Enhancement of boron removal in treatment of spent rinse from a plating operation using RO

Boron removal is a critical issue in the production of drinking water and of ultra-pure water in the electronics industry. Boron rejection in a RO process is typically in the range of 40-60%. The objective of this study was to distinguish the factor contributing to enhanced boron rejection in reclamation of a spent rinse stream from a plating operation. The effects of different known components used in the feed on boron removal were investigated in the laboratory. The results indicated that glycolic acid and antifoulants could not individually enhance boron rejection in a RO process. A high boron rejection of 95% was achieved as the concentration of iron in the feed was 10 times higher than that of boron, which might be due to formation of a complex between iron oxide and boron. The finding was confirmed in a pilot study.

非饱和土中镉离子传输模型参数反演

使用自行设计的的真空实验装置,采用一维实验室土柱实验方法在不同实验条件下进行了15组实验,并基于实验所得的穿透曲线,使用梯度正则化方法反演得到了镉离子在8种葡萄牙土样和1种比利时土样中相应的传输模型参数.同时通过数值模拟实验验证了梯度正则化方法的有效性和可靠性,进而证明所得结果是有效的.

Characterising Of Internal Stresses In Duplex Coating By Fem

The internal stresses in a duplex coating involving a prequenched layer are believed to change if it is exposed to thermal loading. To characterise the internal stresses in such a duplex coating, a gradient model of finite element method is set up. The initial stress within the substrate developed in as quenching and the internal stresses due to the tempering of the prequenched layer ( TPQL) in such a duplex coating are calculated. The synthetical internal stresses in coating can be estimated by superposing uniform initial stresses developed during plating. The results indicate that the residual tensile stresses due to fabrication in coating will be decreased greatly, or even synthetical compressive internal stresses may arise in the coating.

Preparation And Optical Properties Of Cdte/Cdo Center Dot Nh(2)O Core/Shell Nano-Composites In Aqueous Solution

The deposition of CdO center dot nH(2)O On CdTe nanoparticles was studied in an aqueous phase. The CdTe nanocrystals (NCs) were prepared in aqueous solution through the reaction between Cd2+ and NaHTe in the presence of thioglycolic acid as a stabilizer. The molar ratio of the Cd2+ to Te2- in the precursory solution played an important role in the photoluminescence of the ultimate CdTe NCs. The strongest photoluminescence was obtained under 4.0 of [Cd2+]/[Te2-] at pH similar to 8.2. With the optimum dosage of Cd(II) hydrous oxide deposited on the CdTe NCs, the photoluminescence was enhanced greatly. The photoluminescence of these nanocomposites was kept constant in the pH range of 8.0-10.0, but dramatically decreased with an obvious blue-shifted peak while the pH was below 8.0. In addition, the photochemical oxidation of CdTe NCs with cadmium hydrous oxide deposition was markedly inhibited.

Characteristics of the interface of a laser-quenched steel substrate and chromium electroplate

The interface of a laser-discrete-quenched steel substrate and as-deposited chromium electroplate was investigated by ion beam etching, dissolving-substrate-away and using a Vickers microhardness tester, in an attempt to reveal the mechanism that the service life of the chromium-coated parts is increased by the duplex technique of laser pre-quenching plus chromium post-depositing. The laser quenching of the steel substrate can reduce the steep hardness gradient at the substrate/chromium interface and improve the load-bearing capacity of chromium electroplate. Moreover, the laser quenching prior to plating has an extremely great effect on the morphologies and microstructure of the substrate/chromium interface: there is a transient interlayer at the original substrate/chromium interface while there is not at the laser-quenchedzone/chromium interface; the near-substrate surface microstructure and morphologies of the free-standing chromium electrodeposits, whose substrate was dissolved away with nital 30% in volume, inherit the periodically gradient characteristics of the laser-discrete-quenched substrate surface. (c) 2006 Elsevier B.V. All rights reserved.

测量镀铬层界面韧性的激光屈曲法

为了测量强界面电镀铬层的界面韧性，利用连续CO_2激光器对钢基体上的电镀铬层表面进行循环扫描实验。结果表明：该种加热方式能够诱发铬层沿激光扫描方向呈周期性分布的屈曲变形。在此基础上，结合涂层屈曲变形理论，提出测量镀铬层界面韧性的激光屈曲法。该方法只需对一个屈曲单元的最大屈曲高度和屈曲半长进行测量，就可给出界面韧性。作为应用举例，利用该方法对上述镀铬层／钢基体结构界面韧性进行了测量。

电弧离子镀薄膜中的颗粒尺寸及其影响的扫描电镜观察

用扫描电镜对比分析了电弧离子镀增加直线磁场过滤对沉积TiN和TiAlN薄膜中颗粒的密度和尺寸的影响，，结果表明，TIN薄膜中颗粒的最大直径，从14μm减小到3μm，颗粒密度从lO~9／cm~2。降低到10~5／cm~2.TilN薄膜由于靶材中含有低熔点金属Al，因而发射出更大的颗粒，有的颗粒集团达到20μm，磁场过滤后颗粒尺寸减小，颗粒密度降低到10~6／cm~2。分析了脉冲叠加直流偏压对TiCrZrN复合薄膜相组成的影响。颗粒可使电弧离子镀rriN／crN多层膜的结合力降低，并使针孔产生遗传。使用直线型磁场过滤及脉冲叠加直流偏压不仅使颗粒密度和尺寸显著降低和减小，而且多层化对小颗粒产生了包覆作用。

Preparation and optical properties of CdTe/CdO center dot nH(2)O core/shell nano-composites in aqueous solution

The deposition of CdO center dot nH(2)O On CdTe nanoparticles was studied in an aqueous phase. The CdTe nanocrystals (NCs) were prepared in aqueous solution through the reaction between Cd2+ and NaHTe in the presence of thioglycolic acid as a stabilizer. The molar ratio of the Cd2+ to Te2- in the precursory solution played an important role in the photoluminescence of the ultimate CdTe NCs. The strongest photoluminescence was obtained under 4.0 of [Cd2+]/[Te2-] at pH similar to 8.2. With the optimum dosage of Cd(II) hydrous oxide deposited on the CdTe NCs, the photoluminescence was enhanced greatly. The photoluminescence of these nanocomposites was kept constant in the pH range of 8.0-10.0, but dramatically decreased with an obvious blue-shifted peak while the pH was below 8.0. In addition, the photochemical oxidation of CdTe NCs with cadmium hydrous oxide deposition was markedly inhibited.

Electro-optic integration of embedded electrodes and waveguides in LiNbO3 using a femtosecond laser

We describe the fabrication of a Mach-Zehnder optical modulator in LiNbO3 by femtosecond laser micormachining, which is composed of optical waveguides inscripted by a femtosecond laser and embedded microelectrodes subsequently using femtosecond laser ablation and selective electroless plating. A half-wave voltage close to 19 V is achieved at a wavelength of 632.8 nm with an interaction length of 2.6 mm. This simple and cost-effective technique opens up new opportunities for fabricating integrated electro-optic devices. (C) 2008 Optical Society of America

Fabrication of microelectrodes deeply embedded in LiNbO3 using a femtosecond laser

We present a novel technique to fabricate deeply embedded microelectrodes in LiNbO3 using femtosecond pulsed laser ablation and selective electroless plating. The fabrication process mainly consists of four steps, which are (1) micromachining of microgrooves on the surface of LiNbO3 by femtosecond laser ablation; (2) formation of AgNO3 films on substrates; (3) scanning the femtosecond laser beam in the fabricated microgrooves for modi. cation of the inner surfaces; and (4) electroless copper plating. The void-free electroless copper plating is obtained with appropriate cross section of microgrooves and uniform initiation of the autocatalytic deposition on the inner surface of grooves. The dimension and shape of the microelectrodes could be accurately controlled by changing the conditions of femtosecond laser ablation, which in turn can control the distribution of electric field inside LiNbO3 crystal for various applications, opening up a new approach to fabricate three-dimensional integrated electro-optic devices. (C) 2008 Elsevier B. V. All rights reserved.

Mechanism study of femtosecond laser induced selective metallization (FLISM) on glass surfaces

We investigate the mechanism of selective metallization on glass surfaces with the assistance of femtosecond laser irradiation followed by electroless plating. Irradiation of femtosecond laser makes it possible to selectively deposit copper microstructures in the irradiated area on glass surfaces coated with silver nitrate films. The energy-dispersive X-ray (EDX) analyses reveal that silver atoms are produced on the surface of grooves formed by laser ablation, which serve as catalysis seeds for subsequent electroless copper plating. (C) 2008 Elsevier B.V. All rights reserved.

Surface-enhanced Raman scattering substrate fabricated by femtosecond laser direct writing

We report the fabrication of a novel surface-enhanced Raman scattering (SERS) substrate with a controllable enhancement factor (EF) using femtosecond laser direct writing on Ag+-doped phosphate glass followed by chemical plating at similar to 40 degrees C. Silver seeds were first photoreduced using a femtosecond laser in a laser-irradiated area and then transformed into silver nanoparticles of suitable size for SERS application in the subsequent chemical plating. Rhodamine 6G was used as a probing molecule to investigate the enhancement effect of a Raman signal on the substrate. Nearly homogenous enhancement of the Raman signal over the Substrate was achieved, and the EF of the substrate was controlled to some extent by adjusting fabrication parameters. Moreover, the ability of forming a SERS platform in an embedded microfluidic chamber would be of great use for establishing a compact lab-on-a-chip device based on Raman analysis.

Selective metallization on insulator surfaces with femtosecond laser pulses

We report selective metallization on surfaces of insulators ( glass slides and lithium niobate crystal) based on femtosecond laser modification combined with electroless plating. The process is mainly composed of four steps: (1) formation of silver nitrate thin films on the surfaces of glass or crystal substrates; (2) generation of silver particles in the irradiated area by femtosecond laser direct writing; (3) removal of unirradiated silver nitrate films; and (4) selective electroless plating in the modified area. We discuss the mechanism of selective metallization on the insulators. Moreover, we investigate the electrical and adhesive properties of the copper microstructures patterned on the insulator surfaces, showing great potential of integrating electrical functions into lab-on-a-chip devices. (C) 2007 Optical Society of America.

I.小麦非叶器官碳酸酐酶活性与定位分析II.镉毒害导致芦苇胚性细胞死亡的激素调控研究

第一部分： 通过生理测定和化学染色分析了冬小麦品种小堰54和京411的叶片和非叶片组织的碳酸酐 酶活性。叶片碳酸酐酶活性(CA)在挑旗时期达到最大值，之后减少到最小，而在饱粒期又呈 增加趋势。从灌浆期到饱粒期，颖片和内稃的CA活性均减少，而外稃和种皮的CA活性均增加。在饱粒期，小堰54的叶片、颖片、外稃和种皮CA活性均高于京411。组织化学染色表明，CA主要分布在旗叶的叶肉细胞叶绿体中，也分布在非叶片组织颖片、外稃和内稃的叶肉和维管束鞘细胞的胞质中。这些结果表明，小麦非叶组织叶肉和维管束鞘细胞的胞质中的CA可能对饱粒期冬小麦的C4光合途径起作用。饱粒期小堰54的C02传递到Rubisco酶速率和抗旱性较京411高。 第二部分： 以继代培养的芦苇胚性细胞为材料，利用台盼兰拒染法检测了悬浮细胞死亡过程，并利用石蜡切片法及苏木精染色法观察了不同浓度镉对芦苇细胞的毒害作用。1000μM的CdCl2迅速导致芦苇悬浮细胞死亡，200μM的CdClz在接种后第5天引起悬浮细胞死亡，100μM的CdCl2在接种后第7天引起悬浮细胞死亡，≤50μM的CdClz在接种后7天不引起悬浮细胞死亡。同时对不同浓度镉处理的芦苇胚性细胞的内源植物激素和可溶性蛋白质进行分析，≤50μM的镉浓度显著地降低胚性细胞内IAA、ZR、GA3和GA4的含量，却提高ABA的含量，抑制可溶性蛋白质的合成：≥100μM的镉浓度显著地提高IAA、ZR、GA3和GA4的含量，却降低ABA的含量，促进可溶性蛋白质的合成。这些结果表明，镉的毒害至少包括镉浓度决定的两种细胞死亡机制，高浓度的镉(1000μM)引起的细胞死亡应当为坏死，而100μM的镉引起植物悬浮细胞发生程序性死亡。在较高浓度(≥100μM)的镉处理下，芦苇细胞内内源IAA、ZR、GA3和GA4的浓度较高，可能调控可溶性蛋白质的合成而促进细胞发生程序化死亡。