifted near-band-edge emission of the doped ZnO sample with respect to the undoped one was investigated by temperature-dependent photoluminescence. Based on the energy shift of the free-exciton transition, a band gap enlargement of similar to 83 meV was estimated, which seems to result in the equivalent shift of the bound-exciton transition. At 50 K, the transformation from the donor-acceptor-pair to free-to-acceptor emissions was observed for both the undoped and doped samples. The results show that Mg doping leads to the decrease of the acceptor binding energy. (c) 2006 American Institute of Physics.

Influence of ambient atmosphere on the plasmon resonance absorption of Ag/SiOx(0 <= x <= 2) nanocomposite film

Nanocomposite films consisting of nanosized Ag particles embedded in partially oxidized amorphous Si-containing matrices were prepared by radio frequency magnetron co-sputtering deposition. We studied the influence of ambient atmosphere during the preparation and heat-treatment of Ag/SiOx (0 less than or equal to x less than or equal to 2) nanocompositefilm on its optical absorption properties. We found that the plasmon resonance absorption peak shifts to shorter wavelengths with the increasing oxygen content in the SiOx matrix. The analysis indicates that the potential barrier between Ag nanoparticles and SiOx matrix increases with the increasing x value, which will induce the surface resonance state to shift to higher energy. The electrons in the vicinity of the Fermi level of Ag nanoparticles must absorb more energy to be transferred to the surface resonance state with the increasing x value. It was also found that the plasmon resonance absorption peaks of the samples annealed in different ambient atmospheres are located at about the same position. This is because the oxidation surface layer is dense enough to prevent the oxygen from penetrating into the sample to oxidize the silicon in the inner layer.

Photoluminescence study of CdSexS1-x quantum dots in a glass spherical microcavity

The photoluminescence (PL) of CdSexS1-x semiconductor quantum dots (QDs) in a glass spherical microcavity is investigated. The CdSexS1-x semiconductor clusters embedded in a glass matrix are fabricated by using the heat treatment method. Periodical structures consisting of sharp spectral lines are observed in the PL spectra of CdSexS1-x QDs, which can be well explained by the coupling with the whispering gallery modes of the spherical microcavity based on Mie scattering theory.

Effect of thermal annealing on hole trap levels in Mg-doped GaN grown by metalorganic vapor phase epitaxy

Deep trap levels in a Mg-doped GaN grown by metalorganic vapor phase epitaxy are studied with deep level transient spectroscopy (DLTS). The Mg concentration of the sample was 4.8 x 10(19) cm(-3), but the hole concentration was as low as 1.3x10(17) cm-3 at room temperature. The DLTS spectrum has a dominant peak D-1 with an activation energy of 0.41+/-0.05 eV, accompanied by two additional peaks with activation energies of 0.49+/-0.09 eV (D-2) and 0.59+/-0.05 eV (D-3). It was found that the dominant peak D-1 consists of five peaks, each of which has different activation energy and capture cross section. In order to investigate these deep levels further, we performed heat treatment on the same samples to observe the variations of activation energy, capture cross section, and amplitude of DLTS signals. It was found that the longer the heat treatment duration is, the lower the amplitude of DLTS peaks become. This suggests that the decrease of the DLTS signal originates from hydrogen atom outgoing from the film during the annealing process. The possible originality of multiple trap levels was discussed in terms of the Mg-N-H complex. (C) 2000 American Vacuum Society. [S0734-2101(00)01701-2].

Preparation and luminescence properties of Eu2+ in SiO2 xerogels

Al-doped and B, Al co-doped SiO2 xerogels with Eu2+ ions were prepared only by sol-gel reaction in air without reducing heat-treatment or post-doping. The luminescence characteristics and mechanism of europium doping SiO2 xerogels were studied as a function of the concentration of Al, B, the europium concentration and the host composition. The emission spectra of the Al-doped and B, Al codoped samples all show an efficient emission broad band in the blue violet range. The blue emission of the Al-doped sample was centered at 437 nm, whereas the B, Al co-doped xerogel emission maximum shifted to 423 nm and the intensity became weaker. Concentration quenching effect occurred in both the Al-doped and B, Al co-doped samples, which probably is the result of the transfer of the excitation energy from Eu2+ ions to defects. The highest Eu2+ emission intensity was observed for samples with the Si(OC2H5)(4):C2H5OH:H2O molar ratio of 1:2:4. (c) 2006 Elsevier B.V. All rights reserved.

三孢布拉氏霉发酵产β-胡萝卜素的研究

本论文研究了利用三孢布拉氏霉(Blakeslea trispora)发酵产β-胡萝卜素的培养条件。主要包括：发酵培养基的确定，发酵条件的优化。还考察了发酵菌丝体中β-胡萝卜素的提取方法及薄层层析等。 首先研究了培养基成分对三孢布拉氏霉发酵产β-胡萝卜素的影响。确立了玉米淀粉作为碳源，黄豆粉（热榨）作为氮源，棉籽油作为植物油的发酵培养基配方，其成分为：玉米淀粉 3％，黄豆粉（热榨） 2％，棉籽油 3％，KH2PO4 0.2%，MgSO4·7H2O 0.2%，维生素B1 0.002％，pH值6.0。 其次，通过比较不同的发酵影响因子，分别得到最适的条件：如三孢布拉氏霉正负菌接种比例为1.3：0.7，培养基pH值为7.0（灭菌后），发酵促进因子为Triton X-100。并采用正交试验法，确定其最佳发酵条件为正负菌接种比例1.3/0.7，发酵培养基pH为7.0，在培养基中添加表面活性基Triton X-100 0.08％。使该菌株产β-胡萝卜素的量达到0.73g/L，较初始发酵条件提高了3.3倍。 研究中还找到一个简便有效的对β-胡萝卜素的提取方法，选用盐酸-热处理法进行细胞破壁，并选用沸程为60～90℃的石油醚进行萃取。 用三孢布拉霉菌丝体内类胡萝卜索的石油醚提取液点样于硅胶G板，以丙酮：石油醚（5：95）为展开剂能将β-胡萝卜素与其它类胡萝卜索分离。该方法简便快速，并有一定实用价值。 The fermentative conditions of β-carotene by Blakeslea trispora have been investigated. These conditions include fermentation medium, the optimization of some fermentation factor. The extracting methods and the TLC of carotenoids were also researched. Firstly, the effects of composition of fermentation medium on the yield of β-carotene were studied. the results showed that the best fermentation medium was corn starch 3％，soybean power 2％，cottonseed oil 3％，KH2PO4 0.2%，MgSO4·7H2O 0.2%，vitamin B1 0.002％，pH value 6.0. Secondly, through compared some factors, such as different proportion of plus and minus strains, pH value, nonionic surfactants, respective best values have been obtained. The best proportion of plus and minus strains is 1.3:0.7, pH value of fermentation medium (sterilized) is 7.0, fermentation accelerant which acts as surfactants is Triton x-100. Farther on, the fermentative conditions were optimized through orthogonal experiment, the optimization showed that proportion of plus and minus strains is 1.3:0.7，pH value is 7.0, content of Triton x-100 is 0.08％. And the yield of β-carotene reached 0.73g/L, which was up to 3.3 times through the fermentation. In the extracting study, it has showed hydrochloric acid-heat treatment is a simple, convenient and effective extracting methods is which was used to destroy the cell wall, and the extracting organic solvent is petroleum ether whose boiling range is 60~90 ℃. In the TLC experiments, extracting contents in the petroleum ether were spotted in the silicagel plate, and the mixed liquor of acetone and petroleum ether (5：95) is developping agent, which can distinguish β-carotene from other carotenoids. It is a simple and quick technique.

Polymeric fullerene oxide films produced by decomposition of hexanitro[60]fullerene

A new poly(fullerene oxide) thin film material has been fabricated by thermal activation and electron bombardment on hexanitro[60]fullerene (HNF) film deposited on a An substrate, all under vacuum conditions. The reaction products in the polymerization process are analyzed by XPS, UPS, IR, TGA-MS and LDI-MS techniques. It is found that the main effect of thermal and radiation treatments is to induce cleavage of -NO bonds from HNF molecules resulted in the release of nitric oxide gas and the formation of fullerene-bound oxyradicals, C-60-C-6. Spectroscopic evidence strongly suggests that rearrangement of fullerenic nitro moieties into nitrito groups is involved in the HNF decomposition process prior to the generation of reactive oxyradical intermediates. Consequently, the intermolecular coupling reaction of these oxyradicals leads to carbon polymer networks containing oxygen-bridged fullerenes. The thermally generated polymeric thin film is stable up to 900 K. Electron bombardment is also effective in both the decomposition of -NO2 groups and the removal of -OH groups present in HNF films. UV irradiation at 365 nm alone is shown to be not as efficient for the polymer formation. (C) 2003 Elsevier Ltd. All rights reserved.

A novel method for preparing PEMFC catalytic layers

A novel PEMFC catalytic layer was fabricated by a Nafion-pyrolyzed method, which demonstrated a high performance with a maximum power density of 0.82 W/cm(2) on an electrode prepared by this method. The effects of the heat-treatment temperature and Nation content in the catalyst layer on performance were studied.

Activated carbon supported bimetallic CoMo carbides synthesized by carbothermal hydrogen reduction

A carbothermal hydrogen reduction method was employed for the preparation of activated carbon supported bimetallic carbide. The resultant samples were characterized by BET surface area measurement, X-ray diffraction, and temperature-programmed reduction-mass spectroscopy. The results showed that nanostructured beta-Mo2C can be formed on the activated carbon by carbothermal hydrogen reduction above 700 degreesC. The particle sizes of beta-Mo2C increase with increasing reaction temperatures and Mo loading. The bimetallic CoMo carbide can be synthesized by the carbothermal hydrogen reduction even around 600 degreesC. The bimetallic CoMo carbide is from carbothermal hydrogen reduction of CoMoO4 precursor and is easily formed when the Co/Mo molar ratio is 1.0. Separation of the bimetallic CoMo carbide phase into Mo carbide and Co metal occurs when the temperature of the reduction is above 700 degreesC. The addition of a second metal such as Co and Ni, decreases the formation temperature of carbide because the second metal promotes formation of CHx species from reactive carbon atoms or groups on carbon material and hydrogen, which further carburizes oxide precursors. (C) 2003 Elsevier Science Ltd. All rights reserved.

Pd nanoparticles supported on WO3/C hybrid material as catalyst for oxygen reduction reaction

Pd nanoparticles supported on WO3/C hybrid material have been developed as the catalyst for the oxygen reduction reaction (ORR) in direct methanol fuel cells. The resultant Pd-WO3/C catalyst has an ORR activity comparable to the commercial Pt/C catalyst and a higher activity than the Pd/C catalyst prepared with the same method. Based on the physical and electrochemical characterizations, the improvement in the catalytic performance may be attributed to the small particle sizes and uniform dispersion of Pd on the WO3/C, the strong interaction between Pd and WO3 and the formation of hydrogen tungsten bronze which effectively promote the direct 4-electron pathway of the ORR at Pd.

Microstructure and mechanical properties of Mg-4Al-4Nd-0.5Zn-0.3Mn alloy

Mg-4Al-4Nd-0.5Zn-0.3Mn alloy was prepared by metal mould casting method. Microstructure, aging behavior, mechanical properties and fracture morphology of the alloy were investigated. The results showed that alpha-Mg, Al-11 Nd-3, Al2Nd and Mg-32(Al,Zn)(49) phases were the main phases of the as-cast alloy. And the long rod-like Al-11 Nd-3 phase was decomposed to granular Al2Nd through T6 heat treatment. The tensile strength was also enhanced by T6 treatment. The yield strength was increased by 17% and 21% at RT and 150 degrees C, respectively. It was mainly because that the precipitates were refined through T6 treatment and this became more benefit to hinder dislocations slipping.

Development of durable carbon black/titanium dioxide supported macrocycle catalysts for oxygen reduction reaction

Carbon black and titanium dioxide supported iron tetraphenylporphyrin (FeTPP/TiO2/C) catalysts for oxygen reduction reaction (ORR) were prepared by sol-gel and precipitation methods followed by a heat-treatment at temperatures of 400-1000 degrees C. The FeTPP/C and TiO2/C were also studied for comparison. The FeTPP/TiO2/C pyrolyzed at 700 degrees C exhibits significantly improved stability while maintaining high activity towards ORR in comparison with the FeTPP/C counterpart. The electrochemical study combined with XRD, XPS, and SEM/EDX analyses revealed that the appropriate dispersion of TiO2 on the surface of FeTPP/TiO2/C catalysts, which depending on heat-treatment temperature, plays a crucial role in determining the activity and stability of catalysts.

Controllable Red, Green, Blue (RGB) and Bright White Upconversion Luminescence of Lu2O3:Yb3+/Er3+/Tm3+ Nanocrystals through Single Laser Excitation at 980 nm

Lu2O3:Yb3+/Er3+/Tm3+ nanocrystals have been successfully synthesized by a solvothermal process followed by a subsequent heat treatment at 800 degrees C. Powder X-ray diffraction, transmission electron microscopy, upconversion photoluminescence spectra, and kinetic decay were used to characterize the samples. Under single-wavelength diode laser excitation of 980 nm, the bright blue emissions of Lu2O3:Yb3+, Tm3+ nanocrystals near 477 and 490 nm were observed due to the (1)G(4)-> H-3(6) transition of Tm3+. The bright green UC emissions of Lu2O3:Er3+ nanocrystals appeared near 540 and 565 nm were observed and assigned to the H-2(11/2)-> I-4(15/2) and S-4(3/2)-> I-4(15/2) transitions, respectively, of Er3+. The ratio of the intensity of green luminescence to that of red luminescence decreases with an increase of concentration of Yb3+ in Lu2O3:Er3+ nanocrystals.