Preparation of a novel polysulfone/polyethylene oxide/silicone rubber multilayer composite membrane for hydrogen-nitrogen separation

A novel poly sulfone/polyethylene oxide/silicone rubber (PSOPEO/SR) multilayer composite membrane was fabricated by double coating polysulfone substrate membrane with polyethylene oxide and silicone rubber. Gas permeation experiments were performed at 30 degrees C for hydrogen and nitrogen. PSf(PEO/SR membrane displayed high and steady performance for H-2/N-2: permeances of H-2 and N-2 of 49.51 and 0.601 GPU, respectively, and H-2/N-2 ideal separation factor of 82.3. It was explained that layer interfaces due to the introduction of PEO layer act as the permselective media and are responsible for the higher H-2/N-2 ideal separation factor which has exceeded the intrinsic permselectivities of the three polymers used in this study. (c) 2005 Elsevier B.V. All rights reserved.

Comparison-speed liquid jets

The performance of a small high-speed liquid jet apparatus is described. Water jets with velocities from 200 to 700 m/s were obtained by firing a deformable lead slug from an air rifle into a stainless steel nozzle containing water sealed with a rubber diaphragm. Nozzle devices using the impact extrusion (IE) and cumulation (CU) methods were designed to generate the jets. The effect of the nozzle diameter and the downstream distance on the jet velocity is examined. The injection sequences are visualized using both shadowgraphy and schlieren photography. The difference between the IE and CU methods of jet generation is found.

Performance of a small high-speed liquid jet apparatus

The performance of a small high-speed liquid jet apparatus is described. Water jets of 200m/s to 700m/s have been obtained by firing a deformable lead slug from an air rifle into a stainless steel nozzle containing water sealed with a rubber diaphragm. Nozzle devices of using the impact extrusion (IE) method and cumulation (CU) method are designed to generate jets. The injection sequences are visualized using schlieren photography. The difference between the IE and CU methods in the jet generation is found.

Deformation Of Pdms Membrane And Microcantilever By A Water Droplet: Comparison Between Mooney-Rivlin And Linear Elastic Constitutive Models

In this paper, we studied the role of vertical component Of Surface tension of a water droplet on the deformation of membranes and microcantilevers (MCLs) widely used in lab-on-a-chip and micro-and nano-electromechanical system (MEMS/NEMS). Firstly, a membrane made of a rubber-like material, poly(dimethylsiloxane) (PDMS), was considered. The deformation was investigated using the Mooney-Rivlin (MR) model and the linear elastic constitutive relation, respectively. By comparison between the numerical solutions with two different models, we found that the simple linear elastic model is accurate enough to describe such kind of problem, which would be quite convenient for engineering applications. Furthermore, based on small-deflection beam theory, the effect of a liquid droplet on the deflection of a MCL was also studied. The free-end deflection of the MCL was investigated by considering different cases like a cylindrical droplet, a spherical droplet centered on the MCL and a spherical droplet arbitrarily positioned on the MCL. Numerical simulations demonstrated that the deflection might not be neglected, and showed good agreement with our theoretical analyses. (C) 2008 Elsevier Inc. All rights reserved.

土地利用变化对西双版纳地区土壤及植被碳含量的影响

土地利用变化，尤其是热带地区森林生态系统土地利用方式的变化极大地改变了全球碳循环，对大气CO2浓度的升高，气候变暖等全球性环境问题起着不可忽视的作用。同时，森林的大面积破坏，引起土壤流失，营养元素含量降低，土壤健康状况恶化，最终大幅度降低生态系统的生产力。本文主要结合野外实地调查和室内分析的方法，研究森林砍伐后转变为农田和橡胶园对西双版纳热带地区土壤碳、氮、磷含量以及有机质化学结构的影响，天然次生林恢复、橡胶园建设对大气CO2的蓄积作用。 森林砍伐后转变为农田和橡胶园，显著地改变了土壤的理化特性。研究结果表明，与次生林相比，农田和橡胶园表层土壤容重、pH值升高，含水量降低，有机质、全氮、全磷、速效氮、有效磷含量显著降低。土地利用变化对土壤特性的影响主要发生在0-40 cm 表层土壤，而对40 cm以下土层影响较小。 土地利用变化改变土壤碳含量，同时影响土壤有机质的化学结构。胡敏酸紫外-可见光谱(UV-VIS)、傅利叶变换红外光谱 (FT-IR) 分析发现，不同生态系统表层土壤 (0-20 cm) 胡敏酸光谱学特性存在明显差异。次生林E4/E6值高于农田和橡胶园。与次生林相比，农田和橡胶园表层土壤有机质中酚基相对含量显著降低，脂肪族、芳香族、羧基以及多聚糖等化合物相对含量增加。 运用样地调查、生物量模型模拟和室内土壤样品分析方法，研究了次生林恢复和橡胶园建设对大气CO2的汇集作用。结果表明：退化土壤恢复为次生林、农田建设橡胶园能够有效促进植被和土壤中碳的汇集。次生林和橡胶林生物量增长速率分别为9.8，10.2 （9.4）t•ha-1•yr-1, 1 m表层土壤有机碳汇集速率分别为0.7和1.1 t•C•ha-1•yr-1。模拟结果显示，40年橡胶林生物量为327 (324) t•ha-1, 恢复50年后天然次生林生物量为395 t•ha-1。加之土壤有机碳，40年橡胶园约汇集碳190 t•ha-1, 次生林恢复50年碳汇集潜力为250 t•ha-1。

Fiber Bragg grating hydrophone with high sensitivity

A fiber Bragg grating (FBG) hydrophone with high sensitivity was demonstrated. This hydrophone used a rubber diaphragm and a copper hard core as the sensing element. To compensate the hydrostatic pressure, a capillary tube was fixed at the end of the hydrophone. Theoretical analysis of the acoustic pressure sensitivity was given in this letter. Experiments were carried out to test the frequency response of the hydrophone. The result shows that when the Young's modulus of the diaphragm is higher, a flatter frequency response will be obtained.

Vacuum pyrolysis of waste tires with basic additives

Granules of waste tires were pyrolyzed tinder vacuum (3.5-10 kPa) conditions, and the effects of temperature and basic additives (Na2CO3, NaOH) on the properties of pyrolysis were thoroughly investigated. It was obvious that with or without basic additives, pyrolysis oil yield increased gradually to a maximum and subsequently decreased with a temperature increase from 450 degrees C to 600 degrees C, irrespective of the addition of basic additives to the reactor. The addition of NaOH facilitated pyrolysis dramatically, as a maximal pyrolysis oil yield of about 48 wt% was achieved at 550 degrees C without the addition of basic additives, while a maximal pyrolysis oil yield of about 50 wt% was achieved at 480 degrees C by adding 3 wt% (w/w, powder/waste tire granules) of NaOH powder. The composition analysis of pyrolytic naphtha (i.b.p. (initial boiling point) similar to 205 degrees C) distilled from pyrolysis oil showed that more dl-limonene was obtained with basic additives and the maximal content of dl-limonene in pyrolysis oil was 12.39 wt% which is a valuable and widely-used fine chemical. However, no improvement in pyrolysis was observed with Na2CO3 addition. Pyrolysis gas was mainly composed of H-2, CO, CH4, CO2, C2H4 and C2H6. Pyrolytic char had a surface area comparable to commercial carbon black, but its proportion of ash (above 11.5 wt%) was much higher.

聚苯乙烯-聚丁二烯嵌段共聚物反转相行为的研究

本论文以聚苯乙烯（PS）一聚丁二烯（PB）三嵌段和二嵌段共聚物体系为研究对象，利用聚合物的软有序化，控制聚合物分子链的取向和聚集条件，系统地考察了嵌段共聚物在由溶液成膜的过程中动力学效应和墒效应对其相结构和相转变行为的影响。并探讨了不同相结构和其力学性能之间的构效关系。设计了聚苯乙烯（PS）一聚丁二烯（PB）（PS≈30wt％）／非选择性溶剂体系，通过改变溶剂的挥发速率，控制了嵌段共聚物薄膜相结构形成的动力学过程。在快速挥发的条件下，在嵌段共聚物中观察到了特殊的反转相结构，即共聚物中含量多的组分（PB）形成了分散相，而当溶剂挥发很慢的条件下，得到的是热力学较稳定的正常相的结构。对不同分子量的一系列嵌段共聚物的研究表明，反转相的形成和分子量相关，与聚合物的链段数目无关，只有在低于临界分子量 （Mw=70-100 KDa）的嵌段共聚物中，成膜过程的动力学过程才影响嵌段共聚物薄膜的最终相态，即形成反转相。这种依赖于分子量的相转变行为，揭示了分子链运动速度与环境变化速率的匹配对嵌段共聚物薄膜有序相结构形成的重要作用，即动力学效应对聚合物软有序化的重要作用。利用冷冻干燥的方法，进一步研究了嵌段共聚物在极慢的溶剂挥发下，由溶液膜变成固体膜的过程中，随着溶液浓度的增加，不同聚合物分子链在溶液中自组织形成有序结构的过程。结果表明反转相是由稀溶液向亚浓溶液转变的过程中形成的。通过选取具有代表性的不同亲和性的溶剂：苯和环己烷及其混合溶剂，研究了溶剂对不同链段亲和性的差异对反转相形成的影响。由聚合物一溶剂相互作用参数判断，苯是体系的良溶剂，环己烷是体系的。溶剂，而苯对PS链段有较好的亲和性，与之相反环己烷对PB链段有较好的亲和性，通过对聚苯乙烯（PS）一聚丁二烯印B）二嵌段共聚物在苯和环己烷极其混合溶剂中的相转变行为的研究发现，随着溶剂对含量少的PS链段亲和性的降低，反转相不再出现。这是由于苯与PS．链段、环己烷与PB链段有更好的亲和性，嵌段共聚物在稀溶液中，在耗尽吸引的（depletion attraction）作用下，与溶剂亲和性弱的链段，在溶液中优先发生聚集，而有序聚集后导致的混合熵的损失会被更多的因有序聚集后小分子自由体积增加引起的平移嫡的增量所补偿，因此导致了嫡驱动的软有序化。最后，通过原子力显微镜纳米压印法，分别对反转相和正常相结构的纳米力学性能进行了对比研究，讨论了不同相结构间模量的差异，结果表明软段（PB）形成分散相结构时薄膜的模量总是小于硬段（PS）形成分散相结构时薄膜的模量，这主要是由嵌段共聚物不同组分的相对含量及形成的相的结构决定的。

Thermoplastic Elastomers Based on Compatibilized Poly(butylene terephthalate) Blends: Effect of Functional Groups and Dynamic Curing

Two sets of graft copolymers were prepared by grafting glycidyl methacrylate (GMA) or ally] (3-isocyanate-4-tolyl) carbamate (TAI) onto ethylene/propylene/diene terpolymer (EPDM) in an internal mixer. These graft copolymers were used as the compatibilizer to prepare the thermoplastic elastomers (TPEs) containing 50 wt%, of poly(butylene terephthalate), PBT, 30 wt% of compatibilizer, and 20 wt% of nitrile-butadiene rubber, NBR. The indirect, two-step mixer process was chosen for dynamic curing.

Critical behavior of brittle-ductile transition of polymers

We report that the brittle-ductile transition of polymers induced by temperature exhibits critical behavior. When t close to 0, the critical surface to surface interparticle distance (IDc) follows the scaling law: IDc proportional to t(-v) where t = 1 - T/T-BD(m) (T and T-BD(m) are the test temperature and brittle-ductile transition temperature of matrix polymer, respectively) and v = 2/D. It is clear that the scaling exponent v only depends on dimension (D). For 2, 3, and 4 dimension, v = 1, 2/3, and 1/2 respectively. The result indicates that the ID, follows the same scaling law as that of the correlation length (xi), when t approach to zero.

Effect of the nature of annealing solvent on the morphology of diblock copolymer blend thin films

The morphologies and structures for the thin film of blend systems consisting of two asymmetric polystyrene-block-polybutadiene (SB) diblock copolymers induced by annealing in the vapor of different solvents, namely, cyclohexane, benzene, and heptane, which have different selectivity or preferential affinity for a certain block, were investigated by tapping mode atomic force microscopy (AFM) and transmission electron microscopy (TEM). The results revealed that even a slight preferential affinity of good solvent for one block would strongly alter the morphology of the blend thin film.

Living polymerization of 1,3-butadiene by a Ziegler-Natta type catalyst composed of iron(III) 2-ethylhexanoate, triisobutylaluminum and diethyl phosphite

Living characteristics of facilely prepared Ziegler-Natta type catalyst system consisting of iron(III) 2-ethylhexanoate, triisobutylaluminum and diethyl phosphite have been found in the polymerization of 1,3-butadiene in hexane at 40 degrees C. The characteristics have been well demonstrated by: a first-order kinetics with respect to monomer conversion, a narrow molecular weight distribution (M-w/M-n = 1.48-1.52) of polybutadiene in the entire range of polymerization conversion and a good linearity between M-n and the yield of polymer. Feasible post-polymerization of 1,3-butadiene and block co-polymerization of 1,3-butadiene and isoprene further support the living natures of the catalyst bestowed with.

Metal dependent control of cis-/trans-1,4 regioselectivity in 1,3-butadiene polymerization catalyzed by transition metal complexes supported by 2,6-bis[1-(iminophenyl)ethyl]pyridine

Fe(III), Cr(III), Fe(II), Co(II) and Ni(II) chloride complexes supported by 2,6-bis[1-(iminophenyl)ethyl]pyridine have been synthesized and characterized along with single crystal X-ray diffraction. These complexes, in combination with MAO, have been examined in butadiene polymerization. The catalytic activity and regioselectivity are strongly controlled by metal center and cocatalyst (MAO/Co ratio dependent in the case of Co(II) complex). The activity decreases in the order of Fe(III) > Co(II) > Cr(III) approximate to Ni (II) complexes, in consistent with the space around the metal center. Polybutadiene with different microstructure content, from high trans-1,4 units (88-95% for iron(III) and Cr(III)), medium trans-1,4 and cis-1,4 units (55% and 35%, respectively, for iron(II)) to high cis-1,4 units 79% for Co(II) and 97% for Ni(II) call be easily achieved by varying of the metal center.