VGIS-COLLIDE: an effective collision detection algorithm for

Collision detection is an important component in simulation applications which are based on virtual geographic information system (VGIS). In this paper, an effective collision detection algorithm for multiple objects in VGIS, VGIS-COLLIDE, is presented. The algorithm firstly integrates existing quadtree, which is the global hierarchical structure of VGIS, with axis-aligned bounding box of object to perform the broad-phase of collision detection. After that, exact collision detection between two objects which have passed the broad-phase of collision detection is performed. The algorithm makes no assumption about input primitives or object's motion and is directly applicable to all triangulated models. It can be applicable to both rigid and deformable objects without preprocessing. The performance of the algorithm has been demonstrated in several environments consisting of a high number of objects with hundreds of thousands of triangles.

Grafting acrylic acid onto polypropylene by reactive extrusion with pre-irradiated PP as initiator

In this paper, the modification of polypropylene (PP) with acrylic acid (AA) by reactive extrusion using pre-irradiated PP (rPP) as initiator was investigated. It was found the relatively high graft degree (Gd) and slight degradation of modified PP was obtained when 20 wt% rPP was used. This result can be explained in terms of effective concentration of free radicals.

PP/s 21,2PB 共混物的非等温结晶动力学

用DSC方法研究了聚丙烯（PP）、PP与间同1，2-聚丁二烯（s-1，2PB）共混物的非等温结晶行为，结果表明：Mo法处理PP及PP侮1，2PB（90／10）共混物是非常适宜的，而用Ozawa法处理则存在缺陷。用Jeziomy法处理共混物也是适宜的，但对PP处理存在缺陷；s-1，2PB对PP有加速结晶的作用；s-1，2PB使PP的结晶活化能降低，s-1，2PB在PP结晶过程中起到异相成核的作用

PP／间同1,2-聚丁二烯的物理力学性能

添加不同质量分数的间同1,2-聚丁二烯(sPB)热塑性弹性体对聚丙烯(PP)共混改性,研究了共混体系的物理力学性能。PP与sPB结构相似,有良好的相容性,随着w(sPB)从0增至40%,共混体系的屈服拉伸强度、弯曲模量及耐热性有所降低;悬臂梁冲击强度增加,且常温悬臂梁冲击强度增幅较大,但低温悬臂梁冲击强度增加较少;断裂伸长率和熔体流动速率先增加后减少。

Online study of the formation of PA6 droplets in PP matrix under shear flow

Breakup process of polyamide 6 (PA6) in polypropylene (PP) matrix under shear flow was online studied by using a Linkam CSS 450 stage equipped with optical microscopy. Both tip streaming and fracture breakup modes of PA6 droplets were observed in this study. It was reported that the droplet would break up by tip streaming model when the radio of the droplet phase viscosity to the matrix phase viscosity (n(r) = n(d)/n(m)) is smaller than 0.1 (Taylor, Proc R Soc London A 1934, 146, 501; Grace, Chem Eng Commun 1982, 14, 225; Bartok and Mason, J Colloid Sci 1959, 14, 13; Rumscheidt and Mason, J Colloid Sci 1961, 16, 238; de Bruijn, Chem Eng Sci 1993, 48, 277). However, the tip streaming model was observed even when the viscosity ratio was much greater than 0.1 (n(r) = 1.9). In this study for the tip streaming mode, small droplets were ruptured from the tip of the mother droplet. On the other hand, the mother droplet was broken into two or more daughter droplets with one or several satellite droplets between them for the fracture mode. It was found that PA6 droplet was much elongated at first, and then broke up via tip streaming or fracture to form daughter droplets or small satellite droplets with the shape of fiber or ellipse.

PP-g-AA接枝共聚物的制备及表征

以部分预辐照聚丙烯(rPP)作为聚丙烯反应挤出接枝丙烯酸(AA)的引发剂,制备了PP-g-AA接枝共聚物。考察了预辐照剂量、预辐照聚丙烯用量以及单体浓度等因素对接枝反应的影响。采用红外光谱、差热扫描量热仪和偏光显微镜等测试技术对接枝产物的形态、结构及性能进行了研究。结果表明,这种新的PP-g-AA共聚物制备方法能有效抑制聚丙烯的降解并获得较高力学性能的接枝产物。研究发现,当rPP的预辐照剂量为4 kGy,反应原料的组成为m(PP)∶m(rPP)∶m(AA)=90∶10∶0.8时,得到的产物有较高的接枝率(0.19%),并且具有相对最佳的力学性能;这种接枝产物与铝板有很强的粘接效果,其剥离强度达4.88 kN/m。

An investigation on the dispersion of montmorillonite (MMT) primary particles in PP matrix

A novel path of preparing PP/o-MMT nanocomposites, which pay attention to the breaking up of MMT original agglomerates and dispersing of its primary particles, rather than the intercalation or exfoliation degree of o-MMT, was reported. The method of predispersing the o-MMT particles into a polar poly(vinyl alcohol) (PVA) matrix and then melt blending the pre-treated PVA/o-MMT hybrids with PP was studied. 3-isopropenyl-alpha,alpha-dimethylbenzene-isocyanate (TMI) was used as a modifier of PVA to improve the compatibility between PVA and PP matrix. Pre-disperse o-MMT with TMI modified PVA was proved to be an effective way to get a composite with fine o-MMT particles dispersion. But the method, which is pre-dispersing o-MMT with non modified PVA and then using TMI to modify such PVA/o-MMT hybrid, would largely reduce the reaction degree between TMI and PVA because of the relatively lower reaction temperature. Although the latter method also can obtain finer dispersion composites than that with using PP-g-MAH as compatibilizer, the relatively higher degradation degree of PP matrix in this method will limit the use of this nanocomposite.

PP/EPDM共混体系的辐射效应

聚丙烯和三元乙丙橡胶(EPDM)的γ辐射效应及辐射后的聚丙烯熔体流动速率的测定表明,在限 定空气中聚丙烯随着辐照剂量的增加,熔体流动速率急剧下降,而三元乙丙橡胶随辐射剂量的增加,凝胶含量 逐渐增加。在20kGy的剂量辐照下,凝胶含量为22.7％,加入2％的三聚异氰酸三烯丙酯,在相同的剂量辐 照下,凝胶含量达到68％。在低剂量下辐照对共混物的拉伸强度影响不大,对冲击强度有很大的影响。在20 kGy的剂量辐照下,加入50％EPDM的聚丙烯的缺口冲击强度由1.95 kJ／m2提高到30 kJ／m2,维卡软化温度 由85.9℃提高到97.0℃。

Preparation of fully cross-linked CNBR/PP-g-GMA and CNBR/PP/PP-g-GMA thermoplastic elastomers and their morphology, structure and properties

Binary CNBR/PP-g-GMA and ternary CNBR/PP/PP-g-GMA thermoplastic elastomers were prepared by reactive blending carboxy nitrile rubber (CNBR) powder with nanometer dimension and polypropylene functionalized with glycidyl methacrylate (PP-g-GMA). Morphology observation by using an atomic force microscope (AFM) and TEM revealed that the size of CNBR dispersed phase in CNBR/PP-g-GMA binary blends was much smaller than that of the corresponding CNBR/PP binary blends. Thermal behavior of CNBR/PP-g-GMA and CNBR/PP blends was studied by DSC. Comparing with the plain PP-g-GMA, T, of PP-g-GMA in CNBR/PP-g-GMA blends increased about 10degreesC. Both thermodynamic and kinetic effects would influence the crystallization behavior of PP-g-GMA in CNBR/PP-g-GMA blends. At a fixed content of CNBR, the apparent viscosity of the blending system increased with increasing the content of PP-g-GMA. FTIR spectrum verified that the improvement of miscibility of CNBR and PP-g-GMA was originated from the reaction between carboxy end groups of CNBR and epoxy groups of GMA grafted onto PP molecular chains. Comparing with CNBR/PP blends, the tensile strength, stress at 100% strain, and elongation at break of CNBR/PP-g-GMA blends were greatly improved.

Fractionated crystallization of dispersed PA6 phase of PP/PP-g-MAH/PA6 blends

Fractionated crystallization behavior of dispersed PA6 phase in PP/PA6 blends compatibilized with PP-g-MAH was investigated by scanning electron microscopy (SEM), differential scanning calorimeter (DSC), polarized light microscopy (PLM), and wide-angle X-ray diffraction (WAXD) in this work. The lack of usual active heterogeneities in the dispersed droplet was the key factor for the fractionated crystallization of PA6. The crystals formed with less efficient nuclei might contain more defects in the crystal structures than those crystallized with the usual active nuclei. The lower the crystallization temperature, the lesser the perfection of the crystals and the lower crystallinity would be. The fractionated crystallization of PP droplets encapsulated by PA6 domains was also observed. The effect of existing PP-g-MAH-g-PA6 copolymer located at the interface on the fractionated crystallization could not be detected in this work.

Relaxation behavior of polymer blends with complex morphologies: Palierne emulsion model for uncompatibilized and compatibilized PP/PA6 blends

This paper deals with the dynamic rheological behavior of polypropylene/polyamide6 (PP/PA6) uncompatibilized blends and those compatibilized with a maleic anhydride grafted PP (PP/PP-g-MAH/PA6). The terminal relaxation times of the blends predicted by the Palierne emulsion model were compared with those obtained from experimental relaxation time spectra. The Palierne model succeeded well in describing PP/PA6 uncompatibilized blends with relatively low dispersed phase contents (10 wt%) and failed doing so for those of which the dispersed contents were high (30 wt%). It also failed for the compatibilized ones, irrespective of the dispersed phase content (10 or 30 wt%) and whether or not interface relaxation was taken into consideration. In the case of the uncompatibilized blend with high dispersed-phase content, interconnections among inclusions of the dispersed phase were responsible for the failure of the Palierne model. As for the compatiblized blends, in addition to particle interconnections, the existence of emulsion-in-emulsion (EE) structures was another factor responsible for the failure of Palieme model.

Compatibilization of PP/EPDM blends by grafting acrylic acid to polypropylene and epoxidizing the diene in EPDM

In this article, ethylene-propylene-diene-rubber (EPDM) was epoxidized with an in situ formed performic acid to prepare epoxided EPDM (eEPDM). The eEPDM together with the introduction of PP-g-AA was used to compatibilize PP/EPDM blends in a Haake mixer. FTIR results showed that the EPDM had been epoxidized. The reaction between epoxy groups in the eEPDM and carboxylic acid groups in PP-g-AA had taken place, and PP-g-EPDM copolymers were formed in situ. Torque test results showed that the actual temperature and torque values for the compatibilized blends were higher than that of the uncompatibilized blends. Scanning electron microscopy (SEM) observation showed that the dispersed phase domain size of compatibilized blends and the uncompatibilized blends were 0.5 and 1.5 mu m, respectively. The eEPDM together with the introduction of PP-g-AA could compatibilize PP/EPDM blends effectively. Notched Izod impact tests showed that the formation of PP-g-EPDM copolymer improved the impact strength and yielded a tougher PP blend.

Brittle-ductile transition in PP/EPDM blends: effect of notch radius

The toughness of polypropylene (PP)/ethylene-propylene-diene monomer (EPDM) blends was studied over wide ranges of EPDM content and temperature. In order to study the effect of notch radius (R), the toughness of the samples with different notch radii was determined from Izod impact test. The results showed that both toughness and brittle-ductile transition (BDT) of the blends were a function of R, respectively. At test temperatures, the toughness tended to decrease with increasing 1/R for various PP/EPDM blends. Moreover, the brittle-ductile transition temperature (T-BT) increased with increasing 1/R, whereas the critical interparticle distance (IDc) reduced with increasing 1/R. Finally, it was found that the different curves of IDc versus test temperature (T) for different notches reduced down to a master curve if plotting IDc versus T-BT(m)-T, where T-BT(m) was the T-BT of PP itself for a given notch, indicating that T-BT(m)-T was a more universal parameter that determined the BDT of polymers. This conclusion was well in agreement with the theoretical prediction.

新型CNBR/PP全交联型热塑性弹性体的制备与形态、结构及性能研究

将具有纳米尺度的全交联型羧基丁腈粉末橡胶 ( CNBR)与聚丙烯 ( PP)及用甲基丙烯酸环氧丙酯( GMA)官能化的聚丙烯 ( PP-g-GMA)进行反应共混 ,制备了一种新型 CNBR/PP热塑性弹性体 .用原子力显微镜 ( AFM)和透射电子显微镜 ( TEM)研究了 CNBR/PP热塑性弹性体的形态 ,加入 PP-g-GMA增容剂后 ,CNBR分散相的粒子尺寸显著降低 ,分布也趋于均一 .与未增容体系相比 ,增容体系的拉伸强度和断裂伸长率均有大幅度的改善 ,如 CNBR含量为 75 %时 ,拉伸强度提高了 94% ,断裂伸长率增加了 1 3 6% .用差示扫描量热法 ( DSC)研究了热塑性弹性体中聚丙烯的结晶行为 ,在增容体系中 ,共混前后聚丙烯的结晶温度提高了 1 0℃ ,表明橡胶粒子或两相界面处形成的反应产物起到了类似成核剂的作用.