Covalent modification of a glassy carbon surface by 4-aminobenzoic acid and its application in fabrication of a polyoxometalates-consisting monolayer and multilayer films

4-Aminobenzoic acid (4-ABA) was covalently grafted on a glassy carbon electrode (GCE) by amine cation radical formation in the electrooxidation process of the amino-containing compound. X-ray photoelectron spectroscopy measurement proves the presence of 4-carboxylphenylamine monolayer on the GCE. The redox responses of various electroactive probes were investigated on the 4-ABA-modified GCE. Electron transfer to Fe(CN)(6)(3-) in solutions of various pHs was studied by both cyclic voltammetry and electrochemical impedance analysis on the modified electrode. Changes in the solution pH value result in the variation of the terminal group charge state, based on which surface pK(a) values are estimated. The 4-ABA-modified GCE was used as a suitable charged substrate to fabricate polyoxometalates-consisting (POM-consisting) monolayer and multilayer films through layer-by-layer assembly based on electrostatic attraction. Cyclic voltammetry shows the uniform growth of these three-dimensional multilayer films. Taking K10H3[Pr-(SiMo7W4O39)(2)]. H2O (abbreviated as Pr(SiMo7W4)(2)), for example, the preparation and electrochemical behavior of its monolayer and multilayer film had been investigated in detail. This modification strategy is proven to be a general one suitable for anchoring many kinds of POMs on the 4-ABA-modified GCE.

Electroluminescent properties of the Tris-(acetylsalicylate)-terbium (Tb(AS)(3))

The solubility of [Tris-(acetylsalicylate)-terbium] [Tb(AS)(3)] is improved to a greater extent than [Tris-(salicylate)-terbium] [Tb(Sal)(3)] following introduction of a flexible acetyl group. Th3+ binds with acetylsalicylate in solution at low pH value and the resultant Tb(AS)(3) has good solubility in chloroform. A Green EL device with the structure ITO/PVK/PVB:PBD: Tb(AS)(3)/ PBD/Al has been fabricated based on soluble Tb(AS)(3), in which Tb(AS)(3) was first used as an emissive center doped with PVK and PBD. The hole-transporting layer and the emissive layer were formed by spin coating. The device exhibited a highly pure characteristic green light of Tb3+. (C) 2001 Elsevier Science B.V. All rights reserved.

Electrocatalytic oxidation of ascorbic acid by ferrocene in lipid film cast on a glassy carbon electrode

A ferrocene-dimyristoyl phosphatidylcholine (DMPC) film electrode was prepared by casting the solution of ferrocene and DMPC in chloroform onto a glassy carbon electrode surface. Ferrocene retained in the biological membrane gave a couple of irreversible peaks of cyclic voltammogram. The electrode exhibited good electrocatalytic activity for the oxidation of ascorbic acid (H(2)A) in phosphate buffer (pH 6.64) with an anodic peak potential of +340 mV (vs. Ag/AgCl). The anodic current was directly proportional to the square root of the scan rate below 150 mV s(-1). The influence of the pH value was investigated and it was observed that pH 6.64 was the suitable value to the anodic peak potential and current. The thickness of the film and the interference of uric acid were also studied. The electrode can be used to determine H(2)A in the presence of equimolar uric acid. The catalytic peak current increased linearly with the concentration of H(2)A in the range of 1 X 10(-4)-5 X 10(-3) mol L-1.

Separation of promethazine and thioridazine using capillary electrophoresis with end-column amperometric detection

Promethazine and thioridazine were separated and detected by capillary electrophoresis with end-column amperometric detection. The influence of pH Value on oxidation potential, the peak current and the resolution were studied and the following conditions was selected: 0.03 M Na2HPO4 and 0.015 M citric acid at pH 3.0, detection potential at 1.10 V. The detection limits of these two substances were in the range of 10(-8) mol/l. The linear range spanned two to three orders of magnitude. This method was applied to the detection of promethazine and thioridazine spiked in urine. (C) 1999 Elsevier Science B.V. All rights reserved.

Redox reaction of disulfide polyaniline in aqueous solution

The cleavage and formation of the di sulfide bond of 2,5-dimercapto-1,3,4-thiadiazole (DMcT) were examined in an aqueous solution of pH value from 0 to 14 with and without polyaniline (PAn), The redox reaction of DMcT was accelerated by PAn in acidic condition. The cell using this anodic material was set-up and characterized in aqueous electrolyte.

Chlorination and oxidation of aromatic polyamides .2. Chlorination of some aromatic polyamides

The effects of chlorine on three kinds of aromatic polyamides: those not containing a substituent, those containing substituents, and those containing heterocyclic aromatic rings, were studied. The correlations between the chemical structures of polyamides and the reactivity to hypochlorous acid were examined by IR and C-13 solid-state NMR spectra before and after chlorination. It was found that the chlorination of polyamides depends not only on their chemical structures but also on chlorination conditions such as pH value and reaction time. Their response to chlorination corresponds to four types: ring-chlorination, no reaction, N-chlorination, and chain cleavage. (C) 1996 John Wiley & Sons, Inc.

Improvements in the selectivity of electrochemical detectors for liquid chromatography and flow injection analysis using the self-assembled n-alkanethiol monolayer-modified au electrode

4-Aminophenol (4-AP), paracetamol (PRCT), norepinephrine (NE), and dopamine (DA) (all somewhat hydrophobic compounds) were HPLC electrochemically detected while the signals from uric acid (UA) and ascorbic acid (AA) (both hydrophilic compounds at the pH studied) were minimized, taking advantage of the permselectivity of the self-assembled n-alkanethiol monolayer (C-10-SAM)-modified Au electrodes based on solute polarity, The effects of various factors, such as the chain length of the n-alkanethiol modifier, modifying time, and pH value, on the permeability of C-10-SAM coatings were examined, The calibration curves, linear response ranges, detection limits, and reproducibilities of the EC detector for 4-AP, PRCT, NE, and DA were obtained, The result shows that the EC detector can be applied in the chromatographic detection of 4-AP, PRCT, NE, and DA in urine, effectively removing the influence of UA and AA in high concentrations existing in biological samples. As a result, a great improvement in the selectivity of EC detectors has been achieved by using Au electrodes coated with neutral n-alkanethiol monolayer.

H-1 and C-13 NMR studies of TTHA complexes with diamagnetic rare earth ions

TTHA complexes with diamagnetic rare earth ions (La3+, Y3+ and LU(3+)) were studied by H-1 and C-13 NMR spectroscopy. A symmetric structural model was suggested for La(TTHA) complex and an asymmetric model for Y(TTHA) and Lu(TTHA) complexes. The complex formation was dependent on the pH value of the solution. The interactions of La(TTHA) with the additional metal ions (La3+, Y3+ and Ca2+) were relatively weak, but relatively strong for that of Lu(TTHA) with the additional Lu3+.

ELECTROCATALYTIC OXIDATION AND FLOW DETECTION OF CYSTEINE AT AN AQUOCOBALAMIN ADSORBED GLASSY-CARBON ELECTRODE

A chemically modified electrode (CME) constructed by adsorption of aquocobalamin (VB12a) onto a glassy carbon electrode surface was demonstrated to catalyze the electro-oxidation of cysteine, a sulfhydryl-containing compound. The sulfhydryl oxidation occured at 0.54-0.88 V vs. Ag/AgCl depending on pH value (3.0-10.0). The electrocatalytic behavior of cysteine is elucidated with respect to solution pH, operating potential and other variables as well as the CME preparation conditions. When used as the sensing electrode in flow injection amperometric detection, the CME permitted detection of the compound at 0.8 V. The detection limit was 1.7 pmol. The linear response range went up to 1.16 nmol. The stability of the CME was shown by RSD (4.2%) over 10 repeated injections.

SOLVENT-EXTRACTION OF TERBIUM(III,IV) PERIODATE COMPLEXES WITH QUATERNARY AMINE

The differences between the solvent extraction of Tb(III) and Tb(IV) periodate complexes with quaternary amine were studied carefully for the first time. The effects of extractant concentration, phase ratio, the pH value of stock solution, salting-out agent, extractant form, diluent, and extraction time were comprehensively investigated. Under optimal conditions the separation factor between Tb(IV) and Tb(III) periodate complexes is over 5.5.

ELECTROCATALYTIC OXIDATION OF ASCORBIC ACID AT POLYANILINE FILM MODIFIED GLASSY CARBON ELECTRODES

A conducting polyaniline (PAn) film modified glassy carbon (GC) electrode was prepared by electrochemical polymerization. The electrochemical behavior of ascorbic acid (AH(2)) in aqueous solution at this PAn modified electrode was studied in detail. The experimental results show that PAn film modified electrode has good electrocatalytic activity on the oxidation of ascorbic acid in aqueous solution over a wide range of pH value, among which pH 4 is the optimum condition. The oxidation process of ascorbic acid at PAn film electrode can be regarded as an EC catalytic mechanism. The kinetic process of the catalytic reaction was investigated by rotating disk electrode (RDE) coated with PAn films. The rate constant of the catalytic reaction was evaluated. The catalytic peak currents are proportional to the concentrations tions of ascorbic acid in the range of 5 x 10(-2)-1 x 10(-6) mol . L-1. The PAn film elec trodes give very stable responce for the oxidation of ascorbic acid. The present investigation shows the posibility of using PAn film modified electrode for the determination of ascorbic acid.

THE EFFECT OF FILM-FORMING CONDITIONS FOR TAPCUPC LANGMUIR-BLODGETT-FILMS ON MORPHOLOGY AND PROPERTIES

The dependence of morphology and properties on film-forming conditions is described for the symmetrically substituted copper tetra-4-(2, 4-di-t-amylphenoxy) phthalocyanine (tapCuPc) Langmuir-Blodgett (LB) films. The effects of LB film-forming conditions (such as the surface pressure, pH value and the concentrations of spreading solutions) on film quality were studied with the help of a UV-visible spectrophotometer and a transmission electron microscope. Transmission electron microscopy photographs of the surface morphology of tapCuPc LB films show that a smooth and homogeneous surface structure can be obtained under optimum film-forming conditions.

Effect of heavy metals (Cd, Cu) on the gametophytes of Laminaria japonica Aresch

Effects of various concentrations of two heavy metals, namely Cd and Cu, on gametophytes of Laminaria japonica Aresch were determined by recording morphological changes of gametophytes, determining pH values and the heavy metal content of the culture solution, calculating the germination rate of sporophytes, and observing heavy metal (Cd) distribution using a fluorescence microscope. The results showed that heavy metals damaged the gametophytes, and were even lethal, and that the higher the concentration of heavy metal ions, the greater the injury to gametophytes. Gametophytes could not survive in culture solutions containing more than 100 mg/L Cd and 50 mg/L Cu and were only able to survive in culture solution containing a mixture of Cd and Cu tip to a concentration of 10 mg/L, which indicates that gametophytes have a higher tolerance to Cd than Cu and that multiple heavy metal ions in solution markedly aggravate the damage to gametophytes compared with individual heavy metal ions. With increases in the concentration of the heavy metal, the burgeoning rate of sporophytes decreased acutely, and solutions containing multiple heavy metal ions caused even more marked harm to sporophytes than solutions containing a single heavy metal ion, because most sporophytes died in mixed solutions. The pH value of the culture medium dropped immediately at the beginning (the first day) of treatment, increased over the following days, and then decreased again. The pH of culture media containing multiple heavy metal ions showed greater variation than media containing a single heavy metal ion, with the extent of the decrease in pH of culture media containing multiple ions being greatest during the last period of the experiment. With increases in the concentration of heavy metals, the capacity of gametophytes to accumulate these ions increased. The blue fluorescent light emitted by the Cd- and Cd-binding protein complex existing in gametophytes in media containing different concentrations of Cd showed clearly the distribution of the ion in gametophytes and the results obtained were consistent with distribution determined using other methods. All results of the present study showed that gametophytes of L. japonica play a remarkable role as heavy metal decontaminators, especially with regard to Cd.

Formation and growth of Bryopsis hypnoides lamouroux regenerated from its protoplasts

Tissue culture, SDS-polyacrylamide gel electrophoresis (SDS-PAGE) and spectra analysis were used for studying the aggregation mechanism of protoplasts from Bryopsis hypnoides Lamouroux and the discrepancy between the protoplast-regenerated plants and the wild type. The aggregation of protoplasts from B. hypnoides was observed in natural seawater and artificial seawater with different pH values, and the location and mechanism of the materials causing the aggregation were also studied. Results showed that the protoplasts could aggregate into some viable spheres in natural seawater and subsequently grow into mature individuals. Aggregation of the protoplasts depended exclusively upon the pH value (6-11), and the protoplasts aggregated best at pH 8-9. Some of the extruded protoplasts were separated into two parts by centrifugation: the pellet (PO) and the supernatant (PL). The PO could aggregate in artificial seawater (pH 8.3) but not in PL. No aggregation was found in PO cultured in natural seawater containing nigericin, which can dissipate the proton gradients across the membrane. These experiments suggest that the aggregation of protoplasts is proton-gradient dependent and the materials causing the aggregation were not in the vacuolar sap, but located on the surface or inside the organelles. Furthermore, the transfer of the materials across the membrane was similar to Delta pH-based translocation (Delta pH/TAT) pathway that occurs in the chloroplasts of higher plants and bacteria. Obvious discrepancies in both the total soluble proteins and the ratio of chlorophyll a to chlorophyll b between the regenerated B. hypnoides and the wild type were found, which may be related to the exchange of genetic material during aggregation of the organelles. In the process of development, diatom Amphora coffeaeformis Agardh attached to the protoplast aggregations, retarding their further development, and once they were removed, the aggregations immediately germinated, which showed that diatoms can affect the development of other algae.

Fermentative hydrogen production by the new marine Pantoea agglomerans isolated from the mangrove sludge

A new fermentative hydrogen-producing bacterium was isolated from mangrove sludge and identified as Pantoea agglomerans using light microscopic examination, Biolog test and 16S rRNA gene sequence analysis. The isolated bacterium, designated as P. agglomerans BH-18, is a new strain that has never been optimized as a potential hydrogen-producing bacterium. In this study, the culture conditions and the hydrogen-producing ability of P. agglomerans BH-18 were examined. The strain was a salt-tolerant facultative anaerobe with the initial optimum pH value at 8.0-9.0 and temperature at 30 degrees C on cell growth. During fermentation, hydrogen started to evolve when cell growth entered late-exponential phase and was mainly produced in the stationary phase. The strain was able to produce hydrogen over a wide range of initial pH from 5 to 10, with an optimum initial pH of 6. The level of hydrogen production was affected by the initial glucose concentration, and the optimum value was found to be 10 g glucose/l. The maximum hydrogen-producing yield (2246 ml/l) and overall hydrogen production rate (160 ml/l/h) were obtained at an initial glucose concentration of 10 g/l and an initial pH value of 7.2 in marine culture conditions. In particular, the level of hydrogen production was also affected by the salt concentration. Hydrogen production reached a higher level in fresh culture conditions than in marine ones. In marine conditions, hydrogen productivity was 108 ml/l/h at an initial glucose concentration of 20 g/l and pH value of 7.2, whereas, it increased by 27% in fresh conditions. In addition, this strain could produce hydrogen using glucose and many other carbon sources such as fructose, sucrose, sorbitol and so on. As a result, it is possible that P. agglomerans BH-18 is used for biohydrogen production and biological treatment of mariculture wastewater and marine organic waste. (C) 2008 International Association for Hydrogen Energy. Published by Elsevier Ltd. All rights reserved.