Application of capillary zone electrophoresis in the separation and determination of the curcuminoids in urine

The major components of the plant curcuma longa are the curcuminoids that include curcumin, demethoxycurcumin and bisdemethoxycurcumin. It has been reported the curcuminoids have some important activities. A new CZE method with diode array detection has been developed for the separation and determination of the curcumin, demethoxycurcumin and bisdemethoxycurcumin. Three curcuminoids could be readily separated within 7 min with a 15 mM sodium tetraborate buffer containing 10% methanol (v/v) at pH 10.8, 25 kV and 30 degrees C. The method has been validated and shows good performance with respect to selectivity, reproducibility, linearity, limits of detection and recovery. The proposed method was successfully applied to determine the curcuminoids in urine. (c) 2004 Elsevier B.V. All rights reserved.

Preparation of a novel polysulfone/polyethylene oxide/silicone rubber multilayer composite membrane for hydrogen-nitrogen separation

A novel poly sulfone/polyethylene oxide/silicone rubber (PSOPEO/SR) multilayer composite membrane was fabricated by double coating polysulfone substrate membrane with polyethylene oxide and silicone rubber. Gas permeation experiments were performed at 30 degrees C for hydrogen and nitrogen. PSf(PEO/SR membrane displayed high and steady performance for H-2/N-2: permeances of H-2 and N-2 of 49.51 and 0.601 GPU, respectively, and H-2/N-2 ideal separation factor of 82.3. It was explained that layer interfaces due to the introduction of PEO layer act as the permselective media and are responsible for the higher H-2/N-2 ideal separation factor which has exceeded the intrinsic permselectivities of the three polymers used in this study. (c) 2005 Elsevier B.V. All rights reserved.

纳秒激光诱导C60分子碎裂中轻碎片离子C+n(n＜30)的产生机理研究

The time of flight mass spectrometric technique was used to determine the initial mean kinetic energy of small fragment ions C-n(+) (n <= 11) produced from C-60 excited by 532 nm nanosecond laser pulses. The measured kinetic energy shows little variation with the fragment mass and the laser fluence in a broad range. Based on the assumption that C-30(+) is produced predominantly by a single electron emission followed by successive C-2 evaporation from hot C-60 in the nanosecond laser field, the formation of small fragments is interpreted as the complete breakup of the unstable C-30(+) cage structure. The interpretation is consistent with the previously observed results.

Determination of 30 free fatty acids in two famous Tibetan medicines by HPLC with fluorescence detection and mass spectrometric identification

A simple and sensitive high-performance liquid chromatographic (HPLC) method with fluorescence detection and mass spectrometric identification has been developed for analysis of 30 long-chain and short-chain free Fatty acids (FFAs). The fatty acids were derivatized to their esters with 1-[2-(p-toluenesulfonate)ethyl]-2-phenylimidazole-[4,5-f]-9,10-phenanthrene (TSPP) in N,N-dimethylformamide (DMF) at 90 degrees C with anhydrous K2CO3 as catalyst. A mixture Of C-1-C-30 fatty acids was completely separated within 60 min by gradient elution on a reversed-phase C-8 column. Qualitative identification of the acids was performed by atmospheric-pressure chemical ionization mass spectrometry (APCI-MS) in positive-ion mode. The fluorescence excitation and emission wavelengths were 260 and 380 nm, respectively. Quantitative determination of the 30 acids in two Tibetan medicines Gentiana straminea and G. dahurica was performed. The results indicated that the medicines contained many FFAs. Linear correlation coefficients for the FFA derivatives were > 0.9991. Relative standard deviations (RSDs, n = 6) for the fatty acid derivatives were < 3%. Detection limits (at a signal-to-noise ratio of 3:1) were 3.1-38 fmol. When the fatty acid derivatives were determined in the two real samples results were satisfactory and the sensitivity and reproducibility of the method were good.

Femtosecond optical Kerr effect study of Ge(10)AS(40)S(30)Se(20) film

The results of the femtosecond optical heterodyne detection of optical Kerr effect at 805 nm with the 80 fs ultrafast pulses in amorphous Ge10As40S30Se20 film is reported in this paper. The film shows an optical non-linear response of: 200 fs under ultrafast 80 fs-pulse excitation and the values of real and imaginary parts of non-linear susceptibility chi((3)) were 9.0 X 10(-12) and -4.0 X 10(-12) esu, respectively. The large third-order non-linearity and ultrafast response are attributed to the ultrafast distortion of the electron orbits surrounding the average positions of the nucleus of Ge, As, S and Se atoms. This Ge10As40S30Se20 chalcogenide glass would be expected as a promising material for optical switching technique. (c) 2005 Elsevier Ltd. All rights reserved.

四川地区出土古玻璃的质子激发X荧光分析

abstract {Proton induced X-ray emission (PIXE) technique is an effective method for the chemical composition analysis of ancient glass samples without destruction. Chemical composition of the ancient glass samples dated from the Warring States Period (770-476 B.C.) to the Six Dynasties Period (220-589 A.D.), which were unearthed in Sichuan area, was quantitatively determined by the PIXE technique. The results show that the glass Bi (disc) and the glass eye beads of the Warring States Period all belong to the PbO-BaO-SiO₂ system. According to the composition and shape, we infer that these glass Bi and eye beads were made in China. Whereas, the chemical compositions of the glass ear pendants and beads of the Six Dynasties Period are varied, including K₂O-CaO-SiO₂, K₂O-SiO₂ and other glass systems. Based on the obtained results and those from literatures, some questions related to the technical propagation of the ancient Chinese glass are discussed.}

α-Al_2O_3:C晶体的热释光和光释光特性

以高纯α-Al2O3和石墨为原料,采用温梯法生长了α-Al2O3:C晶体,使用RisΦTL/OSL-DA-15型热释光和光释光仪研究了其热释光和光释光特性.α-Al2O3:C晶体在462K附近有单一热释光峰,发射波长位于410nm.随着辐照剂量的增加,热释光强度逐渐增强,462K的热释光特征峰位置保持不变.α-Al2O3:C晶体的光释光衰减曲线由快衰减和慢衰减两个部分组成,随着辐照剂量的增加,快衰减部分衰减速率变化不大,而慢衰减部分衰减速率加快.在5×10-6—10Gy剂量范围内,α-Al2O3:C晶体的热释光剂量响应呈现良好的线性关系,30Gy时达到饱和;光释光剂量响应在5×10-6—60Gy剂量范围内呈现良好的线性关系,100Gy时达到饱和.与热释光相比,光释光剂量响应具有更高的灵敏度和更宽的线性剂量响应范围.

Identification of a gene, ccr-1 (sll1242), required for chill-light tolerance and growth at 15 degrees C in Synechocystis sp PCC 6803

Synechocystis sp. PCC 6803 exposed to chill (5 degrees C)-light (100 mu mol photons m(-2) s(-1)) stress loses its ability to reinitiate growth. From a random insertion mutant library of Synechocystis sp. PCC 6803, a sll1242 mutant showing increased sensitivity to chill plus light was isolated. Mutant reconstruction and complementation with the wild-type gene confirmed the role of sll1242 in maintaining chill-light tolerance. At 15 degrees C, the autotrophic and mixotrophic growth of the mutant were both inhibited, paralleled by decreased photosynthetic activity. The expression of sll1242 was upregulated in Synechocystis sp. PCC 6803 after transfer from 30 to 15 degrees C at a photosynthetic photon flux density of 30 mu mol photons m(-2) S-1. sll1242, named ccr (cyanobacterial cold resistance gene)- 1, may be required for cold acclimation of cyanobacteria in light.

mc-Si : H/c-Si solar cell prepared by PECVD

Hetero-junction solar cells with an me-Si: H window layer were achieved. The open voltage is increased while short current is decreased with increasing the mc-Si:H layer's thickness of emitter layer. The highest of V-oc of 597 mV has obtained. When fixed the thickness of 30 nm, changing the N type from amorphous silicon layer to micro-crystalline layer, the efficiency of the hetero-junction solar cells is increased. Although the hydrogen etching before deposition enables the c-Si substrates to become rough by AFM images, it enhances the formation of epitaxial-like micro-crystalline silicon and better parameters of solar cell can be obtained by implying this process. The best result of efficiency is 13.86% with the V-oc of 549.8 mV, J(sc) of 32.19 mA center dot cm(-2) and the cell's area of 1 cm(2).

The role of Sb in the molecular beam epitaxy growth of 1.30-1.55 mu m wavelength GaInNAs/GaAs quantum well with high indium content

Sb-assisted GaInNAs/GaAs quantum wells (QWs) with high (42.5%) indium content were investigated systematically. Transmission electron microscopy, reflection high-energy electron diffraction and photoluminescence (PL) measurements reveal that Sb acts as a surfactant to suppress three-dimensional growth. The improvement in the 1.55 mu m range is much more apparent than that in the 1.3 mu m range.. which can be attributed to the difference in N composition. The PL intensity and the full-width at half maximum of the 1.55 mu m single-QW were comparable with that of the 1.3 Am QWs. (c) 2006 Elsevier B.V. All rights reserved.

Room temperature (34 degrees C) operation of strain-compensated quantum cascade lasers

A short wavelength (lambda similar or equal to 3.5 mu m) strain-compensated InxGa(1-x)As/InyAl(1-y)As quantum cascade laser is reported. Quasi-continuous wave operation of this device at 34 degrees C with an output power of 11.4mW persisted for more than 30 minutes without obvious degradation. A very low threshold current density of 1.2KA/cm(2) at this temperature was observed.

Analysis of the interfaces of [NiFe/Mo](30) and [Fe/Mo](30) multilayers

The interface states of [NiFe/Mo](30) and [Fe/Mo](30) multilayers have been investigated by x-ray small angle reflection and diffuse scattering. Significant interface roughness correlation was observed in both ultrathin [NiFe/Mo](30) and [Fe/Mo](30) multilayers. An uncorrelated roughness of about 27-3.1 Angstrom was revealed in the [NiPe/Mo](30) multilayers, which is explained as originating from a transition layer between the NiFe and the Mo layers. By the technique of diffuse scattering, it is clearly indicated that the interfacial roughness of NiFe/Mo is much smaller than that of Fe/Mo although the lattice mismatch is the same in both multilayers.

Study on the hydrolysis/precipitation behavior of Keggin Al-13 and Al-30 polymers in polyaluminum solutions

The hydrolysis/precipitation behaviors of Al3+, Al-13 and Al-30 under conditions typical for flocculation in water treatment were investigated by studying the particulates' size development, charge characteristics, chemical species and speciation transformation of coagulant hydrolysis precipitates. The optimal pH conditions for hydrolysis precipitates formation for AlCl3, PAC(A113) and PAC(A130) were 6.5-7.5, 8.5-9.5, and 7.5-9.5, respectively. The precipitates' formation rate increased with the increase in dosage, and the relative rates were AlCl3 >> PAC(A130) > PACA113. The precipitates' size increased when the dosage increased from 50 mu M to 200 mu M, but it decreased when the dosage increased to 800 AM. The Zeta potential of coagulant hydrolysis precipitates decreased with the increase in pH for the three coagulants. The isoelectric points of the freshly formed precipitates for AlCl3, PAC(A113) and PAC(A130) were 7.3, 9.6 and 9.2, respectively. The Zeta potentials of AlCl3 hydrolysis precipitates were lower than those of PAC(A113) and PAC(A130) when pH > 5.0. The Zeta potential of PAC(A130) hydrolysis precipitates was higher than that of PACA113 at the acidic side, but lower at the alkaline side. The dosage had no obvious effect on the Zeta potential of hydrolysis precipitates under fixed pH conditions. The increase in Zeta potential with the increase in dosage under uncontrolled pH conditions was due to the pH depression caused by coagulant addition. Al-Ferron research indicated that the hydrolysis precipitates of AlCl3 were composed of amorphous AI(OH)3 precipitates, but those of PACA113 and PACA130 were composed of aggregates of Al-13 and Al-30, respectively. Al3+ was the most un-stable species in coagulants, and its hydrolysis was remarkably influenced by solution pH. Al-13 and Al-30 species were very stable, and solution pH and aging had little effect on the chemical species of their hydrolysis products. The research method involving coagulant hydrolysis precipitates based on Al-Ferron reaction kinetics was studied in detail. The Al species classification based on complex reaction kinetic of hydrolysis precipitates and Ferron reagent was different from that measured in a conventional coagulant assay using the Al--Ferron method. The chemical composition of Al-a, Al-b and Al-c depended on coagulant and solution pH. The Al-b measured in the current case was different from Keggin Al-13, and the high Alb content in the AlCl3 hydrolysis precipitates could not used as testimony that most of the Al3+ Was converted to highly charged Al-13 species during AlCl3 coagulation.

On the acid-base stability of Keggin Al-13 and Al-30 polymers in polyaluminum coagulants

The acid-base stabilities of Al-13 and Al-30 in polyaluminum coagulants during aging and after dosing into water were studied systematically using batch and flow-through acid-base titration experiments. The acid decomposition rates of both Al-13 and Al-30 increase rapidly with the decrease in solution pH. The acid decompositions of Al-13 and Al-30 with respect to H+ concentration are composed of two parallel first-order and second-order reactions, and the reaction orders are 1.169 and 1.005, respectively. The acid decomposition rates of Al-13 and Al-30 increase slightly when the temperature increases from 20 to ca. 35 A degrees C, but decrease when the temperature increases further. Al-30 is more stable than Al-13 in acidic solution, and the stability difference increases as the pH decreases. Al-30 is more possible to become the dominant species in polyaluminum coagulants than Al-13. The acid catalyzed decomposition and followed by recrystallization to form bayerite is one of the main processes that are responsible for the decrease of Al-13 and Al-30 in polyaluminum coagulants during storage. The deprotonation and polymerization of Al-13 and Al-30 depend on solution pH. The hydrolysis products are positively charged, and consist mainly of repeated Al-13 and Al-30 units rather than amorphous Al(OH)(3) precipitates. Al-30 is less stable than Al-13 upon alkaline hydrolysis. Al-13 is stable at pH < 5.9, while Al-30 lose one proton at the pH 4.6-5.75. Al-13 and Al-30 lose respective 5 and 10 protons and form [Al-13] (n) and [Al-30] (n) clusters within the pH region of 5.9-6.25 and 5.75-6.65, respectively. This indicates that Al-30 is easier to aggregate than Al-13 at the acidic side, but [Al-13] (n) is much easier to convert to Alsol-gel than [Al-30] (n) . Al-30 possesses better characteristics than Al-13 when used as coagulant because the hydrolysis products of Al-30 possess higher charges than that of Al-13, and [Al-30] (n) clusters exist within a wider pH range.

酚酞型聚芳醚砜共聚物与共混物－(PP/BiS-T) PES共聚物和(PPS/PES-C)、(PPO/PES-C)共混物的合成、结构与性能研究

本工作旨在通过共聚、共混技术制备酚酞型聚芳醚砜共聚物(PP/BiS-T) PES和共混物(PPS/PES-C)、PPO/PES-C，以便改善酚酞型聚芳醚砜（PES－C）的加工性能（特别是注射加工性能）和耐溶剂性能。通过研究共聚物和共混物的微观结构，聚集态结构与性能的关系，探索改善酚酞型聚芳醚硕性能的有效途径第一部分：(PP/BiS-T) PES共聚物的合成、结构与性能(PP/BiS-T) PES共聚物是以4，4'二氯二苯砜（DCDPS）、酚酞（PP）和4，4'－二羟基二苯硫醚(BiS-T)为单体，采用固体无水K_2CO_3/NMP/TMSO_2 混合溶剂反应体系合成的。共聚反应规律研究表明：在NMP/TMSO_2混合溶剂中，共聚反应可以顺利进行，避免了交联反应的发生，并成功地合成了高分子量的(PP/BiS-T) PES共聚物。DSC分析结果表明(PP/BiS-T) PES系列属于无定形的均相共聚物体系，每一组成比例对应的共聚物只具有一个玻璃化转变温度。且随组成比例的改变呈线性变化，TBA分析结果与DSC基本一致，并证实了(PP/BiS-T) PES属于均相共聚物体系，而不是均聚物的共混物。TG分析表明：共聚物具有良好的耐热氧化稳定性BiS-T链节在分子链中起到了提高自身抗氧性的作用。1R光谱对共聚物的结构进行表征。~(13)C-NMR分析确认共聚物多属于无规共聚物。动态力学试验表明共聚物(PP/BiS-T) PES以及PES－C，在－100 ℃附近和0－100 ℃，存在着次级松驰与转变，并发现水分子的存在对这种转变（次级松驰）有一定的影响。共聚物的熔融流动性试验和溶解性试验表明共聚物(PP/BiS-T) PES具有稍好于PES－C的熔融流动性；溶解性与PES－C类似。力学试验说明共聚物属于强而硬类型的聚合物。第二部分：PPS/PES－C共混物的制备、聚集态结构与性能PPS/PES－C共混物是以联苯/二苯硕混合物为溶剂，采用溶液沉析方法制备的，DSC、WAXD，SEM和1R分析手段对共混物的聚集态结构和微观结构进行了表征。DSC分析认为共混物属于多相体系，PPS的结晶性随着PES－C含量增加而降低。DSC和SEM观察结果表明：相转变发生在PPS占40％左右。PPS占25％时，DSC曲线呈现出界面相玻璃化转变温度。共混物具有良好的耐热氧化稳定性和耐热分解稳定性。微晶大小计算结果：PES－C存在导致了PPS微晶大小降低。WAXD曲线表明PPS占50％，共混物中的PPS具有较好的结晶性。SEM观察发现：随着PES－C含量增加，PES－C由分散相（PES－C50％）变为连续相（PES－C70％）。PPS占50％或低于50％时，共混物体系不仅发生了微观相分离，而且发生了宏观相分离。M.I.指数表明共混物中PPS为连续相时，共混物具有良好的熔融流动性。溶解性试验结果：共混物具有较好的耐溶剂性。第三部分：PPO/PES－C共混物的合成、结构与性能 PPO/PES－C共混物系用溶液－涂膜法，以氯彷为溶剂制备的。讨论了由同一共混物溶液浓度下制备的共混物的互溶性随组成的改变而变化。DSC分析结果：PPO/PES－C属于部分相溶性体系。利用Fox方程推导式计算结果表明PPO在富PES－C相中具有良好的分散性；而PES－C在富PPO相中的分散性较差。共混物(PPO/PES－C)试样经丙酮浸泡后，PPO（>50％）发生了溶剂诱导结晶现象，同时丙酮促使共混物发生完全相分离。结晶溶化热显示共混物中少量的PES－C存在有利于PPO的溶剂诱导结晶。TG分析表明共混物具有良好的耐热分解稳定性和耐热氧化分解稳定性。偏光显微镜下观察到PPO球晶的存在。SEM和FT－1R分别对共混物的形态结构和微观结构进行了表征。WAXD试验证实了丙酮处理的(PPO/PES－C)（70/30），（90/10）共混物中PPO的结晶性。溶解性试验表明：PPO掺入有助于 PES－C的耐溶剂性提高。